Chemistry Commons^™

Electrocatalytic Oxidation Degradation Kinetics Of Oxalic Acid In A Cylindrical Electrochemical Reactor With Ti/Iro2-Ta2O5 Anode, Jing Su, Hai-Bo Lin, Hong Xu, Wei-Min Huang, Ya-Peng He

Journal of Electrochemistry

The electrocatalytic oxidation degradation kinetics of oxalic acid in a cylindrical electrochemical reactor with Ti/IrO₂-Ta₂O₅  as an anode was studied. The relation between instantaneous current efficiency and organic concentration in bulk was established based on the two paths for direct electrochemical oxidations, and the theoretical model was verified by experiments. The experimental resultswere reasonably consistent with the established kinetic model. Furthermore, the competition between the two paths was explored with the modelparameter analysis.

Performance Of The Electro-Oxidation And Electro-Fenton Processes With A Bdd Anode For The Treatment Of Low Contents Of Pharmaceuticals In A Real Water Matrix, Sirs Ignasi, Antonio Garrido Jos, Brillas Enric

Journal of Electrochemistry

Here, we report the performance of electro-oxidation and electro-Fenton with a boron-doped diamond (BDD) anode for the treatment of single and multicomponent solutions containing small amounts of pharmaceutical residues (i.e., 1 mg·L^-1 paracetamol and/or 1 mg·L^-1 salicylic acid) spiked into a real water matrix at pH 3.0. Electro-oxidation was performed in a BDD/Pt cell, whereas electro-Fenton was carried out in a BDD/air-diffusion cell to electrogenerate H₂O₂ at the cathode, always operating at constant current density. It was found that the decay of both pharmaceuticals by electro-oxidation was more rapid in the real water matrix than …

Electrochemical Behavior And Content Determination Of Paeonol At Poly Sudan Ⅲ Modified Electrode, Yan-Jie Zheng, Ai-Lin Liu, Yun Lei, Xin-Hua Lin

Journal of Electrochemistry

The poly SudanⅢ modified electrode was characterized by electrochemical impedance spectroscopy（EIS）and cyclic voltammetry (CV), while the electrochemical behavior of paeonol was studied by cyclic voltammetry (CV). The result shows that the poly Sudan Ⅲ modified electrode exhibits excellent electrocatalytic effect on the oxidation of paeonol. The peak currents of differential pulse voltammetry are linear to the paeonol concentrations over the range of 3.0*10^-7 ~ 2.2*10^-5 mol·L^-1. The detection limit has been estimated to be 5.0*10^-8 mol·L^-1. This method can be used for determination of paeonol content in real sample with satisfactory results.

Synthesis Of Platinum And Platinum-Copper Branched Nanoparticles For Electrooxidation Of Methanol, Eric Courtland Taylor

Graduate Theses and Dissertations

Platinum and Pt alloys are among the most important heterogeneous catalysts for many organic reactions and electrochemical reactions associated with the fuel cell technologies. How to reduce Pt usage while maintaining the performance of the catalysts becomes a subject for intensive research in materials chemistry. For heterogeneous catalysis, the catalytic reactivity and selectivity are strongly correlated with different crystallographic facets exposed on the surface. The facets with high-index planes whose Miller indices with at one is larger than unity are generally more active than those with low-index planes (e.g., {100}, {111}, and {110}). Tuning the morphology of the nanoparticles to …

Polysaccharide-Based Nanocarriers For Improved Drug Delivery, Nan Zhang

Dissertations - ALL

The field of drug delivery has provided a solution to the limited efficacy and high toxicity of many drugs. Nano-sized drug carriers are popular because their size allows for selective accumulation in the diseased area. Polysaccharides are non-toxic and biodegradable natural polymers that can serve as the basis for these nano-sized carriers. Polysialic acid (PSA) is such a polysaccharide with strong hydrophilicity that may reduce uptake by the reticuloendothelial system and prolong drug circulation. In this study, we developed PSA-based nanocarriers, specifically micelles and nanoparticles, for improved drug delivery with improved efficacy and minimized toxicity. PSA-based micelle systems were developed …

55th Annual Rocky Mountain Conference On Magnetic Resonance

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 55th annual meeting of the Rocky Mountain Conference on Magnetic Resonance, co-endorsed by the Colorado Section of the American Chemical Society and the Society for Applied Spectroscopy. Held in Denver, Colorado, July 28 - August 1, 2013.

Fe, Co And Ni Adatoms Adsorbed On Silicene: A Dft Study, Kent Gang '14, Siva Gangavarapu '14, Matthew Deng '14, Glenn W. "Max" Mcgee, Ron Hurlbut, Michael Lee Dao Kang, Sean Ng Peng Nam, Harman Johll, Tok Eng Soon

Student Publications & Research

Two-dimensional materials have attracted much research attention given their intriguing properties. The latest member of this class of materials is silicene. In this work, we investigate the adsorption of Fe, Co and Ni adatoms on silicene using plane-wave density functional theory calculations within the Perdew-Burke-Ernzerhof parameterization of the generalized gradient approximation for the exchange-correlation potential. In particular, we calculate the binding energy, magnetization, and projected electronic configurations of these adatoms adsorbed at different sites on the silicene. Our calculations show that the hole site (i.e. in the centre of a hexagonal-like arrangement of Si atoms) is the most stable configuration …

Improving The Stability Of High And Low Bandgap Polymers Organic Photovoltaic Devices Using A Solution Based Titanium Sub-Oxide Interfacial Layer, Kurniawan Foe

Electrical & Computer Engineering Theses & Dissertations

The improvement in device efficiency has brought organic photovoltaic (OPV) devices closer to commercial viability, highlighting the importance of studying the lifetime and stability of OPV devices. At present, the lifetime and stability of OPV devices is much shorter and poor mainly caused by oxygen, moisture, and light resulting in the oxidation on low work function electrodes and the degradation of the morphology of the photoactive layer. To improve the lifetime and stability of the OPV devices, we used newly developed low bandgap polymer, PCDTBT, as the electron acceptor material and a solution based titanium sub-oxide (TiOx) interfacial layer inserted …

Effect Of Ethyl Propionate On Low-Temperature Performance Of Lifepo4-Based Li-Ion Battery, Xiao-Ping Li, Lian-Sheng Hao, Wei-Shan Li, Meng-Qing Xu, Li-Dan Xing

Journal of Electrochemistry

A linear carboxylic, ester ethyl propionate (EP), was used as the co-solvent of carbonates, ethylene carbonate (EC), ethyl-methyl carbonate (EMC) and dimethyl carbonate (DMC), and its effect on low-temperature performance of LiFePO₄-based Li-ion battery was studied by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge-discharge test. The application of EP enhances the ionic conductivity of the electrolyte, improves the compatibility of the electrolyte with both LiFePO₄ and graphite materials, and thus improves the low-temperature performance of LiFePO₄-based Li-ion battery. The Li-ion battery using the optimized electrolyte of 1 mol·L^-1 LiPF₆/EC:EMC:DMC:EP …

Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution, Xiao-Juan Zhang, Jing-Jing Wang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The Zn-Al layered double hydroxides (Zn-Al LDHs) and calcined products (Zn-Al CLDHs) were synthesized successfully under a routine air atmosphere. The results showed that both Zn-Al LDHs and Zn-Al CLDHs had obvious flake structures. The corrosion inhibition of Zn-Al CLDHs for steel rebar in NaCl solution was studied by electrochemical techniques. It was found that the corrosion rate of steel rebar decreased significantly after the steel rebar was treated by Zn-Al CLDHs in NaCl solution for 3 h. It was indicated that Zn-Al CLDHs could absorb Cl^- and release OH^- during their reconstruction process, which provided dual protection …

Influences Of The Cinnamic Acid On Zinc Electrodeposition At Glassy-Carbon Electrode, Kai Li, Shen Chen, Shen-Na Liu, Bi-Sang Chen, Heng Lin, Guo-Liang Chen, Qing-Xiang Wang

Journal of Electrochemistry

The influences of cinnamic acid (CIN) on the mechanism of Zn deposition and nucleation kinetics onto glassy-carbon electrode were studied by cyclic voltammetry (CV) and chronoamperometry (CA). The results revealed that the zinc reduction took place via Zn²⁺ + 2e → Zn in the presence of CIN, but the kinetics of zinc deposition was changed and the formation rate of zinc nuclei was accelerated. In the absence of CIN, the mechanism of zinc nucleation followed the 3D-instantaneous diffusion-controlled nucleation, while the 3D-progressive diffusion-controlled nucleation in the presence of CIN. The addition of CIN reduced the nucleation rate, but increased …

Preparation And Characterization Of A Novel Composite Electrolyte Ceria-Sulfate For Intermediate Temperature Solid Oxide Fuel Cells, Ze Tong, Yi-Mei Yin, Jie-Wei Yin, Zi-Feng Ma

Journal of Electrochemistry

A novel composite electrolyte SDC-(Li/Na)₂SO₄ was prepared for intermediate temperature solid oxide fuel cells (ITSOFC). The phase structure and cross-sectional morphology were examined by XRD and SEM, respectively, and the ionic conductivity was investigated by AC impedance in a temperature range of 400 ^oC ~ 700 ^oC in air. It was found that the composite electrolyte was composed of two phases: crystal SDC and amorphous (Li/Na)₂SO₄. The conductivity of the composite electrolyte was significantly larger than that of SDC at intermediate temperatures (550 ^oC ~ 700 ^oC) and increased …

The Effect Of Precursors On Performance Of Lini0.5Co0.2Mn0.3O2 Cathode Material, Dong-Ge Hu, Zhang-Zhi Wang, Jia-Li Liu, Tao Huang, Ai-Shui Yu

Journal of Electrochemistry

Commercial LiNi_0.5Co_0.2Mn_0.3O₂ material is generally prepared by a combination of co-precipitation and solid state reaction method. The particle size distribution and morphology of Ni_0.5Co_0.2Mn_0.3(OH)₂ precursor have a great impact on the electrochemical performance of LiNi_0.5Co_0.2Mn_0.3O₂. In this work, the crystal structure and surface morphology of LiNi_0.5Co_0.2Mn_0.3O₂ prepared by three different precursors were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Particle size distribution, tap density and electrochemical performance were …

Preparation And Electrochemical Performance Of Hollow Carbon Spheres/Sulfur Composite, Jun Zang, Hang Qian, Er-Man Zeng, Juan-Ni Fu, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Hollow carbon spheres were prepared by the PMMA template. Hollow carbon spheres/sulfur composite was made from sulfur and hollow carbon spheres as a conducting framework. The results of SEM and TEM showed that sulfur was uniformly filled in both of the shell and hollow core of hollow carbon spheres. The electrochemical performance of hollow carbon spheres/sulfur composite was characterized by the charge/discharge method. The results showed the excellent rate and cycle performance of hollow carbon spheres/sulfur composite. The reversible capacities of hollow carbon spheres/sulfur composite are 1145 mAh·g^-1, 824 mAh·g^-1, 702 mAh·g^-1, 586 mAh·g …

Polypyrrole-Transition Metal-Oxygen Coordination Complexes As High Performance Lithium Storage Material, Ya Mao, Qingyu Kong, Bingkun Guo, Zhaoxiang Wang, Liquan Chen

Journal of Electrochemistry

No abstract provided.

Influence Of Electrode Hydrophobicity On Performance Of Alkaline Polymer Electrolyte Fuel Cells, Li-Sheng Tan, Jing Pan, Yao Li, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

In the present work, we study the influence of the electrode hydrophobicity on the performance of alkaline polymer electrolyte fuel cells (APEFCs). QAPS or xQAPS is employed as the membrane and the ionomer, while PTFE is used as a hydrophobic additive in order to adjust the electrode hydrophobicity. We find that enhancing the hydrophobicity of anode can promote the performance of APEFCs, while a moderate hydrophobicity of cathode is required to achieve optimal performance. By using xQAPS as the electrolyte and adding some PTFE in the anode, a peak power density of 132 mW·cm^-2 can be obtained at a …

Electrocatalytic Mechanism And Porous Electrode Mass Transfer Process In Membrane Electrode Assembly For Direct Methanol Fuel Cells, Xin-Dong Wang, Yi-Tuo Wang, Gui-Cheng Liu, Meng Wang, Zhe Tian

Journal of Electrochemistry

Direct methanol fuel cell (DMFC) is considered to be a promising commercial energy conversion device for portable electronics due to its many advantages. In order to improve the performance of DMFC, many companies and research institutes have been launching the deep research and obtaining a lot of conspicuous achievements. In this paper, the electrocatalytic mechanism and porous electrode mass transfer process in membrane electrode assembly (MEA) are analyzed. In addition, combined with the preparation process of MEA, multilayer ordered structures and internal transfer process of the cell, recent progresses of MEA in DMFC are discussed.

Electrochemical Nanofabrication Using Polyacrylamide Hydrogel As Soft Stamps, Wen Sun, Hai-Tao Fan, Da-Xiao Zhang, Dong-Jie Hu, Yong-Liang Zhou

Journal of Electrochemistry

The fabrication resolution of electrochemical wet stamping (E-WETS) was enhanced to several hundred nanometers from several ten micrometers by using polycarylamide gel (PAG) as soft stamps and through optimized processes. The PAG stamp was cured on a nanopatterned soft mold and soaked with 0.2 mol·L^-1 KCl solution, then contacted with a silicon wafer with gold film and applied with electric field. And the gold nanopatterns were achieved by the selective anodic dissolving, the diameter of fabricated gold spot was around 200 nm. The parameters which affected the fabrication processes have been discussed in detail.

Fabrication And Performance Of Lani0.6Fe0.4O3-δCathode Modified By Coating With Gd0.2Ce0.8O2 For Intermediate Temperature Solid Oxide Fuel Cell, Rui-Xuan Ren, Bo Huang, Xin-Jian Zhu, Yi-Xing Hu, Xiao-Yi Ding, Zong-Yao Liu, Ye-Bin Liu

Journal of Electrochemistry

The symmetric cell of LaNi_0.6Fe_0.4O_3-δ/Sc_0.1Zr_0.9O_1.95/LaNi_0.6Fe_0.4O _3-δ was fabricated with screen printing method. A LaNi_0.6Fe_0.4O_3-δ (LNF) cathode was modified by coating with nano-sized gadolinium-doped ceria (GDC, Gd_0.2Ce_0.8O₂) prepared using a simple combustion process within the pores of the cathode. According to the electrochemical impedance spectra (EIS), the polarization resistance of the pure LNF was 0.70 W·cm² at 750 ºC, while 0.13 W·cm² for the 21.3% GDC (by mass)-coated LNF cathode at the …

Optimization Of Electroless Silver Plating Process On Fabric Surface Without Activation And Sensitization, Bo Lian Wang, Ya Ping Zhao, Zai Sheng Cai

Journal of Electrochemistry

Silver was deposited homogeneously on the surface of polyamide fabric by electroless plating without activation and sensitization. The electroless silver plating process was optimized with the orthogonal array testing strategy. It is found that the optimum conditions are the electroless plating time of 50 min with the concentrations of silver nitrate, sodium hydroxide and ammonium hydroxide being 14 g·L^-1, 6 g·L-1 and 130 mL·L^-1, respectively. The surface morphologies, compositions, and phases of fabric samples were characterized by scanning electron microscopy and energy-dispersive X-ray spectrometry (SEM-EDS), X-ray diffraction (XRD). The wear-resisting property was tested by friction fastness …

Progress Of Lithium Rich Cathode Materials For Li-Ion Batteries, Jie Zhang, Jiu-Lin Wang, Jun Yang

Journal of Electrochemistry

Lithium rich materials xLi₂MnO₃·(1-x)LiMO₂ (0-1 and low cost. However, the large irreversible capacity during the first cycle, low rate capability and structure collapse during cycling remain impediments in developing these cathodes for applications. The structure analyses and charge/discharge mechanisms for lithium rich materials are currently main research contents. Although whether the lithium rich materials are solid solutions or composite is still controversial, oxygen release mechanism on the first charge 4.5 V plateau of lithium rich materials has come to consistency. Several modifications, such as bulk doping, surface coating and microstructure control, demonstrate promising strategies to …

Electrochemical Performance Of Al-Doped Spinel Limn2O4 Cathode Material For Li-Ion Batteries, Yong-Long Wang, Wen-Ge Wang, Qian Zhang, Xin Wang, Jian-Sheng Cao, Shi-Hai Ye

Journal of Electrochemistry

Spinel LiMn₂O₄, a cathode material for Li-ion batteries, is featured as good high-rate performance, low cost and environmental friendly. The pristine and Al-doped LiMn₂O₄ samples were prepared by sol-gel method. The structure and micromorphology of the as-prepared samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results demonstrated that the as-prepared LiMn₂O₄ samples had a typical cubic spinel structure and were composed of sphere-like particles with a diameter range of 300 ~ 500 nm. Galvanostatic charge-discharge tests showed that the LiMn₂O₄ samples doped …

Flow-Tube Oxidation Experiments On The Carbon Preform Of Pica, Francesco Panerai, Alexandre Martin, Nagi N. Mansour, Steven A. Sepka, Jean Lachaud

Mechanical Engineering Faculty Publications

Oxidation experiments on the carbon preform of a phenolic-impregnated carbon ablator were performed in the NASA Ames ow-tube reactor facility, at temperatures between 700 and 1300 K, under dry air gas at pressures between 103 and 104 Pa. Mass loss, volumetric recession and density changes were measured at different test conditions. An analysis of the diffusion/reaction competition within the porous material, based on the Thiele number, allowed us to identify low temperature and low pressure conditions to be dominated by in-depth volume oxidation. Experiments above 1000 K were found at transition conditions, where diffusion and reaction occur at similar scales. …

Nanomaterials For Biological Applications: Drug Delivery And Bio-Sensing, Hui Ma

LSU New Orleans Theses and Dissertations

The idea of utilizing nanomaterials in bio-related applications has been extensively practiced during the recent decades. Magnetic nanoparticles (MPs), especially superparamagnetic iron oxide nanoparticles have been demonstrated as promising candidates for biomedicine. A protective coating process with biocompatible materials is commonly performed on MPs to further enhance their colloidal and chemical stability in the physiological environment. Mesoporous hollow silica is another class of important nanomaterials that are extensively studied in drug delivery area for their ability to carry significant amount of guest molecules and release in a controlled manner.

In this study, different synthetic approaches that are able to produce …

Synthesis Of Rhenium And Manganese Pyridazoal Complexes, Jesse Evans

Masters Theses & Specialist Projects

Pyridazines are a heterocyclic aromatic compound containing a characteristic N-N bond that are utilized in many fields, including medicine and electronics. It is this latter field that Dr. Snyder's research group is focused upon. Organometallic compounds are a better conducting material than the current inorganic compounds used in electronics due to better conductance of electricity, lower production cost, and the ability to be formed into thin films. With this in mind, Dr. Snyder's research group has set out to synthesize organometallic compounds for this purpose. Following procedures set forth by Snyder etc, and altered to form an off-metal route, we …

Study Of Immobilizing Cadmium Selenide Quantum Dots In Selected Polymers For Application In Peroxyoxalate Chemiluminescence Flow Injection Analysis, Christopher S. Moore

Electronic Theses and Dissertations

Two batches of CdSe QDs with different sizes were synthesized for immobilizing in polyisoprene (PI), polymethylmethacrylate (PMMA), and low-density polyethylene (LDPE). The combinations of QDs and polymer substrates were evaluated for their analytical fit-for-use in applicable immunoassays. Hydrogen peroxide standards were injected into the flow injection analyzer (FIA) constructed to simulate enzyme-generated hydrogen peroxide reacting with bis-(2,4,6-trichlorophenyl) oxalate.

Linear correlations between hydrogen peroxide and chemilumenscent intensities yielded regression values greater than 0.9750 for hydrogen peroxide concentrations between 1.0 x 10^-4 M and 1.0 x 10^-1 M. The developed technique’s LOD was approximately 10 ppm. Variability of the prepared …

Impedance Analysis Of Dielectric Nanoparticles Enabled Via A Self-Assembled Monolayer, Sasidhar Siddabattuni, Thomas P. Schuman, Vladimir Petrovsky, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Impedance spectroscopy has been shown to be a powerful tool to investigate the dielectric characteristics of powders suspended in suitable liquids. The electrical and dielectrical contributions of different components of the slurry can be extracted from the impedance spectra through measurement of frequency-dependent relaxations. However, for ferroelectric powders that possess innate surface conductivity, such as BaTiO₃, nanoparticles have sufficient conductivity to exclude low frequency fields that preclude impedance characterization of the particle core. In this work, the slurry technique is shown to be effective for dielectric characterization of not only micrometer-sized particles through equivalent circuit modeling but also …

New Effects Of Aging And Lattice Intercalation On Surface Properties Of Titanate Nanobelts, Roger Williams

Graduate Theses and Dissertations

Titanate nanobelts (NBs) have structural characteristics beyond that of clays. Due to a negatively charged lattice matrix of edge-shared TiO6-octahedra, the location of intercalated cations within the interlayer space may dictate the charge-conductions. This environment may in turn govern the lattice-framework's stability and surface properties, based upon our preliminary

data.

On that basis, these nanomaterials have been found in our lab to possess superb biological compatibility that is closely related to the types of the intercalated cations. In addition, a prolonged agitation was proven to enable us to manipulate the titanate NBs' length. In a parallel study, a ripening was …

Strategic Electronic Property Control Of Self-Assembling Pyrazine-Acenes, Lacie Brownell

UNLV Theses, Dissertations, Professional Papers, and Capstones

Control of electronic properties in organic semiconductor materials is essential for electro-optical applications such as field-effect transistors, light-emitting diodes, and photovoltaic devices. This work is focused on two systems that highlight different approaches for the manipulation of electronic properties: (I) the development of electron-deficient (n-type) materials by selective lowering of E_LUMO and (II) low energy gap materials by controlling both E_LUMO and E_HOMO

To specifically lower E_LUMO, a pyrazine-acene π-platform was extended using electron-withdrawing moieties. These include: pyridine, pyrazine, and benzothiadiazole (system I). From the base pyrazine-acene, the most significant change in E_LUMO of …

A Comparative Study Of Ce3+/Ce4+ Redox Couple On Pt Electrode In Sulfuric Acid And Methanesulfonic Acid, Zhao-Hua Li, You-Qun Chu, Chun-An Ma

Journal of Electrochemistry

The electrochemical oxidations of Ce³⁺ to Ce⁴⁺ on Pt rotating disk electrode (RDE) in both sulfuric acid and methanesulfonic acid (MSA) solutions were studied by using cyclic voltammetry and linear sweep voltammetry. The complexing behaviors of Ce³⁺/Ce⁴⁺ were preliminarily probed and the exchange current density, diffusion coefficient, as well as reaction rate constant were obtained from Butler-Volmer equation. The activation energies of Ce³⁺ oxidation on Pt electrode in two types of acidic media, obtained from Arrhenius equation, were also compared. The results indicate that Ce³⁺ can be oxidized to Ce4+ much easier in …