Chemistry Commons^™

Interaction Between Metal Fission Products And Triso Coating Materials: A Study Of Chemical Bonding And Interdiffusion, Clemens Heske

Fuels Campaign (TRP)

The goal of this project is to elucidate the chemical bonding and interface formation of metal fission products with the coating materials used in state-of-the-art TRISO fuel particles. Particular emphasis is placed on an analysis of intermediate chemical phases at the interface, the intermixing/diffusion behavior, and the electronic interface structure as a function of material choice (metal and coating materials), temperature, and external stress. Furthermore, we intend to assess the chemical state of some of the metal fission products. The findings are expected to give valuable information about failure mechanisms of TRISO particles and fission product transport. Secondly, through simulating …

Interaction Between Metal Fission Products And Triso Coating Materials: A Study Of Chemical Bonding And Interdiffusion: 3rd Quarter Report, 2004, Clemens Heske

Fuels Campaign (TRP)

The goal of this project, which started in May 2004, is to elucidate the chemical bonding and interface formation of metal fission products with the coating materials used in state-of-the-art TRISO fuel particles. Particular emphasis is placed on an analysis of intermediate chemical phases at the interface, the intermixing/diffusion behavior, and the electronic interface structure as a function of material choice (metal and coating materials), temperature, and external stress.

In detail, this project is devoted to studying the interface formation of Pd, Ag, and Cs with SiC and pyrolytic carbon. Using the TRISO coating materials and single crystal references as …

Interaction Between Metal Fission Products And Triso Coating Materials: A Study Of Chemical Bonding And Interdiffusion: 4th Quarter Report, 2004, Clemens Heske

Fuels Campaign (TRP)

The goal of this project, which started in May 2004, is to elucidate the chemical bonding and interface formation of metal fission products with the coating materials used in state-of-the-art TRISO fuel particles. Particular emphasis is placed on an analysis of intermediate chemical phases at the interface, the intermixing/diffusion behavior, and the electronic interface structure as a function of material choice (metal and coating materials), temperature, and external stress. In detail, this project is devoted to studying the interface formation of Pd, Ag, and Cs with SiC and pyrolytic carbon. In order to study the properties of the relevant interfaces, …

Afci Quarterly Input – Unlv October Through December, 2003, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Inside Unlv, Gian Galassi, Katrina Hudak, Carol C. Harter, Eric Sandgren, Tom Hagge

Inside UNLV

No abstract provided.

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Fourth Quarterly Report 09/01/2003-11/30/2003, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Electrochemical And In-Situ Scanning Tunneling Microscopy Studies On The Sb Underpotential Deposition On Cu Single Crystal Electrodes, Ji-Hong Wu, Jia-Wei Yan, Jing Tang, Wen-Yun Hu, Bing-Wei Mao

Journal of Electrochemistry

We report electrochemical and in-situ STM studies on Sb UPD onto Cu(111) and Cu(100) electrode surfaces in HClO₄ and H₂SO₄ solutions. The results indicate that the electrode surface structure as well as anion can considerably influence Sb UPD. Sb UPD on Cu(100) forms open adlayer structures, which is accompanied by surface alloying due to the more open structure of the (100) surface, On Cu(111), a more compact Sb adlayer is formed instead. Anion adsorption influences the dynamics as well as the adlayer structure of Sb UPD. Owing to the strong adsorption of SO₄^2-, …

Study On Electrochemical Behavior Of Sus316l Stainless Steel After Surface Modification, Cheng-Hao Liang, Liang Guo, Wan Chen, Jing-Xiao Liu

Journal of Electrochemistry

The surface modification for SUS316L stainless steel was carried out by electroplating Rh, ion beam assisted deposition Ta₂O₅ and sol-gel-derived TiO₂. In Tyrode's stimulated body fluid, the surface modified samples had been investigated with electrochemical techniques. The results indicated that the electrochemical stability and dissolution were improved significantly after surface modification. Moreover, as to ion beam assisted deposition Ta₂O₅ and Sol-gel-derived TiO₂ film, the metal's d orbit electron holes filled up by the oxygen electrons made against the adsorption of hydrogen. Thus the cathode process, which is controlled by the hydrogen …

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang

Journal of Electrochemistry

In this work, potential-modulation method was used in two-step anodization process to make an AAO template with Y-type nanochannels. Then Y-type carbon nanotubes with controlled length and branch angle were prepared in the template based on chemical vapor decomposion (CVD) method with Co particles as catalyst and C₂H₂ as carbon source. The Y-type nanotube branches exhibit the angle distribution ranging from 20° to 120°. The results demonstrated that the oxidation potential should be responsible for the angles and length of the branches. Short pulse and high oxidation potential will result in the short and dense nanotube branches.

Study On The Gas Generation In Different Charging Voltage During Formation Process In Polymer Lithium-Ion Battery, Li Huang, Ming-Gang Jin, Hui-Qun Cai, Ming-Sen Zheng, Quan-Feng Dong, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

The gases of polymer lithium-ion battery (PLI) generated under different voltages during the first charging process were examined by means of gas chromatography (GC), and the mechanism of the gas generation was discussed. The electrolyte used in batteries was 1 mol/L LiPF₆-EC～DMC～EMC=1∶1∶1(in volume). The results showed that when the charging voltage is less than 2.5 V,  the main component of generated gases are H₂ and CO₂, and when the charging voltage is 2.5 V, EC begins to decompose. Due to the decomposition of EC, the main generated gas is C₂H₄ when the …

Application Of Hydrogen-Storage Alloy Electrode In Electrochemical Reduction Of Glucose, Hui Chen, You-Gen Tang, Zheng Tang

Journal of Electrochemistry

Electrolysis of glucose was performed at constant potential using hydrogen-storage alloy as catalytic reduction electrode. It was found that the superficial treatment and activation of hydrogen-storage alloy powder had obvious effects on improving the current efficiency of sorbitol. Under the optimums, current efficiency of sorbitol by electrolyzing glucose was over 94%. The yield of sorbitol was over 80%, the lifespan of electrode was tested and analyzed, the ways of regeneration were discussed.

The Study Of Green Corrosion Inhibitors For Mild Steel 907 In Natural Seawater Environment, Ping Gong, Min Du, Qing-Zhang Wang, Zhen-Jun Mu

Journal of Electrochemistry

Nine green compounds, including calcium gluconate, zinc gluconate, zinc sulfate, garlic, ACUSOL 445N, OS-15, APG, OCTA and STPP were selected according to the methods of molecule design and function groups prune. The functions of combined corrosion inhibitors mixed by the compounds mentioned above for mild steel in seawater were studied in this work using the methods of polarization curve and weight-loss.The best weight ratio and distinct synergistic effect of calcium gluconate, zinc sulfate and OCTA were studied by Latin experiment. The afgereffects of the best weight ratio corrosoin inhibitor were studied by subsection experiment. In this way, a kind of …

Pitting Characteristics Of Cu-50/60ni Alloys In Nacl Solution, Jie Li, Yan Niu, Shi-Zhe Song

Journal of Electrochemistry

The pitting behavior of nanocrystalline Cu-50/60Ni and cast Cu-50/60Ni alloys in different concentration of NaCl solutions has been investigated using various electrochemical methods. A logarithmic dependence of the passive breakdown potential (E_b), which is established using dynamic potential scan technic, on the chloride concentration was obtained for both alloys. The study on pitting propagation of both alloys was carried out using potential step chronocurrent method. As long as pits initiate on both alloys, the pits on nanocrystalline Cu-Ni alloys develop faster than those on cast alloys.

Preparation And Properties Of The Composite Microporous Pvdf-Hfp/Sio2 Based Polymer Electrolytes, Bao-Wen Zhang, Lu Qi, Hui Hen, Xiao-Hui Zhu, Li-Yan Liu, Yun-Xiang Ci

Journal of Electrochemistry

Microporous PVDF-HFP/SiO₂ film were prepared using a solvent/nonsolvent method-phase inversion method and the volatile plasticizers DMC, DEC or PC. The conductivity of the films increased pore volume measured by a nonsolvent uptake method. The conductivity of 1.86×10^-3 S⋅m^-1 were obtained using the liquid electrolyte LiPF₆(1 M) in EC/DMC (1:1).

Optimizing Catalyst Layer Composition Of Pemfc By Orthogonal Method, Ming-Hua Wang, Xin-Jian Zhu, Guang-Yi Cao, Sheng Sui, Qing-Chun Yu, Ming-Ruo Hu, Zheng-Yu Fan

Journal of Electrochemistry

The optimal composition of catalyst layer in a PEMFC electrode was studied through orthogonal method. It was showed that the performance of hydrophilic electrodes, in which there is no PTFE in the catalyst layer, were more favorable than that of hydrophobic electrodes. According to this condition, the power density of PEMFC attained 0.37 w·cm^-2 when the Nafion loading was 1.4 mg·cm^-2, and the Pt loading was 0.4 mg·cm^-2 in the catalyst layer, using H₂ as fuel and air as oxidant both at atmospheric pressure. Additionally, the results showed that increasing Pt loading in Pt/C catalyst …

The Study On Carbon Nanotube-Loaded Pt Catalysts For Proton Exchange Membrane Fuel Cells, Hong Zhu, Feng-Juan Ge, Xiao-Hong Kang, Yu-Guo Yang, Yun-Hua Xu

Journal of Electrochemistry

Carbon nanotube-supported-platinum (Pt/CNTs) and carbon-supported-platinum (Pt/C) catalysts were synthesized by in-situ chemical reduction. They were analyzed using TEM and XRD, then made into electrodes to be part of assemable PEMFC for the performence tests. The resulted show that Pt clusters in both catalysts are of small particle size (about 4nm), and Pt/CNTs exhibits a higher catalytic activity than Pt/C.

Effect Of Dspp Al2O3 On Electrical Properties Of Polymer Electrolyte, Hai-Fen Xie, Xiao-Xiang Sun, Yi-Pin Wang, Guang-Yuan Li

Journal of Electrochemistry

The PEO-NaSCN polymer solid electrolytes by adding dispersed second phase particles (DSPP) of Al₂O₃ were studied. The characteristics of solid electrolytes and conductivity values are dependent on DSPP Al₂O₃ sizes and its contents. It was found that when the Al₂O₃ sizes are less than 1 μm, which is a criticle size, the sample conductivities were larger than those of the pure PEO-NaSCN samples and when the Al₂O₃ sizes are larger than 1 μm then the sample conductivities are less then those of the pure samples. The maximum conductivity …

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge

Journal of Electrochemistry

Electrochemical oxidation of phenol was carried out by the Dimensionally Stable Anodes (DSA) electrode, which has been discarded as waste by alkali chloride factory. The result indicates that a good phenol removal can be obtained under certain phenol concentration by the DSA electrode. The key factor in effecting phenol removal of electrochemical oxidation is applied current density, the following factors are pH, electrolyte concentration and phenol concentration. After experiments, the optimal test conditions are 30 mA/cm², pH 10, electrolyte concentration 10 mg/L, phenol concentration 10 mg/L.67% CODcr removal and 90% absorbance removal are gained by electrochemical oxidation for …

The Current Fluctuations Of Carbon Steel In Nano2-Nacl Solutions, Yu-Ming Tang, Yu Zuo

Journal of Electrochemistry

The characteristics of current fluctuations of A3 carbon steel in NaNO₂-NaCl solutions were studied with potentiostatic and potentiodynamic polarization methods. The steel remained stable passivation in 0.1 mol/L NaNO₂ solution without Cl^-. After NaCl was added in to the solution, current fluctuations with a characteristic of quick increase and slow decrease occurred, indicating quick dissolution and slow re-passivation of the metastable pits. The metastable pitting may cause accumulated corrosion damage around certain area and result in observable pits. With the increase of chloride concentration, the occurring potential for metastable pits Em rised, and peak values …

Adsorption And Oxidation Of Phenol Electrode Processes, Bao-Cheng Wang, Yan-Ping Sun, Jin-Hua Zhu

Journal of Electrochemistry

The electrochemical behaviors of platinum electrode were studied by cyclic voltammetry in 1mol/L sulfuric acid solution and 1mol/L sulfuric acid solution contained phenol. The adsorption characteristics of phenol and the intermediat on electrode surface have been discussed. The reactive reversibility and oxidation mechanism of phenol on electrode process have been investigated.The potential of characteristic adsorption was suggested. The various products woud be formed when the electrode potential was greater than the one of characteristic adsorption.

Melanoma And Seborrheic Keratosis Differentiation Using Texture Features, Srinivas V. Deshabhoina, Scott E. Umbaugh, William V. Stoecker, Randy Hays Moss, Subhashini K. Srinivasan

Chemistry Faculty Research & Creative Works

Purpose: To explore texture features in two-dimensional images to differentiate seborrheic keratosis from melanoma.

Methods: A systematic approach to consistent classification of skin tumors is described. Texture features, based on the second-order histogram, were used to identify the features or a combination of features that could consistently differentiate a malignant skin tumor (melanoma) from a benign one (seborrheic keratosis). Two hundred and seventy-one skin tumor images were separated into training and test sets for accuracy and consistency. Automatic induction was applied to generate classification rules. Data analysis and modeling tools were used to gain further insight into the feature space. …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Quarterly Progress Report (June 1 – August 31, 2003), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

As indicated in the original proposal, the primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate target materials for applications in spallationneutron- target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including Alloy HT-9, Alloy EP 823 and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these materials are being evaluated in aqueous environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. …

Corrosion And Mass Transport Processes In Carbon Steel Miniature Waste Packages, James Cizdziel, Kaveh Zarrabi, Susan Lestrange, Amy J. Smiecinski

Publications (YM)

In this study, we have systematically investigated corrosion and mass transport processes in carbon steel miniature waste packages (MWP) in dynamic systems (water in, water out) under varying chemical conditions. The MWP were fabricated to have similar configuration to the DOE Spent Nuclear Fuel (SNF) waste package and that individual components to be in scale with each other compare to the SNF waste package. Two MWP configurations were studied: a "bathtub" model and a "flow-through" model. By slowly dripping 4 different solutions (groundwater obtained from well water J-13 located near Yucca Mountain, and J-13 water adjusted to low-pH, high-salinity, and …

Modeling And Control Of Vinyl Chloride In Drinking Water Distribution Systems, Michael Beardsley, Craig D. Adams

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In water distribution systems containing PVC pipe manufactured in the "early era" (prior to 1977), vinyl chloride can leach into drinking water resulting in vinyl chloride concentrations exceeding the 2 μg·L-1 maximum contaminant level. Field testing of dead-end segments of water distribution systems consisting of early-era PVC pipe was conducted to examine their initial intrapipe vinyl chloride monomer (VCM) concentrations based on a Fickian-diffusion-Based leaching model. the experiments showed a wide range of VCM concentrations within early-era PVC pipe ranging from less than 50 to more than 600 mg·kg-1. based on the diffusion modeling approach, a protocol was designed that …

Afci Quarterly Input – Unlv July Through September, 2003, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Fourth Quarterly Report 06/01/2003-08/30/2003, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Annual Report -Phase Ii 09/01/2002-08/30/2003, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Synthesis And Electrochemical Properties Of K2Feo4, Ning Zhou, Shi-Hai Ye, Yong-Long Wang, Xue-Ping Gao, Dong-Feng Lin, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The K₂FeO₄ used for new positive electrode materials was prepared. The primary batteries were used in different concentration of electrolyte and different currents. In 9 mol/L KOH , the capacity was the best. The higher the concentration of electrolyte, the lower the electric potential was. When the batteries discharged in 0.4 C , the capacity reached 521.3 mAh/g. By XRD, we gave the reasonable explanations for the discharge products of K₂FeO₄. Possible mechanism of discharge is discussed.

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou

Journal of Electrochemistry

A Mannich Base derivative (BMMCH), containing two morpholinum moieties and one cyclohexylamnonium moiety, was synthesized through aminomethy1 reaction. Its configuration was verified by IR and ¹H-NMR. Its volatile rustproofing effect was appraised by volatile rustproofing sieve test and vapor inhabitability test. The result shows that BMMCH has good protection effect for carbon steel. BMMCH has lower volatility compared with dicyclohexylamnonium nitrite (DICHAN) via closed space volatile weight-loss test. The inhibition mechanism was studied by potentiodynamic polarization electrochemistry technique in ASTM simulated atmospheric water. The corrosion potential of carbon steel electrode shifted to a negative direction when BMMCH was joined …

The Technique Of Rare-Earth Conversion Coatings On Aluminum Alloy, Jun-Tao Wang, Jian-Hua Wu, Guang-Zhang Chen

Journal of Electrochemistry

The orthogonal design was used to screen the film_forming technique on LY12 aluminum alloy using quadrivalent cerium salt, and the corrosion-resistance performance of the coating was studied. The results revealed that: after LY12 aluminum alloy was treated by cerium salt, its pitting potential shifts to positive direction while the corrosion potential slightly decreases, showing that the alloy becomes less sensitive to pitting corrosion was greatly improved, comparable to that after chromate treatment; in addition, by combining the results of electrochemical measurements with surface analysis, the mechanism of corrosion-resistance on the race-earth conversion coating of the aluminum alloy was also discussed.