Operations Research, Systems Engineering and Industrial Engineering Commons^™

Optimization Of Vehicle Mix For Three-And Four-Wheel Passenger Transportation System In Nigeria, Omotunde A. Muyiwa, Hamid A. Jimoh, Kolawole T. Oriolowo

Tanzania Journal of Engineering and Technology (TJET)

Efficient transportation systems are essential for reducing passengers waiting times in densely populated areas. However, there is a dearth of information on the optimization of vehicle mix for three-and four-wheel transportation systems in Nigeria. The present study was designed to optimize the vehicle mix for three-and four-wheel passenger transportation to improve transportation efficiency. Twenty purposively selected vehicles were observed, while a queuing model (M/M/s) was used to determine passenger arrival rates during different periods (morning, afternoon, and evening). An integer linear programming model was developed to minimize passenger waiting times. Data on vehicle types, capacities, travel cycles, and average passenger …

Implementation Of The Fourth Industrial Revolution Technologies In Tanzania’S Downstream Oil And Gas Industries, Vitalis John Mwinyi

Tanzania Journal of Engineering and Technology (TJET)

The advent of the fourth industrial revolution (IR4.0) has resulted in the digital transformation of multiple sectors of the economy due to the disruptive nature of the technologies driving the revolution. The technologies have already found their way into the oil and gas industries across the globe, especially in upstream, midstream, and downstream operations. However, the degree of implementation is not the same for these operations, considering the complexities involved, integrated process, the associated risk and investment cost, among others. This study aimed to establish the implementation level of IR4.0 technologies in the downstream operations. A survey method was employed …

Analysis Of Factors Enabling Organisational Governance Maturity For The Technical Audit Function In Tanzania, George C. Haule

Tanzania Journal of Engineering and Technology (TJET)

The study aimed to identify key factors contributing to Organisational Governance Maturity (OGM) of the Technical Audit Functions (TAF) in Tanzania.  The study employed a sequential approach as a research design.  The first step was to collect and analyse literature studies to identify factors enabling the OGM of the TAF.  Next, a questionnaire was administered to one hundred twenty-eight (128) respondents from seven (7) TAFs to rank the key enabling factors that were identified from the literature that influence the OGM of TAF in Tanzania.  Using data from a questionnaire administered to 128 respondents, a two-step strategy was employed to …

Revitalising Tanzania’S Textile Industry Through The Uk Textile System’S Role, Charles M. Kahabi

Tanzania Journal of Engineering and Technology (TJET)

Currently, there is the environmental and social challenges emerging from the global clothing and textile industry, specifically on textile waste management.  Additionally, the flow of second-hand clothing (SHC) between European countries especially the UK and Tanzania is increasing. In the UK, rapid growth of second-hand clothing (mitumba) driven by fast fashion results in vast quantities of discarded garments, of which only a fraction is recycled, leaving the remainder in landfills. Conversely, Tanzania has long depended on imported SHC a practice that, while affordable, has undermined local textile industries and contributed to waste accumulation. By examining Tanzania’s textile landscape, the research …

A Causal Inference Methodology For Root-Cause Diagnosis In Nonstationary Industrial Time Series, Cansu Yalim

Knowledge and Creativity Expo

Industrial fault diagnosis lacks a procedure that learns time-varying causal structure from observational time series, makes identifiability limits explicit, and uses intervention-based reasoning to support root-cause assessment under industrial constraints. Although predictive maintenance can reduce downtime, diagnosis is often expert-rule-based or association-driven; pipelines may elevate downstream symptoms alongside true drivers and provide limited guidance on which feasible action would change a fault trajectory under current operating conditions. Because operating phases and fault progression create regime shifts, industrial systems rarely follow a single stable mechanism. This study develops and evaluates a three-stage, regime-aware causal diagnostic protocol based on a time-varying Dynamic …

Investigation Of Process Parameters To Fabricate Tiwmo Refractory Medium Entropy Alloy Via Laser Powder Bed Fusion, Abdullah Al Masum Jabir, Lindsey A. Salazar, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

This paper presents an experimental study on the fabrication of a TiWMo refractory medium-entropy alloy (RMEA) using laser powder bed fusion (PBF-LB/M, commonly known as selective laser melting) from elemental powders as well as successful alloy formation on titanium substrates. The effects of tungsten particle size and process parameters on successful TiWMo RMEA fabrication have been explored using scanning electron microscopy (SEM), x-ray diffraction, hardness measurement and microstructural analysis. Scanning electron microscope (SEM) analysis revealed that the lowest percentage (0.01%) of unmelted tungsten particles was observed at a laser power of 350 W and scanning speed of 250 mm/s, particularly …

Optimizing Warranty Policies For Remanufactured Products: When Should They Be Longer, Shorter, Or Identical To New Product Warranties?, Kunpeng Li, Jun-Yeon Lee

Faculty Publications

Manufacturers adopt different warranty strategies for remanufactured products, offering shorter, identical, or longer warranty periods compared to new products. However, prior research has only focused on manufacturers offering either shorter or identical warranties. In addition, the existing literature has not captured the diminishing returns of warranties, i.e., as the warranty coverage increases, its incremental benefits begin to decrease but the costs continue to increase. To address these gaps, we develop an optimization model that jointly considers pricing and warranty decisions while accounting for warranty’s diminishing effect on consumer’s willingness to pay for remanufactured products. We show that all three observed …

Multi-Objective Optimization Of Waste Incineration For Minimal Carbon Monoxide And Sulfur Dioxide Emission And Rate Maximization: A Case Study Of Mbezi, Mkuranga-Pwani, Tanzania, Grangay M. Nyanghura, Enock W. Nshama

Tanzania Journal of Science

Incineration is widely employed for hazardous waste disposal, but results in harmful flue gas emissions. This study optimizes a double-chamber incineration process to reduce sulfur dioxide (SO2) and carbon monoxide (CO) emissions while maximizing the incineration rate. The effects of waste mass, primary chamber temperature (PT), and secondary chamber temperature (ST) were analyzed using a full factorial design of 27 experiments. ANOVA revealed that mass had the greatest impact on emissions and incineration time, ST had a moderate effect, and PT had little influence. Regression analysis provided models for incineration time, CO, and SO2 emissions. Single-objective optimization using sequential quadratic …

Layer-Wise Printing Parameter Optimization For Laser Powder Bed Fusion, Chaoran Dou, Rongxuan Wang, Raghav Gnanasambandam, Jianzhi Li, Zhenyu James Kong

Manufacturing & Industrial Engineering Faculty Publications

Additive manufacturing (AM) is a transformative technology that enables the fabrication of complex geometries layer by layer. However, metal parts produced via AM processes such as laser powder bed fusion (LPBF) are prone to various defects, including porosity and deformation. These defects often result from suboptimal printing parameter settings. Traditional approaches typically aim to reduce defects by optimizing a fixed set of parameters for the entire part. However, such methods do not account for layer-wise variations in printing conditions caused by changes in geometry, heat transfer, and re-heating effects. While optimizing parameters for each layer could improve part quality, it …

Reinforcement Learning For Imbalanced Data In Robotic Anomaly Detection Within Autonomous Manufacturing, Salma Messaoudi, Ahmed Bendaouia, El Hassan Abdelwahed, Mohammed Ameksa, Hajar Mousannif, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

Ensuring reliable anomaly detection in industrial robots is critical for safe and autonomous manufacturing operations. However, it remains challenging due to temporal dependencies and class imbalance in sensor data. This study presents a reinforcement learning approach using Deep Q-Network (DQN) enhanced with Long Short-Term Memory (LSTM) and Gradient Boosting Machine (GBM) for robust anomaly detection in robotic systems. The proposed framework integrates an LSTM into the DQN policy to capture temporal patterns. It also introduces a novel GBM-based reward mechanism that mitigates class imbalance by applying SMOTE (Synthetic Minority Over-sampling Technique) after removing temporal dependencies. Experimental results demonstrate that this …

Artificial Intelligence And Additive Manufacturing As A Coupled Design System: Rethinking Inference, Manufacturability, And Design Education, Charul Chadha, Garth Crosby, Sabit Ekin, Mohamed Gharib, Eman Hammad, Congrui Jin, Ali Ahmad Malik, Noemi Mendoza Diaz, Calahan Mollan, Monsuru Ramoni

Manufacturing & Industrial Engineering Faculty Publications

Artificial intelligence (AI) is becoming deeply integrated into additive manufacturing (AM) workflows, reshaping how designers approach geometry, materials, and process constraints. AI holds significant potential by accelerating design exploration, revealing complex patterns in AM behavior, and supporting earlier assessment of manufacturability. At the same time, it introduces new risks related to model transparency, data quality, physical validity, and the potential for overreliance by students and practitioners. This perspective examines these issues through four guiding questions that address the role of AI in AM-enabled design, the gaps that limit or enable AI contribution, the implications for engineering education, and the responsibilities …

Harnessing Ml And Iiot For Traceability In Continuous Production Systems: A Conceptual Framework, Kholoud M. Abdelaal

Theses and Dissertations

In the era of rapid technological advancement, the manufacturing sector faces increasing pressure to leverage emerging technologies to enhance operational efficiency and minimize waste. In this context, traceability plays a pivotal role, as it provides complete visibility of processes and products throughout manufacturing systems, enabling them to identify areas for improvement and take corrective actions accordingly. Additionally, traceability ensures compliance, supports product recalls, provides a clear understanding of the system’s performance, and enables fact-driven decision-making in multiple aspects of the manufacturing system. Although the broad spectrum of traceability applications in batch production-based plants, traceability remains challenging to achieve in continuous …

Performance, Economic And Environmental Evaluation Of A Solar-Assisted Vacuum Deaeration Heating System., Liew Shan Kun

Student Works (2020-2029)

This research evaluates the performance of a solar-assisted heating (SAH) system for makeup water in a vacuum deaeration process. The system integrates solar energy into the heating process, with parametric analysis conducted across varying configuration of total solar radiation and water flow rates. The total solar radiation at the experimental site in Kuala Kangsar, Perak, Malaysia, characterized by tropical weather, fell within the range between 414W/m2 to 568W/m2. Performance analysis showed that a flow rate of 0.4 LPM achieved the target temperature of 61°C required for the deaeration process. Thermal efficiency peaked at 62.60% under a solar radiation of 900 …

Reinforced Scan: A Reinforcement Learning Enabled Optimal Laser Scan Path Planning In Laser Powder Bed Fusion Additive Manufacturing, Chaoran Dou, Jihoon Chung, Raghav Gnanasambandam, Yuhao Wu, Jianzhi Li, Zhenyu James Kong

Manufacturing & Industrial Engineering Faculty Publications

Additive Manufacturing is an innovative technology that fabricates parts layer by layer. However, in Laser Powder Bed Fusion (LPBF), printed metal parts often exhibit residual stresses, deformations, and other defects due to non-uniform temperature distribution during the printing process. To mitigate these issues, an optimized scan sequence within each layer can improve thermal uniformity. Traditional optimization methods, which rely on domain knowledge and employ trial-and-error or heuristic approaches, often fail to achieve optimal solutions due to the complex nature of the problem. One major challenge in improving scan strategies lies in the vast search space required to optimize the scan …

Optimal Placement Of Electric Vehicle Chargers: A Mixed-Integer Linear Programming Model, Joubin Zahiri Khameneh, Emmanuel Fagbenle

Faculty Publications

Electric vehicle adoption is growing, but New Hampshire lags in public charging infrastructure, especially in rural areas. This gap increases range anxiety and economic inefficiencies. In this study, we developed a mixed-integer linear programming (MILP) model to optimally locate new electric vehicle chargers statewide, maximizing coverage and equity under budget constraints. The model includes geographic coverage requirements, population-weighted equity, capacity limits, and a $28 million budget. Moreover, the model recommends 855 Level 2 chargers and 149 Direct Current Fast Chargers (DCFCs) across 247 ZIP Codes, nearly doubling public charging capacity and achieving 98.8% coverage within defined service radii. The plan …

Direct Ink Writing Of Shear Exfoliated Two-Dimensional Nanomaterial- Elastomeric Multifunctional Nanocomposite, Md Abdur Rahman Bin Abdus Salam, Asif Hasan Ridoy, A K M Abirul Haque, Muhammad Shahbaz Rafique, Md Arafat Hossain, Md Shahriar Forhad, Matthew G. Boebinger, Farid Ahmed, Karen Lozano, Ali Ashraf

Manufacturing & Industrial Engineering Faculty Publications

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman …

Proactive Safety Reasoning In Human-Robot Collaboration In Disassembly Through Llm-Augmented Stpa And Fmea, Morteza Jalali Alenjareghi, Fardin Ghorbani, Samira Keivanpour, Yuvin Adnarain Chinniah, Sabrina Jocelyn

Études primaires

Disassembly tasks in human–robot collaboration (HRC) environments present safety challenges due to hazardous materials, control system variability, and physically demanding operator tasks. To address these challenges, we propose an AI-augmented risk assessment framework integrating System-Theoretic Process Analysis (STPA) and Failure Mode and Effects Analysis (FMEA). This framework is implemented in four configurations: Term Frequency– Inverse Document Frequency (TF-IDF), Fine-tuned Large Language Models (LLMs), Retrieval-Augmented Generation (RAG), and RAG with a structured Knowledge Graph (KG) built from safety standards. The system supports real-time, standards-compliant safety reasoning by generating interpretable, context-specific recommendations. We evaluate these configurations across GPT-3.5 TURBO, GPT-4o, GPT-4.1, and …

Identifying Industry-Preferred Automation Software In Engineering: An Indeed-Based Analysis To Inform Engineering Technology Curriculum Design, Triet Minh Phan, Collins Okafor, Winifred Okafor, Devang Mehta, Mohsen Souissi, Jenora Waterman, Connie Mayberry, Misty Thomas, Orlando Ayala, Angie Price, Maurizio Manzo

Engineering Technology Faculty Publications

In the evolving field of automation engineering, staying aligned with industry software demands is critical to preparing graduates for the modern workforce. This study investigates the prevalence of leading industrial automation platforms—Rockwell / Allen-Bradley (RSLogix / Studio 5000), Siemens (TIA Portal / Step 7), and Schneider Electric (EcoStruxure / Unity Pro)—across job postings collected from Indeed using the keyword "automation engineering." The research compiles a structured dataset of job postings with seven fields: ID, Job Title, Organization, Rockwell / Allen-Bradley, Siemens, Schneider Electric, and Posting URL. Each entry is manually coded to indicate whether the listed software platforms are mentioned, …

Ai-Based Porosity Detection In Babbitt Bore Turning, Kaylee Leggett, Hannah Adams Gemmell, Kaisa Shingleton

Williams Honors College, Honors Research Projects

For this project, an external company reached out to the University of Akron requesting assistance with defect detection during their vertical turning operations. As babbitt is removed in a vertical turning process, it occasionally reveals defects, mainly porosity, which can lead to costly downstream failures of the part. Current inspection techniques involve use of dye penetrant, which is time consuming, labor intensive, unergonomic, and a source of human error. The goal of the project is to create an alternative inspection method using an AI-based machine-learning model. After the turning operation, a camera is deployed to perform an in-place inspection, taking …

A Three-Stage Causal Root-Cause Diagnostic Protocol For Nonstationary Industrial Time Series Data, Cansu Yalim, Resit Unal, Holly A. H. Handley

Engineering Management & Systems Engineering Faculty Publications

Predictive maintenance (PdM) systems effectively forecast failures, but they often fail to find root causes, particularly when system dynamics change over time. This limitation arises from applying static causal models or decoupled segmentation to handle nonstationary industrial time series. For regime-aware causal diagnostics and interventional effect estimation, we introduce a three-stage time-varying dynamic Bayesian network (TV-DBN) protocol. Using a minimum description length (MDL) objective that connects segmentation to mechanism changes, Stage I jointly infers change points and regime-specific graph structure. Stage II produces a completed partially directed acyclic graph (DAG) by orienting edges within each regime using a combination of …

Seeing Feedback Differently: Enhancing Learning Through Individualized Video Feedback, Makenzie Khristine Keepers

2026 Scholarly Teaching Conference: Concurrent Session Papers

Students often seek feedback that goes beyond rubric scores, especially for complex assignments like project reports where expectations are nuanced. Transitioning from lengthy written comments to personalized video responses has proven to be an effective alternative. These videos provide students with clear explanations of strengths and areas for growth, while walking them through their work in detail. Feedback from learners suggest that video feedback feels more comprehensive and accessible, helping them better understand mistakes and apply corrections. Importantly, producing video feedback requires comparable effort to traditional written comments, yet offers greater impact for formative assessments that shape performance on summative …

Nanostructured Cathode Catalysts For Aem Electrolysis: From Catalyst Design To Degradation And Hydrogen Dynamics, Yamini Kumaran

Electronic Theses & Dissertations (2024 - present)

Anion exchange membrane water electrolysis (AEMWE) presents a promising pathway toward cost-effective and sustainable hydrogen production by integrating the chemical robustness of alkaline systems with the compact, zero-gap design of proton exchange membrane electrolyzers. However, the widespread implementation of AEMWE is limited by the availability of highly active and durable platinum-group-metal (PGM)-free catalysts and by an incomplete understanding of their degradation behavior under realistic operating conditions.

This dissertation focuses on the development, characterization, and mechanistic investigation of nanostructured MoNi₄–MoO₂-based electrodes for efficient and stable hydrogen generation under alkaline and membrane-integrated environments. MoNi₄–MoO₂ nanorods …

Simulation Optimization Of Intermodal Freight Transportation Under Disruptions, Israt Humayra

Graduate Theses, Dissertations, and Problem Reports (ETD)

Rapid growth in freight transportation in modern supply chains has led to increased operational costs, congestion, and severe environmental impacts, especially greenhouse gas emissions. Combining different modes, such as highway, railway, and waterway, intermodal transportation could thus offer considerable benefit to improve efficiency, sustainability, and resilience. However, most existing planning approaches rely on simplified assumptions, fixed schedules, and average cost estimates, making them less relevant to dealing with real-world uncertainties and disruptions. This study develops a simulation-optimization framework for intermodal freight transportation under disruption. We develop a mixed-integer programming model to represent an intermodal logistics planning framework on a multi-layered …

Anaerobic Digestion Of Food Waste Components: Modeling Biogas Production, Opeyemi E. Adelegan

Civil Engineering Dissertations

Food waste constitutes the single largest component of municipal solid waste landfilled in the United States — approximately 22% of 292.4 million tons generated in 2018 — and its anaerobic decomposition releases methane, a greenhouse gas with global warming potential approximately 27–30 times that of carbon dioxide over a 100-year horizon (IPCC, 2021). Anaerobic digestion (AD) offers an alternative management pathway that recovers energy and produces nutrient-rich digestate, but AD performance varies by as much as five-fold across food waste streams (130–630 m³ CH₄ per Mg VS added), and existing predictive tools either treat food waste as a …

An Integrated Pull System Framework For Disassembly Industries: Bridging The Supply-Demand Mismatch In Duck Meat Processing, Hongchao Yu

Graduate Research Theses & Dissertations

Disassembly-based production systems, such as duck meat processing, face inherent operational challenges due to one-to-many production structures, short product shelf life, and volatile customer demand. A single carcass must be processed into multiple products at largely fixed biological ratios, while demand varies across products and over time. This supply-demand mismatch frequently leads to simultaneous surplus and shortage, resulting in unstable shipment schedules, excess inventory, and unavoidable waste. Traditional order-driven pull systems typically respond to orders independently and are limited in their ability to coordinate these interrelated effects.

This dissertation develops an integrated pull system framework for perishable disassembly processes, using …

Lean Service System Optimization In U.S. Automotive Maintenance Centers: A Time Study And Simulation-Based Approach To Reducing Service Cycle Time And Increasing Efficiency, Rakibul Hasan Sarker

All Graduate Theses, Dissertations, and Other Capstone Projects

The primary objective of this study is to measure the current service time at a U.S. automobile service center, with the aim of reducing waste and optimizing service operations through time study and simulation modeling. Inefficiencies in those service centers increase service time and labor costs, reduce service quality, and reduce workshop productivity, thereby increasing customer waiting time. In this study, real-world shop floor data were collected from a single service center, namely Jiffy Lube. Over the course of ten working days, 205 vehicle data points were acquired. Service time, bay time, and overall process time were computed and examined …

Bridging Mission And Execution: Integrating Participatory Design In Early-Phase Mission Engineering For Stakeholder Alignment And Mission Clarity, Rafi Soule

Knowledge and Creativity Expo

This research examines mission framing during the early phase of Mission Engineering. Stakeholder interpretations diverge under ambiguity. Interoperability constraints are often not surfaced early. These conditions reduce mission clarity and weaken mission-to-system mapping readiness. The study integrates a participatory design-inspired, artifact-first workflow with RAG-enabled retrieval from a closed corpus to support evidence-grounded reasoning and traceable citations.

Phase 1 uses an online survey to establish baseline patterns in practice (N = 86). Shared understanding is positively associated with mission clarity (r = 0.60, p < 0.001). Phase 2 uses a time-bounded comparative workshop with two conditions. Expert reviewers rate mission statement quality higher for the participatory design condition (mean 3.5) than the traditional condition (mean 2.8). Technical feasibility ratings are similar across conditions. Phase 3 demonstrates RAG-enabled, closed-corpus, retrieval-supported traceability using the Referencer tool. It is reported as a proof-of-concept for evidence-grounded rationale and auditability, and as a pathway …

Generative Ai-Driven Optimization In Flexible And Reconfigurable Manufacturing Systems, Salah Hammedi, Hicham Chaoui, Lotfi Nabli

Electrical & Computer Engineering Faculty Publications

Flexible and Reconfigurable Manufacturing Systems (FRMSs) are essential for coping with variability in modern production environments; however, efficient scheduling and rapid reconfiguration remain challenging. This paper presents a hybrid optimization framework that integrates Colored Petri Net (CPN) modeling with Generative Artificial Intelligence (GenAI) to enhance scheduling performance and system adaptability. The CPN formalism ensures verifiable modeling of system dynamics, while a transformer-based generative model produces candidate scheduling and reconfiguration strategies. Simulation experiments were conducted under static, dynamic, and adaptive scenarios, including machine breakdowns and dynamic job arrivals. Performance was evaluated using makespan, mean flow time, machine utilization, and reconfiguration latency. …

A Study Of Perceptions, Readiness, Benefits, And Barriers Related To Exoskeleton Adoption In New Jersey’S Warehousing Sector, Terry Asante

Theses

The warehousing industry in New Jersey remains a vital component of the region's logistics network, employing more than 200,000 workers who routinely engage in lifting, bending, overhead reaching, and other physically demanding activities. These exposures contribute to musculoskeletal disorder (MSD) rates that exceed national averages, particularly affecting the low back and shoulders. Nationally, MSDs account for an estimated $420 billion in combined direct and indirect costs each year, underscoring the need for interventions that can effectively reduce biomechanical strain. Industrial exoskeletons have emerged as a potential solution, with prior research demonstrating reductions in muscle activation, perceived exertion, and fatigue during …

Optimization Of Welding Parameters For Carbon Steel Fabrication: A Trade-Off Between Tensile Strength And Heat-Affected Zone, Melkiory B. Njawala, Simon I. Marandu, Enock W. Nshama

Tanzania Journal of Engineering and Technology (TJET)

This study focused on optimizing gas metal arc welding (GMAW) parameters for AISI 1045 carbon steel to balance the ultimate tensile strength (UTS) and heat affected zone (HAZ) size of the weldment. Using a full factorial design of experiments (27 trials), the influence of welding current, arc voltage, and travel speed on UTS and HAZ size of AISI 1045 carbon steel weldments were investigated. From the analysis of results, using Analysis of variance (ANOVA) technique, the results revealed that current, travel speed and arc voltage contributed 74.41%, 19.05% and 0.04%, respectively, to the total percentage of variations on UTS data. …