Manufacturing Commons^™

A Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming Leu, Gregory Hilmas

Faculty Publications, Mechanical Engineering

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content (<1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Mechanical Testing Of Fused Filament 3-D Printed Components For Distributed Manufacturing, Nagendra Gautam Tanikella

Dissertations, Master's Theses and Master's Reports

Fused filament fabrication (FFF)-based open-source 3-D printers offer the potential of decentralized manufacturing both in developing and developed countries. Unfortunately, a severe lack of data and standards relating to material properties and printed components limit this potential. This thesis first investigates the mechanical properties of a wide-range of FFF materials and provides a database of mechanical strength of the materials tested. The results demonstrate that the tensile strength of a 3-D printed specimen depends largely on the mass of the specimen, which provides a means to estimate the strength of 3-D printed components. Then this information is used to evaluate …

Cryogenic Processing Of Al 7050-T7451 Alloy For Improved Surface Integrity, Bo Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Al 7050-T7451 alloy with good combinations of strength, stress corrosion cracking resistance and toughness, is used broadly in the aerospace/aviation industry for fatigue-critical airframe structural components. However, it is also considered as a highly anisotropic alloy as the crack growth behavior along the short transverse direction is very different from the one in the long transverse direction, due to the inhomogeneous microstructure with the elongated grains distributed in the work material used in the sheet/plate applications. Further processes on these materials are needed to improve its mechanical and material properties and broaden its applications.

The material with ultra-fine or nano …

Fatigue Properties Of Magnetorheological Elastomers And The Design Of Interfacial Layers To Improve Fatigue Life., Yanfen Zhou

Doctoral

The primary aim of this PhD programme was to understand the fatigue behaviour of magnetorheological elastomers (MREs) and provide a reliable fatigue life predictor for this class of materials. To realise this aim required the study of the dynamic behaviour of MREs using the equi-biaxial bubble inflation test method. Isotropic and anisotropic MREs were fabricated from silicone rubber (SR) filled with soft carbonyl iron (CI) particles. The equi-biaxial fatigue behaviour of these samples was determined using a bubble inflation method. Wohler (S-N) curves for both isotropic and anisotropic MREs were produced by subjecting the compounds to cycling over a range …

Modeling And Simulation Of Micro Electrical Discharge Machining Process, Bai Shao

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Micro parts and systems are playing crucial roles in the area of semiconductor, biomedical device, micro fluid devices, automotive, aerospace and so forth. Micro manufacturing is one of the most important technologies in realizing miniaturization. Compared to other micro manufacturing methods, micro-EDM is drawing lots of attention due to its ability to machine complex 3D parts regardless of the hardness of the workpiece material.

Micro-EDM is the cumulative result of numerous single discharges; therefore, it is crucial to understand the single discharge material removal process in micro-EDM. However, due to the stochastic nature and complex process mechanism, micro-EDM, including its …

Process Development For Compression Molding Of Hybrid Continuous And Chopped Carbon Fiber Prepreg For Production Of Functionally Graded Composite Structures, Corinne Marie Warnock

Master's Theses

Composite materials offer a high strength-to-weight ratio and directional load bearing capabilities. Compression molding of composite materials yields a superior surface finish and good dimensional stability between component lots with faster processing compared to traditional manufacturing methods. This experimental compression molding capability was developed for the ME composites lab using unidirectional carbon fiber prepreg composites. A direct comparison was drawn between autoclave and compression molding methods to validate compression molding as an alternative manufacturing method in that lab. A method of manufacturing chopped fiber from existing unidirectional prepreg materials was developed and evaluated using destructive testing methods. The results from …

Microstructure And Property Of Tib-Reinforced Ti Alloy Composites By Laser Metal Deposition, Yunlu Zhang, Jingwei Zhang, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

TiB-reinforced Ti alloy composites have been laser deposited with pre-alloyed Ti-6Al4V-1B powder. The microstructure of the as-deposited and heat treated composites have been characterized in detail using scanning electron microscope (SEM). A homogeneous dispersion of needle-like TiB precipitates is formed in the Ti-6Al-4V α/β matrix. TiB precipitates promote formation of small near equaxed α/β grain after β annealing process. The micro-hardness of the laser deposited composites increase 20-30% with 5 vol. % TiB precipitates compared to unreinforced Ti-6Al-4V deposits.

Effects Of Temperature On Aqueous Freeform Extrusion Fabrication, Jie Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An experimental study was conducted to investigate the effect of temperature on ceramic parts produced by paste extrusion based additive manufacturing followed by sintering. A computer-controlled gantry system equipped with a piston extruder was used to extrude aqueous alumina paste. The system includes a temperature control subsystem that allows for freeform extrusion fabrication inside a low-temperature (<0°C) chamber. It can also be used for fabricating parts on a hot plate at ambient or higher temperatures (≥20°C). Test specimens were fabricated from aqueous aluminum pastes at -20°C in the low-temperature chamber and also on the hot plate at 40°C. The minimum angles achievable by these two processes for part fabrication, without use of support material, were compared. Also compared were the relative density and mechanical properties of the parts obtained after sintering. Microstructures were examined via scanning electron microscopy in order to obtain a deeper understanding of the effect of fabrication temperature.

Laser Metal Deposition Of Functionally Gradient Materials From Elemental Copper And Nickel Powders, Sreekar Karnati, Todd E. Sparks, Frank W. Liou, Joseph William Newkirk, Karen M. Brown Taminger, William J. Seufzer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This work deals with the planning and fabrication of a functionally gradient copper-nickel composition via Laser Metal Deposition (LMD). Various compositions of copper and nickel were made by blending different weight percentages which were then sequentially deposited to fabricate functionally gradient copper-nickel thin-wall structures. Analyses were performed by sectioning the thin-wall samples for metallographic, hardness, X-ray diffraction (XRD) and Energy Dispersive X-ray Spectroscopy (EDS) studies. The fabrication was studied for identifying and corroborating the deposited compositions and their corresponding gradients. XRD analyses were performed to identify the crystal structure of the deposit. EDS analysis was instrumental in identifying the variation …

A Microstructure And Hardness Study Of Functionally Graded Materials Ti6al4v/Tic By Laser Metal Deposition, Jingwei Zhang, Yunlu Zhang, Frank W. Liou, Joseph William Newkirk, Karen M. Brown Taminger, William J. Seufzer

Materials Science and Engineering Faculty Research & Creative Works

Crack free functionally graded material (FGM) Ti6Al4V-TiC has been fabricated by laser metal deposition (LMD) using TiC and Ti6Al4V powder which were premixed for different ratios. This study focuses on the influence of laser processing parameters and TiC compositional distribution on microstructure, Vickers hardness and phase. The microstructure is analyzed by scanning electron microscopy (SEM), x-ray diffraction (XRD) and hardness tests. Primary carbide, eutectic carbide and unmelted carbide are found in the deposit area. When laser power increased, the primary and secondary dendrite arm spacing increased. The laser power and scanning speed did not influence the Vickers hardness distribution significantly.

Freeform Extrusion Fabrication Of Titanium Fiber Reinforced Bioactive Glass Scaffolds, Albin Thomas, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Although implants made with bioactive glass have shown promising results for bone repair, their application in repairing load-bearing long bones is limited due to their low fracture toughness and fairly fast degradation response in vivo. In this paper, we describe our investigation of freeform extrusion fabrication of silicate based 13-93 bioactive glass scaffolds reinforced with titanium fibers. A composite paste was prepared with 13-93 bioactive glass filled with titanium fibers (~16 µm in diameter and aspect ratio of ~250) having a volume fraction of 0.4 vol. %. This paste was then extruded to fabricate scaffolds with an extrudate diameter …

Methods Of Extrusion On Demand For High Solids Loading Ceramic Paste In Freeform Extrusion Fabrication, Wenbin Li, Amir Ghazanfari, Ming Leu, Robert Landers

Faculty Publications, Mechanical Engineering

Fabrication of highly dense parts with complex geometry by paste-extrusion-based solid freeform fabrication processes requires a precise control of the extrusion flow rate to dispense material on demand, which is often referred as Extrusion-On-Demand (EOD). The extrusion process for aqueous ceramic pastes is complex and difficult to control due to their non-Newtonian behavior, compressibility and inhomogeneity. In this study, three methods of EOD (based on ram extruder, needle valve, and auger valve) are introduced and investigated for the extrusion of high solids loading (i.e., >50%, volumetric) aqueous alumina paste. Optimal extrusion process parameters for these methods are determined through printing …

Size Effects In Human Visual Inspection For Micro/Meso Scale Parts, Sri Harsha Kavuri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Visual inspection has been a major method of quality control in conventional manufacturing processes for the last fifty years. Utilizing trained human inspectors to perform this visual inspection has been the most effective means of maintaining quality control. Extensive research has been performed to understand the factors that influence the human inspection process.

In the recent years, there has been a significant emphasis on manufacturing at the smaller end of the size-spectrum such as Micro and Meso scale manufacturing. Quality control at becomes a challenging task due to the extremely small sizes. Several automated visual inspection techniques have been proposed …

Engineered Surface Properties Of Porous Tungsten From Cryogenic Machining, Julius M. Schoop

Theses and Dissertations--Chemical and Materials Engineering

Porous tungsten is used to manufacture dispenser cathodes due to it refractory properties. Surface porosity is critical to functional performance of dispenser cathodes because it allows for an impregnated ceramic compound to migrate to the emitting surface, lowering its work function. Likewise, surface roughness is important because it is necessary to ensure uniform wetting of the molten impregnate during high temperature service. Current industry practice to achieve surface roughness and surface porosity requirements involves the use of a plastic infiltrant during machining. After machining, the infiltrant is baked and the cathode pellet is impregnated. In this context, cryogenic machining is …

Laser Surface And Sub-Surface Repair During Metal Additive Manufacturing, Prudvi Teja Ravi

Masters Theses

"This study examines the use of laser surface treatment to repair surface and subsurface defects. Numerical analysis was performed on laser surface melting using Gaussian heat distribution equations to analyze the depth of the melt pool created by the phenomena. Concurrently, a process map was developed with a planned set of experiments by varying the ranges of laser power and travel speed to determine the dimensions of the melt pool across the gamut. The data generated from both the process studies and the numerical analysis was then used to determine the ideal operating ranges of the process parameters to repair …

Biphilic Nanoporous Surfaces Enabled Exceptional Drag Reduction And Capillary Evaporation Enhancement, Xianming Dai, Fanghao Yang, Ronggui Yang, Xinyu Huang, William A. Rigdon, Xiaodong Li, Chen Li

Faculty Publications

Simultaneously achieving drag reduction and capillary evaporation enhancement is highly desired but challenging because of the trade-off between two distinct hydrophobic and hydrophilic wettabilities. Here, we report a strategy to synthesize nanoscale biphilic surfaces to endow exceptional drag reduction through creating a unique slip boundary condition and fast capillary wetting by inducing nanoscopic hydrophilic areas. The biphilic nanoporous surfaces are synthesized by decorating hydrophilic functional groups on hydrophobic pristine multiwalled carbon nanotubes. We demonstrate that the carbon nanotube-enabled biphilic nanoporous surfaces lead to a 63.1% reduction of the friction coefficient, a 61.7% wetting speed improvement, and up to 158.6% enhancement …

A Collagen‐Glycosaminoglycan‐Fibrin Scaffold For Heart Valve Tissue Engineering Applications, Claire Brougham, Stefan Jockenhoevel, Thomas Flanagan, Fergal O'Brien

Conference Papers

The field of heart valve biology and tissue engineering a heart valve continue to expand. The presentatio ns at this meeting reflect the advances made in both areas due to the multi-disciplinary approach taken by many laboratories.

Microstructure Development Of Granular System During Compaction, Chen Shang, Marcial Gonzalez

The Summer Undergraduate Research Fellowship (SURF) Symposium

Granular materials is the second most manipulated material in the industry today. They are easy to transport and more and more newly developed materials cannot stand the process of traditional casting, like energetic materials and bio-materials, but will survive the powder compaction process. Having a better understanding of the microstructure development of granular systems during compaction process, especially for particles that will heavily deform under loading, will give an insight of how to better process the powders to produce materials with overall better performance comparing to bulk materials. The main theory and mechanism applied are Hertz law and nonlocal contact …

In Vitro Assessment Of Laser Sintered Bioactive Glass Scaffolds With Different Pore Geometries, Krishna C. R. Kolan, Albin Thomas, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The pore geometry of bioactive glass scaffolds intended for use in bone repair or replacement is one of the most important parameters that could determine the rate of bone regeneration. The pore geometry would also affect the mechanical properties of the scaffolds and their rate of degradation. Scaffolds with five different architectures, having ~50% porosity, were fabricated with silicate (13–93) and borate (13–93B3) based bioactive glasses using a laser sintering process. An established, late-osteoblasts/early-osteocytes cell line was used to perform cell proliferation tests on the scaffolds. The results indicated that the cells proliferate significantly more on the scaffolds which mimic …

A Mechanical Testing Methodology For Additive Manufacturing Processes, Sujitkumar Dongare, Todd E. Sparks, Joseph William Newkirk, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Most additive manufacturing processes are layer-by-layer deposition, thus its mechanical properties could be very different than those made from traditional manufacturing processes. This paper summarizes a mini-tensile testing methodology for additive manufacturing. Research concerning the tensile testing of metallic material has been conducted and test methods have been defined. It encompasses the methods for determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area. The study of positional variation and cooling-rate dependency in case of additive manufacturing proves to be expensive and time consuming with the full-size test specimens. Thus, this paper discussed a technique for …

Investigation Of Forged-Like Microstructure Produced By A Hybrid Manufacturing Process, Romy Francis, Joseph William Newkirk, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser Metal Deposition (LMD) is an additive manufacturing technique for manufacturing complex near net shaped components. The grain size of the typical deposition microstructure in case of Ti-6Al-4V can range between 100µm-600µm, which is much larger than that of forged-like microstructures. Friction Stir Processing (FSP) has been investigated as a method for surface modification to form refined microstructure at the surface of the Ti-6Al-4V components manufactured from the LMD method. Integration of FSP and LMD can greatly improve the product properties. Friction stir processing of the laser deposited Ti-6Al-4V deposits was performed and optimum processing parameters were obtained using this …

Stress Analysis For Chip Scale Packages With Embedded Active Devices Under Thermal Cycling, Hyunwook Yeo

Dissertations and Theses

One of the main challenges in the electronics manufacturing and packaging development is how to integrate more functions inside the same or even smaller size. To meet the demand for higher integration, the interest toward passive and active component embedding has been increasing during the past few years. One of the main reasons for the growing interest toward embedded active components, in addition to demand for higher packaging density, is the need for better electrical performance of the component assemblies. However, it is little known how embedded IC and passives affect the reliability of IC packaging.

Solder joints have been …

3d Printing Of Stainless Steel For Engineering Applications, Michael Doyle

Undergraduate Research Symposium

3-D metal printing has the potential to solve problems in the medical, prototyping, automotive, aerospace, defense, and other engineering industries. To reach the potential of any manufacturing process, the final product’s material characteristics and how the process affects those characteristics must be understood to meet the demands of industrial applications. There is a gap in standard testing information regarding metal based 3-D metal printing processes. The purpose of this research is to fill that gap of valuable information for this manufacturing process, so that its principles can be used to design better products. Fundamental tensile and compression tests were executed …

Shape Memory Behavior Of Single And Polycrystalline Nickel Rich Nickel Titanium Alloys, Irfan Kaya

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTi is the most commonly used shape memory alloy (SMA) and has been widely used for bio-medical, electrical and mechanical applications. Nickel rich NiTi shape memory alloys are coming into prominence due to their distinct superelasticity and shape memory properties as compared to near equi-atomic NiTi shape memory alloys. Besides, their lower density and higher work output than steels makes these alloys an excellent candidate for aerospace and automotive industry. Shape memory properties and phase transformation behavior of high Ni-rich Ni₅₄Ti₄₆ (at.%) polycrystals and Ni-rich Ni₅₁Ti₄₉ (at.%) single-crystals are determined. Their properties are sensitive …

Precipitation, Orientation And Composition Effects On The Shape Memory Properties Of High Strength Nitihfpd Alloys, Emre Acar

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf high temperature shape memory alloys are attractive due to their high operating temperatures (>100 ^oC) and acceptable transformation strain compared to NiTi. However, NiTiHf has limitations due to their lack of ductility and low strength, resulting in poor shape memory properties. In this study, Pd has been added to NiTiHf alloys in an attempt to improve their shape memory behavior. A combined approach of quaternary alloying and precipitation strengthening was used.

The characterization of a Ni_45.3Ti_29.7Hf₂₀Pd₅ (at. %) polycrystalline alloy was performed in compression after selected aging treatments. Transmission electron …

Investigation Of Thermal Cycle And Hardness Distribution In The Laser Cladding Of Aisi H13 Tool Steel Produced By A High Power Direct Diode Laser, Parisa Farahmand, Prabu Balu, Fanrong Kong, Radovan Kovacevic

Mechanical Engineering Research

Laser cladding (LC) of tool steel has significant application in rapid tooling, and surface coating for worn-out components in different industries. During the LC process, several phase transformations influence the microstructural and mechanical properties of the deposited layer. In order to successfully implement the LC process, it is essential to understand the relationship between the thermal cycle (heating and cooling), phase transformations, and the output quantities of the deposited layer. In this study a direct diode laser with a power of up to 8 kW was used to deposit AISI H13 tool steel on mild steel grade A36 substrate to …

Effect Of Architecture And Porosity On Mechanical Properties Of Borate Glass Scaffolds Made By Selective Laser Sintering, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Taylor Comte

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The porosity and architecture of bone scaffolds, intended for use in bone repair or replacement, are two of the most important parameters in the field of bone tissue engineering. The two parameters not only affect the mechanical properties of the scaffolds but also aid in determining the amount of bone regeneration after implantation. Scaffolds with five different architectures and four porosity levels were fabricated using borate bioactive glass (13-93B3) using the selective laser sintering (SLS) process. The pore size of the scaffolds varied from 400 to 1300 μm. The compressive strength of the scaffolds varied from 1.7 to 15.5 MPa …

Probabilistic Simulation Of Solidification Microstructure Evolution During Laser-Based Metal Deposition, Jingwei Zhang, Frank W. Liou, William Seufzer, Joseph William Newkirk, Zhiqiang Fan, Heng Liu, Todd E. Sparks

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A predictive model, based on a Cellular Automaton (CA) - Finite Element (FE) method, has been developed to simulate microstructure evolution during metal solidification for a laser based additive manufacturing process. The macroscopic FE calculation was designed to update the temperature field and simulate a high cooling rate. In the microscopic CA model, heterogeneous nucleation sites, preferential growth orientation and dendritic grain growth kinetics were simulated. The CA model was able to show the entrapment of neighboring cells and the relationship between undercooling and the grain growth rate. The model predicted the dendritic grain size, structure, and morphological evolution during …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …