Chemistry Commons^™

Electrodeposited Semiconductor Nanostructures & Epitaxial Thin Films For Flexible Electronics, Naveen Kumar Mahenderkar

Doctoral Dissertations

"Single-crystal Si is the bedrock of semiconductor devices due to the high crystalline perfection which minimizes electron-hole recombination, and the dense native silicon oxide which minimizes surface states. To expand the palette of electronic materials beyond planar Si, an inexpensive source of highly ordered material is needed that can serve as an inert substrate for the epitaxial growth of grain boundary-free semiconductors, photonic materials, and superconductors. There is also a need for a simple, inexpensive, and scalable fabrication technique for the growth of semiconductor nanostructures and thin films. This dissertation focuses on the fabrication of semiconducting nanowires (polycrystalline Ge & …

Electrodeposited Epitaxial Cobalt Oxides And Copper Metal, Caleb M. Hull

Doctoral Dissertations

"Electrochemical deposition methods are presented for the deposition of Co(OH)₂ and Cu metal. Paper I shows the deposition of β-Co(OH)₂ on Ti through electrochemical reduction of [Co(en)₃]³⁺ to [Co(en)₃]²⁺ in 2M NaOH. The catalytic properties of the deposited Co(OH)₂ towards water oxidation is found comparable to Co₃O₄, with the surface of the Co(OH)₂ converting to CoOOH during the reaction. Paper II gives the conditions suitable for epitaxial growth of Co(OH)₂ on Au(100), Au(110), and Au(111) following the same reduction mechanism as described in Paper I. …

Targeting Metastatic Breast Cancer With Statin Drugs And Coq10, Jacob Thrasher

Honors Theses

Statin drugs are commonly prescribed to lower cholesterol levels in patients, but recently statins have been under investigation as a potential anti-cancer drug. Statins are HMG-CoA reductase inhibitors and subsequently inhibit the mevalonate pathway and cholesterol synthesis. Since cholesterol trafficking is vital in the growth and metastasis of cancer, statin drugs are being studied to explore their effects on cancer cells. CoQ10, one of the products from the mevalonate pathway, also has shown some potential anti-cancer properties, but its use to combat cancer is controversial. While some studies have shown that CoQ10 supplements can be synergistic with other cancer treatment …

Experimental Evaluation Of Uranyl Transport Into Mesoporous Silica Gel Using Fluorescence, Brandon M. Dodd

Theses and Dissertations

This research investigated parameters that can affect the use of nanoporous silica gel as a media for accumulating a detectable amount of uranium. The unique fluorescence of the Uranyl (UO₂²⁺) ion was used to evaluate the transport kinetics and accumulation within silica gel in a static fluid and under pressure driven flow. The addition of fluid flow decreased the time constant from on the order of an hour to approximately 2s with a very low fluid velocity of 0.36cm/s. The 0.36cm/s fluid velocity was found to be the critical velocity above which there was no gain in …

Development, Manufacture And Application Of A Solid-State Ph Sensor Using Ruthenium Oxide, Wade Lonsdale

Theses: Doctorates and Masters

The measurement of pH is undertaken frequently in numerous settings for many applications. The common glass pH probe is almost ideal for measuring pH, and as such, it is used almost ubiquitously. However, glass is not ideal for all applications due to its relatively large size, fragility, need for recalibration and wet-storage. Therefore, much research has been undertaken on the use of metal oxides as an alternative for the measurement of pH.

Here, a solid-state potentiometric pH sensor is developed using ruthenium metal oxide (RuO2). Initially, pH sensitive RuO2 electrodes were prepared by deposition with radio frequency magnetron sputtering (RFMS) …

Wildfire Emissions In The Context Of Global Change And The Implications For Mercury Pollution, Aditya Kumar

Dissertations, Master's Theses and Master's Reports

Wildfires are episodic disturbances that exert a significant influence on the Earth system. They emit substantial amounts of atmospheric pollutants, which can impact atmospheric chemistry/composition and the Earth’s climate at the global and regional scales. This work presents a collection of studies aimed at better estimating wildfire emissions of atmospheric pollutants, quantifying their impacts on remote ecosystems and determining the implications of 2000s-2050s global environmental change (land use/land cover, climate) for wildfire emissions following the Intergovernmental Panel on Climate Change (IPCC) A1B socioeconomic scenario.

A global fire emissions model is developed to compile global wildfire emission inventories for major atmospheric …

Analysis Of Vibrational Modes Of Chemically Modified Tone Wood, Madison Flesch

Honors Program Theses

It is generally accepted that every violin has different tone quality in terms of intonation and the depth of the harmonics produced. The best violins are made by experienced luthiers that craft each with precision to produce the best possible tonal quality. The quality of the finished violin is dependent upon both the specific shape and the vibrational response of the wood used in its construction. Because the hard wood used in violin construction is inhomogeneous, the composition and structure of material used is critical to the final product.¹ Luthiers would initially rely on their experience to feel the …

Preparation Of Nis2 Nanosheet And Its Application In Asymmetric Supercapacitor, Yuan-You Wang, Ya-Nan Liu, Dang-Qin Jin

Journal of Electrochemistry

In this work, the NiS₂ nanosheets have been synthesized using Ni(OH)₂  as a precursor through a sacrificial template method. The microstructure and chemical composition of as-prepared NiS₂ were characterized by XRD, EDS, BET, SEM and TEM techniques. The results showed that both Ni(OH)₂  and NiS₂  were composed of nanoplates. The electrochemical tests revealed that NiS₂ exhibited the high specific capacitance of 1067.3 F•g^-1 at a current density of 1 A•g^-1 and excellent rate performance. Furthermore, in order to evaluate the practical application of NiS₂, an asymmetric supercapacitor, NiS₂ as …

Electroactivities Of Pd/Fe3O4-C Catalysts For Electro-Oxidation Of Methanol, Ethanol And Propanol, Tao Zou, Qing-Feng Yi, Yuan-Yuan Zhang, Xiao-Ping Liu, Guo-Rong Xu, Hui-Dong Nie, Xiu-Lin Zhou

Journal of Electrochemistry

Development of palladium (Pd) catalysts with high electroactivity for alcohol oxidation is significant for alcohol fuel cells. In this work, Pd nanoparticles were formed by sodium borohydride (NaBH₄) reduction method and subsequently deposited on the surface of carbon supported ferriferrous oxide (Fe₃O₄/C) composites to obtain the Pd/Fe₃O₄-C catalysts with different Fe₃O₄ loadings. Their transmission electron microscopic (TEM) images show that the Pd nanoparticles were uniformly dispersed on the Fe₃O₄/C. Electroactivities of the prepared Pd/Fe₃O₄-C catalysts toward oxidations of C1-C3 …

Kinetics And Mechanism Toward Electrochemical Reductions Of Sodium Bromide And Methanol Over Iron Electrodes, Qun Liao, Shu-Feng Zhang, Wen-Hua Leng

Journal of Electrochemistry

It is of technological value and scientific interest to the electro-synthesis of ferrocene, conversion of carbon dioxide (CO₂) and organic electro-synthesis in non-aqueous solutions by investigating the kinetics and mechanism toward electrochemical reductions of sodium bromide (NaBr) and methanol over iron electrodes. However, few reports in the related researches are available. In this article, the kinetics and mechanism toward electrochemical reductions of NaBr and methanol over iron electrodes were examined in detail by carrying out the polarization curve and electrochemical impedance spectroscopic measurements. The results showed that methanol was the reactant, while Na⁺ ions were functioned only …

Effect Of Peg-Coating On Properties Of Lithium-Sulfur Battery Cathode Material Containing Carbon Fiber Conductive Agent, Jie-Cheng Tan, Yan-Hong Tian, Xue-Jun Zhang, Kai-Le Fan

Journal of Electrochemistry

The composite materials contained high modulus carbon fiber (HMCF) were successfully prepared by employing a ball-milling process based on the coating treatment of polyethylene glycol (PEG), and their structures and morphologies were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) techniques．The influences of PEG content on sulfur cathode capacity, cycle stability and rate performance were systematically studied. It was found that by the pre-coating of PEG, the cathode exhibited the high initial discharge specific capacity of 1312.5 mAh⋅g^-1 at a current rate of 0.2C, and the reversible discharge capacity of 650 mAh⋅g …

Capacity Fading Analyses Of Lini0.5Co0.2Mn0.3O2And Lini0.5Co0.2Mn0.3O2/Lifepo4 Cathode Materials For Lithium-Ion Battery, Yi Hu, Xiang-Zhu He, Zhong-De Deng, Ling-Yong Kong, Wei-Li Shang

Journal of Electrochemistry

The LiNi _0.5Co _0.2Mn _0.3O₂/LiFePO₄ (NMC532/LFP) composite cathode material for lithium-ion battery was prepared by wet ball-milling. The capacity fading behaviors of LiNi _0.5Co _0.2Mn _0.3O₂ (NMC532) and LiNi _0.5Co _0.2Mn _0.3O₂/LiFePO₄ (NMC532/LFP) were analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM), charge/discharge and electrochemical impedance spectroscopy (EIS) tests. The results indicated that the capacity retention values of NMC532/LFP were 97.80% and 86.48%, respectively, after 50 cycles and 60℃ high temperature storage. The NMC532/LFP exhibited better cycle performance and high temperature storage performance. …

Cobalt-Based Nitrogen-Doped Carbon Non-Noble Metal Catalysts For Oxygen Reduction Reaction, Meng-Xiu Jiang, Jing Zhang, Yue-Hua Li, Rong Zhang

Journal of Electrochemistry

Transition metal-nitrogen co-doped carbon catalysts have attracted significant attention because of their reasonable activity and remarkable selectivity toward oxygen reduction reaction (ORR) as cathodic reaction in fuel cells. However, the role of transition metal in the active sites of the catalysts still is uncertain. In this work, the Co_x-N_y/C-T catalysts were prepared with BP2000 as a carbon source, urea (Ur) as a nitrogen source and Co(OAc)₂•4H₂O as a metal precursor by a simple chemical method. Meanwhile, in order to optimize the ORR activity, the catalysts were synthesized with different amounts of Co …

Core-Shell Pd@Pt Ultrathin Nanowires As Durable Oxygen Reduction Electrocatalysts, Xin Wang, Yun-Jie Xiong, Liang-Liang Zou, Qing-Hong Huang, Zhi-Qing Zou, Hui Yang

Journal of Electrochemistry

This paper describes a simple CO-assisted reduction approach for the controllable synthesis of ultrathin Pd nanowires along the one-dimensional (1D) direction. Ultrathin Pt films from one to several atomic layers were successfully decorated onto ultrathin Pd nanowires by utilizing Cu UPD deposition, and followed by in-situ redox replacement reaction of UPD Cu by Pt. The core–shell structure and composition of the Pd@Pt ultrathin nanowires have been verified using transmission electron microscopy and energy dispersive X-ray spectrometry. The core–shell Pd@Pt ultrathin nanowires exhibited comparative electrocatalytic activity and improved durability for the oxygen reduction reaction in comparison with commercial Pt black. The …

Effect Of Allyl Thiourea On Nickel Electrodeposition From Solution Containing Ammonia And Chloride, Ya-Ning He, Liang Yuan, Zhi-Ying Ding, Shi-Jun Liu

Journal of Electrochemistry

The effects of allylthiourea (ATU) concentration on the cathodic polarization behaviour, nucleation and surface morphology of nickel electrodeposited on the glassy carbon electrode from ammonia-ammonium chloride-water (NH₃-NH₄Cl-H₂O) solutions were investigated by cyclic voltammogry, cathodic polarization and current transient methods. The results revealed that the addition of ATU inhibited nickel deposition, which was enhanced with an increase in ATU concentration from 5 to 50 mg•L^-1. The initial deposition kinetics corresponded to a model including instantaneous nucleation and diffusion controlled growth. In the presence of ATU, the initial nucleation of nickel electrocrystallisation remained unchanged. …

Effects Of Jet Milling And Classifying Process On The Performance Of Lifepo4/C In Full Batteries, Xing-Liang Liu, Mao-Ping Yang, Wei-Wei Wang, Yong Cao

Journal of Electrochemistry

The carbon coated lithium iron phosphate (LiFePO₄/C) composite cathode material was prepared by using iron phosphate process. The effects of jet milling and classifying process on the electrochemical performance of LiFePO₄/C cathode material in full batteries were investigted. Scanning electron microscopic analyses suggested that the globose secondary particles were crustily crushed during the jet milling and classifying process, which would further result in lower tap density and carbon content. The LiFeP₄/C composite cathode materials with different physical characteristics were further tested in full batteries to evaluate the electrochemical properties. The results showed no obvious …

Engineering The Electrochemical Capacitive Properties Of Activated Carbon By Correct Selection Of Ionic-Liquid Electrolytes, Qiu-Hong Zhang, Bao-Shou Shen, Song-Lin Zuo, Xin-Yu Wei

Journal of Electrochemistry

In order to improve the electrochemical capacitive properties and to apply coconut shell activated carbon (AC) serving as electrode materials in ionic liquid (IL)-based supercapacitor (SC), the coconut shell AC material was re-activated using a steam as an activating agent in this work, forming a secondary AC (W-AC). The results showed that the specific capacitance of the W-AC electrode was much larger than that of the raw activated carbon electrode (R-AC) in 1-ethyl-3-methylimidazolium tetrafluoroborate ([EMIM]BF₄). The electrochemical techniques including cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) measurement, and electrochemical impedance spectroscopy (EIS) were used to systematically study the capacitive …

Applications Of N-Methyl-N-Butyl-Pyrrolidinium Bromide And N-Methyl-N-Ethyl-Pyrrolidinium Bromide In Zn-Br Flow Batteries, Qi Zhang, Miao-Miao Zhang, Lin Meng

Journal of Electrochemistry

It is extremely important for battery performance and safety in Zn-Br flow battery to use quaternary ammonium salts as complex agents for bromine. In this work, the effects of electrolyte compositions and concentrations on the electrode reactions and battery performances were studied in the absence and presences of N-methyl-N-ethyl-pyrrolidinium bromide (MEP) or N-methyl-N-butyl-pyrrolidinium bromide (MBP). The conductivities in the electrolytes containing different constitutions and concentrations were measured by EIS method. The charge-discharge performance for the battery and the complex ability for bromine in different electrolytes were also investigated. The results showed that the electrolyte containing MBP was better than that …

Effect Of Fe2+/Fe3+Interconvertion On Reduction Behavior Of Fe3+ In Acidic Electrolytes, Jian-Xin Qin, Feng Lin, Wen-Ping Liu, Chao Chen, Meng-De Ren

Journal of Electrochemistry

The influences of ferrous/ferric (Fe²⁺/Fe³⁺) interconvertion on electrochemical reduction and electrode reaction of Fe³⁺ were investigated by using linear sweep voltammetry, potentiostatic method and cyclic voltammetry (CV) in acidic electrolytes containing chloride ion (Cl^-) and sulfate ion (SO₄^2-). It was shown that the reduction process of Fe³⁺/Fe²⁺ would take place in two independent stages: (1) the reduction of Fe³⁺ to Fe²⁺ at E=0.35V and (2) the co-precipitation of Fe²⁺ by forming Fe(OH)₂ (E≤-0.3 V) instead of Fe. The major effect of Fe^{2+ …}

Effect Of Calcium On Atmospheric Corrosion Resistance Of Bridge Steel, Dong-Liang Li, Gui-Qin Fu, Miao-Yong Zhu

Journal of Electrochemistry

The corrosion behavior of bridge steel in simulated hot and humid industrial-marine atmosphere was investigated by mass loss analysis, XRD, SEM, electrochemical methods and a wet/dry alternate immersion corrosion test using 0.1 mol•L^-1 NaCl+0.01 mol•L^-1 NaHSO₃ solutions. The corrosion depth (W) of experimental steels before and after calcium treatment versus time (t) curves showed a good agreement with the power function of W=Atⁿ. The corrosion products were mainly composed of amorphous phase and a small amount of crystals including α-FeOOH, β-FeOOH, γ-FeOOH and Fe₃O₄. Trace calcium could promote the formation of …

Three-Dimensional Nanomaterials For Supercapacitor Applications: From Metal Oxides To Metal Phosphides, Zhi Zheng

LSU New Orleans Theses and Dissertations

Over the past few years, energy storage devices have received tremendous interest due to the increasing demand for sustainable and renewable energy in modern society. Supercapacitors are considered as one of the most promising energy storage devices because of their high power density and long cycle life. However, low energy density remains as the main shortcoming for supercapacitors. The overall performance of supercapacitors is predominantly determined by the characteristics of the electrodes. Specifically, constructing nanostructured electrode material has been proven as an efficient way to improve the performance by providing large surface area and short ionic and electronic diffusion paths. …

The Role Of Catalytic Residue PKA On The Hydrolysis/Transglycosylation Partition In Family 3 Β-Glucosidases, Inacrist Geronimo, Christina M. Payne, Mats Sandgren

Chemical and Materials Engineering Faculty Publications

β-Glucosidases (βgls) primarily catalyze the hydrolysis of the terminal glycosidic bond at the non-reducing end of β-glucosides, although glycosidic bond synthesis (called transglycosylation) can also occur in the presence of another acceptor. In the final reaction step, the glucose product or another substrate competes with water for transfer to the glycosyl-enzyme intermediate. The factors governing the balance between the two pathways are not fully known; however, the involvement of ionizable residues in binding and catalysis suggests that their pK_a may play a role. Through constant pH molecular dynamics simulations of a glycoside hydrolase Family 3 (GH3) βgl, we …

The Future Of Nuclear Security In Moroccan Territory After The Creation Of The New Moroccan Agency Of Nuclear And Radiological Safety And Security: Opportunities And Challenges, Amal Touarsi, Amina Kharchaf

International Journal of Nuclear Security

Nowadays, a security regime for protecting nuclear and radiological material—providing an intelligent national regulatory institution and establishing national security laws—is necessary in order for a state to ensure security of nuclear and radiological materials used within its borders.

This paper focuses on discussing the opportunities and challenges facing the future of nuclear security after the creation of the new Moroccan Agency of Nuclear and Radiological Safety and Security.

Assessing And Enhancing Nuclear Safety And Security Culture For Small Facilities That Handle Radioactive Material, Solymosi Máté

International Journal of Nuclear Security

The use of radioactive sources is expanding all over the world and abreast the necessity of the enhancement of its safe and secure application is increasing too. In the nuclear industry, the safety and security are top priorities since decades. They share the same goal, to protect humans from the negative affect of the ionizing radiation. The human component of them is a significant factor and technical solutions can protect us so far and thus the culture for safety and security become a major focus. On the other hand, there are still some contradiction between recommendations and international guidance of …

Two-Component Hydrogel As Biomimetic Vitreous Substitutes, Sruthi Santhanam

McKelvey School of Engineering Graduate Student Theses & Dissertations

The vitreous humor of the eye is a biological hydrogel principally composed of fibrillary collagen interspersed with semi-flexible polyelectrolyte, hyaluronic acid (HA). Certain pathological conditions necessitate its removal and replacement. Current vitreous substitutes, such as silicone oils and perfluorocarbons, are hydrophobic, do not resemble the properties of the vitreous, and have known complications. An ideal vitreous substitute should have properties of the natural vitreous, perform its functions, and be biocompatible in the eye. Inspired by the structure and composition of the natural vitreous, we used bio-mimicry to develop an injectable two-component hydrogel. The hydrogel is composed of a fibrillary gellan, …

Layer-By-Layer Assembled Membranes With Immobilized Porins, Sebastián Hernández, Cassandra Porter, Xinyi Zhang, Yinan Wei, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

New and advanced opportunities are arising for the synthesis and functionalization of membranes with selective separation, reactivity, and stimuli-responsive behavior. One such advancement is the integration of bio-based channels in membrane technologies. By a layer-by-layer (LbL) assembly of polyelectrolytes, outer membrane protein F trimers (OmpF) or “porins” from Escherichia coli with central pores ∼2 nm in diameter at their opening and ∼0.7 × 1.1 nm at their constricted region are immobilized within the pores of poly(vinylidene fluoride) microfiltration membranes, in contrast to traditional ruptured lipid bilayer or vesicle processes. These OmpF-membranes demonstrate selective rejection of non-charged organics over ionic solutes, …

Synthesis And Characterization Of Thermoresponsive Hydrogels Based On N-Isopropylacrylamide Crosslinked With 4,4′-Dihydroxybiphenyl Diacrylate, Shuo Tang, Martha Floy, Rohit Bhandari, Manjula Sunkara, Andrew J. Morris, Thomas D. Dziubla, J. Zach Hilt

Chemical and Materials Engineering Faculty Publications

A novel crosslinker [4,4′-dihydroxybiphenyl diacrylate (44BDA)] was developed, and a series of temperature-responsive hydrogels were synthesized through free radical polymerization of N-isopropylacrylamide (NIPAAm) with 44BDA. The temperature-responsive behavior of the resulting gels was characterized by swelling studies, and the lower critical solution temperature (LCST) of the hydrogels was characterized through differential scanning calorimetry. Increased content of 44BDA led to a decreased swelling ratio and shifted the LCST to lower temperatures. These novel hydrogels also displayed resiliency through multiple swelling–deswelling cycles, and their temperature responsiveness was reversible. The successful synthesis of NIPAAm-based hydrogels crosslinked with 44BDA has led to a …

Artificial Olfactory System For Multi-Component Analysis Of Gas Mixtures., Alexander Aleksandrovich Larin

Electronic Theses and Dissertations

Gas analysis is an important part of our world and gas sensing technology is becoming more essential for various aspects of our life. A novel approach for gas mixture analysis by using portable gas chromatography in combination with an array of highly integrated and selective metal oxide (MOX) sensors has been studied. We developed a system with small size (7 x 13 x 16 inches), low power consumption (~10 W) and absence of special carrier gases designed for portable field analysis (assuming apriori calibration). Low ppb and even sub-ppb level of detection for some VOCs was achieved during the analysis …

Green Chemistry Oxidative Modification Of Peptoids Utilizing Bleach And Tempo, Jesse Leland Roberts

Graduate Theses and Dissertations

Biotherapeutic drugs, derived from biological molecules such as proteins and DNA, are becoming an integral and exceptionally critical aspect of modern medicine. Compared to common pharmaceutical drugs, biotherapeutics are much larger in size and have greater target specificity, allowing them to treat many chronic diseases ranging from cancer to rheumatoid arthritis. The major issue with protein based therapeutics is that they readily undergo proteolysis, or enzymatic degradation, when administered through subcutaneous injections. Traditionally, biotherapeutic modification procedures have centered on the use of PEG derivatives. This process, called PEGylation, is unfavorable due to the increases in molecular weights of the proteins …

Controlled Electrochemical Reduction Of Gold And Palladium Metal Precursors In Polyaniline, Nicole Goodwin

UNLV Theses, Dissertations, Professional Papers, and Capstones

Polyaniline (PANI) has been extensively studied due to its unique electrochemical properties. The conjugated polymer is conductive with high chemical stability below 100°C, mechanical strength, and large surface area. The applications of PANI have included chemical sensing, corrosion inhibition coatings, light emitting diode and as a substrate for metal composite catalysts. Both chemical and electrochemical methods have been developed and utilized in the synthesis of PANI/metal composites. The simultaneous reduction of aniline and metal precursor produces a composite of PANI encapsulated metal, reducing the active surface area available for catalysis. Alternatively, chemical reduction of the metal precursor into preformed PANI …