Heat Transfer, Combustion Commons^™

Creation Of A Cip Method For The Heat Exchangers At Rolls-Royce, Melanie Howe, Austin Williams, Caroline Dempsey, Bethany Fralick

Journal of the South Carolina Academy of Science

Rolls-Royce produces various engines which must be tested prior to their distribution to ensure a high-quality product. The manufacturing plant contains four test cells where the engines can be subjected to high levels of torque and extreme temperatures. A heat exchanger is necessary in this testing system and over time, unwanted waste accumulates on the system’s plates. The team is tasked with developing and implementing a system mounted on a mobile cart which can provide data to determine whether the plates need to be cleaned. For this cleaning system to work, it must fully saturate the heat exchanger in cleaning …

Geometrically Complex Planar Heat Exchangers, Derli Dias Do Amaral Junior, Jose Lage

Mechanical Engineering Research Theses and Dissertations

In this study, geometrically complex planar heat exchangers, designed in line with the Constructal Law and operating at steady-state, are investigated numerically. The work is divided into two parts, one focusing on diffusion heat transfer in a rectangular plane and another on conjugate diffusion-convection heat transfer in a circular plane heat exchanger.

In the first part, a heat generating rectangular solid volume made of a low conductivity material is cooled through a small, isothermal side-section of the domain. The diffusion cooling process is improved by distributing within the heat generating material a fixed amount of a high conductivity material. The …

Tensile Testing Environmental Chamber – Structural, Michael Ingel, Erik Soldenwagner, Austin Marshall, Lauren Schirle

Mechanical Engineering

Environmental chambers for tensile testing machines are used to study how a multitude of materials behave in extreme temperatures. These chambers provide the necessary information to innovate cutting edge technology for materials in fields such as aerospace. These chambers are often heavy and expensive requiring a significant amount of time and money just in the installation process alone. This report will serve to outline and define the design and fabrication of an environmental chamber, conducted by a team of four senior mechanical engineering students at California Polytechnic State University, San Luis Obispo. The goals of the project include a low-weight …

Algorithm Development Of Topology Optimization For Pcm Based Heat Sinks, Diego L. De Los Reyes

Mechanical Engineering Undergraduate Honors Theses

With the inherent usage of the computer when dealing with additive manufacturing, it only makes sense to use that higher computing power through simulation and iterative design to use the mathematical concept of topology and optimize the kind of geometry and shapes to be produced for a certain application, especially thermal ones since most 3D printing applications focus on purely the mechanical. To determine what the shape will be, an objective function of how much heat can be dispersed from a hypothetical heat source, assumed to be a type of electronic device, is maximized while being constrained by other variables, …

Entertainment 721, Mark Hendricks, Noah John, Jadon Vanyo, Chelsea Payne

Williams Honors College, Honors Research Projects

The goal of this project was to design a luxury, aesthetically pleasing entertainment system with a TV lift mechanism that could be remote controlled. The design would also include a cooling cabinet for gaming systems, a remote locking system, and additional storage. Using a morphological chart and weighted decision matrix for each subsystem key features were determined to be included in the design. Several performance benchmarks were determined to accomplish the team’s design. Almost every benchmark was successful in the build of the first prototype. Several heat calculations and FEA analyses were performed on the system to ensure the success …

Thermo-Fluid Characterizations Of The Powder-Bed Fusion Additive Manufacturing Processes Using Laser And Electron Beam, M Shafiqur Rahman

LSU New Orleans Theses and Dissertations

The powder-bed fusion (PBF) process is a subdivision of Additive Manufacturing (AM) technology where a heat source at a controlled speed selectively fuses regions of a powder-bed material to form three-dimensional (3-D) parts. Two of the most effective PBF processes are selective laser melting (SLM) and electron beam additive manufacturing (EBAM), which can fabricate full-density metallic parts in a layer-by-layer fashion. In this study, thermal behavior and melt-pool dynamics in the PBF process are investigated by developing 3-D multiphysics-based thermo-fluid models for both SLM and EBAM, containing Ti-6Al-4V alloy as a powder-bed material. The laser and electron beams are modeled …

Fly Ash Based Geopolymer For High Temperature And High Compressive Strength Applications In Aggressive Environment, Aaryan Manoj Nair, Akm S. Rahman

Publications and Research

Geopolymers are the results of geosynthetic reactions between aluminosilicates and strong bases. This results in chemical bonds between aluminum (Al), Silicon (Si)and oxygen (O) composing polymer rings in tetrahedral coordination. These bonds give them widespread useful applications such as high heat bearing ceramics, and base construction material whilst being far more environmentally conscious. The purpose of the experiment is to examine the effect of Silicon Carbide whisker and inorganic glass particles on thermal and mechanical properties of Geopolymers. This study will help understand the effect of various compositions and concentrations of SiO₂ in mechanical strength. In this experiment, the …

Thermal Modeling Of Additive Manufacturing Using Graph Theory: Validation With Directed Energy Deposition, Jordan Severson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Metal additive manufacturing (AM/3D printing) offers unparalleled advantages over conventional manufacturing, including greater design freedom and a lower lead time. However, the use of AM parts in safety-critical industries, such as aerospace and biomedical, is limited by the tendency of the process to create flaws that can lead to sudden failure during use. The root cause of flaw formation in metal AM parts, such as porosity and deformation, is linked to the temperature inside the part during the process, called the thermal history. The thermal history is a function of the process parameters and part design.

Consequently, the first step …

Forge Burner, Caleb Desjardins

All Undergraduate Projects

Can small scale blacksmithing operations achieve a level of efficiency in their forge comparable to that of a large scale industry? The causes for the lack of efficiency needed to be pinpointed, and then the geometry of the existing design for the burner could be changed to fix the underlying issues, while still maintaining functionality. The problems with the previous design is the geometry of the intake giving an unknown air/fuel ratio, and the attachment of to the forge allowing the intake air to be contaminated by exhaust gasses. A burner needed to be designed that would solve these problems …

Development Of A Process For Thermal And Mechanical Modelling Of Screw-Driven Pellets Extrusion, Kaixiang Shi

Master’s Theses

The overall goal of the thesis project is to develop a process for thermal and mechanical modelling of the screw-driven pellets extrusion process, and applying the model results to design extruder temperature and flow rate controllers.

The proposed extruder is designed for metal 3D printing. The device demonstrates great potential in tackling some of the major issues faced by the metal additive manufacturing community. It eliminates the use of metal powder for workplace and workers safety. It is able to produce end-use parts with industrial grade mechanical and microstructural properties. It utilizes low cost metal-loaded polymer pellets as feedstock. However, …

Jominy Hardenability Tester With In-Situ Heating, Luke Allen

Williams Honors College, Honors Research Projects

This project centers on building a Jominy Hardenability tester with In-Situ heating for the manufacturing lab at the University of Akron. A new process and setup will be designed using engineering concepts in order to make the testing more efficient and safer for the teaching and testing of metal hardness. The current Jominy testing setup has efficiency issues within the transfer of specimen from induction heater to testing rig. Our design will simplify the design by creating a test rig that removes the traveling aspect of the specimen which will limit the amount of premature cooling done and will be …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Enhanced Heat Transfer Performance By Shape Optimization Of A Non-Axisymmetric Droplet Evaporating On A Heated Micropillar, Haotian Wu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Abstract

Enhanced Heat Transfer Performance by Shape Optimization of a Non-axisymmetric Droplet Evaporating on a Heated Micropillar

By

Haotian Wu

Department of Mechanical Engineering and Materials Science

Washington University in St. Louis, 2019

Research Advisor: Professor Damena Agonafer

The stacked multilayer 3D IC structure used in next generation high-powered electronics poses great challenges in dissipating their large heat flux, which causes extreme difficulties for traditional cooling technologies. In response, more advanced two-phase liquid cooling technologies, such as droplet evaporation, which utilizes the latent heat of vaporization to remove excessive heat, have been widely investigated. Compared to traditional single-phase cooling techniques, …

Critical Radius Of Insulation, Maria N. Ambrose, Samuel J. Sayre, Travis W. Martin, Matt T. Sterling

Mechanical Engineering

The critical radius of insulation is a counterintuitive concept within the study of heat transfer. The theory states that adding insulation to a cylindrical or spherical object will increase the rate of heat loss rather than decrease it, if the radius (thickness) of the insulation is at its “critical” value. The Critical Radius of Insulation Senior Project is designed to demonstrate this phenomenon to Heat Transfer students via a portable apparatus. The concept will be demonstrated with a cylindrical object which is heated by way of a separate voltage source. Thermocouples will display the temperature of the cylinder while insulation …

Repurposing Plastic Waste In El Cercado, Joseph Dooling, Kirby Townsend, Brendan Smith

Honors Thesis

This project aims to assist the community of El Cercado in the Dominican Republic in turning their plastic waste into useful products. The design team developed a first iteration shredder, injector, and aluminum mold which future design teams could further iterate in order to make products out of waste plastic. Different products were researched to ensure that they can be sold or used in the community. The goal of producing these items is to stimulate economic activity in the community by creating economic opportunity. The design shall also be sustainable in three ways. It shall reuse plastic waste while also …

Vaccine Cooler For The Global Poor, Benjamin J. Larson, Cooper E. Gibson, Eilbron Younan, Cody R. Volk

Mechanical Engineering

Cal Poly physics professors Peter Schwartz and Nathan Heston approached the Solar Freeze team with the problem that remote communities in Africa have limited access to modern-day medicine or vaccines. They suggested that we try and design a cooling device that can keep vaccines cold for multiple days at a time while the medicine is transported to remote villages. Currently, there are vaccine cooler products on the market, but most of them are very expensive or lack portability. Peter and Nate have tasked the Solar Freeze team to come up with a less expensive solution that is also portable and …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Carbon Fiber Recycler : Fiber Reclaimer, Alexander Edwards

All Undergraduate Projects

Boeing uses composite components for the 777x aircraft. The production of composite parts results in flashing (excess material) that must be trimmed and "thrown away" as scrap. Boeing is investigating means of recycling these scraps. The method proposed for this project is to delaminate and shred the composite material. The delamination process uses a ram to press two claw shaped devices together that bends and deforms the material in opposite directions. The chipper process uses counter rotating saw blades spaced 1/8” apart to produce small shredded material. This shredding material is pyrolyzed (heated) to decay the resin leaving the carbon …

The Effects Of 3d Printing Parameters And Surface Treatments On Convective Heat Transfer Performance, Lucas N. Pereira

Electronic Theses and Dissertations

Additive manufacturing technology and applications have quickly expanded in many industries over the last five years. As additive manufacturing is studied and refined, improvements in resolution and strength have helped propel further growth of the industry. This study focuses on an additive manufacturing technology called fused filament fabrication (FFF). FFF involves the extrusion and layer-by-layer deposition of a molten thermoplastic material to create the desired part. One potential new application of fused filament fabrication is the manufacture of heat exchangers and heat sinks. This study focuses on developing baseline experimental data related to convective heat transfer coefficients over surfaces of …

Influence Of Micro-Nucleate Boiling On Annular Flow Regime Heat Transfer Coefficient Values And Flow Parameters – For High Heat-Flux Flow Boiling Of Water, Soroush Sepahyar

Dissertations, Master's Theses and Master's Reports

Analysis of results from steady and steady-in-the-mean high heat-flux (15 - 70 W/cm², with water as working fluid) shear driven annular flow-boiling experiments presented here - and low heat-flux (0.1- 1 W/cm², with FC-72 as working fluid) experiments presented elsewhere – together lead to a key conclusion. The conclusion is that heat carrying nucleation rates go often undetected by the typically used visualization approaches for flow boiling – as such flows often involve µm- to sub- µm scale bubble diameters in millimeter-scale ducts. These nucleation rates play a significant role in most of the so-called convective …

Multi-Scale, Capillary Assisted Copper Surfaces For Enhanced Pool Boiling Heat Transfer Processes, Chetan Agarwal

Dissertations, Master's Theses and Master's Reports

Phase-change heat transfer through pool boiling process offers a promising thermal management solution in applications wherein conventional air or single-phase liquid-based cooling methods prove inefficient such as for high-power electronics. Pool boiling process, which utilizes the latent heat of evaporation, provides a robust and efficient way to efficiently dissipate the excessive heat generated in a small footprint area in particular as seen in CPUs (Central Processing Units), GPUs (Graphics Processing Units), LEDs (Light Emitting Diodes), radars, and other demanding computing, sensing and surveillance electronics. Although boiling process has been studied for over five decades, it has not been yet adapted …

Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston

Mechanical Engineering Undergraduate Honors Theses

Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …

Process-Property-Microstructure Relationships In Laser-Powder Bed Fusion Of 420 Stainless Steel., Subrata Deb Nath

Electronic Theses and Dissertations

Laser-powder bed fusion (L-PBF) is an additive manufacturing technique for fabricating metal components with complex design and customized features. However, only a limited number of materials have been widely studied using L-PBF. AISI 420 stainless steel, an alloy with a useful combination of high strength, hardness, and corrosion resistance, is an example of one such material where few L-PBF investigations have emerged to date. In this dissertation, L-PBF experiments were conducted using 420 stainless steel powders to understand the effects of chemical composition, particle size distribution and processing parameters on ensuing physical, mechanical and corrosion properties and microstructure in comparison …

Modeling Residual Stress Development In Hybrid Processing By Additive Manufacturing And Laser Shock Peening, Guru Charan Reddy Madireddy

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The term “hybrid” has been widely applied to many areas of manufacturing. Naturally, that term has found a home in additive manufacturing as well. Hybrid additive manufacturing or hybrid-AM has been used to describe multi-material printing, combined machines (e.g., deposition printing and milling machine center), and combined processes (e.g., printing and interlayer laser re-melting). The capabilities afforded by hybrid-AM are rewriting the design rules for materials and adding a new dimension in the design for additive manufacturing paradigm. This work focuses on hybrid-AM processes, which are defined as the use of additive manufacturing (AM) with one …

The Kentucky Re-Entry Universal Payload System (Krups): Sub-Orbital Flights, James Devin Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable testbed for atmosphere entry science experiments, with an initial application to thermal protection systems (TPS). Because of the uniqueness of atmospheric entry conditions that ground testing is unable to replicate, scientists principally rely on numerical models for predicting entry conditions. The KRUPS spacecraft, developed at the University of Kentucky, provides an inexpensive means of obtaining validation data to verify and improve these models.

To increase the technology readiness level (TRL) of the spacecraft, two sub-orbital missions were developed. The first mission, KUDOS, launched August 13th, 2017 on a Terrier-Improved Malamute …

Capillary-Assisted Enhanced Condensation Heat Transfer For Low Surface Tension Liquids, Gnana Vishnu Durgam

Dissertations, Master's Theses and Master's Reports

Extensive research has been carried out over the course of the last few decades to induce dropwise condensation as it offers 5 - 7 times better heat transfer performance compared to filmwise condensation process. A number of methods such as low surface energy hydrophobic coatings, surface modification of hydrophobic surfaces to fabricate micro, nano and hierarchical structures, and the recent incorporation of jumping droplet phenomenon have provided effective means to further enhance the condensation heat transfer. However, existing methods to enhance condensation heat transfer rate fail in the case of low surface tension, highly wetting liquids such as hydrocarbons, cryogens, …

Additive Manufacturing For Post-Processing, Nathan D. Goodwin, Andrew Furmidge

Mechanical Engineering

Additive Manufacturing for Post Processing (AMPP) is a team comprised of two Cal Poly Mechanical Engineering students: Nathan Goodwin and Andrew Furmidge. The project is focused in the area of metal additive manufacturing (AM) machines, which are still a developing technology. Improvements have been made to the quality of the machines in the past years, but many limitations still exist. One of these is the inability to print parts that are larger than the build volume. In an effort to solve this problem, whole parts are divided into pieces that are printed individually. This team’s senior project is to create …

Beer Rack On Demand Water Heater, Jason Warenski

All Undergraduate Projects

On-Demand Water Heater (for homebrewing systems)

By Jason Warenski (Engineering Technologies)

The on-demand water heater is being built for a home brewing system. The is intended to improve brewing process efficiency while reducing the footprint of the brewing equipment. The device contains a coil made from 3/8” soft copper tubing. The coil is inserted into a housing which is constructed of two 22-gauge stainless steel cylinders and a layer of ceramic insulation. Attached to the inlet and outlet of the coil are monitoring and control devices. On the inlet is a water flow meter which allows the user to monitor …

Utilizing Reprap Style 3d Printers For The Manufacturing Of Composite Heat Exchangers, John Laureto

Dissertations, Master's Theses and Master's Reports

The low cost 3D printing market is currently dominated by the application of RepRap (self-replicating rapid-prototyper) variants. Presented in this document are practical utilizations of RepRap technology. Developed are innovative processes to manufacture composite materials systems for thermal management solutions.

First, a laser polymer welder system is validated by quantifying maximum peak load and weld width of linear low density polyethylene (LLDPE) lap welds as a function of linear energy density. The development of practical engineering data, in this application, is critical to producing mechanically durable welds. Developed laser and printer parameter sets allow for manufacturing of LLDPE multi-layered heat …

Final Design Report: Allergen Mixing Assistant (Ama) Micro-Refrigeration Redesigning, Mitchell Parks, Minwoo (Michael) Suh

Mechanical Engineering

Abstract

Allergen Mixing Assistant (AMA) by Xtract Solutions is a device designed to more “effectively refrigerate, organize, and mix allergenic extracts”. Although Xtract Solutions intended the product to be fully automated, the company has decided against its automation and declared its current design as a minimum viable product whose components are too expensive, difficult to source and complex. Therefore, Cal Poly AMA design team - Mitchell Parks and Minwoo Suh - has decided to replace these expensive components with much more economical alternatives as shown below:

Stirling cooler

→

Thermoelectric (Peltier) cooler

Custom Arduino

Controller Card

→

TEC Thermostat *** …