Other Mechanical Engineering Commons^™

Elevate Hardcase, Caleb J. Bailey, Colby M. Cordoba, Marissa Mccleod, Shaan Sandhu

Mechanical Engineering

The Elevate Hardcase project developed a portable mechanical elevation system that allows users to access rugged hard cases at a comfortable working height without needing a separate table or placing the case on uneven ground. The design focuses on improving ergonomics, portability, stability, and quick setup for users in field environments such as photography, hunting, and maintenance. Through customer research, concept development, prototyping, analysis, and testing, the final system was designed to support a loaded hard case, provide height adjustability, remain stable on uneven terrain, and be deployed by a single user in under five minutes. The final prototype demonstrates …

Formula Sae Planetary Gearbox Characterization Dynamometer, Trevor Marco Toma, Thomas Welden Pierce, Ethan Liu

Mechanical Engineering

This report outlines a custom hub motor dynamometer requested by the Cal Poly Racing FSAE team. The need for this testing platform is to characterize an existing Formula SAE planetary gearbox for a proposed 4WD powertrain. Hub motors, compact electric machines integrated directly into each outboard wheel, offer significant advantages in efficiency, traction, and chassis packaging compared to conventional RWD drivetrains. By mapping torque capacity, efficiency, lubrication method effectiveness, and fatigue life, the team can validate gearbox design and performance.

This senior project group designed and built a dynamometer according to these specifications which will allow for successful testing to …

Cosmetic Clamper, Daniel Peter Gates, Bruno Roberto Martinez, Samantha Remy, Zachary Joseph Roeber

Mechanical Engineering

Cosmetic Clamper Mechanical Engineering Senior Project was a senior project at California Polytechnic State University, San Luis Obispo in the College of Engineering, Mechanical Engineering Department. The project ran from September 2025 to June 2026. The project developed the Cosmetic Clamper device, an accessibility product designed to help individuals with unilateral upper extremity motor deficits open, use, and close cosmetic containers independently.

Me3329 Modular Phonograph Gearbox, Garrett Andrik Leighton, Preston Robert Hupe, Gavin Carter Ebner, Andrew Renato Reyes

Mechanical Engineering

The Mechanical Engineering Department at California Polytechnic State University, San Luis Obispo (Cal Poly), seeks to develop a laboratory tool allowing students to reinforce concepts of gears for Mechanical Systems Design (ME329). Some current laboratories do not provide students with hands-on interaction, and the department lacks equipment and documentation to support a standardized lab. With ME329 expanding from ten to fifteen weeks, there is an opportunity to create a physical gearbox design lab allowing students to reinforce lecture material in engaging ways, while standardizing student learning. This senior project is presented and sponsored by Professor Alan Zhang. It will be …

Raytheon Rtx Autonomous Vehicle Competition (Avc) - Unmanned Ground Vehicle (Ugv), Bryant Jonathan Martinez-Bautista, Geovanni Lara, Jared Herrera, Jose Barrera

Mechanical Engineering

Raytheon RTX has four universities participating in a competition to successfully complete various challenges with a UAV and UGV including navigation and landing. The students must work collaboratively to integrate and manufacture a working UGV that is compatible with the UAV.

Our sponsor is Raytheon, more specifically Mr. Luis Esparza. Important stakeholders also include Cal Poly and the entire team of ME & CPE working on the project. Raytheon and Luis are looking for innovative solutions that can be applied for real world scenarios where UAV’s and UGV’s are applied. Cal Poly is gaining recognition, and the team is gaining …

Semi-Automated Wine Barrel Filler, Elliot Jason Dejong, Carlo Caesare Deianni, Brady Emerson J. Leib

Mechanical Engineering

The proposed project is a semi-automated wine barrel filler. Currently, there is no streamlined and affordable method for smaller wineries to fill wine barrels without dedicating complete focus to the task. The primary use is controlled filling for white wine fermentation, during which an air gap must be left in the barrel to allow for expansion of the wine during fermentation. Tom Greenough, Saucelito Canyon’s head winemaker, and associate winemaker Bodie Ringhofer are the primary stakeholders in our project and want to consistently fill barrels at their winery to a fluid volume of approximately 50 gallons each. This project serves …

Me Department Bespoke Coffee Cabinet, Mickie Clyne, Stephen Tamacheepjaroen, Samuel Johnson, Willem Gray

Mechanical Engineering

This senior project involved the design, fabrication, and testing of a custom coffee cabinet for the California Polytechnic State University Mechanical Engineering Department. The project addressed challenges associated with appliance organization, storage efficiency, accessibility, and maintenance within the department’s shared breakroom space. A human-centered design process was used to identify stakeholder needs and develop engineering specifications for the final product.

The completed cabinet integrates custom woodworking, steel pipe frame construction, dedicated K-Cup storage, organized appliance placement, and a rack-and-pinion sliding platform that improves access to the Keurig coffee maker for refilling and maintenance. Design decisions were informed through stakeholder feedback, …

Implementation Of A Line-Scan Camera Triangulation Sensor For A Ball Balancer, Jackson R. Mclaughlin

Master's Theses

Ball Balancer or Ball on Plate systems are used for education and research in control theory. These consist of a plate which can be actively tilted, with a ball rolling on the surface. Students are challenged to model the dynamics of the system and implement a control loop which is capable of stabilizing the ball by actuating the plate.  The mechatronics group at Cal Poly is developing hardware for one of these ball-balancer systems, for future use in the Mechanical Engineering curriculum.

The position of the ball relative to the plate must be measured in order to control and stabilize …

Multi-Ton Bin Transport Device, Cole Kramer, Ruth Stirrup, Fabian Ruiz, Daniel Ramirez

Mechanical Engineering

This project sought to solve a problem at the Water Resource Recovery Facility in San Luis Obispo with the transportation of multi-ton bins on-site. Their current solutions prove ineffective, as they damage their equipment and the concrete pad, as well as pose major safety risks to the operators moving these bins. The Facility requires the bin transport design to be low-cost, effective, and without risk of damage to the bins or surroundings, while maintaining the integrity of the bins. This project presents a conceptual design that is similar to a scissor lift, integrated into a trailer which will connect to …

Foldable Transfer Platform, Toby Sagi, Ashton Heiati, Triton Johnson, Zachary Denis

Mechanical Engineering

The report details the design and results of a Hoyer lift to transfer patients between wheelchairs and our sponsor's, Beacon VTC Santa Maria, vans. The lift disassembles into 3 main pieces, allowing the lift to be stored in the back of the van. The lift uses a hydraulic actuator to rotate the boom. We handed over our project to Beacon VTC Santa Maria for use in their facility!

Hpv Speed Bike Landing Gear, Nathan Walker, Dylan Hyde, Mark Spohn, Trey Barber

Mechanical Engineering

This report presents the development of a retractable landing gear system for Cal Poly’s human-powered speed bike. The system is designed to support the bike during low-speed operation, especially during launch, when the vehicle is unstable and typically requires assistance from a support crew. The landing gear uses spring-driven extensions controlled by handlebar-mounted Bowden cables, allowing the rider to retract the system while maintaining control of the bike. By fitting within the fairing and retracting after launch, the design aims to improve takeoff stability and rider safety while preserving the aerodynamic performance required for high-speed competition.

Bonderson Workbench, Han Xu, Aidan Robleto, Sean Murphy, Victor Duran

Mechanical Engineering

This project redesigns the existing creative workbenches in Cal Poly's Bonderson High Bay to improve mobility and functionality for students and staff in the Mechanical Engineering Department.

Fsae Bespoke Brake Calipers For Hub Motor Architecture, Connor William Vaughan, Liam Upton Walsh, Bradley Brian Kern

Mechanical Engineering

Brakes are the most critical safety system on any performance vehicle, and as Cal Poly Racing transitions their Formula SAE car from a single rear motor to a four-in-wheel motor setup with regenerative braking, the team identified an opportunity to develop a bespoke brake caliper tailored to their specific needs. This document outlines the research, design, manufacturing, and validation of custom front brake calipers designed to improve upon commercial motorcycle calipers in key areas such as serviceability, mounting rigidity, thermal behavior, mass, and hub motor integration. The resulting design is a two-piece, four-piston, radially-mounted aluminum caliper featuring titanium pistons, toolless …

Baja Sae Gear Testing, Selina Bayles, Lucia Giacalone, Claire Cornelsen, Sarah Talbert

Mechanical Engineering

The Baja SAE Gear Testing project outlined a test stand and procedure to update the S-N curve currently used by the Baja SAE team. Currently the Cal Poly Baja SAE geartrain team uses a S-N curve to design custom gears, but this S-N curve does not accurately reflect the gears uses and their fatigue life. This project outlines the exploration of a dyno set up to allow for future testing of different categories of short life cycle gears to collect data and generate a new S-N curve and, ultimately, update the design of the gears. This team created a dyno …

Multi-Cater Pack Heat Sealer, Ivan Medina-Zepeda, Laurent Hirakata, Donovan Furtado, Cody Ngan

Mechanical Engineering

The Multi-Cater Pack Heat Sealer was developed to support Achievement House, a non-profit organization that employs adults with intellectual and physical disabilities and is facing increasing demand for sealed cater packs. Existing single-pack sealers limited both throughput and accessibility, which led to the creation of a 3D printed attachment for a 40-inch impulse heat sealer. The attachment allows nine packs to be sealed at the same time and includes a tray-style trapdoor that allows for quick unloading. The need for accessibility and usability guided the design throughout the process. Alignment guides improve placement consistency, and the ergonomic layout accommodates both …

Design Of Ballistic Armor Using Multi-Composite Sandwich Structures With Nanomaterial Additives, Carmen Alaichamy

College of Engineering Summer Undergraduate Research Program

This study explores the bulletproof capabilities of Kevlar composites fabricated using advanced additive manufacturing techniques. Continuous fiber reinforced 3D printing (CFRP) is employed to produce Kevlar-reinforced polymer matrix composites (PMCs) with optimized structural configurations for ballistic protection. The primary objective is to evaluate the impact resistance of these composites against 9mm projectiles through systematic experimental testing. A series of ballistics tests are conducted using a high-velocity gas-gun system to fire 9mm projectiles at varying speeds angles. The tests will be conducted at the San Luis Obispo Range, with projectiles fired at various angles. The effects of fiber volume fraction, reinforcement …

Leveraging Smartphones For Balance Assessment, Kelly Graham

College of Engineering Summer Undergraduate Research Program

Assessment of human balance provides valuable metrics to track the health, development, and fall risk of individuals. The prominent method for objective balance assessments has used force plates to track the center of pressure (COP) position as a participant attempts to balance during varying tasks. However, the use of force plates is limited by the cost of equipment and expertise required, leading to recent interest in using embedded inertial measurement units (IMUs) in mobile devices instead. Many researchers have explored placing mobile devices close to the subject’s center of mass (COM) to approximate the subject’s COM acceleration and using the …

Integration And Testing Of A Quadruped Robot With Ros2, Jeremy S. West

Master's Theses

The Cal Poly Legged Robotics Group has been developing research and teaching platforms for agile legged robotics since 2020. These platforms are expected to provide students with opportunities to develop complete legged-robot systems from low-level control to advanced robotics tasks such as motion planning and decision making. However, the current prototyped quadruped robot lacked the software and sensing capabilities for high-level quadrupedal gaits and advanced robotic research.

To address these challenges, this project developed Switch, a robotic platform that builds upon the previous BRUCE platform with significant hardware and software upgrades. Switch features a modular design that allows individual software …

Efficient Thermal Design Of Data Centers, Keats M. Baggett, Andrew Ergood, Colin Brace, Jack Zilligen

Mechanical Engineering

Our sponsor needs a way to categorize and quantify the top 3 colocation center sites based on a series of criteria for given power specs. The sponsor also needs a single innovative cooling method to meet thermal and power requirements while also being manufacturable at scale. This device must also be able to interact with the given Colocation Heating Ventilation and Air Conditioning (HVAC) system. This design will be tested to provide insight and data that will be applicable to further the development of colocation center cooling. This project will be executed by the Cal Poly senior project team and …

Van Accessibility, Ann Larson, Camelia Anne Noureddine, Stephanie Rose Ruzicka, Kayla Joanne Gowey

Mechanical Engineering

The SLO Achievement House provides resources and activities for their clients, including daily trips to different parts of the community, to keep their clients connected to society. These trips require the clients, many of whom struggle with general mobility and strength, to step up to the high entrance of a van or company car. This daily activity poses a challenge both physically and emotionally for the clients. The current solution utilizes commercially available step stools, which lack handrails, overall stability, and adequate step depth. The Achievement House needs a stool or ramp tailored to their client’s needs and their specific …

Uv Vessel Hoist Scope Of Work, Quinn J. Horak, Harvey Perkins, Andrew A. Osborn, Mikayla H. Nieman

Mechanical Engineering

The San Luis Obispo Wastewater Treatment Plant uses ultraviolet (UV) tubes to purify water. These tubes are cleaned by an internal wiping mechanism that must be removed for servicing and replacing damaged tubes. Currently, this is accomplished by using an engine hoist, but this method requires a large amount of effort and is not safe. Technicians have requested a new method of lifting wiper mechanisms that is safer, faster, and easier to use than their current method.

To solve this problem, we have developed a design that consists of a custom gantry crane with a hoist on a trolley. The …

Brush Seal Cycling Test Rig, Angelo J. Reis, Neil M. Bedagkar, Max A. Soury, Eoin K. Lenham

Mechanical Engineering

To prevent backflow from the high pressure compressor stages of their gas turbines to lower pressure regions, Solar Turbines utilizes brush seals along their driveshafts. Due to manufacturing limitations, no shaft is perfectly symmetric about its rotating axis, leading to orbiting that creates asymmetric friction on the shaft through rubbing. With this biased application of friction comes a hotspot on one side of the shaft, causing bowing of the shaft and cascading into an amplified vibrational response. Our goal is to gather data on this phenomenon and offer a potential solution.

2024-2025 Cal Poly Fluid Power Vehicle Competition Team, Jaskaran Singh Hothi, Justin Menzie Lesko, Tristan Kai Crawford, Lucas Rupert Erickson, Diego Velazquez

Mechanical Engineering

The Fluid Power Vehicle Challenge (FPVC) provides an avenue for the exploration of fluid-powered transportation, adhering to regulations set by the National Fluid Power Association (NFPA). This document serves as a roadmap for our team’s research, design, and manufacturing of a vehicle for participation in the FPVC. The team’s journey began with extensive background research, encompassing stakeholder engagement, analysis of existing solutions, and education on fluid power fundamentals. From this information, we decided to focus on enhancing mechatronics systems, improving the transmission, optimizing the mounting, adding a pneumatic element, and improving the efficiency of the hydraulic system of the vehicle …

Hi-Trac Camera Jig, Gabriel Frank Junge, Josh Sherreitt, Jake Weiser, Luke Silver

Mechanical Engineering

Uranium fuel assemblies are stored upright in an underwater container inside the spent nuclear energy fuel pool at Diablo Canyon. The engineers and in-service-inspection team all work together to safely locate this container inside the pool on pins so it is guaranteed safe before they begin loading it with spent uranium fuel rods. The Operators currently employ the use of a zip-tied camera jig that is lowered into the pool along with the tank (called a HI-TRAC) to ensure it is oriented correctly in the pool. This camera jig is in desperate need of re-vamping and re-designing to optimize efficiency …

Design Principles For Robotic-Controlled 3d Printing Of Soft Tissue-Mimicking Materials, Karina Mealey

Master's Theses

Geometrically and physically accurate 3D models are emerging as essential tools for surgeons in pre-operative planning and training, but current methods of producing these models are not sufficient. Existing solutions have downsides such as high costs, long and tedious production times, high complexity resulting in a lack of scalability, or an inability to meet material requirements for accurately simulating human tissue.

The objective of this work is to develop principles for a low-cost, easy-to-use 3D printing system capable of prototyping with soft tissue-mimicking materials. To pursue this goal, a MyCobot280 robot arm was used as the mechanism to explore the …

Floating Wind Turbine Foundation, Clayton Lahodny, Dillon Nelson, Trevor Ortega, Andrew Cervantes

Mechanical Engineering

The 2024 Collegiate Wind Competition (CWC) has introduced a new element to their Turbine Design Competition: a floating foundation. In previous years, foundations have been fixed-bottom in a box of sand and water. The Cal Poly Wind Power Club, who competes in the CWC every year, requires a floating foundation to be designed, manufactured, and tested to assist in winning the competition. The foundation is a large, hollow, cylindrical barge with a hanging spar (heavy mass). The barge will provide a restoring moment using buoyancy, and the heavy spar provides additional restoring moment. Four cables will be attached at the …

Scitechatorium, Olivia Lafferty, Yvonne Brien Miller, Colton Swinth, Savannah Pinheiro, Gage Heinze

Mechanical Engineering

Bellevue Santa-Fe Charter School (Bellevue) is a K6th grade public charter elementary school in Avila Beach, California. The primary focus at Bellevue is fostering unique learning experiences, empowering students through project-based learning, and engaging students in creative endeavors. Following these themes, the school has allocated space and funding for an on-campus science and technology museum known as the SciTechatorium. The museum is currently open during students’ lunch period, providing interactive displays on concepts in human biology, nature and wildlife, physics, and electronics. Bellevue’s K-6th grade science teacher, Christian Strauli, and Bellevue parent volunteers are primarily responsible for the museum’s upkeep …

License To Drill, Gabrielle Noemi Orlando, Alexcias Olga Meeks, Dayana Guadalupe Gonzalez, Mark Dahmen

Mechanical Engineering

The goal of this project is to provide the student machine shops with an updated License to Drill (LTD) certification training, formally known as the Red Tag. The current training has two key components: a preliminary Canvas course and an in-person training with a safety tour, safety quiz, and a hands-on project. Currently, the hands-on project is outdated and unengaging. Thus, the primary focus is to replace it with an inspiring and memorable project, which includes written and visual instructional content on how to make it. The Canvas will thus be updated, a new instructional video will be created, and …

Lidss Raft Battery Pack Integration, Jack Maxwell, Vincent Stevens, Matthew Hoodmaker, Colin Flanders

Mechanical Engineering

Lawrence Livermore National Laboratory is a critical member of the United States Department of Defense. Their Independent Diagnostics Scoring System (LIDSS) uses rafts that operate in the ocean to collect missile test data. Several times a year, the United States will test their Inter-Continental Ballistic Missiles by launching them into the ocean near the Marshall Islands. This is where the LIDSS rafts collect their test data. Our project was centered around re-designing the battery pack used by the rafts. The current battery pack design experiences water ingress problems and is difficult to access. Our re-designed battery pack is waterproof to …

Design, Fabrication, And Testing Of A Dual-Rate Spring System For Mountain Bike Frames, Lucas P. Grizzle

Master's Theses

The design of full-suspension mountain bikes is a careful balance of suspension kinematics, structural dynamics, and manufacturing optimization for the expected use case. A bike designed to excel in one area will likely exhibit reduced performance in others. This optimization problem is addressed by designing, integrating, and testing a dual-rate spring system within a fully custom frame. The dual-rate spring is fully decoupled from the rest of the suspension kinematics, providing designers with an additional parameter to achieve ideal suspension behavior. This is accomplished by placing a thermoplastic polyurethane (TPU) bushing in series with the rear shock. The influence of …