Chemistry Commons^™

Efficient Removal Of Lead Ions From Aqueous Media Using Sustainable Sources On Marine Algae, Hannah Namkoong, Erik Biehler, Gon Namkoong, Tarek M. Abdel-Fattah

Electrical & Computer Engineering Faculty Publications

The goal of this project is to explore a new method to efficiently remove Pb(II) ions from water by processing Undaria pinnatifida into immobilized beads using sodium alginate and calcium chloride. The resulting biosorbent was characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS). Using immobilized U. pinnatifida, we investigated the effect of various factors on Pb(II) ion removal efficiency such as temperature, pH, ionic strength, time, and underlying biosorption mechanisms. For Pb(II) ion biosorption studies, Pb(II) ion biosorption data were obtained and analyzed using Langmuir and Freundlich adsorption models. It …

Hybridization From Guest-Host Interactions Reduces The Thermal Conductivity Of Metal-Organic Frameworks, Mallory E. Decoster, Hasan Babaei, Sangeun S. Jung, Zeinab M. Hassan, John T. Gaskins, Ashutosh Giri, Emma M. Tiernan, John A. Tomko, Helmut Baumgart, Pamela M. Norris, Alan J.H. Mcgaughey, Christopher E. Wilmer, Engelbert Redel, Gaurav Giri, Patrick E. Hopkins

Electrical & Computer Engineering Faculty Publications

We experimentally and theoretically investigate the thermal conductivity and mechanical properties of polycrystalline HKUST-1 metal–organic frameworks (MOFs) infiltrated with three guest molecules: tetracyanoquinodimethane (TCNQ), 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4-TCNQ), and (cyclohexane-1,4-diylidene)dimalononitrile (H4-TCNQ). This allows for modification of the interaction strength between the guest and host, presenting an opportunity to study the fundamental atomic scale mechanisms of how guest molecules impact the thermal conductivity of large unit cell porous crystals. The thermal conductivities of the guest@MOF systems decrease significantly, by on average a factor of 4, for all infiltrated samples as compared to the uninfiltrated, pristine HKUST-1. This reduction in thermal conductivity goes in …

Broadband Dielectric Spectroscopic Detection Of Aliphatic Alcohol Vapors With Surface-Mounted Hkust-1 Mofs As Sensing Media, Papa K. Amoah, Zeinab Mohammed Hassan, Rhonda R. Franklin, Helmut Baumgart, Engelbert Redel, Yaw S. Obeng

Electrical & Computer Engineering Faculty Publications

We leveraged chemical-induced changes to microwave signal propagation characteristics (i.e., S-parameters) to characterize the detection of aliphatic alcohol (methanol, ethanol, and 2-propanol) vapors using TCNQ-doped HKUST-1 metal-organic-framework films as the sensing material, at temperatures under 100 °C. We show that the sensitivity of aliphatic alcohol detection depends on the oxidation potential of the analyte, and the impedance of the detection setup depends on the analyte-loading of the sensing medium. The microwaves-based detection technique can also afford new mechanistic insights into VOC detection, with surface-anchored metal-organic frameworks (SURMOFs), which is inaccessible with the traditional coulometric (i.e., resistance-based) measurements.

Molten Salt Technologies For Advanced Nuclear Fuel Cycles And Molten Salt Reactors, Dimitris Killinger

Theses and Dissertations

This dissertation provides five topics—an assessment of different monitoring and analytical techniques often cited in the literature for molten salt systems and designs for nuclear engineering applications. First, we explored commonly used materials for quasi-reference electrodes in molten chloride salts. Second, the limitations of the electrochemical analysis known as cyclic voltammetry due to the concentration of uranium(III) present were being investigated. Third, we provided an experimental assessment on the development of a spectroelectrochemical cell for interrogating various spectroelectrochemical techniques, namely chronoabsorptometry and chronofluorometry, and their limitations due to the presence of uranium(III) ions. Fourth, a study on the corrosion resistance …

Modeling, Fabrication, And Characterization Of Rf-Based Passive Wireless Sensors Composed Of Refractory Semiconducting Ceramics For High Temperature Applications, Kavin Sivaneri Varadharajan Idhaiam

Graduate Theses, Dissertations, and Problem Reports (ETD)

Real-time health monitoring of high temperature systems (>500^oC) in harsh environments is necessary to prevent catastrophic events caused by structural failures, varying pressure, and chemical reactions. Conventional solid-state temperature sensors such as resistance temperature detectors (RTDs) and thermocouples are restricted by their operating environments, sensor dimensions and often require external power sources for their operation. The current work presents the research and development of RF-based passive wireless sensing technology targeting high temperatures and harsh environmental conditions. Passive wireless devices are generally classified as near-field and far-field devices based on the interrogation distance. Near-field sensors are placed at …

Calcite Depression In Bastnaesite-Calcite Flotation System Using Organic Acids, Emmy Muhoza

Graduate Theses, Dissertations, and Problem Reports (ETD)

Bastnaesite is the primary source of light REEs, namely cerium (Ce), lanthanum (La), praseodymium (Pr), neodymium (Nd), to name a few. Bastnaesite is typically concentrated using the froth flotation beneficiation method. Flotation of bastnaesite suffers from high reagent consumption due to the similar surface characteristics of bastnaesite and associated gangue minerals, including calcite. Additionally, complex stages of high-temperature conditioning are often required to suppress the detrimental impact of dissolved calcium ions on the flotation of bastnaesite. This research seeks to investigate the capabilities of organic acids in the bastnaesite-calcite flotation systems to selectively depress calcite minerals and effectively chelate calcium …

Hydrophobically Modified Isosorbide Dimethacrylates As Biomaterials For Bisphenol A Free Dental Fillings, Bilal Marie

Dissertations

Amalgam and Bisphenol A glycerolate dimethacrylate (BisGMA) are the main dental filling materials in use today. Because of the negative perception of amalgam and its lower esthetic appeal, as well as the desire to replace the endocrine disruptor Bisphenol A, which is the building block of BisGMA, there has been a critical need to search for safer alternatives to these dental filling materials.

Isosorbide is a sugar-based molecule generally recognized as safe. It has been extensively studied as a replacement to the Bisphenol A core in various materials. However, isosorbide is extremely hygroscopic, and water uptake in dental fillings causes …

Bodipy Based Photodynamic Therapy And Potassium Probes, Xiangshan Liu

Dissertations

Boron dipyrromethene (BODIPY) has become more and more popular in photophysical and biological applications. BODIPY based fluorescence compounds have numerous advantage properties including low toxicity, high absorption extinction coefficients, high fluorescence quantum yields, sharp fluorescence emissions, and resistance to photobleaching. All the good properties lead to the wide applications of BODIPY based compounds. In this research, two different kinds of BODIPY are synthesized. Firstly, BDBrC containing carbazole and BODIPY core is synthesized. Cellular uptake research shows BDBrC can target on lysosome and singlet oxygen generation research result indicates that BDBrC can be used in photodynamic therapy. BDBrC also shows pH-sensitive …

Functional Sulfate Electrolytes Enable The Enhanced Cycling Stability Of Nati2(Po4)3/C Anode Material For Aqueous Sodium-Ion Batteries, Shu-Jin Li, Zhi-Kang Cao, Wen-Kai Wang, Xiao-Han Zhang, Xing-De Xiang

Journal of Electrochemistry

Aqueous sodium-ion batteries show promising application in fields of large-scale storage of intermittent renewable energies owing to the earth-abundant sodium resources and incombustible aqueous electrolytes. Primary factors determining whether they can be commercially utilized are low cost and long lifetime. Among current electrode materials, NASICON-type NaTi₂(PO₄)₃ arouses wide interests as an anode material for aqueous sodium-ion batteries as it offers a high specific capacity, fast Na-transport ability and reasonable working potential, however, suffering from insufficient cycling performance caused by severe dissolution of active materials in traditional aqueous electrolytes. In this work, a functional sulfate electrolyte …

Influence Of Heat Treatment Time On Cathode Material Cr8O21 For Lithium Battery, Jiu-Kang Teng, Qing-Jie Wang, Liang Zhang, Hong-Mei Zhang, Xiao-Tao Chen, Peng Zhang, Jin-Bao Zhao

Journal of Electrochemistry

Chromium oxide (Cr₈O₂₁) cathode material for lithium batteries was synthesized by thermal decomposition of chromium trioxide (CrO₃) at high temperature. The electrochemical properties of chromium oxide depended on the time and temperature during the heat treatment. Pure phase chromium oxide was prepared, and the effects of heat treatment time on the structures and electrochemical properties of Cr₈O₂₁ were systematically studied. The first discharge mechanism of chromium oxide in lithium batteries was explored, and the results were similar to that in lithium-sulfur batteries. The crystal phases and electrochemical properties of the prepared …

Effect Of Glycol Based Coolant Pollution On Pem Fuel Cells Stack And Recovery Measures, Cong-Yi Zhu, Xiao-Hui Li, Quan-Quan Gan

Journal of Electrochemistry

As the heat conduction medium of fuel cell cooling system, coolant is very important for the thermal management of fuel cell stack. In practical application, coolant leakage into the stack often occurs. Due to the randomness of fault location of components, the location of coolant leakage is uncertain, which may occur on the cathode side or anode side of some or all single cells. The main effects of coolant pollution on fuel cell stack are as follows: the output of open circuit voltage decreases sharply, the consistency of single cells voltage decreases and so on, which seriously affects the normal …

Formation And Morphological Evolution Of Nanoporous Anodized Iron Oxide Films, Jin-Wei Cao, Nan Gao, Zhao-Qing Gao, Chen Wang, Sheng-Yan Shang, Yun-Peng Wang, Hai-Tao Ma

Journal of Electrochemistry

The preparation of iron oxide films with nanoporous structure by anodization has attracted much attention for its potential applications. However, the formation mechanism of porous structure during anodization is still unclear. In this paper, the composition of anodic current during the formation of nanoporous anodized iron oxide film was analyzed in combination with the current density-potential response (I-V curve) and the derivation of Faraday’s law. The results showed that the anodic current consisted of an ionic current (leading to the migration of ions to form oxide) and an electronic current (leading to the oxygen evolution), and the …

Copper Nanoparticles In-Situ Anchored On Nitrogen-Doped Carbon For High-Efficiency Oxygen Reduction Reaction Electrocatalyst, Hui-Fang Yuan, Yue Zhang, Xing-Wu Zhai, Li-Bing Hu, Gui-Xian Ge, Gang Wang, Feng Yu, Bin Dai

Journal of Electrochemistry

Compared with noble metal platinum (Pt)-based catalysts, inexpensive non-noble metal electrocatalysts have attracted extensive attention for oxygen reduction reaction (ORR). Herein, chitosan as a kind of biomass resource rich in nitrogen and carbon was used to prepare nitrogen-doped carbon (N-C) and N-C in-situ anchored by copper nanoparticles (Cu/N-C). The as-obtained N-C and Cu/N-C nanoparticles were successfully used as non-noble eletrocatalysts tested for ORR. Compared with the N-C, the Cu/N-C showed the high surface area of 607.3 m ²·g^-1 with the mean pore size of 2.5 nm and the pore volume of 0.40 cm³·g^{-1 …}

Nitrogen-Sulfur Co-Doped Porous Carbon Preparation And Its Application In Lithium-Sulfur Batteries, Gui-Xiang Zhao, Wail Hafiz Zaki Ahmed, Fu-Liang Zhu

Journal of Electrochemistry

In recent years, lithium-sulfur (Li-S) batteries have been considered as a promising candidate for the next generation of energy storage system due to their ultrahigh theoretical capacity (1675 mAh·g^-1) and energy density (2600 Wh·kg^-1). However, the practical application of Li-S batteries is seriously limited by their insulating nature of sulfur, the shuttle effect of polysulfides (LiPSs), and volume expansion during charging and discharging. To overcome those disadvantages, one of the commonly methods is to infiltrate sulfur into porous conductive carbon framework, such as porous carbon, hollow carbon spheres, graphene, carbon nanotubes and some composites of the …

Photoelectrochemical Sensing Based On Zr-Mofs For Homocysteine Detection, Wen-Xia Dong, Guang-Ming Wen, Bin Liu, Zhong-Ping Li

Journal of Electrochemistry

Due to the independent form of the light source and detection system, photoelectrochemical (PEC) sensor has the advantages of low background, high sensitivity and simple operation. So far, PEC systems have been widely used in the fields including the actual detection of metal ions, biological antibodies or antigens in environmental pollutants. When the photosensitive material is irradiated by a light source with an energy being equal to or greater than its band gap, electrons (e^-) transition occurs from the valence band to the conduction band, leaving a hole (h⁺), at the same time, the generated electron-hole …

Structure Analysis Of Pemfc Cathode Catalyst Layer, Rui-Qing Wang, Sheng Sui

Journal of Electrochemistry

The sluggish oxygen reduction reaction (ORR) on the cathode of the proton exchange membrane fuel cell (PEMFC) has always been one of the key factors limiting its commercialization. The optimization of the cathode catalytic layer structure plays an important role in improving fuel cell performance and reducing production costs. In this paper, two different catalysts (platinum nanoparticles (Pt-NPs) and platinum nanowires (Pt-NWs)) were prepared by using catalyst coated substrate (CCS) method. By constructing a double-layer catalytic layer structure, we analyzed the effect of different catalytic layer structures by performing a single cell test. The results showed that the dense platinum …

Cyclic Voltammetric Simulations On Batteries With Porous Electrodes, Xue-Fan Cai, Sheng Sun

Journal of Electrochemistry

Lithium-ion batteries (LIBs) are among the most widely used energy storage devices. Whole-cell modeling and simulations of LIBs can optimize the design of batteries with lower costs and higher speeds. The Pseudo-Two-Dimensional (P2D) electrochemical model is among the most famous whole-cell models and widely applied in LIB simulations. P2D model consists of a series of kinetic equations to model Li⁺/Li diffusion in working/counter electrodes and electrolytes, which are filled in the porous electrodes and separator, and reactions at the interface of electrolyte and active particles. The traditional applications of P2D model, however, are limited to the cases where …

Effect Of Aluminum Alloy Surface Modification On Adhesion Of The Modified Polyurethane Coating And Its Corrosion Protective Performance, Xian-Yin Kuang, Shao-Qiang Jin, Yan-Hui Cao, Yan-Mei Zhang, Shi-Gang Dong, Long-Hui Zhu, Li-Wen Lin, Chang-Jian Lin

Journal of Electrochemistry

The ordinary organic coatings on aluminum alloy usually encounter a problem of low adhesion to the substrate, which results in destruction and failure of the long-term protective performance of the anticorrosion systems. The surface modification of aluminum alloy is able to enhance the adhesion of organic coating on aluminum alloys, and to improve their protective performance. In this work, a combined surface modification of anodic oxidation and mussel adhesion protein/CeO₂/3-aminopropyltriethoxysilane composite film (MCA) was developed on the aluminum alloy. The adhesion of modified polyurethane coated on the treated aluminum alloy and its corrosion protective performance were evaluated comprehensively …

Interfacial Engineering And Photoelectrochemistry Of Patterned Metal/Semiconductor Heterostructures, Che Tan

McKelvey School of Engineering Graduate Student Theses & Dissertations

Photoelectrochemical (PEC) cells enable the conversion of solar energy into storable fuels, which is critical in overcoming the intermittent nature of this largest renewable source. However, the majority of semiconductors used as photoelectrodes in these cells have low conversion efficiencies and/or stabilities. Silicon (Si) is an attractive semiconductor material for photoelectrodes, but the development of efficient Si-based photoanodes is challenging due to their instability in alkaline solutions. Thus, one focus of this dissertation is the design and fabrication of highly stable nickel (Ni)-patterned Si photoanodes through interfacial engineering of the barrier heights. Recently, hot carriers in plasmonic metal nanostructures have …

Formation Of Reactive Nitrogen Species During Dichloramine Decay And Their Impact On N Nitrosodimethylamine Formation Under Drinking Water Conditions, Huong Thu Pham

Graduate Theses and Dissertations

NDMA occurrence and formation pathways in drinking water systems are reviewed and NDMA yields are compared on the basis of disinfectant type, water chemistry, and precursor category. In chloramination, despite monochloramine being the predominant species between pH 7-9, evidence suggests that dichloramine is the primary species involved in NDMA formation. This is somewhat confounding as NDMA yields are maximal at pH 9, yet at pH 9 dichloramine decays faster than it forms and hence is present at trace levels; additionally, the proposed mechanism involves a spin-forbidden incorporation of dissolved oxygen as a triplet, which is presumably kinetically slow. This review …

Understanding Students’ Global Interdependence In Science Instruction, Walter S. Smith

Journal of Global Education and Research

Multiple American educational organizations such as the National Education Association, Association for Supervision and Curriculum Development, and the Council of Chief State School Officers have advocated for globalizing the K-12 curriculum. The National Science Teaching Association (NSTA) in a position statement on international education and the Next Generation Science Standards have produced goals and standards for internationalizing the science curriculum by addressing topics such as climate change, environment, and disease that cross borders. In contrast to those pronouncements on the curriculum, this article views global science education through an instructional lens that focuses on a students’ global interdependence in science …

Synthesis And Characterization Of 4,6-Protected Glucosamine Derivatives And Branched Glycoconjugates, Jonathan Bietsch

Chemistry & Biochemistry Theses & Dissertations

Low molecular weight gelators (LMWGs) are small molecules that self-assemble in appropriate solvents to form three dimensional networks that immobilize the solvent, creating a supramolecular gel. The self-assembly of LMWGs occurs through non-covalent interactions such as hydrogen bonding, aromatic interactions, donor-acceptor interactions, Van der Waals interactions, hydrophobic forces, halogen bonding, etc. Due to self-assembly occurring through reversible non-covalent interactions, supramolecular gels can undergo a gel to solution transformation. Because of this, these materials can be sensitive to external stimuli such as temperature changes, pH changes, and other stimuli that effect non-covalent interactions. This makes the synthesis of LMWG’s an appealing …

Super-Adsorbent Hydrogels For Removal Of Methylene Blue From Aqueous Solution: Dye Adsorption Isotherms, Kinetics, And Thermodynamic Properties, Buddhabhushan Salunkhe, Thomas P. Schuman

Chemistry Faculty Research & Creative Works

Removal of dyes through adsorption from wastewater has gained substantial interest in recent years, especially in development of hydrogel-based adsorbents, owing to their easy use and economical nature. The aim of the present study was to design a super-adsorbent hydrogel based on sodium styrene sulfonate (NaSS) monomer for removal of dyes like methylene blue (MB). NaSS displays both an aromatic ring and strongly ionic group in its monomer structure that can enhance adsorption capacity. Poly (sodium styrene sulfonate-co-dimethylacrylamide) hydrogels were prepared by solution free radical polymerization using gelatin meth acryloyl (GelMA) as crosslinker, creating a highly porous, three-dimensionally crosslinked polymer …

Rational Design Of Multifunctional Nanocatalysts For Environmental Remediation And Energy Conversion Technologies, Md Ariful Ahsan

Open Access Theses & Dissertations

The discovery of efficient and sustainable carbon-based nanotechnologies to solve both the scarcity of drinking water and global energy crisis has become a paramount task in the last decades. Owed to the fast population growth and industrialization of the modern society, access to potable water and clean energy technologies is becoming very hard around the globe. Water pollutants have become a serious threat to the environment and ecology because of their toxic nature. Parallelly, the current hydrocarbon-based fuel industries are generating high levels of contamination across the planet, making imperative the development of cleaner energy technologies. In this regard, the …

Identification Of Phosphorous Loading Point Source Facilities To 303(D) Listed Nutrient Impaired Waters Through Watershed Delineation Using Arcgis For Life Cycle Assessment Applications, John Zimmerman

Chemical Engineering Undergraduate Honors Theses

The work done for this project is part of a larger “life cycle assessment (LCA) of novel electrochemical phosphorus recovery technology at the wastewater treatment plant and U.S. watershed scales” (Morrissey 2019). The goal of that LCA is to determine “environmental impacts of implementing electrochemical struvite recovery at the wastewater treatment plant, U.S watershed, and global scales” (Morrissey 2019). This project’s goal is to identify locations deemed more sensitive to eutrophication impacts. The results will be used as part of the life cycle inventory (LCI) accounting for geographically explicit phosphorus flows. The waters identified as impaired were sourced from the …

Synthesis, Crystal Structure And Ionic Conductivity Of Ruddlesden-Popper Oxide Materials: Effects Of Ionic Radii And Defects On Lithium-Ionic Conductivity., Selorm Joy Fanah

Electronic Theses and Dissertations

Layered perovskite oxides of the Ruddlesden-Popper (RP) type structure can be good lithium-ion conductors for solid electrolyte applications in all-solid-state batteries, due to the large gap separating octahedral layers which can be useful pathways for Li-ion conduction. However, little work has been done on their lithium-ion transport properties in these materials despite their interesting structural properties. This work highlights the synthesis and study of the ionic conductivities in a series of n = 2 and 3 Ruddlesden-Popper oxides, as part of an ongoing investigation in search of alternative solid electrolyte materials. Several different strategies were employed for the enhancement of …

Synthesis, Characterization, And Direct-Ink-Writing Of Syntactic Foams, Andrea Irigoyen

Open Access Theses & Dissertations

This project encompasses three different methods to fabricate syntactic foams using a PDMS matrix i.e., hollow spheres inclusion, pore generator leaching by solvent, and emulsion. The foam formation by using polysiloxane hollow spheres is done in a 3-step process. The first step is to create a core of polystyrene following a dispersion polymerization process. The goal for the size of the pore is to monodisperse and have an average diameter of 5-10 μm, so the polystyrene core must be as well within that range. After that, the cores are coated with a polysiloxane shell by following a polymerization by condensation …

Erratum: Physicochemical Insights Of Irradiation-Enhanced Hydroxyl Radical Generation From Zno Nanoparticles(Toxicology Research Doi: 10.1039/C5tx00384a), Qingbo Yang, Tien Sung Lin, Casey Burton, Sungho Park, Yinfa Ma

Electrical and Computer Engineering Faculty Research & Creative Works

In the originally published version of this manuscript, the fourth author's name is incorrect. The name should read "Sungho Park", instead of "Sung-Ho Park". These details have been corrected only in this corrigendum to preserve the published version of record.

Synthesis Of Polyethylene Glycol-Based Hydrogels And Silver/Gold Nanostructures For Biomedical Applications, Isabelle Ishimwe Niyonshuti

Graduate Theses and Dissertations

This work focuses on the synthesis of biocompatible polyethylene glycol (PEG)-based hydrogels, silver nanoparticles (AgNPs), and silver-gold nanocages (Ag-AuNCs) for biomedical applications. The dissertation includes two parts with Part I on the work of PEG-based hydrogel for wound healing applications and Part II on the work of Ag/Au nanostructures for antimicrobial applications. Part I studies PEG-based hydrogel for the delivery of fibroblast growth factors (FGFs) for wound healing applications, aiming to overcome the challenge of designing hydrogels capable of the sustained release of bioactive FGFs. This research develops new biocompatible anionic injectable hydrogel formulations based on Poly (Oligo Ethylene Glycol …

Multifunctional Programmable Self-Assembled Nanoparticles In Nanomedicine, Yoshie Sakamaki

Graduate Theses and Dissertations

Developing methodologies to control the architecture of nanoparticles (NPs) at the atomic level prevents their inhomogeneity and leads to a variety of expected functions. Rationally designed nanoparticles can either be programmed or crystallized structures into pre-determined structures achieving tunable particle pore size and physiochemistry. In this dissertation, two broad classes of multifunctional nanoparticles are developed, metal-organic frameworks and DNA-NP aggregates.

Metal-organic frameworks are a novel class of highly porous crystalline materials built from organic linkers and metal cluster-based secondary building units. However, applications in bioremediation have not been developed very well especially in applications regarding drug delivery systems (DDS). The …