Chemistry Commons^™

The Influence Of The Sputtering Power On The Structural And Electrochemical Properties Of Tin Oxide Films, Min-Zhen Cai, Jie Song, Ming-Sen Zheng, Qi-Hui Wu, Sun-Tao Wu, Quan-Feng Dong

Journal of Electrochemistry

Tin oxide films were deposited on silicon substrates at room temperature using the radio frequency(RF) magnetron sputtering with different sputtering power.The influence of sputtering power upon the crystal structure,surface morphology and electrochemical properties of tin oxide films were then investigated.The XRD and SEM results illustrate that the phase of tin oxide thin films changed from amorphous to crystalline and the grain size augments with the increase of the sputtering power.The constant current charge and discharge cycle tests imply that the initial irreversible capacity loss of Li/tin oxide batteries increase and which capacity decrease as the sputtering power increases.The sputtering power …

Effect Of Au At Different States On Electrocatalytic Performance Of Pd Catalyst For Oxidation Of Formic Acid, Xin Wang, Ya-Wen Tang, Tian-Hong Lu

Journal of Electrochemistry

Using liquid-reduction or complex-redution method,four catalysts,i.e,the Au/C,Pd/C,Pd-Au/C-T and Pd-Au/C-H were preparated and which electroanalytic activities and stabilities for the oxidation of formic acid were compares.It was found that the Au/C catalyst has no electrocatalytic activity,and the Pd/C catalyst possesses the good electrocatalytic performance for the oxidation of formic acid.The addition of Au into the Pd/C catalyst can increase the electrocatalytic activity and stability.Especially,the electrocatalytic activity and stability of the Pd-Au/C-T catalyst with the alloy of Pd and Au are better than that of the of the Pd-Au/C-H catalyst,in which,Pd and Au do not form the alloy.The investigation of its reason …

Molten Salt Treatment Of Mno2 And Investigation On Supercapacitor Properties, Ye Chen, Zun-Bo Zhang, Wei Zhang, Liang Liu, Zhi-Min Liu

Journal of Electrochemistry

The MnO₂ prepared by solid phase method is treated by KCl-NaCl-LiCl molten salt system.The XRD patterns indicated that the crystal structures of MnO₂ sample have had the α-MnO₂ and γ-MnO₂ phase,the crystallinity of sample is increased after treated by molten salt.The electrochemical properties were tested by cyclic voltammetry,constant current charge/discharge and AC impedance.The result shows that the supercapacitor performance of the treated material has improved.The specific discharge capacitance of the treated sample are 129.07 F·g^-1,increased by 27.88% compared to 100.94 F·g^-1 of untreated sample.Long cycle life and high coulombic efficiency were also demonstrated …

Synthesis Of 2,2′-Dichlorohydrazobenzene Using An Ion Exchange Membrane, Chao Zhang, Pei-Jin Li

Journal of Electrochemistry

Using an ion exchange membrane as a separator,the 2,2′-Dichlorohydrazobenzene is synthesized by the electrolytic reduction of o-chloronetrobenzene.The effects of electrode activation condition,current density,electrolyte temperature on electrolytic reduction are discussed.It was found that the optimum reaction temperature is 80 ℃.When the electrolyte concentration was 30% NaOH at the anode and 10% NaOH at the cathode,current density is 4.2A/dm²,the current efficiency reached 73% and yield is 83%.

Potentiometric Response Of Glucose On Mno2-GoX Carbon Paste Electrode, Cai-Juan Wang, Xiao-Ya Hu

Journal of Electrochemistry

A novel carbon paste electrode(CPE) modified with MnO₂ and glucose oxidase(GO_x), is reported. Different factors, such as the effect of supporting electrolyte, pH of solutions,various paste glues, the amount of MnO₂ and temperature, which may influence the determination of H₂O₂ and glucose were tested to optimize. Based on above, potentiometric determination of glucose was achieved in neutral solution and at 35 ℃, the electrode gave a response of 36.12～34.62 mV/pG lucose between 2.0×10^-5 mol·L-1 and 5.2×10^-3 mol·L^-1 with a detection limit of 3.3×10^-6 mol·L^-1. Moreover, this kind …

Square Wave Stripping Voltammetric Behaviors Of Rutin On Glassy Carbon Electrode And Its Application, Jun Hua, Xiao-Ying He, Fang Liao, Qing-Tao Zhu

Journal of Electrochemistry

The electrochemical behaviors of rutin(Rt) at glassy carbon electrode were studied by square wave stripping voltammeter in the presence of 0.1mol·L^-1HAc-NaAc buffer solution(pH=3.0).The sensitive oxidation peak of rutin was observed and which potential peak is 0.46V(vs.SCE).The experimental parameters,such as pH value,deposition potential and deposition time were investigated and selected.The peak currents were proportional to the concentration of rutin in range of 5.0×10^-8 mol·L^-1~1.0×10^-6mol·L^-1,and the linear regression coefficient equaled 0.99799,the detection limit was 1.1×10-8 mol·L^-1.This method was applied to the determination of rutin content in tablet with satisfactory results.

Corrosion Electrochemical Behavior Of Az31 And Az61 Magnesium Alloys In Simulated Sea Water, Ling-Jie Li, Sheng-Hai Yu, Jing-Lei Lei, Chuan-Pu Liu, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Tafel polarization curves and electrochemical impedance spectroscopy(EIS) techniques were employed to investigate the corrosion electrochemical behavior of AZ31 and AZ61 magnesium alloys.Scanning electron microscopy(SEM) was used to observe the alloy microstructure and corrosion morphology.The variation of the bulk corrosive medium pH with immersion time was recorded during the exposure of the alloys to simulated sea water.Results show that AZ61 magnesium alloy exhibits much better anti-corrosion ability than AZ31 magnesium alloy.The different corrosion behavior between the two magnesium alloys is correlated with their different content of Al alloying element.The higher content of Al in AZ61 alloy leads to the homogenerous microstructure …

The Determination Of Vitamin C By Bromophenol Blue Modified Glassy Carbon Electrode, Shu-Lin Zhang, Min-Jiao Li, Yi Luo, Xiao-Bo Wang

Journal of Electrochemistry

The content of ascorbic acid of(vitamin C) was analyzed by using fast cyclic voltamment with bromophenol blue(BPB) modififed GC-electrode,and which experimental conditions were optimiged.The results showed that the BPB modified GC-electrode had the good stability and anti-jamming faculty for analysing the content of ascorbic acid.A linear relationship between the peak current and concentration of vitamin C in the range of 0.0050~0.1500 g·L^-1 was obtained,which related coefficient and the detection limit are-0.9991 and 0.0010 g·L^-1,respeclively.The method has satisfactory results.

Evaluation Of Cs/Sr Waste Form For Long Term Storage And Disposal, Gary Cerefice

Waste Forms Campaign (TRP)

The goal of this project is to examine the potential long term performance of the proposed aluminosilicate waste/storage form for the isolation and eventual direct disposal of the cesium and strontium separated from recycled nuclear fuel. In the first phase of this work, researchers will investigate the sintering procedure to prepare the drum-like aluminosilicate waste/storage form from the as-received aluminosilicate powder, and then examine the basic physical properties, phase structure and microstructure of the sintered aluminosilicate with /without mixing solution with several ppm Cs/Sr. In the second phase, researchers will evaluate the interaction of the proposed waste form with structural …

Modeling The Physical Properties Of A Homologous Series On The Melting Temperatures And Densities Of N-Alkanes And Their Simple Alkyl-Derivatives, Antun Rubčić, Jasna Rubčić, James Chickos

Chemistry & Biochemistry Faculty Works

No abstract provided.

Polyaniline Nanofiber-Based Gas Sensors, Zhe-Fei Li, Frank D. Blum, Massimo F. Bertino, Chang-Soo Kim

Chemistry Faculty Research & Creative Works

There has been recent interest in conducting polymers that have very promising chemical and electrical applications. Some of these polymers have shown great potential for use in sensors.1 Polyaniline is one particular example of a prospective material. In our laboratory, we have studied the synthesis of polyaniline nanofibers. We have carried out one-pot syntheses to obtain polyaniline nanofibers in aqueous solutions where the polymerization was influenced by γ-radiation2 or UV-radiation.3 This polymer can also be patterned with an appropriate photo mask. In our present report, polyaniline nanofiber thin film sensors have been fabricated in one step by employing UV-irradiation and …

Thermal Analysis Of Adsorbed Poly(Vinyl Acetate) On Silica, Boonta Hetayothin, Frank D. Blum

Chemistry Faculty Research & Creative Works

The physical properties of polymers at interfaces can be quite different from those in bulk due to the interaction between the absorbed polymer and the surface. This phenomenon can be probed through the dynamic behavior of the polymer chains at the interface which can be experimentally probed by techniques such as nuclear magnetic resonance spectroscopy (NMR),1 viscoelasticity, and calorimetry. At the polymer-air interface, polymer chains have more flexibility than those at the polymer-substrate interface. On the other hand, at the silica-polymer interface, where chains are more restricted on the surface, a higher glass transition temperature (Tg) results as compared with …

Dynamics Of Adsorbed Pma-D₃ - Effect Of Substrate, Frank D. Blum, Burak Metin, Macduff O. Okuom

Chemistry Faculty Research & Creative Works

In the last few years, our group has focused much of our attention on studying the dynamics of polymers adsorbed at interfaces. Much of our work, to date has been on labeled poly(vinyl acetate)-d3 (PVAc-d3)1 and poly(methyl acrylate)-d3 (PMA-d3)2 on silica. We have been able to probe the effects of adsorbed amount,3 molecular mass,4,5 and the effect of overlayer.6 These studies have provided a view of the adsorbed polymer consistent with a motional gradient in the layer with the more mobile segments being those at the air-polymer interface and the less-mobile segments at the substratepolymer interface. However, we have not …

Glass Transition Behavior Of Poly(Methyl Acrylate) End-Grafted By Atrp To Amorphous Silica, Manikantan B. Nair, Frank D. Blum

Chemistry Faculty Research & Creative Works

Ultra-thin polymer films attached to solid substrates (supported films) have attracted significant interest in recent years. Supported films are used in the design of advanced materials like photoresists, lubricants and other electronic devices. Glass transition temperatures (Tgs) of supported polymer films have also been of significant interest. The Tg has been shown to depend on the thickness of the polymer film on the surface and the inherent nature of the surface. The effect of end-grafting of a polymer chain to a surface, on the Tg of the polymer has been studied previously.1 Reports on the study of glass transition behaviors …

Modeling The Fate Of Pharmaceuticals And Personal Care Products In Sewage Treatment Plants, Craig D. Adams

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Chemical fate models can be used to estimate the transformation reactions and the partitioning behavior of pharmaceuticals and personal care products (PPCPs) in sewage treatment plants (STPs). Modeling the fate of PPCPs in a STP requires parameters such as rate constants or partition coefficients that are often unique to a specific STP, and that may exhibit significant temporal variability. Chemical fate models provide both a valuable test of our understanding of the fundamental underlying mechanisms regarding the fate of PPCPs in STPs, as well as a means of providing both qualitative and quantitative estimates for PPCP removal. This paper is …

Dynamics Of Pipa-D₇ On Silica Surface, Piyawan Krisanangkura, Frank D. Blum

Chemistry Faculty Research & Creative Works

Molecular motion of polymer chains is an important determinant in understanding the physical properties of polymeric materials. Glass transition temperature (Tg) is a physical property of polymers, which is of primary interest. The study of the dynamics of polymer segments assists in understanding the dependence of Tg on polymer structure.1 For decades, studies have addressed the molecular motion in various polymers. Some of them have probed the dynamics of polymer backbones.2,3 the properties of a polymer at an interface may change because of the type of polymer, the substrate, or other variables. The side chain of a polymer can also …

Emulsification And Dispersant Properties Of Sugar Ester Glycolipid In Water In Oil And Oil In Water Emulsion., Azrah Abdul Aziz

Student Works (2010-2019)

The influence of different dispersing agent on the rheological behaviors of paraffin oil-water emulsion with addition of TiO2 for uv-protect and moisturizing active ingredient was studied. While making creams with minimal structural defects and longer storage stability, it is important that preparation conditions be optimized. Settle volume properties, Zeta potential, effective diameter and settle volume of TiO2 suspension were studied in the presence of glycolipid (DDM and Carrageenan), nonionic (PEG 10,000 and Brij 35P) as well as anionic surfactants (sodium dodecyl sulfate, SDS). In the experiments, the higher concentration of dispersing agents shows higher settle volume percentage, higher zeta potential …

Activation Energy Of Surface Diffusion And Terrace Width Dynamics During The Growth Of In (4×3) On Si (100) - (2×1) By Femtosecond Pulsed Laser Deposition, M. A. Hafez, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The nucleation and growth of indium on a vicinal Si (100) - (2×1) surface at high temperature by femtosecond pulsed laser deposition was investigated by in situ reflection high energy electron diffraction (RHEED). RHEED intensity relaxation was observed for the first ∼2 ML during the growth of In (4×3) by step flow. From the temperature dependence of the rate of relaxation, an activation energy of 1.4±0.2 eV of surface diffusion was determined. The results indicate that indium small clusters diffused to terrace step edges with a diffusion frequency constant of (1.0±0.1) × 10¹¹ s^-1. The RHEED specular …

A Study Of The Interaction Of Thioindigo Dye, With Several Inorganic Host Materials, Alejandra Ramirez

Open Access Theses & Dissertations

Maya Blue has been the focus of numerous studies and is believed to be a mixture of palygorskite clay and indigo dye.^1,2 Several derivatives of this pigment have been developed with intriguing properties. For instance, the dye thioindigo reacts with the palygorskite clay to exhibit a broad range of colors from red to blue under UV-Vis excitation. Based on FT-Raman and computer simulation, previous work performed in our group could relate indigo and thioindigo interaction to the aluminum sites in the framework. super>3,4

The work performed with other inorganic host materials such as, layer structures and zeolites have …

Oligo(Vinylidene Fluoride) Langmuir-Blodgett Films Studied By Spectroscopic, Rafal Korlacki, J. Travis Johnston, Jihee Kim, Stephen Ducharme, Daniel W. Thompson, Vladimir M. Fridkin, Zhongxin Ge, James M. Takacs

Stephen Ducharme Publications

Thin films of amphiphilic vinylidene fluoride oligomers prepared by Langmuir–Blodgett deposition on silicone substrates were investigated by comparing experimental and theoretical mid-infrared (IR) spectra. The experimental spectra were obtained using infrared spectroscopic ellipsometry. Theoretical spectra were calculated using density functional theory. Excellent correspondence of major IR bands in both data sets shows that the molecular backbone is oriented with the long axis normal to the substrate plane. This is in contrast to poly vinylidene fluoride[1] LB films, in which the polymer chains are parallel to the substrate.

University Of Nevada, Las Vegas Transmutation Research Program Annual Progress Report Academic Year 2007-2008, Anthony Hechanova, Rebecca Paulson

Transmutation Research Program Reports (TRP)

It is my pleasure to present the UNLV Transmutation Research Program’s seventh annual report that highlights the academic year 2007-2008. Supporting this document are the many technical reports and theses that have been generated over the past seven years.

In the seventh year of our program, we continued to see growth in the Radiochemistry Ph.D. program with a total of 20 students in the fourth year of the program (we anticipated twelve in the program proposal). Since our inception, the program has sponsored to their conclusion 48 M.S. and 6 Ph.D. degrees. The program supported 53 graduate students, 11 undergraduates, …

Separation Of Technetium From Uranium And Waste Form Synthesis, Kenneth Czerwinski

Waste Forms Campaign (TRP)

In this project, systematic investigations on the Tc-Zr binary metal system will be evaluated for the first time. The synthesis of metallic Tc as well as its alloys with Zr will be evaluated. In order to provide valuable data to AFC R&D, the thermodynamic equilibrium phases, as well as their performance under repository conditions, will be examined.

The research objectives of this project are as follows:

• Evaluate anion exchange methods for achieving the separation of Tc from U.

• Synthesize metallic Tc from the separated product.

• Synthesize and characterize Tc alloys.

• Investigate Tc-corrosion and Tc-leaching of binary …

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

This project focuses on the chemical bonding and interface formation of metal fission products with the coating materials used in tri-isotropic (TRISO) fuel particles for gas-cooled reactors. By combining surface- and bulk-sensitive spectroscopic and microscopic methods, intermediate chemical phases at the interface, intermixing/diffusion behavior, and the electronic interface structure for different coating materials and metals are examined.

In detail, the project studies the interface formation of Pd, Cs, and Ag with SiC and pyrolytic carbon. Using SiC single crystals and highly-ordered pyrolytic carbon (HOPG) as substrates, interfaces are prepared under controlled conditions in an ultra-high vacuum environment and are studied …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …

Impact Of The Synthesis Process On Structure Properties For Afci Fuel Candidates, Kenneth Czerwinski

Fuels Campaign (TRP)

The research objectives are:

• To explore a low-temperature fluoride route to synthesize actinide nitrides. • To characterize actinide nitrides structurally and thermally.

• To use high resolution TEM techniques to explore the microstructure of the radioactive samples.

Solution-Based Synthesis Of Nitride Fuels, Kenneth Czerwinski, Tyler A. Sullens

Fuels Campaign (TRP)

One of the original synthetic routes devised for the synthesis of U (III)N involved the entire reaction taking place in liquid ammonia. Several experimental reactions were conducted in an attempt to synthesize the UI₃(NH₃)_x and U(NH₂)₃(NH₃)_x precursors of U(III) N. Each attempt involved cleaning of the uranium metal to remove the oxide coating of the metal reagent with 3 washes of concentrated nitric acid, each followed by a rinse with liquid ammonia. Success of this cleaning procedure was varied, with a majority of cleaned metal oxidizing rapidly once …

Improved High-Temperature Stability And Sun-Light-Driven Photocatalytic Activity Of Sulfur-Doped Anatase Tio2, Suresh Pillai, Declan Mccormack, Pradeepan Periyat, John Colreavy, Steve Hinder

Articles

No abstract provided.

Electrochemical Oxidization Of Herring Sperm Dna And Its Interaction With Histone, Juan Xu, Gui-Ping Huang, Hong Li, Wei Zhu

Journal of Electrochemistry

The voltammetric behavior of herring sperm DNA at glassy carbon electrode and its interaction with histone have been investigated by using cyclic voltammetry,differential pulse voltammetry,and fluorescence measurement.In the potential range of 0.20 V to 1.25 V,it is found that an irreversible oxidative peak is exhibited in acid solution,but in the neutral or alkaline solution two oxidative peaks are observed.Oxidative peak potential values show a negative shift with increasing pH via a slope of-57 mV·pH-1 and a linear relation with DNA concentration in the range of 0.45 to 8.20 mmol·L^-1.In the presence of histone,the oxidative peak current of DNA …

Eiectro-Oxidation Of Methanol On Pdnio/C Catalyst In Alkaline Medium, Mei-Li Wang, Lin Sang, Cheng-De Huang

Journal of Electrochemistry

The electro-oxidation of methanol in alkaline electrolyte at in-house synthesized PdNiO/C and Pd/C catalysts and the effect of heat treatment on the structure and performance of catalysts were studied by cyclic voltammetry,chronoamperometry,chronopotentiometry and X-ray diffraction methods.It is shown that when the reduction temperature is 70℃ and the ratio between Pd and Ni is 8∶2,The PdNiO/C catalyst presents a highest activity for methanol electrooxidation.Calcining can increase the particle size and crystallinity of catalysts,but decrease the dispersion and activity of catalysts, too.Besides,the NiO is disengaged from Pd lattice by heat-treatment.The optimal PdNiO/C catalyst shows higher catalytic activity and much better poisoning resistance …

Preparation And Properties Of High Capacity Lifepo4, Jun Li, Gui-Tang Lai, Hui-Min Huang, Da-Guang Li, Xin-De Xia

Journal of Electrochemistry

Carbon-doped LiFePO₄/C and pure phase LiFePO₄ cathode materials were prepared by liquid-state precipitation reaction. The results of XRD, SEM, elemental analysis,FTIR and A.C.impedance tests show that the samples have had olivine structure and a 3.4V discharge platform.The tapped density of LiFePO₄/C sample could reach 1.46g/cm³, the initiate discharge capacity is 144.6mAh/g at 0.1C,which remained capacity is 93.2% after 20 cycles. The first discharge capacity is 133.5mAh/g at 1C and the capacity decreased 8.76% after 20 cycles.