Manufacturing Commons^™

Deformation And Stress Control Study On H-Beam Welded By Ultra High-Strength Steel, Zhaoxia Qu, Xiaojie Wang, Liqian Xia, Zhongqu Sun

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modeling And Simulation Of Dendrite And Porosity Evolution During Solidification In The Molten Pool Of Al–Cu Alloys, Cheng Gu, Yanhong Wei, Xiaohong Zhan

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Study On Growth Model Of Cellular Automata Method In Solidification Simulation, Zhao Guo, Jian-Xin Zhou, Ya-Jun Yin, Chang-Chang Liu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Fe Simulation For Accuracy Evolution And Control In Hot Forging Of Non-Circular Spur Bevel Gear, Wuhao Zhuang, Xinghui Han

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Calphad-Based Materials Genome And Its Applications To Additive Manufacturing, Wei Xiong

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Recent Advances In Four-Dimensional Studies Of Advanced Materials And Processing, Jiawei Mi

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Flow Stress And Microstructure Models Of Alloys, Lars-Erik Lindgren

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Investigation Of Heat-Affected 304l Ss Powder And Its Effect On Built Parts In Selective Laser Melting, Caitlin S. Kriewall, Austin T. Sutton, Ming-Chuan Leu, Joseph William Newkirk, Ben Brown

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective laser melting (SLM) is a powder bed based additive manufacturing process in which a layer of powder is laid over the surface of a substrate and a laser with sufficient energy is employed to selectively melt particles to build a part layer by layer. During the SLM process, dark smoke was observed coming off of the powder bed surface where the laser was interacting with powder. This phenomenon resulted from heat-affected powder that was visibly different than the base powder. Since the concentration of the heat-affected powder differs throughout the build chamber as a result of the recirculating argon …

A Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Properties Of Partially Stabilized Zirconia Components Fabricated By The Ceramic On-Demand Extrusion Process, Wenbin Li, Amir Ghazanfari, Devin Mcmillen, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Ceramic On-Demand Extrusion (CODE) process is a novel additive manufacturing process for fabricating dense ceramic components from aqueous pastes of high solids loading. In this study, 3 mol% Y₂O₃ stabilized tetragonal zirconia polycrystal (3Y-TZP) parts were fabricated using the CODE process. The parts were then dried in a humidity controlled environmental chamber and sintered under atmospheric pressure. Mechanical properties of the sintered parts were examined using ASTM standard test techniques, including density, Young’s modulus, flexural strength, Weibull modulus, fracture toughness and Vickers hardness. The microstructure was analyzed, and grain size was measured using scanning electron microscopy. …

Simulation Of Cooling Rate Effects On Ti-48al-2cr-2nb Crack Formation In Direct Laser Deposition, Lei Yan, Wei Li, Xueyang Chen, Yunlu Zhang, Joseph William Newkirk, Frank W. Liou, David Dietrich

Materials Science and Engineering Faculty Research & Creative Works

Transient temperature history is vital in direct laser deposition (DLD) because it reveals the cooling rate at specific temperatures, which directly relates to phase transformation and types of microstructure formed in deposit. FEA simulation was employed to study the transient temperature history and cooling rate at different experimental setups in Ti-48Al-2Cr-2Nb DLD process. In this paper, an innovative model was described, which combines a moving Gaussian distribution heat source and element birth and death technology in ANSYS, help to analysis cooling rate control method and guide crack-free deposits build process.

Elevated Temperature Microstructure Stability Of Slm 304l Stainless Steel, Tarak Amine, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

With time at temperature, changes in metallurgical structure can be expected for almost any steel or alloy. In stainless steels, the changes can be grain growth, carbide precipitation, ferrite decomposition, or embrittlement. These phenomena can significantly effect the properties of the steel and would potentially change the functionality of the component. Therefore, to determine component stability, the elevated temperature microstructure stability of additive manufacturing materials was studied. This work investigates the influence of different aging times of additive material stainless steels (304L) fabricated with the Selective Laser Melting (SLM) process on microstructure and mechanical properties. Microstructure and mechanical properties were …

3d Printing Of A Polymer Bioactive Glass Composite For Bone Repair, Caroline Murphy, Krishna C. R. Kolan, M. Long, Ming-Chuan Leu, Julie A. Semon, D. E. Day

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A major limitation of synthetic bone repair is insufficient vascularization of the interior region of the scaffold. In this study, we investigated the 3D printing of adipose derived mesenchymal stem cells (AD-MSCs) with polycaprolactone (PCL)/bioactive glass composite in a single process. This offered a three-dimensional environment for complex and dynamic interactions that govern the cell’s behavior in vivo. Borate based bioactive (13-93B3) glass of different concentrations (10 to 50 weight %) was added to a mixture of PCL and organic solvent to make an extrudable paste. AD-MSCs suspended in Matrigel was extruded as droplets using a second syringe. Scaffolds measuring …

Designed Extrudate For Additive Manufacturing Of Zirconium Diboride By Ceramic On-Demand Extrusion, Devin Mcmillen, Wenbin Li, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This work describes a process by which zirconium diboride (ZrB2) parts may be fabricated using the Ceramic On-Demand Extrusion (CODE) process. An oxide-carbide-nitride system consisting of ceramic powders and pre-ceramic organics, designed to yield ZrB₂ after reaction sintering, has been developed to produce an aqueous-based extrudate for subsequent processing in the CODE system. Pressurelessly sintered test specimens containing 1 wt% PVA binder achieve high relative density ≥ 99%. The viscoelastic response of the extrudate was characterized via spindle rheometry with a small sample adapter. Batches with 1 wt% PVA and 0.5 wt% Methocel show strong shear thinning characteristic, under …

Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content (< 1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Powders For Additive Manufacturing Processes: Characterization Techniques And Effects On Part Properties, Austin T. Sutton, Caitlin S. Kriewall, Ming-Chuan Leu, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Powder-bed based Additive Manufacturing is a class of Additive Manufacturing (AM) processes that bond successive layers of powder by laser melting to facilitate the creation of parts with complex geometries. As AM technology transitions from the fabrication of prototypes to end-use parts, the understanding of the powder properties needed to reliably produce parts of acceptable quality becomes critical. Consequently, this has led to the use of powder characterization techniques such as scanning electron microscopy (SEM), laser light diffraction, x-ray photoelectron spectroscopy (XPS), and differential thermal analysis (DTA) to both qualitatively and quantitatively study the effect of powder characteristics on part …

Investigation Of Tensile Properties Of Bulk And Slm Fabricated 304l Stainless Steel Using Various Gage Length Specimens, Sreekar Karnati, I. Axelsen, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The complex solidification dynamics and thermal cycling during Selective Laser Melting process is expected to result in non-equilibrium material characteristics. There is an essential need for characterization techniques which are critical towards the estimation of anisotropies. The current investigation is targeted towards establishing tensile testing methodologies and their relation to differing gage lengths. Dog-bone shaped specimen designs with gage lengths of 1”, 0.3” and 0.12” were employed in this research. The characterization was performed on hot rolled-annealed 304 stainless and SLM fabricated 304L stainless. It was theorized that smaller gage length specimens would be instrumental in mapping material property anisotropy …

Effect Of Powder Particle Size On The Fabrication Of Ti-6al-4v Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen, Lei Yan, Wei Li, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Direct Laser Metal Deposition (LMD) was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. Scanning electron microscopy (SEM), optical microscopy (OM) and energy dispersive spectroscopy (EDS) were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. X-ray diffraction (XRD) was used for the phase identification. After significant analysis, some differences were observed among …

Modeling And Experimental Investigation Of Pre-Mixed Multi-Powder Flow In Fabricating Functional Gradient Material By Laser Metal Deposition Process, Wei Li, Jingwei Zhang, Sreekar Karnati, Yunlu Zhang, Frank W. Liou, Joseph William Newkirk, Karen M. Brown Taminger, W. L. Seufzer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser Metal Deposition (LMD) is an effective process to fabricate Functionally Graded Material (FGM) from pre-mixed powders. Since the supplied multi-powder directly affects the deposited FGM’s composition, investigation on Pre-Mixed Multi-Powder (PMMP) flow during LMD is greatly needed. This paper presents a comprehensive numerical PMMP flow model. By solving discrete particle force balance equations coupled with continuity equations and momentum equations for carrier gas, the dynamic behavior of PMMP flow through powder feeder tube and out of nozzle was calculated. With this model, the particle sizes of multi-powder were optimized to obtain considered FGM composition. To verify the modeling results, …

Proposed Hybrid Processes For Part Building Using Fusion Welding And Friction Stir Processing, Megan A. Gegesky, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

It has been shown that a hybrid laser additive manufacturing and friction stir processing can deposit components with forged-like structures. This paper reports a hybrid fusion welding and friction stir process to create parts with quality structures. Combining traditional fusion welding and friction stir processing techniques for non-weldable aluminum alloys could facilitate the joining of difficult geometries in manufactured parts. This research illustrates mechanical property changes for non-weldable and weldable aluminum alloys. The Vickers hardness, and microhardness in the case of AA5052-H32, tensile strength and corrosion resistance of four processing states: base material, fusion welded material, friction stir welded material, …

Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning

Industrial and Manufacturing Engineering

The 3D printing industry has seen rapid growth in the last 10 years and has been called the next industrial revolution. There are several different processes used in 3D printing, but the most popular process is called Fused Filament Fabrication (FFF) or Fused Deposition Modeling (FDM). This is the process where (most commonly) plastic filament enters a nozzle, is heated to a semi-liquid state, and then deposited into a pattern to create a print. One major drawback to this process is that the prints are anisotropic. This means that the strength of the print varies with the orientation that it …

Biomimetic Seal Flipper Test Rig, Gordon D. Belyea, Laura Kawashiri, Dylan Rinker, Kurt Beske

Mechanical Engineering

No abstract provided.

Design And Testing Of A Top Mask Projection Ceramic Stereolithography System For Ceramic Part Manufacturing, Dylan Robert De Caussin

Master's Theses

Ceramic manufacturing is an expensive process with long lead times between

the initial design and final manufactured part. This limits the use of ceramic as a viable material unless there is a large project budget or high production volume associated with the part. Ceramic stereolithography is an alternative to producing low cost parts through the mixing of a photo curable resin and ceramic particles. This is an additive manufacturing process in which each layer is built upon the previous to produce a green body that can be sintered for a fully dense ceramic part.

This thesis introduces a new approach …

Metals Additive Manufacturing Powder Aging Characterization, Thomas Russell Lovejoy, Nicholas Karl Muetterties, David Takeo Otsu

Mechanical Engineering

The metallic additive manufacturing process known as selective laser melting requires highly spherical, normally distributed powder with diameters in the range of 10 to 50 microns. Previous observations have shown a degradation in powder quality over time, resulting in unwanted characteristics in the final printed parts. 21-6-9 stainless steel powder was used to fabricate test parts, with leftover powder recycled back into the machine. Powder samples and test specimens were characterized to observe changes across build cycles. Few changes were observed in the physical and mechanical properties of the specimens, however, there were indications of chemical changes across cycles. Potential …

Optimization Of Process Parameters In Micro Electrical Discharge Machining (Edm) Of Ti-6al-4v Alloy, Farshid Alavi

Masters Theses & Specialist Projects

Ti-6Al-4V has a wide range of applications such as in the automotive and aerospace industries. Nevertheless, titanium alloys are very difficult to machine by conventional methods. Micro-EDM is a non-conventional machining method that uses the thermal effect of precisely controlled sparks. Manufacturers are looking for the methods and optimal settings to increase the productivity of micro-EDM in terms of lessening machining time and tool wear. Moreover, surface integrity of the machined area is crucial for some products such as biomedical implants.

The objective of this study was to investigate the effects of the micro-EDM process parameters on response variables, in …

Paper Core Feeder System, Sergio Flores Velez

All Undergraduate Projects

Paragon Films has always strived to increase productivity and decrease waist within their company. The plant located in Union Gap, Washington currently has two production lines operating 24/7 managed by 2 to 3 people. The heavy line produces 5000 to 10000 revolutions per roll. This production line has a three part system that automatically feeds the paper cores to the spool shafts to roll the films. Therefore, the employees during that shift do not have to worry about filling up the bin very often. On the other hand, the second production line, which produces the hand films, does not have …

Conversion Casting: Adapter Hub, Joseph M. Coup

All Undergraduate Projects

The concept of conversion casting makes manufacturing major components much more efficient with regards to time and cost. The conversion cast of the adapter hub used in the Victair Mistifier is a major component that requires 8 hours to machine. The existing hub starts from steel stock and then that block of steel is placed into a CNC machine and coded in to create the adapter hub. The manufacturing method changes to a casting for the adapter hub will create a replicated part that requires 1.5 hours of post machining. The intricate design makes a conversion to casting more effective …

Multi-Use Fireline Handtool, Bruce W. Bernard Jr

All Undergraduate Projects

A wildland firefighter is a valuable resource to protecting public lands and managing fuels. The many hand tools used by firefighters aid in their ability to complete any required tasks effectively. Several of the tools available are specially purposed for individually grubbing, scraping, or liming. A small squad of firefighters could become a more effective resource if the tools they carried could perform several of these purposes as one single tool. To improve the effectiveness of an individual on the fireline a multi-use hand tool was designed to include an axe for liming and a heavy duty scraper for grubbing …

Properties Of Partially Stabilized Zirconia Components Fabricated By The Ceramic On-Demand Extrusion Process, Wenbin Li, Amir Ghazanfari, Devin Mcmillen, Ming Leu, Gregory Hilmas, Jeremy Watts

Faculty Publications, Mechanical Engineering

The Ceramic On-Demand Extrusion (CODE) process is a novel additive manufacturing process for fabricating dense ceramic components from aqueous pastes of high solids loading. In this study, 3 mol% Y2O3 stabilized tetragonal zirconia polycrystal (3Y-TZP) parts were fabricated using the CODE process. The parts were then dried in a humidity controlled environmental chamber and sintered under atmospheric pressure. Mechanical properties of the sintered parts were examined using ASTM standard test techniques, including density, Young’s modulus, flexural strength, Weibull modulus, fracture toughness and Vickers hardness. The microstructure was analyzed, and grain size was measured using scanning electron microscopy. The results compared …

A Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming Leu, Gregory Hilmas

Faculty Publications, Mechanical Engineering

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content (<1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.