Chemistry Commons^™

Effect Of Corrosion Inhibitors On Copper Etching To Form Thick Copper Line Of Pcb In Acidic Etching Solution, Xiao-Li Wang, Wei He, Xian-Ming Chen, Hong Zeng, Yuan-Zhang Su, Chong Wang, Gao-Sheng Li, Ben-Xia Huang, Lei Feng, Gao Huang, Yuan-Ming Chen

Journal of Electrochemistry

The chemical compounds of 2-mercaptobenzothiazole (2-MBT), benzotriazole (BTA) and phenoxyethanol (MSDS) as corrosion inhibitors were used to inhibit the copper etching to form the thick copper line of PCB in the acidic etching solution. The inhibition status was characterized with contact angle measurement, electrochemical test and etch factor calculation, while the corrosion morphology of copper surface was studied by scanning electron microscope. The adsorption mechanism of corrosion inhibitors on copper surface is analyzed by molecular dynamics and quantum chemistry calculations. The results indicated that the synergistic function of the two inhibitors could effectively promote their adsorption on the copper surface …

Mechanism And Application Of Nickel Nano-Cone By Electrodeposition On A Flexible Substrate, Xiu-Ren Ni, Ya-Ting Zhang, Chong Wang, Yan Hong, Yuan-Ming Chen, Yuan-Zhang Su, Wei He, Xian-Ming Chen, Ben-Xia Huang, Zhen-Lin Xu, Yi-Feng Li, Neng-Bin Li, Yong-Jie Du

Journal of Electrochemistry

Nano-array structure possesses promising prospect in power supply, optical device and electronic manufacturing. In this paper, a black nickel nano-cone array was prepared on a flexible substrate by galvanostatic deposition and the corresponding factors involved in the fabrication of nickel nano-cone array was explored. Experimental results showed that a large current density and low main salt concentration were not favored to the formation of cone nickel structure. It was also found that ammonium chloride, as the crystal modifier, was crucial to deposit the uniform nano-cone array. In addition, the growth mechanism of nickel nano-cone was further studied by molecular dynamics …

Electrodeposition Of Functional Epitaxial Films For Electronics, Kui Huang, Rong-Jiao Huang, Su-Qin Liu, Zhen He

Journal of Electrochemistry

Electrodeposition is a solution-based synthesis technique that can be used to fabricate various functional materials on conductive or semiconductive substrates under ambient conditions. Electrodeposition is usually triggered by an artificial electric stimulation (i.e., applied potential/current) to the substrate to oxidize or reduce ions, molecules, or complexes in the deposition solution layer near the substrate surface, which drives this solution layer to depart from its thermodynamic equilibrium and consequently causes the assembly of targeted deposits on the substrate. During electrodeposition, many experimental parameters could affect the properties of the deposits in different ways. To date, many elements (both metals and nonmetals), …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

A Protein-Based Therapeutic Combination For The Treatment Of Hard-To-Heal Wounds, Graham L. Strauss

USF Tampa Graduate Theses and Dissertations

Chronic wounds present many clinical challenges in relation to the successful treatment and closure of the damaged tissue. Most current treatment methods focused on one or two aspects to drive wound closure, while most chronic wounds are multifactorial environments with many of those dependencies relying on the termination of one another to effectively gain tissue construction, closure, and full skin thickness and composition. Natural wound healing processes allude to potential biologics that can impede the chronic breakdown of tissue, while restoring deposition of new tissue, and effectively leading to a healed wound. Proteases secreted by the body’s immune system lay …

Large Area Projection Sintering Of Semicrystalline Polymers And Part Analysis Of The Printed Specimens, Taranjot Kaur

USF Tampa Graduate Theses and Dissertations

As the requirements posed to products have increased in recent years. The trend towards individualized serial products steps up the need for respective manufacturing techniques to be more and more flexible. Conventional techniques of serial production, such as injection molding, are unable to fully meet the requirements of this trend. Additive manufacturing techniques generate components directly from a CAD data set while requiring no specific mold, producing minimal waste, and reaching satisfactory geometric accuracy. This is how, as opposed to conventional techniques, they comply with these increased demands to processing technology. Over the last two decades, the research community has …

Evaluation Of The Energetic Factors In Crystalline Pharmaceuticals Using Solid-State Density Functional Theory And Low-Frequency Vibrational Spectroscopy, Margaret P. Davis

Dissertations - ALL

Due to the importance of maintaining stable and effective pharmaceutical solid doses, it is critical to study the variety of solid forms that active pharmaceutical ingredients can adopt including polymorphs, hydrates, and cocrystals. In this work, low-frequency vibrational spectroscopies and rigorous quantum mechanical simulations are combined to provide a new technique for characterizing and investigating pharmaceutically relevant polymorphs, hydrates, and cocrystals as well as a series of model cocrystals. Low-frequency spectra in the sub-200 cm-1 range provide not only unique and characteristic spectra for all of the systems explored here but, along with X-ray structural parameters, they offer a way …

Table Of Contents

Journal of the South Carolina Academy of Science

No abstract provided.

Carbon Monoxide Oxidation On Model Planar Titania Supported Platinum Nanoparticles Catalyst, Jovine Emmanuel, Brian Hayden

Tanzania Journal of Science

A high-throughput (parallel) thermographic screening methodology was developed to enable the measurements of the particle size and support influence on heterogeneous catalysts. A high throughput screening chip has been used to establish the catalytic activity of titania supported platinum nanoparticles catalyst for CO oxidation reaction. The catalytic activity of Pt nanoparticles between 1.3 to 7.8 nm has been investigated for CO conversion at a pressure of 0.11 and 1.1 mbar with O2:CO ratio of 1:1 at 80 °C and 0.6, 1.1 and 2.4 mbar at O2:CO ratio of 1:1 at 240 °C. At these experimental conditions, there was an increase …

Introduction Of Development And Application Technology Of Organic Additives For Acid Copper Electroplating, Hao-Bin Zou, Chao-Li Tan, Wei Xiong, Dao-Lin Xi, Bin-Yun Liu

Journal of Electrochemistry

Acid copper electroplating is one of the key technologies in buildup multilayer PCB (BUM-PCB) manufacture process and the most important technique to achieve electrical interconnection between any layer and high-density interconnection in a substrate. This article introduces the research focus of organic additives used in acid copper electroplating, and developing different kinds of micro-via filling copper electroplating technique applied in various scenarios, and some other technical problems from applications. First of all, according to the chronopotentiometric (CP) experiment results, the levelers with different polymeric molecular structures exhibited various responses of cupric deposition potential along with their increased concentrations, which is …

Study On The Effect Of Additives In The Electrodeposition Of Sn-Ag-Cu Ternary Alloy Solder, Hua Miao, Ming-Rui Li, Wen-Zhong Zou, Guo-Yun Zhou, Shou-Xu Wang, Xiao-Jing Ye, Kai Zhu

Journal of Electrochemistry

Sn-Ag-Cu ternary alloy is the most ideal substitute for Sn-Pb alloy at present, and can be prepared by electrodeposition with high production efficiency, simple equipment, easy maintenance and excellent coating performance. The coordination system of the electroplating solution was investigated through the Hull cell experiment. The type of brighteners used in the plating solution and the ratio of the two brighteners were determined through the microscopic morphologic characterization, electrochemical corrosion test and cathodic polarization curve test. In addition, the dispersant and stabilizer were studied by observing the microscopic morphology and measuring the concentration change of Sn²⁺ ions in the …

Optimization Of Pulse Plating Additives And Plating Parameters For High Aspect Ratio Through Holes, Kai Yang, Ji-Da Chen, Shi-Jin Chen, Wei-Lian Xu, Mao-Gui Guo, Jin-Chao Liao, Zeng-Kun Wu

Journal of Electrochemistry

As an important component in electronic products, printed circuit board (PCB) plays a supporting and interconnecting role for the electronic components in it. With the development of communication technology, electronic products are developing in the direction of “thin, light and small”, and high density interconnection (HDI) comes into being. Due to the high-density interconnection characteristics of HDI boards, the thickness of the board is increasing. At the same time, in order to reserve space for the laying of fine lines on the subsequent board surface, the diameter of the through holes on the board is also decreasing, so the depth-diameter …

An Investigation On The Interface Corrosion Behaviors Of Cobalt Interconnects In Chemical Mechanical Polishing Slurry, Kai-Xuan Qin, Peng-Fei Chang, Yu-Lin Huang, Ming Li, Tao Hang

Journal of Electrochemistry

Cobalt is widely regarded as the most promising interconnect material for 10 nm node and beyond. The development of a chemical mechanical planarization (CMP) slurry suitable for cobalt interconnect is a critical component for the application of cobalt interconnect. During CMP process of the interconnect layer, the achievement of high-quality surface after planarization is greatly challenged by the metal corrosion in CMP slurry. In this contribution, the corrosion behavior of cobalt in a slurry with potassium persulfate (KPS) as an oxidizer, glycine as a complexing agent, and benzotriazole (BTA) as an inhibitor was investigated. Static erosion rates (SER) of cobalt …

Research Progresses Of Cobalt Interconnect And Superfilling By Electroplating In Chips, Li-Jun Wei, Zi-Han Zhou, Yun-Wen Wu, Ming Li, Su Wang

Journal of Electrochemistry

Copper interconnect using dual damascene technology has always been the main means for metallization in the back end of line process. However, with the size effect becoming more and more obvious due to feature size reduction, copper interconnect can no longer meet the demand for high circuit speed in Post-Moore era. Following copper interconnection, cobalt interconnection in chips attracts much attention as an interconnect technology by the next generation, which has been introduced in 7 nm node of integrated circuit manufacturing and below. The electron mean free path of cobalt (~10 nm) is much shorter than copper’s (39 nm), thus …

Electrochemical Sers Study Of Benzotriazole And 3-Mercapto-1-Propanesulfonate In Acidic Solution On Copper Electrode, Yin-Fei Shen, Yan-Li Chen, Sheng-Xu Wang, Ye Zhu, Wen-Chang Wang, Min-Xian Wu, Zhi-Dong Chen

Journal of Electrochemistry

Since the development of acid copper plating technology, the role of additives is indispensable. In addition to the main salt copper sulfate and supporting electrolyte sulfuric acid, suppressors, accelerators, levelers and chlorine ions (Cl^-) are also required to be added into the plating solution. Appropriate additive system can have a significant impact on the coating or the plating solution, which can help improve the quality of the coating and increase the brightness of the coating. Through electrochemical measurement, vibrational spectroscopy, scanning probe microscopy, molecular dynamics simulation and other methods, researches have a deeper understanding in the adsorption configuration …

Development Status Of Copper Electroplating Filling Technology In Through Glass Via For 3d Interconnections, Zhi-Jing Ji, Hui-Qin Ling, Pei-Lin Wu, Rui-Yi Yu, Da-Quan Yu, Ming Li

Journal of Electrochemistry

With the slow development of Moore's Law, the high density and miniaturization of microelectronic devices put forward higher requirements for advanced packaging technology. As a key technology in 2.5D/3D packaging, interposer technology has been extensively studied. According to different interposer materials, it is mainly divided into organic interposer, silicon interposer and glass interposer. Compared with the through silicon via (TSV) interconnection, the through glass via (TGV) interposer has received extensive attention in the 2.5D/3D advanced packaging field for its advantages of excellent high-frequency electrical characteristics, simple process, low cost, and adjustable coefficient of thermal expansion (CTE). However, the thermal conductivity …

Study On Low Voltage Electrodeposition Of Diamond-Like Carbon Film, Li Wang, Min-Xian Wu, Jun Li, Yan-Li Chen, Wen-Chang Wang, Zhi-Dong Chen

Journal of Electrochemistry

Diamond-like carbon (DLC) films are receiving a lot of attention from the scientific community, thanks to the promise of DLC films for applications in microelectronics and optoelectronics. Usually, electrodeposition is the preferred common technique because of low cost, large deposition area and simplicity of the setup. However, when carbon films are electrodeposited on a stainless steel, high cell voltages (≥1000 V) are required owing to the low electric conductivity of the organic solvents. This work has developed a new electrolyte system that could achieve carbon deposition on a stainless steel under a low applied cell voltage. The DLC films were …

Effect Of Sodium Alcohol Thiyl Propane Sulfonate On Electrolysis Of High Performance Copper Foil For Lithium Ion Batteries, Sen Yang, Wen-Chang Wang, Ran Zhang, Shui-Ping Qin, Min-Xian Wu, Naotoshi Mitsuzaki, Zhi-Dong Chen

Journal of Electrochemistry

Electrolytic copper foils have been widely used in printed circuit boards and lithium-ion batteries due to their simple production process and high economic value. In the process of electrolysis foil making, additives can greatly improve the performance of electrolytic copper foils. In this work, the copper foils were prepared in a self-designed plate electrodeposition device of which the operating principles were in accordance with those of actual industrial production. A series of the Virgin Make-up Solution (VMS: 312.5 g·L^-1 CuSO₄·5H₂O, 100 g·L^-1 H₂SO₄, 50 mg·L^-1 Cl^-) containing …

Microstructure Of Electrodeposited Copper Foil: Discussion On The Mechanism Model Of Three-Dimensional Electrocrystallization, Ren-Zhi Liu, Ping-Ling Xie, Chong Wang

Journal of Electrochemistry

The manufacturing of electrolytic copper foil has attracted more and more attention with the extensive applications of printed circuit board and lithium battery. The industrial scale is still extending. Compared with the developments of electroplating equipment and electroplating process, there is limited research on the mechanism of electrodeposition. This paper summarizes the manufacturing process of electrodeposited copper foil and analyzes the differences of various electroplating parameters in different electrodeposited copper technologies, and points out the important role of electrodeposition current density in the formation of copper foil. By showing and comparing the microstructures of different electrodeposited copper foils, the influences …

Improved Performance Of Silica-Supported La0.5Ba0.5Feo3 In The Reverse Water Gas Shift - Chemical Looping Process For Carbon Dioxide Reduction – A Density Functional Theory Study, Jiawei Guo

USF Tampa Graduate Theses and Dissertations

Global warming is increasingly obvious, and the reduction of greenhouse gases is an effective way to heal. Increasing the efficiency of catalysts that is applied in the industry can significantly reduce the emission of greenhouse gases. Reverse water gas shift chemical looping (RWGS-CL) is a promising reaction to convert CO2 to CO. La0.5Ba0.5FeO3 (LBF) is a good candidate for RWGS-CL, which shows increased conversion yield when supported on silica. This research focuses on identifying the mechanism of RWGS-CL via silica-supported LBF by exploring the oxygen vacancy formation energy (EO-vac). Density Functional Theory (DFT) is a powerful computational method to solve …

Examining Metal Contents In Primary And Secondhand Aerosols Released By Electronic Cigarettes, Kashala Fabrice Kapiamba, Weixing Hao, Stephen Adom, Wenyan Liu, Yue-Wern Huang, Yang Wang

Chemistry Faculty Research & Creative Works

The usage of electronic cigarettes (ECs) has surged since their invention two decades ago. However, to date, the health effects of EC aerosol exposure are still not well understood because of insufficient data on the chemical composition of EC aerosols and the corresponding evidence of health risks upon exposure. Herein, we quantified the metals in primary and secondhand aerosols generated by three brands of ECs. By combining aerosol filter sampling and inductively coupled plasma mass spectrometry (ICP-MS), we assessed the mass of metals as a function of EC flavoring, nicotine concentration, device power, puff duration, and aging of the devices. …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

Comprehensive Review Of Polymer And Polymer Gel Treatments For Natural Gas-Related Conformance Control, Ali Al Brahim, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Conformance problems often exist in natural gas-related activities, resulting in excessive water production from natural gas production wells and/or excessive natural gas production from oil production wells. Several mechanical and chemical solutions were reported in the literature to mitigate the conformance problems. Among the chemical solutions, two classes of materials, namely polymer gels and water-soluble polymers, have been mostly reported. These systems have been mainly reviewed in several studies for their applications as water shutoff treatments for oil production wells. Natural gas production wells exhibit different characteristics and have different properties which could impact the performance of the chemical solutions. …

Atmospheric Mercury Chemistry: Detection, Kinetics, And Mechanism, Na Mao

Dissertations

The presence of mercury in the environment is of global concern due to its toxicity. The atmosphere is an important transient reservoir for mercury released by human activities and natural sources. The knowledge of atmospheric mercury chemistry is critical for understanding the global biogeochemical cycle. In the atmosphere, mercury primarily exists in three forms: gaseous elemental mercury (GEM), gaseous oxidized mercury (GOM), and particulate-bound mercury (PBM). Over the last decade, the existing knowledge of mercury cycle has dramatically changed: (1) There has been increasing evidence that current detection methods do not accurately quantify gaseous oxidized mercury and a technique which …

Electrochemical Synthesis Of Acetylpyrazine, Lin Mao, Dong-Fang Niu, Shuo-Zhen Hu, Xin-Sheng Zhang

Journal of Electrochemistry

Acetylpyrazine is naturally presented in hazelnuts, peanuts, and sesame seeds. As an important food additive, it is widely used in baked foods, meat, sesame and tobacco. At the same time, acetylpyrazine is also an important pharmaceutical intermediate, which is used in the syntheses of anti-tuberculosis drugs, anti-tumor, anti-malaria, anti-viral, antibacterial and treatments of epilepsy, pain and Parkinson’s drugs. At present, the synthesis methods of acetylpyrazine include oxidation method, multi-step method and Grignard reagent method, which have the disadvantages of low yield, cumbersome process, severe reaction conditions and high cost. In this study, acetylation of pyrazine was used to synthesize acetylpyrazine …

Electrochemical Voltammetric Behavior Of Sulfur Mustard On The Bare Pt Electrode, Yu-Lin Yang, Jie Sun, Tian Zhou, Ji-Gang Li, Shou-Ping Wei

Journal of Electrochemistry

The sulfur mustard (bis(2-chloroethyl) sulphide, HD), one of highly toxic chemical weapon agents, can damage the alive tissue cells (such as skin, lung, respiratory mucosa and so on), and cause carcinogenic and mutagenic effects for a long time exposure, which imposes a great threat not only to the human health, but also to the sustainable development of the society. With its convenience, high sensitivity and rapid response, electrochemical technology exhibits considerable potential in the field-deployed detection toward HD, but the related reports are rare. Herein, the electrochemical behavior of HD on the bare Pt electrode was investigated by electrochemical measurements, …

Electrocatalytic "Volcano-Type" Effect Of Nano-Tio2 (A)/(R) Phase Content In Pt/Tio2-CnX Catalyst, Ai-Lin Cui, Yang Bai, Hong-Ying Yu, Hui-Min Meng

Journal of Electrochemistry

The relationship between the electrochemical activity of fuel cell catalysts and Pt particle size, as well as the catalyst support and co-catalyst is still unclear. In this work, FESEM, XRD, BET, TEM and CV techniques were adopted to investigate the effects of TiO₂ anatase (A)/rutile (R) phases content on the electrochemical activity of Pt electrocatalyst. The results showed that the anatase-rutile phase transformation occurred during the heat treatment of TiO₂ at 700 ~ 900 ^oC accompanied by the growth of two-phase crystalline size, and anatase was completely transformed into rutile at 900 ^oC. TEM results revealed …

Biofouling Behaviors Of Pure Titanium Surface Polarized At Different Potentials, Zhao-Xia Dai, Da-Jiang Zheng, Guang-Ling Song, Dan-Qing Feng, Pei Su

Journal of Electrochemistry

Titanium (Ti) and its alloys are commonly used as engineering materials. Although they have been widely used in marine environments, they are also facing serious threats of biofouling. Therefore, it is necessary to investigate the relationship between electrochemical behavior and bioaffinity of titanium oxide film in seawater to explore effective surface treatment technology to reduce biofouling. In this work, the cathodic potential of -0.8 V_SCE and the passivation potential of 0.5 V_SCE were directly applied to the TA2 Ti in artificial seawater for potentionstatic polarization treatment to prepare two kinds of surface films with different states and then …

Simultaneous Hydrogen And (Nh4)2So4 Productions From Desulfurization Wastewater Electrolysis Using Mea Electrolyser, Ju-Cai Wei, Lin Shi, Xu Wu

Journal of Electrochemistry

It is preferred to simultaneously recover resource and energy from waster. Sulfur dioxide, SO₂, a common air pollutant, a potential energy resource, is a key link to sulfur nature circulation. SO₂ can be conversed to NH₄HSO₃ and (NH₄)₂SO₃ during the ammonia desulfurization process, which can be used to produce (NH₄)₂SO₄ fertilizer. For high quality (NH₄)₂SO₄ fertilizer and high heat transfer efficiency of the evaporative crystallization, HSO₃^- or SO₃^2- needs to be oxidized to form SO …

Study And Improvement On Expansion Property Of Silicon Oxide, Wei-Chuan Qiao, Fang-Ru Li, Jin-Lin Xiao, Li-Juan Qu, Xiao Zhao, Meng Zhang, Chun-Lei Pang, Zi-Kun Li, Jian-Guo Ren, Xue-Qin He

Journal of Electrochemistry

The silicon-based anode materials have the potential to meet the ever-increasing demand for energy density in lithium-ion batteries market owing to their high theoretical specific capacity. Unfortunately, their commercialization was hindered by the continuous volume expansion. Herein, the expansion characteristics and corresponding mechanism of the silicon oxide and graphite-silicon oxide composites were investigated by in-situ displacement detection systematically. The results showed that the expansion property was improved by material process modifications. During the de/lithiation processes of graphite, the expansion ratio in 30% ~ 50% SOC changed little because of the small interlayer spacing variation of the intercalated graphite. …