Chemistry Commons^™

Preparation And Electrochemical Properties Of Amorphous Znsno3/C By Hydrothermally Carbonization Method, Guo-Qing Fang, Rui-Xue Zhang, Wei-Wei Liu, Bing-Bo Xia, Hong-Dan Sun, Hai-Bo Wang, Jing-Jing Wu, Shinko Kaneko, De-Cheng Li

Journal of Electrochemistry

The amorphous ZnSnO₃@C composite was synthesized via a simple glucose hydrothermal and subsequent carbonization approach. The structure, morphology and electrochemical property of the composite were characterized by XRD, TEM and electrochemical measurements. Compared to bare ZnSnO₃, the ZnSnO₃/C composite exhibited markedly enhanced lithium storage property and cycle performance, delivering a reversible capacity of 659 mAh·g^-1 after 100 cycles at a current density of 100 mA·g^-1.

Synthesis And Electrochemical Property Of Li2Fesio4/C Cathode Material By Solid State Method, Jiao-Li Sun, Zhi-Jiao Chen, Yi-Xiao Li, Hu Cheng

Journal of Electrochemistry

Li₂FeSiO₄/C cathode material was synthesized using Li₂SiO₃ and FeC₂O₄ as raw materials by solid state method. The structure and morphology of the material were characterized by XRD and SEM. The electrochemical properties of the material were studied by constant-current cyclic testing. The results show that Li₂FeSiO₄/C has a good electrochemical performance. The first discharge capacity of Li₂FeSiO₄/C cathode material at 30oC reached 167 mAh∙g^-1 when cycled at 10 mA∙g^-1 between 1.5 and 4.8 V.

Electrochemical Na-Storage Materials And Their Applications For Na-Ion Batteries, Jiang-Feng Qian, Xue-Ping Gao, Han-Xi Yang

Journal of Electrochemistry

Oncoming large scale electric energy storage (EES) requires battery systems not only to have sufficient storage capacity but also to be cost-effective and environmentally friendly. Li-ion batteries for widespread EES applications may be limited due to the constraint of global lithium resource. From the considerations of available resources and environmental impact, Na-ion batteries have potential advantages as next generation secondary batteries and an alternative to Li-ion batteries. However, in the present state of the art, the Na-storage cathodes reported so far are still deficient both in energy density and power capability, while the carbon and alloy anodes for Na-ion batteries …

Synthesis Of Pani/Nihcf Nanocomposite Particles And Eqcm Measurement Of Ion Exchange Properties In Solutions Containing Cd2+, Yu-Jiao Yang, Xiao-Gang Hao, Xu-Li Ma, Zhong-De Wang, Zhong-Lin Zhang, Nian-Chen Han

Journal of Electrochemistry

The PANI/NiHCF nanocomposite particles were synthesized on the CNTs-modified Pt substrate by one-step co-polymerization using cyclic voltammetry. Electrochemical quartz crystal microbalance (EQCM) technique was adopted to investigate the polymerization process of the nanocomposite particles and the mechanism of ion exchange in aqueous solution containing Cd²⁺． The morphology and structure of the as-prepared composite particles were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), and Fourier transform infrared spectroscopy (FT-IR). Combined with cyclic voltammetry (CV) and energy dispersive spectroscopy (EDS), the electrochemical behavior and the mechanism of ion exchange were also investigated in electrolytes of Cd^{2+ …}

A Comparative Study In Pretreatments Of Acid Chemical Wastewater By Electrochemical Oxidation And Ozonation, Han-Shui Liu, Su Yu, Shao-Ping Tong, Chun-An Ma

Journal of Electrochemistry

Under the condition of keeping certain acidity, the pretreatment efficiency of an acid chemical wastewater (pH 0.85) by electrochemical oxidation was compared with that by ozonation. The results showed that the electrochemical oxidation pretreatment could obtain a better result than the ozonation at pH 0.85. After the addition of 2 g·L^-1 NaCl and with the electrochemical oxidation pretreatment at 30 mA·cm^-2, the removal rate of chemical oxygen demand (CODCr) reached 43.4%, and the value of biochemical oxygen demand/chemical oxygen demand (BOD₅/COD_Cr) also increased from 0.034 to 0.14 in 20 minutes, indicating significantly improvement …

Preparation Of Benzoquinone From Phenol By Electrooxidation, Dong-Fang Niu, Cheng-Kai Yu, Xin-Sheng Zhang

Journal of Electrochemistry

The benzoquinone was prepared from phenol by electrooxidation in an H-type cell with cation exchange membrane, in which lead plates were used both as an anode and a cathode, while H₂SO₄ was used as a supporting electrolyte. The effects of current density, concentration of sulphuric acid, concentrations of benzoquinone in electrolyte and extractant on the yields and efficiencies of electrolysis were investigated. Under the optimized conditions of current density being 4 A·dm^-2, concentration of sulphuric acid 1 mol·L^-1, passed charge 3.2 A·h, the yield and current efficiency of benzoquinone could reach 68% and …

Experimental Design Methodology Applied To The Oxidation Of Quinolines In Aqueous Medium By Electro-Fenton Process, Souhaila Trabelsi Souissi, Nihal Oturan, Nizar Bellakhal, Mehmet A. Oturan

Journal of Electrochemistry

The degradation behavior of 8-hydroxyquinoleine sulfate (8-HQS), a model molecule of quinolines, was studied in an aqueous medium by electro-Fenton process using a carbon felt cathode and a platinum anode. The great oxidation ability of this process is due to a large production of hydroxyl radical (OH) by electrochemically induced Fenton’s reagent (H₂O₂, Fe²⁺). Hydroxyl radicals are very powerful oxidizing agents which react on organics up to complete mineralization. A factorial experimental design was used for determining the operating parameters on the degradation of 8-HQS in an aqueous medium. The results showed that the …

Basic Principles And Applications Of Secm In Metal Corrosion, Fa-He Cao, Yan Xia, Wen-Juan Liu, Lin-Rong Chang, Jian-Qing Zhang

Journal of Electrochemistry

Scanning electrochemical microscopy (SECM) is chemical microscopy with higher spatial resolution. After 24 years of development, SECM has been widely applied in mapping and kinetics study of heterogeneous electron transfer in localized processes at solid-liquid or liquid-liquid interfaces. The fundamentals and recent advances of SECM in corrosion applications are described, including SECM mapping and kinetics on localized corrosion of metal or coating. Research work of SECM in corrosion by our group is also introduced. Future applications of SECM in corrosion are highlighted.

Applications Of Spectroscopic Ellipsometry In Corrosion Investigation, Ling-Jie Li, Yu-Ling He, Jing-Lei Lei, Sheng Tao Zhang

Journal of Electrochemistry

As a highly-sensitive and non-destructive in situ technique, spectroscopic ellipsometry has been widely applied in corrosion investigation to acquire the dynamic information of the “electrode-medium” interface during corrosion. This paper lays out some representative demonstrations in several established optical models used to interpret data obtained with spectroscopic ellipsometry in corrosion investigation. In addition, the latest trends in development of this technique are analyzed.

Corrosion Behavior Of A High Strength Low Alloy Steel Under Hydrostatic Pressure In Deep Ocean, Hai-Jing Sun, Li Liu, Ying Li

Journal of Electrochemistry

The corrosion behavior of a high strength low alloy steel (HSLA steel) in 3.5% NaCl solution under hydrostatic pressure (HP) in deep ocean has been investigated by performing weight loss measurement, obtaining potentiodynamic polarization curve and emplying electrochemical impedance spectroscopy (EIS) using the set up for simulation of deep sea environment in laboratory. The results were compared with that at atmospheric pressure and the influence of HP was emphatically discussed. The results revealed identical corrosion mechanism for HSLA steel at 3.5 × 10⁶ Pa and 1 × 10⁵ Pa. Howevere, the development of such a corrosion process was …

Corrosion Resistance Of Low Pressure Cold Sprayed Al Coating On Q235 Steel In Seawater, Xiang-Bo Li, Li-Kun Xu, Shan-Guang Qiu, Jia Wang, Guo-Sheng Huang, Cai-Chang Dong

Journal of Electrochemistry

Taking aluminium (Al) powder mixed with 10% (by volume) of Al₂O₃ powder as raw materials, the Al coating was prepared on the Q235 carbon steel substrate using a portable low pressure cold spraying equipment. Through the measurements of the corrosion potential and potentiodynamic polarization, the electrochemical corrosion behavior of the low pressure cold sprayed Al coating in seawater was studied in comparison with those of the Al coatings deposited with high pressure cold spray and thermal spray processes. At the same time, the surface and cross-section morphologies of these coatings were observed with scanning electron microscope. The …

Corrosion Behavior Of Zinc Covered With Thin Electrolyte Layers Under External Electric Field, Xu-Jie Yuan, Jun-Xi Zhang, Shi-Ming Zhang, Tian Tan, Qi-Meng Chen

Journal of Electrochemistry

The corrosion behavior of zinc covered with thin electrolyte layers (TELs) under an application of external electric field was investigated by performing corrosion potential and cathodic polarization current measurements. The results showed that the Ecorr and ic values first increased and then decreased with the increase of electrolyte layer thickness. Pure zinc exhibited the maximum corrosion potential as the TELs increased to 400 μm under the controls of cathodic process and corrosion products. The application of external electric field resulted in either a negative shift in corrosion potential of zinc or an increase of cathodic current. The effect of external …

Preparation Of Mesoporous Silica Supported Ruthenium Oxides And The Application And Kinetic Study In The Catalysis Of Water Oxidation, Yang Zhang

Open Access Dissertations

Photo-induced water splitting of water into H2 and O2 has been a major focus in the development of clean and renewable energy. The development of viable and efficient catalysts that facilitates O2 production remains the major challenge in the study of the corresponding half-reaction of water oxidation. There are plenty of metal oxides reported active in the catalysis of water oxidation. However, several important performance bench marks of those materials, such as the non-stoichiometric production of O2, slow reaction rate and/or low quantum efficiency, remain to be improved.

Ruthenium oxide (RuO2) has long been known as one of the most …

Electrosynthesis Of Glycerol Carbonate From Co2 And Glycerol, Huan Wang, Mei-Xia Zhu, La-Xia Wu, Xiao-Ming Xu, Xue-Ru Zhao, Jia-Xing Lu

Journal of Electrochemistry

Glycerol carbonate was obtained from glycerol and carbon dioxide under room temperature and normal pressure by electrochemical method. The effects of synthesis conditions, such as cathode, charge, current density and temperature, on the reaction of glycerol and carbon dioxide have been investigated. The yields of 73% were produced by electrosynthesis of carbonate under the optimized condition, which is much higher than that by common catalysis method. The electrochemical behavior of the reaction system has been studied by cyclic voltammetry, through which the reaction process has been proposed.

Influence Of Pretreatment On Electrocatalytic Property For Methanol Oxidation Of Ptru/Wc, Xiao-Ling Lang, Mei-Qin Shi, Ye-Kun Jiang, Chun-An Ma

Journal of Electrochemistry

The surface of tungsten carbide (WC) was treated by potassium hydroxide (KOH) at different pH values for different time. The PtRu/WC composite was prepared by microwave-assisted polyol method. The phase structure of PtRu/WC composites were characterized by XRD. The electrocatalytic activity was tested by cyclic voltammetry and chronoamperometry. The results indicated that with different pH treatments WC became more readily supported on PtRu. When treating WC in KOH at pH = 14, PtRu exhibited the best degree of crystallinity on WC surface, leading to the highest electrocatalytic activity of PtRu/WC. Moreover, the optimized activity of PtRu/WC towards methanol oxidation was …

Synthesis And Electrochemical Properties Of Li(Ni0.5Co0.2Mn0.3)1-2xTiXNbXO2, Yong Tang, Qin-Lin Liao, Xiang-An Guo

Journal of Electrochemistry

The cathode-active materials of layered Li(Ni_0.5Co_0.2Mn_0.3)_1-2xTi_xNb_xO₂（x=0, 0.002, 0.005, 0.01, 0.02）composites were synthesized by the thermal treatment of the coprecipitated precursor at 900 ^oC in air. The effects of Ti-Nb co-dopants on the structural and electrochemical properties of Li(Ni_0.5Co_0.2Mn_0.3)O₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical experiments. The results show that the small amounts of Ti-Nb co-dopants in Li(Ni_0.5Co_0.2Mn_0.3)O₂significantly decreased the degree of cation mixing in …

Effects Of Fluoroethylene Carbonate Additive On Low Temperature Performance Of Li-Ion Batteries, Feng-Ju Bian, Zhong-Ru Zhang, Yong Yang

Journal of Electrochemistry

The effects of fluoroethylene carbonate (FEC) on the low temperature performance of lithium ion phosphate full battery are evaluated by different techniques. By addition of 5 wt% FEC into a commercial electrolyte, effective solid electrolyte interface (SEI) film can be formed on the graphite electrodes, the discharge capacity retention at -40 ^oC was increased from 31.7% to 43.7%, and the discharge voltage plateau of the cell is raised. This is attributed to a reduced charge transfer resistance and a lowered polarization on the graphite electrode by electrochemical impedance spectroscopy (EIS) and reference electrode test.

Research Progress Of Intermediate Layers In Ti-Based Oxide Anodes, Xiu-Li Song, Hui-Min Yang, Zhen-Hai Liang

Journal of Electrochemistry

Titanium (Ti)-based oxide anodes are excellent anode materials which have been applied widely in electrochemical fields all over the world. Adding intermediate layers in Ti-based oxide anodes can improve the conductivity, lengthen the lifetime and strengthen the stability between Ti base and metal oxides active layers of electrodes. This article reviews the research progress of intermediate layers in Ti-based oxide anodes. At the same time, current problems existed in the field of Ti-based oxide anodes are pointed out and future development trend in oxide electrode with intermediate layers is prospected.

Advanced Treatment Of Dyeing Wastewater For Reuse By Electrochemical Oxidation, Fei-Xiang Chen, Chu-Yin Yang, Ming-Ming Zhou, Jia-De Wang

Journal of Electrochemistry

In response to the characteristics of dye wastewater, the electrochemical oxidation of effluents from the biochemical process of dyeing wastewater was studied in the electrochemical reactor using PbO₂/Ti electrode as the anode and stainless steel plate as the cathode. The results revealed that the electrochemical oxidation could simultaneously remove the Chemical Oxygen Demand (COD), ammonia and chromaticity. At the residence time of 60 min and current density of 10 mA·cm^-2, the COD, ammonia, chromaticity, concentration of chloride ion and pH values could meet the water standards for “the reuse of urban recycling water-water quality standard for …

Voltage Reversal Behavior In Microbial-Anode Fuel Cells, En-Ren Zhang, Jun-Le Niu, Lei Liu, Guo-Wang Diao

Journal of Electrochemistry

Voltage reversal behavior was investigated in microbial-anode fuel cells (MFCs). Electricity-producing biofilms were developed on the surface of anodes in MFCs inoculated with mixed inoculum from activated sludge. MFC duplicates generally exhibited different performances with respect to the internal resistance, the voltage output and the discharging duration when operating in batch mode. Voltage reversal was observed to occur first in the MFC with lower performance when connecting MFCs in series. Analysis of electrode potentials indicated that the potentials of microbial anodes quickly shifted to more positive values when enhancing discharge current, resulting in voltage reversal in MFCs. Increasing temperature would …

Using Hydrolyzed Sludge Liquor As The Substrate Of Microbial Fuel Cell, Peng Liang, Chao Guo, Xia Huang

Journal of Electrochemistry

Hydrolyzed sludge liquor was used as the substrate of microbial fuel cell. When the thermal treatment time increased from 2 h to 96 h, pH varied little between 7.4 and 8.0. When the treatment time increased, the conductivity, COD and alkaline condition increased to 2.53 mS·cm^-1, 2520 mg·L^-1 and 800 mg·L^-1, respectively. Meanwhile, the power density increased to 25 W·m^-3. The COD removal increased firstly, then decreased, and finally reached the maximum of 47% at the hydrolyzed time of 6 h. The maximal coulombic efficiency was 71% when the treatment time was 4 …

Electrochemically Switched Ion Exchange Properties Of Pani-Snp Composite Films In Wastewater Containing Ni2+ And Cd2+, Yan-Ting Feng, Jun-Qiang Xiao, Xiao-Gang Hao, Xu-Li Ma, Zhong-De Wang, Nian-Chen Han

Journal of Electrochemistry

Electroactive PANI-SnP composite films were prepared by drop-coating method on Pt electrodes and investigated as electrochemically switched ion exchange (ESIX) materials for the separation of Cd²⁺ from aqueous solutions. The composition and morphology of the composite film were characterized by Fourier transform infrared spectrometer (FTIR) and scanning electron microscope (SEM). In solutions containing 0.1 mol·L^-1 Ni(NO₃)₂ and Cd(NO₃)₂, cyclic voltammetry (CV) and electrochemical quartz crystal microbalance (EQCM) were used to investigate the electrochemical behavior and ion-exchange mechanism of PANI-SnP composite film. The elementary composition of PANI-SnP composite films in both oxidation …

Graphene Quantum Dots Enhanced Electrochemical Performance Of Polypyrrole As Supercapacitor Electrode, Kun Wu, Si-Zhe Xu, Xue-Jiao Zhou, Hai-Xia Wu

Journal of Electrochemistry

With an objective to develop electrode materials with high specific capacitance and good stability, a completely new nanocomposite of Polypyrrole (PPY) and graphene quantum dots (GQD) was successfully obtained through in-situ polymerization of pyrrole in the presence of GQD suspension. The obtained composites with different mass ratios were characterized by X-Ray diffraction (XRD), Fourier transformed infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). GQD enhanced electrochemical performance of PPY and, as supercapacitor electrodes, the PPY/GQD composites with the mass ratio of PPY to GQD at 50:1 showed a competitive specific capacitance of 485 F·g^-1 at a scan rate of …

Electrocatalytic Oxidation Degradation Kinetics Of Oxalic Acid In A Cylindrical Electrochemical Reactor With Ti/Iro2-Ta2O5 Anode, Jing Su, Hai-Bo Lin, Hong Xu, Wei-Min Huang, Ya-Peng He

Journal of Electrochemistry

The electrocatalytic oxidation degradation kinetics of oxalic acid in a cylindrical electrochemical reactor with Ti/IrO₂-Ta₂O₅  as an anode was studied. The relation between instantaneous current efficiency and organic concentration in bulk was established based on the two paths for direct electrochemical oxidations, and the theoretical model was verified by experiments. The experimental resultswere reasonably consistent with the established kinetic model. Furthermore, the competition between the two paths was explored with the modelparameter analysis.

Performance Of The Electro-Oxidation And Electro-Fenton Processes With A Bdd Anode For The Treatment Of Low Contents Of Pharmaceuticals In A Real Water Matrix, Sirs Ignasi, Antonio Garrido Jos, Brillas Enric

Journal of Electrochemistry

Here, we report the performance of electro-oxidation and electro-Fenton with a boron-doped diamond (BDD) anode for the treatment of single and multicomponent solutions containing small amounts of pharmaceutical residues (i.e., 1 mg·L^-1 paracetamol and/or 1 mg·L^-1 salicylic acid) spiked into a real water matrix at pH 3.0. Electro-oxidation was performed in a BDD/Pt cell, whereas electro-Fenton was carried out in a BDD/air-diffusion cell to electrogenerate H₂O₂ at the cathode, always operating at constant current density. It was found that the decay of both pharmaceuticals by electro-oxidation was more rapid in the real water matrix than …

Electrochemical Behavior And Content Determination Of Paeonol At Poly Sudan Ⅲ Modified Electrode, Yan-Jie Zheng, Ai-Lin Liu, Yun Lei, Xin-Hua Lin

Journal of Electrochemistry

The poly SudanⅢ modified electrode was characterized by electrochemical impedance spectroscopy（EIS）and cyclic voltammetry (CV), while the electrochemical behavior of paeonol was studied by cyclic voltammetry (CV). The result shows that the poly Sudan Ⅲ modified electrode exhibits excellent electrocatalytic effect on the oxidation of paeonol. The peak currents of differential pulse voltammetry are linear to the paeonol concentrations over the range of 3.0*10^-7 ~ 2.2*10^-5 mol·L^-1. The detection limit has been estimated to be 5.0*10^-8 mol·L^-1. This method can be used for determination of paeonol content in real sample with satisfactory results.

Effect Of Ethyl Propionate On Low-Temperature Performance Of Lifepo4-Based Li-Ion Battery, Xiao-Ping Li, Lian-Sheng Hao, Wei-Shan Li, Meng-Qing Xu, Li-Dan Xing

Journal of Electrochemistry

A linear carboxylic, ester ethyl propionate (EP), was used as the co-solvent of carbonates, ethylene carbonate (EC), ethyl-methyl carbonate (EMC) and dimethyl carbonate (DMC), and its effect on low-temperature performance of LiFePO₄-based Li-ion battery was studied by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge-discharge test. The application of EP enhances the ionic conductivity of the electrolyte, improves the compatibility of the electrolyte with both LiFePO₄ and graphite materials, and thus improves the low-temperature performance of LiFePO₄-based Li-ion battery. The Li-ion battery using the optimized electrolyte of 1 mol·L^-1 LiPF₆/EC:EMC:DMC:EP …

Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution, Xiao-Juan Zhang, Jing-Jing Wang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The Zn-Al layered double hydroxides (Zn-Al LDHs) and calcined products (Zn-Al CLDHs) were synthesized successfully under a routine air atmosphere. The results showed that both Zn-Al LDHs and Zn-Al CLDHs had obvious flake structures. The corrosion inhibition of Zn-Al CLDHs for steel rebar in NaCl solution was studied by electrochemical techniques. It was found that the corrosion rate of steel rebar decreased significantly after the steel rebar was treated by Zn-Al CLDHs in NaCl solution for 3 h. It was indicated that Zn-Al CLDHs could absorb Cl^- and release OH^- during their reconstruction process, which provided dual protection …

Influences Of The Cinnamic Acid On Zinc Electrodeposition At Glassy-Carbon Electrode, Kai Li, Shen Chen, Shen-Na Liu, Bi-Sang Chen, Heng Lin, Guo-Liang Chen, Qing-Xiang Wang

Journal of Electrochemistry

The influences of cinnamic acid (CIN) on the mechanism of Zn deposition and nucleation kinetics onto glassy-carbon electrode were studied by cyclic voltammetry (CV) and chronoamperometry (CA). The results revealed that the zinc reduction took place via Zn²⁺ + 2e → Zn in the presence of CIN, but the kinetics of zinc deposition was changed and the formation rate of zinc nuclei was accelerated. In the absence of CIN, the mechanism of zinc nucleation followed the 3D-instantaneous diffusion-controlled nucleation, while the 3D-progressive diffusion-controlled nucleation in the presence of CIN. The addition of CIN reduced the nucleation rate, but increased …

Preparation And Characterization Of A Novel Composite Electrolyte Ceria-Sulfate For Intermediate Temperature Solid Oxide Fuel Cells, Ze Tong, Yi-Mei Yin, Jie-Wei Yin, Zi-Feng Ma

Journal of Electrochemistry

A novel composite electrolyte SDC-(Li/Na)₂SO₄ was prepared for intermediate temperature solid oxide fuel cells (ITSOFC). The phase structure and cross-sectional morphology were examined by XRD and SEM, respectively, and the ionic conductivity was investigated by AC impedance in a temperature range of 400 ^oC ~ 700 ^oC in air. It was found that the composite electrolyte was composed of two phases: crystal SDC and amorphous (Li/Na)₂SO₄. The conductivity of the composite electrolyte was significantly larger than that of SDC at intermediate temperatures (550 ^oC ~ 700 ^oC) and increased …