Chemistry Commons^™

Improvement And Its Mechanism Of Storage Performance Of Ni-Mh Battery, Xiao-Feng Li, Li-Ping Ma, Yu-Wan Lou, Feng Li, Bao-Jia Xia

Journal of Electrochemistry

The storage performance of nickel-metal-hydride (Ni-MH) battery was studied by using galvanostatic charge-discharge and cyclic voltammetry. The experimental results indicated that CoOOH could not be completely restored after its being thoroughly reduced at lower potential, which might weaken electric conduction network in the positive electrode and result in fading of electrochemical properties of Ni-MH battery. Addition of nickel powder as a conductive agent into the positive electrode was beneficial to the capacity recovery after storage.

Preparation And Electrochemical Magnesium Insertion Behaviors Of Mgv2O6, Hua-Tang Yuan, Li-Fang Jiao, Jian-Sheng Cao, Xiu-Sheng Liu, Ming Zhao, Yong-Mei Wang

Journal of Electrochemistry

MgV₂O₆ was synthesized by conventional solid-state reaction from MgO and V₂O₅ as starting materials. X-Ray diffraction analysis showed that the prepared sample belongs to the monoclinic structure. Electrochemical magnesium insertion from aprotic electrolytes such as organomagnesium halides into this host was found possible and exhibited charge/discharge circulation.

Anodic Dissolution Of Aluminum In Koh-Ethanol Solutions, Hai-Bo Shao, Jian-Ming Wang, Xiao-Yan Wang, Yi Zheng, Jian-Qing Zhang

Journal of Electrochemistry

The feasibility of employing aluminum in KOH ethanol solution as a battery anode system was discussed. Weight loss measurement showed that the corrosion rate of Al is low enough to be used in sealed batteries. Through the measurements done by anodic polarization, EIS and galvanostatic discharge, it was found that Al is electrochemical active in a wide potential range in this system, and its discharge mechanism is similar to that of Al in aqueous solution. The discharge potential increased rapidly after a period of time, which might be caused by the discharge products depositing on the electrode surface.

Study On Mass Transport In Liquid Layer Adjacent To The Electrode Through Transmission Vop-Spectroellipsometry, Wei Zhu, Yu-Ru Yang, Zong-Qing Huang

Journal of Electrochemistry

In electrochemical system, the mass transport process in liquid layer adjacent to electrode is studied through theoretical analysis only.The diffusion process can be analyzed theoretically by Fick's law for homogeneous media. Up to now, none of satisfied experimental method has been reported for studying mass transport of a whole process in liquid media yet. This paper described the experimental approach to explore mass transport in electrochemical system by transmission Vop-spectroellipsometry briefly.

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma

Journal of Electrochemistry

The air electrodes with different mass ratio of Pt/active carbon or carbon nanotube as catalyst layer material have been prepared. The electrocatalytic performances for oxygen reduction were evaluated by means of polarization curve and electrochemical impedance spectroscopy (EIS). The results disclosed that carbon nanotubes dealt with nitric acid in the catalyst layer had been improved obviously on the electrocatalytic activity. After the surface of carbon nanotube was oxygenated and aggraded with platinum, the catalyst had obviously effects on the electrocatalytic activity. The air electrode with the mass ratio of active carbon to Pt/carbon nanotube in 4∶1 showed better electrocatalytic activity, …

The Investigation Of Bafesi/C Alloy Composite As Anode Materials For Li-Ion Battery, Rui-Xiang Feng, Hua Dong, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

A novel BaFeSi/C composite was prepared by mechanical ball milling, and lithium insertion reactions on the composite electrode were investigated by cyclic voltammetry , charge-discharge measurements, XRD and XPS spectroscopy. It is demonstrated that the capacity retention with indiscernible capacity decas during charge-discharge cycling. The improved cycling ability of the composite is suggested from a cooperative action by inactive FeSi₂ and BaSi₂ matrix and outer graphite shell, which both buffer the volumetric changes of the active Si phase and provide a good connection for electronic and ionic conduction during lithium insertion and extraction processes.

Electrochemical Investigations On Pitting Susceptibility Of Iron-Based Alloy, Wei-Shan Li, Hong-Yu Chen, Zhong-Zhi Yuan, Hong Li, Qi-Ming Huang, Dong-Sheng Lv

Journal of Electrochemistry

The formation process of passive film on iron and electronic properties and pitting susceptibility of an iron-based alloy are investigated by using linear potential sweep, alternative current impedance and electrochemical nose technologies. The relationship between reciprocal square capacitance and potential following the Mott-Schottky behavior is limited at a narrow rang of low potentials. At higher potentials, linear relationship between reciprocal capacitance and potential is obtained, which is ascribed to the increasing thickness of the passive film with potential. The donor density of the passive film is influenced by the formation potential of the film, passivator and microstructure. The decrease in …

LicoXNi1-XO2 Cathode Materials Prepared By Electrolysis Of Co And Ni, Jin-Ping Wei, Xin Sun, Xiao-Yu Wang, Xi-Kui Bian, Jin-Ling Zhai, Yan-Jie Yan-Jie

Journal of Electrochemistry

A new electrolytic method was developed to prepare LiCo_xNi_1-xO₂ as a cathode material of lithium-ion battery. Contrary to the traditional method, electrolytic method is a potential method with simple process to industrialization and no pollution. Metal cobalt and nickel were electrolysed in parallel to prepare the precursor of Co_xNi_{1- x}(OH)₂.Different compositional precursors could be conveniently prepared by changing electrolytic current. The LiCo_0.3Ni_0.7O₂ cathode prepared by this method was found favorable charge-discharge and cycle properties. For the LiCo_0.3Ni_0.7O₂ cathode material, …

Applications Of New Activated Carbon Meterials In The Electric Double-Layer Capacitor, Jian-Jun Zhang, Hua Jiang, Jian-Hui Fang, Li-Yi Shi, Ren-He Yin, Yi Wen, Ji-Quan Liu

Journal of Electrochemistry

A new type activated carbon whose precursor was coconut shell could be obtained using specific physics-chemistry activation, and the activated carbon was applied as the material of electrode in EDLC (electrical double-layer capacitor),which had a large specific capacitance, and could charge and discharged in some large currents. Carbon dioxide and acid were used to modify carbon,and the effects of post-treatment on surface area and pore volume were investigated. A moulding method which has influence on some properties of carbon electrode with PTFE additive was researched in the paper.

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe³⁺ dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe³⁺ dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

Additive-Assisted Cerium-Based Electrolytic Coating Process For Corrosion Protection Of Aluminum Alloys, James O. Stoffer, Thomas J. O'Keefe, Eric L. Morris, Scott Hayes, Paul Yu, Alex Williams, Xuan Lin

Chemistry Faculty Research & Creative Works

The corrosion resistance of an aluminum or aluminum alloy component is enhanced by immersing an aluminum alloy to act as a cathode and an oxygen-evolving anode in an electrolyte comprising water, cerium ions, and an additive selected from among animal gelatin, derivatives of animal gelatin, and amino acids, then passing an electrical current through the electrolyte to deposit a cerium-based coating onto the aluminum-based component.

Solvent And Method For Extraction Of Triglyceride Rich Oil, Shubhender Kapila, Paul Ki-Souk Nam, V. J. Flanigan

Chemistry Faculty Research & Creative Works

The present invention relates to a solvent for use in extracting oil from an oil bearing material, such as soybeans, with the solvent resulting in the selective extraction of a triglyceride rich oil, which contains 95% or greater triglycerides and non-polar constituents, with the solvent comprised of a hydrocarbon, preferably hexane, and a fluorocarbon, so that the solvent has a viscosity less than 2.6 centipoise and a polarity of less than 0.1. The present invention also relates to a method of using the solvent to extract the triglyceride rich oil, with the method including preferably extracting the oil at a …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Neutronic Evaluation Of Zro2-Mgo Inert Fuels, E. Fridman, A. Galperin, E. Shwageraus

Fuels Campaign (TRP)

Second task of the BGU part of “Dissolution, Reactor, and Environmental Behavior of ZrO₂-MgO Inert Fuel Matrix” project aims at evaluation of the fertile free fuel matrix composition effect on the fuel reactivity and corresponding reactivity limited burnup. Fertile free fuel with different MgO to ZrO₂ ratio in the matrix will require different PuO₂ loading in order to assure certain fuel cycle length. This is due to the fact that absorption cross section of Zr is slightly higher than that of Mg, although absorption in both of these elements is small compared to Pu. Therefore, the …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Final Report, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The whole chemical separation process is complex to the point that definitely requires certain level of systematic coordination. To perform smoothly and meet the target extraction rates among those processes, this research proposed a general-purpose systems engineering model.

A general purposed systems engineering model, Transmutation Research Program System Engineering Model Project (TRPSEMPro), was developed based on the above design concept. The system model includes four main parts: System Manager, Model Integration, Study Plan, and Solution Viewer. TRPSEMPro can apply not only to chemical separation process, but also a general system model.

Software engineering and Object Oriented Analysis and Design (OOA&D) …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The whole chemical separation process is complex to the point that definitely requires certain level of systematic coordination. To perform smoothly and meet the target extraction rates among those processes, this research proposed a general-purpose systems engineering model.

A general purposed systems engineering model, Transmutation Research Program System Engineering Model Project (TRPSEMPro), was developed based on the above design concept. The system model includes four main parts: System Manager, Model Integration, Study Plan, and Solution Viewer. System Manager supervises all the case (problem) creation, and functionality definition. Model Integration identifies chemical extraction processes and their execution sequence. Study Plan is …

Solvent And Method For Extraction Of Triglyceride Rich Oil, Shubhender Kapila, Paul Ki-Souk Nam, V. J. Flanigan

Chemistry Faculty Research & Creative Works

The present invention relates to a solvent for use in extracting oil from an oil bearing material, such as soybeans, with the solvent resulting in the selective extraction of a triglyceride rich oil, which contains 95% or greater triglycerides and non-polar constituents, with the solvent comprised of a hydrocarbon, preferably hexane, and a fluorocarbon, so that the solvent has a viscosity less than 2.6 centipoise and a polarity of less than 0.1. The present invention also relates to a method of using the solvent to extract the triglyceride rich oil, with the method including preferably extracting the oil at a …

Afci Quarterly Input – Unlv July Through September, 2004, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Neutronic Evaluation Of Zro2-Mgo Inert Fuels, E. Fridman, A. Galperin, E. Shwageraus

Fuels Campaign (TRP)

This progress report presents results of analysis performed within the framework of “Dissolution, Reactor, and Environmental Behavior of ZrO₂-MgO Inert Fuel Matrix” project managed by University of Nevada at Las Vegas, Harry Reid Center for Environmental Studies.

The BGU working program includes the following four tasks:

1. Benchmark of computational tools

2. Determination of fissile Pu loading

3. Evaluation of burnable poison designs

4. Evaluation of reactivity feedback coefficients

This progress report presents the results of Task 1. The main objective of this task is to confirm the validity of the ELCOS ¹ code system for inert matrix …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Trp Final Report 09/01/2003-08/31/2004, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Fourth Quarterly Report 06/01/2004-08/31/2004, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Chemical Microetching Of Three-Dimensional Gear-Like Pattern On Nickel Surface, Zhu-Fang Liu, Li-Ming Jiang, Jing Tang, Li Zhang, Zhong-Qun Tian, Zhao-Wu Tian, Pin-Kuan Liu, Li-Ning Sun

Journal of Electrochemistry

The chemical micromachining on nickel surface with three-dimensional (3D) gear-like mold was realized by confined etchant layer technique (CELT). By using effective chemical etching and scavenging system (HNO₃ +NaOH) and optimizing experimental parameters, such as the etching time, etching current density, concentration of the etchant or and scavenger, we obtained the etched pattern, which is close to negative copy of the mold. The etched micro-pattern characterized by SEM and AFM, demonstrates that CELT can be applied to the 3-D microstructure replication on nickel surface.

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang

Journal of Electrochemistry

New composite seperators for lithium ion batteries were prepared by coating PEO mixed with nanosize SiO₂ onto microporous polypropylene(PP) seperators. Highly conductive electrolytes were prepared by soaking them in an electrolyte solution. With these composite separators, the lithium ion cell consisting of Li anode and LiNi_0.8Co_0.2O₂ cathode were assembled. The high initial discharge capacity and good capacity retention were obtained through the cell.

Effects Of Barium On The Performance Of Secondary Alkaline Zinc Electrode, Yi Zheng, Jian-Ming Wang, Hua Chen, Hai-Bo Shao, Jian-Qing Zhang

Journal of Electrochemistry

The active material of secondary alkaline zinc electrode with barium additives was prepared by a chemical reaction method and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrochemical performance of various pasted Zn electrodes was investigated by cyclic voltammetry, charge/discharge method and electrochemical impedance spectra (EIS) technology. The addition of barium can synthesize a compound barium zincate with the molecular structure of BaZn(OH)₄·xH₂O and improve the discharge performance. The EIS of the various Zn electrodes showed two time constants besides diffusion impedance, including a state variable representing the covering degree of discharge products …

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO₂(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO₂(B) nanobelts electrode, and a high capacity (265 mAh·g^-1) can be obtained. The results suggested that TiO₂(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce_0.8Gd_0.2O_1.9 (CGO) and cathode materials of La_0.6Sr_0.4Co_0.2Fe_0.8O_3-α (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration …

Nucleation And Crystal Growth Of Pt Electrodeposition On Poly Crystal Au Microdisc Electrode, Zhi-Yong Tao, Pei-Fang Liu

Journal of Electrochemistry

Based on the Fleischmann's model of nucleation and crystal growth for electrodeposition combined with the Barradas-Bosco's adsorption-nucleation model for electrochemical phase formation, the chronoamperometry was well fitted for Pt deposition on polycrystalline Au micro disc electrodes (30 μm in diameter) in different H₂PtCl₆ concentrations at different over-potentials. The initial stage of Pt deposition in dilute H₂PtCl₆ could be interpreted by the model of H₂PtCl₆ adsorption combined with instantaneous nucleation and two-dimensional cylindrical growth. The rate constant of the two-dimensional growth increased linearly with overpotential. Then the deposit grew layer by layer …

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

The Electrochemical Behavior And Determination Of Gsh At The Powder Microelectrode, Jian Chen, Zhong-Yu He, Chuansin Cha, Huan Liu

Journal of Electrochemistry

In this paper, the electrochemical behavior of GSH at the surface of platinum(Pt) electrode, glass carbon(GC) electrode and acetylene black packed powder microelectrode (AB-PME) was studied. It was found that the electrochemical oxidations of GSH at both Pt and GC electrode were highly irreversible. No current peak or current plateau could be observed from the CV curves. The direct electro-oxidation of GSH at carbon surface was achieved by using the PME technique.In this case, the apparent reversibility of GSH oxidation was enhanced significatly .The overpotential of GSH oxidation was reduced to 0.5 V at the surface of AB-PME compared with …

Synergisms Of Electric Or Electromagnetic Fields And Photodynamic Effects Induce Apoptosis And Necrosis Of Cancer Cells, Radeva Maria, Lambrera Maya, Angelova Plamena, Traitcheva Nelly, Berg Hermann

Journal of Electrochemistry

Weak pulsating sinusoidal electromagnetic fields (PEMF) have been applied to change membrane permeation and induction of apoptosis (necrosis). In the case of suspension of human cancer cells U-937 and K-562 inside of Helmholtz-coils the amplitude of PEMF B=10 and at 39mT (at 50 Hz) was combined gradually with the cytotoxic agent actinomycin-C on one hand with its novel photodynamic activity on the other.

Studies On The Electrochemical Behavior Of Copper Paratolysulfate And Its Complexes, Ji-Guo Song, Pei-Kang Shen

Journal of Electrochemistry

Copper (II) paratolysulfate has been synthesized and characterized by thermo-gravimetric (TG) measurements and differential scanning calorimetric (DSC) analysis. This salt can easily lose all crystal water and the dehydrated salt does not deliquesce in the air. It is found for the first time that the complex of Cu(p-OTs)₂/ethanolamine(1∶1) can catalyze the oxidation of 1,1′-bi-2-naphthol in DMSO and DMF, while the process is difficult to perform in H₂O and CH₃OH. The electrochemical behaviors of both Cu(p-OTs)₂ and its complexes with ethanolamine have been studied on platinum electrode in DMSO, DMF, CH₃OH and …