Chemistry Commons^™

Synthesis Of High-Performance Lini1/3Co1/3Mn1/3O2 Cathode Materials Via Azeotropic Distillation Method, Sheng-An Xia, Li-Xia Yuan, Ze Yang, Zhao-Hui Wang, Yun-Hui Huang, Shuang Li, Wu-Xing Zhang, Ya-Bin Meng, Wei-Gong Zheng

Journal of Electrochemistry

Layered LiNi_1/3Co_1/3Mn_1/3O₂ is one of the most promising alternative materials for LiCoO₂ in lithium ion batteries due to its low cost,large capacity and excellent cyclability.In this paper,LiNi_1/3Co_1/3Mn_1/3O₂ was synthesized via azeotropic distillation method with isobutyl alcohol as an azeotropic agent.The structure and surface morphology were characterized by X-ray diffraction(XRD) and scanning electron microscope(SEM),respectively.The as-prepared LiNi_1/3Co_1/3Mn_1/3O₂ shows a layered α-NaFeO₂ structure;the particles are small and uniformly distributed.As compared with the sample prepared by traditional method,the present cathode material …

Electrochemical Behavior Of Co-Ru Composite In Alkaline Solution, Su-Mei Yao, Guo-Chun Li, Xue-Ping Gao

Journal of Electrochemistry

The electrochemical properties of Ru doped cobalt hydroxides synthesized via homogeneous chemical co-precipitation were investigated in 6 mol·L^-1 KOH solution by galvanostatic charge-discharge process and cyclic voltammetry(CV).It is demonstrated that Ru doped cobalt hydroxides exhibited good capacitive characteristic and high specific capacitance.The sample with a Co/Ru molar ratio of 8 /1 shows the optimized electrochemical performance,including capacitive property and discharge capacity.The microstructure and morphology of the obtained Ru doped hydroxides were characterized by X-ray diffraction(XRD) and scanning electron microscope(SEM).The amorphous structure of ruthenium dioxide nanoparticles and single-crystal structure of Co(OH)₂ platelets were confirmed.Based on a structure analysis and …

Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode, Lan-Qiang Li, Shi-Gang Dong, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

A single-dimensional array electrode was developed as a new electrochemical technique to image corrosion potential,galvanic current and polarization curves of reinforcing steel in concrete during corrosion process.Combining with the polarization behavior for each micro-electrode,the interactions between corrosion macrocell and corrosion microcell of the steel in concrete were evaluated.It was noticed that the corrosion macrocell and microcell occurred independently in difference regions at the initial stage of corrosion.The corrosion macrocell current can be in situ followed by corrosion potential imaging.The corrosion propagation of steel in concrete is closely related to the interactions between corrosion macrocell and corrosion microcell.

The Electrochemical Characteristics Of Cpo-Pll/Gc Electrode, Wen Zhao, Xia-Qin Wu, Zhong-Qing Lu, Wen-Jing Hou, He-Xing Li

Journal of Electrochemistry

Poly-L-lysine(PLL) was electropolymerized onto the surface of glassy carbon(GC) electrode.1[(3-dimethylamino)propyl]-3-ethylcarbodiimide hydrochloride(EDC) was used as a Cross-linking agent to immobilized Chloroperoxidase(CPO) onto the PLL/GC electrode.A pair of well-defined redox peaks was observed at CPO-PLL/GC electrode,which clearly suggested that PLL can promote the direct electron transfer between the CPO and the GC electrodes.The cyclic voltammetry results also showed that the electron transfer at CPO-PLL/GC is a surface adsorption-controlled quasi-reversible process,which is accompanied with proton transfer.The CPO-PLL/GC electrode exhibited a good electrochemical stability and excellently electrocatalytic activity for electrochemical reduction of O₂.

Electrosynthesis Of P-Aminobenzenearsenic Acid, Chun-An Ma, Qin-An Zheng, Qiang Zhou, Ying-Hua Xu

Journal of Electrochemistry

The electrochemical reduction of p-nitrophenyl arsonit acid to p-aminobenzenearsenic acid was studied using controlled-current electrolysis.The results showed that the yield of p-aminobenzenearsenic acid was determinated by the following factors:the concentrations of sulphuric acid,the amount of additive,temperature and the concentrations of p-nitrophenyl arsenic acid.The optimum electrolytic conditions were obtained to be is 10% H₂SO₄,1% NaCl,80 ℃,25 g/350 mL p-nitrophenyl arsenic acid and 10 A·dm^-2.The yield of arsanilic acid could be reached 64.7% under the optimum electrolytic conditions.

Electrochemical Corrosion Behavior Of Tio2/Ha Composite Coating On Medical Titanium In Tyrode's Physiological Solution, Li-Li Kong, Long-Xiang Lin, Rong-Gang Hu, Fan Zhang, Chang-Jian Lin

Journal of Electrochemistry

Titanium and its alloys have been widely used as medical implant materials because of their good mechanical properties and biocompatibility.However,the physiological corrosion of metal will release metal ions,resulting in toxic and side effects.In this paper,in order to improve the corrosion resistance of titanium,and to enhance its bioactivity and osseointegration,the surface modification of titamum were performed.Using eletrochemical methods Tafel polarization and electrochemical impedance spectroscopy(EIS) were applied to study the electrochemical corrosion behavior of TiO₂ /HA composite coating.It is indicated that the corrosion resistance of the prepared TiO₂ /Ti material in Tyrode's physiological solution is improved because of the enhanced …

Electrocatalytic Reduction Of L-Cystine At Pb/Nanotio2 Film Electrode, Dao-Bao Chu, Feng Wang, Ying Xiao, Xue-Jiao Zhang

Journal of Electrochemistry

The nanoporous Ti-based TiO₂ films electrodes modified with Pb particles(Pb/nanoTiO₂) were prepared by using anodization and potentiostatic electro-deposition.The optimum deposition conditions were determined by comparing with various deposition potentials and time.The SEM analyses indicated that the TiO₂ films were homogeneous nanoporous structure,and the Pb particles well dispersed on the TiO₂ films.The L-cystine electrocatalytic activity reduction on the Pb/nanoTiO₂ film electrodes was investigated by cyclic voltammetry and Chronoamperometric curves.The results showed that this type of the electrode posseses high acticity and stability.

Cobalt-Doped Todorokite Prepared By Refluxing At Atmospheric Pressure As Lithium-Ion Battery Cathode, Rui-Qi Li, Chun-Hua Song, Chao Xu, Li-Xing Tu, Guo-Hong Qiu, Fan Liu

Journal of Electrochemistry

Cobalt-doped todorokites were prepared by refluxing at atmospheric pressure,and then charactered by X-ray diffraction(XRD),thermogravimetry(TG) and the analysis of chemical compositions.These measurements showed that all of the refluxing products were single phase of todorokites and the structure formulas were Mg_xCo_yMnO_z·nH₂O,where 0.18 ≤ x ≤ 0.22,0 ≤ y ≤ 0.24,2.10 ≤ z ≤ 2.53,and 0.35 ≤ n ≤0.73.The electrochemical characteristics of cobalt-doped todorokites were examined as lithium insertion hosts for cathodes in rechargeable lithium batteries.The first discharge capacity of undoped todorokite electrode was 211 mAh/g and the discharge capacity became 37 mAh/g after 30 …

Study Of Electrodes Modified With Hybrid Copper Cobalt Hexacyanoferrate-Mwcnts Composites, Shan Jiang, Yun Zhang, Xiao-Yan Wang, Xiao-Fei Yao

Journal of Electrochemistry

The hybrid modified electrodes were obtained by electrochemical deposition of copper-cobalt hexacyanoferrate(CuCoHCF) /multi-walled carbon nanotubes(MWCNTs) on the surface of glassy carbon electrode.The effects of the amount of MWCNTs and composition of electrolyte on the properties of modified electrode had been researched.The copper cobalt hexacyanoferrate-MWCNTs modified electrodes show excellent electrochemical properties compared with that modified only copper-cobalt hexacyanoferrate.The CuCoHCF-MWCNTs/GCE exhibits obvious electrocatalytic activity towards oxidation of hydrogen peroxide.The oxidation peak current increased linearly with the concentration of hydrogen peroxide in the range of 3.16 × 10^-5 ～ 2.92 × 10^-3 mol· L^-1.The linear equation is given up …

Fabrication And Characterization Of The Ni-Scsz Composite Anodes With A Lscm-Ceo2 Catalyst Layer In Thin Film Sofc, Yun-Yun Wang, Bo Huang, Xin-Jian Zhu, Wan-Qi Hu, Qing-Chun Yu

Journal of Electrochemistry

Solid oxide full cell(SOFC) running directly on hydrocarbon fuels has attracted much attention in recent years. In this paper, a dual-layer structure anode was fabricated by tape casting and screen printing method. The addition of a LSCM-CeO₂ catalyst layer to the supported anode surface yielded better performance in ethanol fuel. The maximum power density reached 710 and 669 mW/cm² at 850 ℃ running on hydrogen gas steam and ethanol steam,respectively. No significant degradation in performance has been observed after 216 h of cell testing when the Ni-ScSZ13 anode was exposed to the ethanol steam at 700 ℃. Very …

Synthetic Levers Enabling Control Of Phase, Size And Morphology In Transition Metal Phosphide Nanoparticles (Fe, Ni), Elayaraja Muthuswamy

Wayne State University Dissertations

ABSTRACT

SYNTHETIC LEVERS ENABLING CONTROL OF PHASE, SIZE AND MORPHOLOGY IN TRANSITION METAL PHOSPHIDE NANOPARTICLES (FE, NI)

by

ELAYARAJA MUTHUSWAMY

May 2011

Advisor:Dr. Stephanie L. Brock

Major: Chemistry

Degree: Doctor of Philosophy

This dissertation study focuses on (1) development of a synthetic strategy to control phase in nanoscale iron phosphides; (2) extension of the developed phase control strategy to the nanoscale nickel phosphide system with simultaneous control on size and morphology and (3) illustration of the enhanced reactivity of nanoscale oxide systems.

A synthetic strategy to control phase in nanoscale iron phosphides was developed to prepare phase-pure samples of …

Design And Development Of Highly Active, Nanoengineered, Platinum Based Core-Shell Electrodes For Proton Exchange Membrane Fuel Cells, Seth Louis Knupp

Legacy Theses & Dissertations (2009 - 2024)

Highly active nanoengineered core-shell electrocatalyst have a great potential to be used as fuel cell electrodes. They can alleviate problems related with commercial carbon supported platinum by simultaneously lowering cost while enhancing reaction kinetics and overall performance. More recently, use of nanoengineered core-shell electrode structures have showed their ability to enhance the stability and overall lifetime of the catalyst without sacrificing the electrode's performance. We studied the potential of using highly active core-shell nanoparticles supported on carbon nanomaterials as fuel cell electrodes.

Characteristics Of Proton Conducting Pva-Chitosan Polymer Blend Electrolytes., Mohd Fakhrul Zamani Abdul Kadir

Student Works (2010-2019)

The main focus of this present work is to build a good conducting solid polymer electrolyte (SPE) based on chitosan and poly(vinyl alcohol)(PVA) blend. Solution cast technique has been employed to produce sample films in this work. From the scanning electron micrographs (SEM) the surface morphology of the blend containing 40 wt.% chitosan and 60 wt.% PVA (C4P6) is homogenous and miscible in one and another. The C4P6 film is the most amorphous and is the best candidate for the polymer host in the electrolyte systems studied in the present work. Ammonium Nitrate (NH4NO3) is the doping salt that provides …

Electrodeposition Of Tin Using Tin (Ii) Methanesulfonate From Mixture Of Ionic Liquid And Methane Sulfonic Acid., Yang Kok Kee

Student Works (2010-2019)

The electrodeposition of tin from Tin(II) Methane Sulfonate (MSA) with varying concentration in air and water stable 1-butyl-1-methyl-pyrrolidinium trifluoromethanesulfonate, (BMPOTF) ionic liquid at room temperature was studied. Cyclic Voltammetry served to characterize the electrochemical behavior of tin reduction and oxidation. The diffusion coefficient of stannous ions in the mixture of BMPOTF ionic liquid and MSA based electrolyte obtained via Randles-Sevcik and Cottrell equation was 2 × 10-7 cm2/s. Electroplating on copper panel was conducted under different current densities to determine BMPOTF based tin plating solution current efficiency. Mixture of BMPOTF and MSA based tin plating solution gave current efficiency as …

Synthesis Of Urethane Acrylate Macromer From Palm Oil-Based Polyol And Its Application As A Resin For Dental Composite., Fadhel A. A. Alsanabani

Student Works (2010-2019)

A slightly branched urethane acrylate macromer (UAM) was synthesized by reacting palm oil-based polyol with excess amounts of polymeric methylene diphenyl diisocyanate (MDI) to form urethane prepolymer, then reacted with 2-hydroxyethyl methacrylate (HEMA) and FT-IR spectroscopy confirmed the urethane and grafted acrylate groups. 0.2% by weight of camphoroquinone (CQ) and 0.8% by weight of ethyl-4-N,N-dimethylamino-benzoate (4EDMAB) by weight were added to render the experimental resins light-curable. Their viscosity, percentage of degree of conversion (%DC) and cross-linking density (CLD), percentage of volumetric polymerization shrinkage (%VPS), water sorption and solubility, flexural strength, modulus of elasticity and toughness were determined and compared to …

Synthesis And Characterization Of Zinc Oxide Nanostructures., Khalifa Said Zahran Al-Azri

Student Works (2010-2019)

The growth mechanism, morphology, structure and optical properties of the ZnO nanostructures grown on bare and gold-coated silicon substrates using carbothermal reaction at atmospheric pressure were investigated under different growth conditions. The ZnO nanostructures formed were studied as a function of substrate location, furnace temperature, Ar gas flow rate, deposition time and ZnO powder to carbon powder mass ratio. The morphology and structure of the samples were characterized using the fieldemission scanning electron microscopy (FESEM), energy dispersive x-ray spectroscopy(EDX) spectrum, x-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). It was found that in both silicon and gold-coated silicon …

Thermo-Electrical And Mechanical Studies On Polymer-Organically Modified Montmorillonite Composite., Norhana Abdul Halim

Student Works (2010-2019)

The field of polymer-nanoclay composite has attracted a lot of attention in materials studies due to the dramatic improvement on polymers characteristics. For example mechanical and thermal properties, chemical resistance as well as the reduced gas permeability. However, structural changes and the mechanisms that may contribute to these improvements are not fully understood. In this work, the study on polymer nanoclay composite concentrates on the effects of OMON inclusion within different polymer matrix systems. The matrixes are a series of natural rubbers (Standard Malaysia Rubber – Latex grade (SMRL); Deproteinized Natural Rubber (DPNR) and Epoxidized Natural Rubber (ENR-50)), plasticized Polyvinyl …

Electrical And Structural Studies Of Polyacrylonitrile (Pan) Complexed With Inorganic Salts., Khairul Bahiyah Md Isa

Student Works (2010-2019)

In the present study, polymer electrolyte films composed of polyacrylonitrile (PAN) as a host polymer, ethylene carbonate (EC) as the plasticizer and lithium triflate (LiCF3SO3) and sodium triflate (NaCF3SO3) as dopant salts were prepared by the solution cast technique. Five systems of polymer electrolytes films have been prepared; these systems are the plasticized-PAN system i.e. PAN-EC system, two salted-PAN systems i.e. PAN-LiCF3SO3 and PAN-NaCF3SO3, and two plasticized-salted PAN systems i.e. PAN-EC-LiCF3SO3 and PAN-EC-NaCF3SO3. The pure PAN film was prepared as a reference. The ionic conductivity for each system is characterized using impedance spectroscopy. The room temperature conductivity of the pure …

The Thermoluminescence Properties Of Manganese Doped Zns Nanophosphor., Khalid Humaid Zahir Al-Hinai

Student Works (2010-2019)

The thermoluminescence (TL) properties of Manganese (Mn) doped ZnS nanophosphors were investigated after gamma irradiation at room temperature. The ZnS:Mn nanophosphors were prepared by chemical precipitation method by using Zinc sulfate, Sodium sulfide and Manganese sulfate. 1 mole, 2 moles and 3 moles of Manganese sulfate were used to have different concentrations of Mn in doped ZnS. The formation of the nanophosphors was characterized by high resolution scanning electron microscopy FESEM, XRD and EDX. The obtained products consist of particles with the dimension about 85–150nm. Comparison between ZnS nanophosphors and commercial ZnS powder glow curves was studied. It was observed …

Synthesis Of Chromium-Based Ziegler-Natta Catalysts And Thier Application In Ethylene Polymerization And Copolymerization., Wong Jun Xuan

Student Works (2010-2019)

Four chromium-based oxo-trinuclear carboxylate complexes were prepared by reacting Cr(NO3).9H2O with acetic acid and substituted carboxylic acids to produce [Cr3O(CH3COO)6.3H2O]NO3.7H2O,[Cr3O(ClCH2COO)6.3H2O]NO3.3H2O, [Cr3O(Cl2CHCOO)6.3H2O]NO3.H2O and [Cr3O(Cl3CCOO)6.3H2O]NO3.2H2O, which alysis (TGA).Chromium content in each complex was determined by titrimetry method and the result was in good agreement with that from TGA. Chromium(III)monochloroacetate complex[Cr3O(ClCH2COO)6.3H2O]NO3.3H2O in combination with diethylaluminium chloride formed heterogeneous catalyst system for ethylene polymerization and ethylene-propylene copolymerization. Both Al/Cr ratio and temperature influenced the catalytic activity. The maximum activity of ethylene polymerization was 1768 gPE/gCr/hr/atm, achieved by polymerizing ethylene at 29°C with Al/Cr ratio 30.8. Effect of chloro-substituent groups on carboxylic ligand was studied …

Synthesis And Characterization Of Silicon Oxide And Silicon Carbide Nanostructures., Majid Salim Mohammed Al-Ruqieshi

Student Works (2010-2019)

Silicon oxide nanostructures have attracted extensive interests in recent years due to their physical and optical properties. SiOx nanostructures are synthesized by catalytic and non-catalytic approaches. With catalytic approach, long and uniform amorphous silicon oxide nanowires, nanofibers (comet and tree like), nanocakes and nanocages were synthesized on Si substrate by carbothermal evaporation reactions of TiO2 at high temperature. The SiOx nanowires were about 13 nm to 243 nm in diameters and 194 nm to several microns in length and the nanofibres with diameter between 8 nm to 30 nm and around 50 nm to 2.5μm in length. The diameter and …

Production Of Multiwall Carbon Nanotube For Alcohol Sensor Application., Ebtehal Saleh Alshaqaq

Student Works (2010-2019)

Multiwall carbon nanotube/polyethylene oxide (PEO), multiwall carbon nanoube/polyvinyl alcohol(PVA) and multiwall carbon nanotube/ polyvinyl alcohol(PVA)/zinc oxide(ZnO) have been tested as chemical sensors and detailed study on the effect of different gas concentration and material properties on gas sensitivity is presented. Initial composites were prepared by a simple solution casting and characterized by x-ray diffraction for ZnO, Fourier transform infra-red spectroscopy (FTIR) and scanning electron microscopy (SEM) to demonstrate crystallite size of ZnO, the morphology and surface area respectively. On the other hand, MWCNT/PEO , MWCNT/PVA , MWCNT/PVA/ZnO were prepared with different loading MWCNT and ZnO. The chemical sensing properties of …

Electrodeposition Of Tin Using Tin(Ii) Methanesulfonate From Mixture Of Ionic Liquid And Methane Sulfonic Acid., Yang Kok Kee

Student Works (2010-2019)

The electrodeposition of tin from Tin(II) Methane Sulfonate (MSA) with varying concentration in air and water stable 1-butyl-1-methyl-pyrrolidinium trifluoromethanesulfonate, (BMPOTF) ionic liquid at room temperature was studied. Cyclic Voltammetry served to characterize the electrochemical behavior of tin reduction and oxidation. The diffusion coefficient of stannous ions in the mixture of BMPOTF ionic liquid and MSA based electrolyte obtained via Randles-Sevcik and Cottrell equation was 2 × 10-7 cm2/s. Electroplating on copper panel was conducted under different current densities to determine BMPOTF based tin plating solution current efficiency. Mixture of BMPOTF and MSA based tin plating solution gave current efficiency as …

Synthesis And Characterization Of Limpo[4] (M=Mn, Ni And Fe) Olivine Materials., Azlin Sanusi

Student Works (2010-2019)

Lithium transition metal phosphate, LiMPO4 compounds with olivine structure namely LiMnPO4, LiNiPO4 and LiFePO4 were successfully synthesized in the present work. LiMnPO4 and LiNiPO4 were synthesized by the sol-gel method with tartaric acid as the chelating agent. LiFePO4 was synthesized via the chemical precipitation and low temperature sterilizer heating method. TGA was carried out on LiMnPO4 and LiNiPO4 samples to determine the firing temperature of the gel precursor and the thermal stability of the prepared samples. LiMnPO4 was heated for 15 hours at various temperatures and LiNiPO4 was formed at 1000 oC with firing time of 24 hours. Firing of …

Hrc Enews — 2010 Winter, Megan K. Svarz

Publications (HRC)

This issue contains staff accomplishments and announcements, event listings, a "new faces" listing for new staff, affiliates, and researchers, and an "on the move" section listing new developments.

Investigating Fabrication Methods For Micro Single-Chamber Solid Oxide Fuel Cells, Man Yang

Dissertations

A Solid Oxide Fuel Cell (SOFC) is a green energy technology that offers a cleaner and efficient alternative to fossil fuels. The efficiency and utility of SOFCs can be enhanced by fabricating miniaturized component structures within the fuel cell footprint. This research focuses on the microfabrication of parallel-connected inter-digitized design of micro single chamber SOFC (µ-SC-SOFCs). In this dissertation, candidate micro/nano fabrication techniques to precisely fabricate micro patterns on planar substrates have been studied. These include EBL, soft lithography, photolithography, and direct-writing. After analyzing preliminary results, two combinational approaches were further investigated. The first method involves the combination of the …

Effluent Organic Nitrogen (Eon): Bioavailability And Photochemical And Salinity-Mediated Release, Deborah A. Bronk, Quinn N. Roberts, Marta P. Sanderson, Elizabeth A. Canuel, Patrick G. Hatcher, Rajaa Mesfioui, Katherine C. Filippino, Margaret R. Mulholland, Nancy G. Love

Chemistry & Biochemistry Faculty Publications

The goal of this study was to investigate three potential ways that the soluble organic nitrogen (N) fraction of wastewater treatment plant (WWTP) effluents, termed effluent organic N (EON), could contribute to coastal eutrophication - direct biological removal, photochemical release of labile compounds, and salinity-mediated release of ammonium (NH₄+). Effluents from two WWTPs were used in the experiments. For the bioassays, EON was added to water from four salinities (∼0 to 30) collected from the James River (VA) in August 2008, and then concentrations of N and phosphorus compounds were measured periodically over 48 h. Bioassay results, based …

Synthesis And Manufacture Of Photocrosslinkable Poly(Caprolactone)-Based 3d Scaffolds For Tissue Engineering Applications, Nathan Jonathan Castro

Open Access Theses & Dissertations

It is known that the body can efficiently repair hard tissue (bone) micro fractures by suturing the defect through the deposition of minerals resulting in an area that is stronger post-injury. Larger defects, however, generally cause more trouble since the body is incapable of repairing them. Bone defects can occur as a result of congenital abnormalities, trauma, or disease. Traditional methods for addressing these defects have involved the use of acellular cadaverous bone or autologous bone. Both contain innate problems associated with them; the former method can result in disease transmission, as well as very low integration with the host …

A New Green Chemistry Method Based On Plant Extracts To Synthesize Gold Nanoparticles, Milka Odemariz Montes Castillo

Open Access Theses & Dissertations

Extraordinary chemical and physical properties exhibited by nanomaterials, as compared to their bulk counterparts, have made the area of nanotechnology a growing realm in the past three decades. It is the nanoscale size (from 1 to 100 nm) and the morphologies of nanomaterials that provide several properties and applications not possible for the same material in the bulk. Magnetic and optical properties, as well as surface reactivity are highly dependent on the size and morphology of the nanomaterial. Diverse nanomaterials are being widely used in molecular diagnostics as well as in medicine, electronic and optical devices. Among the most studied …

Effect Of Cu Addition On The Conductivity Of Xcui-(1-X)Agi,(0.1 _ X _ 0.4) Solid Solutions., Chu Lee Peng

Student Works (2010-2019)

Silver Iodide (AgI) based superionic conductors continue to be investigated for their intriguing structure phase transformation and complex but useful ion dynamics. However, unlike the others alkali iodides, AgI does not easily admit impurities in its tetrabonded zincblende structure. Introduction of copper (I) iodide (CuI) into AgI lattice was expected to initiate and stabilize changes in structure of the cation sublattice which controls the phase stability and phase transition behavior. In the present work, silver rich xCuI-(1-x)AgI (0.1 ' x ' 0.4) have been prepared by sintering method. The mixtures were ground and pelletized before subjected to sintering temperature at …