Energy Systems Commons^™

Feasibility Study On Concentrated Solar Power Plants In Malaysia, De Jen Choy

Student Works (2020-2029)

The rapidly growing economy and population in Southeast Asia has elevated the need for affordable, secured, sustainable and environmentally friendly energy sources. One such energy source is solar energy which is a suitable energy source for most Southeast Asian countries which are within the Sun Belt region. This study performs a performance and financial analysis on concentrated solar power (CSP) technologies, specifically the solar power tower (SPT) in the Malaysian environment through the use of simulation software. The significance of the study lies in the fact that limited research has been done on CSP technologies in Malaysia and the study …

Thermodynamic Analysis And Optimization Of Organic Rankine Cycles Using 1-Butylpyridinium Tetrafluoroborate As A Geothermal Fluid, Kazemi Shabnam

Student Works (2020-2029)

Organic Rankine cycle (ORC) is a promising technology for electricity generation by utilizing heat sources at low to moderate temperature that ranges between 80-350° C. In the present work, an ionic liquid (1-butylpyridinium tetrafluoroborate, C9H14NBF4), a known green chemical and non-volatile compound with good thermal and chemical stability, significant heat capacity, low vapor pressure and a wide liquid temperature range (25 to 459 °C), is utilized as a geothermal fluid. Simulation and optimization were conducted for a basic organic Rankine cycle (basic ORC), a regenerative organic Rankine cycle (RORC) and a two-stage evaporative organic Rankine cycle (TSORC) by maximizing exergy …

Study Of Heat Transfer And Friction Loss Of Nanofluid Suspension Flow In Circular Pipe Heat Exchanger, Ramadas Sandru

Student Works (2020-2029)

This stated experiment focused on the study of convective heat transfer and friction loss in a circular flow passage for Graphene oxide-based nanofluids which are consist of Graphene Oxide/Distilled water with their different wt. % concentrations. These GO/DW based nanofluids where been prepared by using a facile two-step method, while the GO particles were synthesized by a modified hummer method. Four different (0.025, 0.05, 0.075, and 0.1 wt. %) were produced by dispersing graphene particles in distilled water under high probe sonication. The GO/DW based nanofluids flowing in a horizontal shell and tube heat exchanger counter flow under turbulent flow …

Optimization Of Bioethanol Production, Engine Performance And Exhaust Emissions From Manihot Glaziovii And Sweet Sorghum In A Spark Ignition Engine, Sebayang Abdi Hanra

Student Works (2020-2029)

The ever-increasing fossil fuel consumption over the years is attributable to economic and population growth, which in turn, increases greenhouse gas emissions. Bioethanol is one of the promising solutions to address the depletion of fossil fuels as well as environmental problems. Manihot glaziovii tubers and sweet sorghum grains are inedible feedstocks that can be used for bioethanol production. The carbohydrate content (70%) of these biomasses makes them suitable as feedstocks for bioethanol production. In this study, enzymatic hydrolysis (liquefaction and saccharification) was used to obtain the reduction of sugars. The enzymes α-amylase from Bacillus licheniformis Type XII-A and amyloglucosidase from …

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

Modeling And Control Of Solar Pv With Battery Energy Storage For Rural Electrification, Irene Masenge

Tanzania Journal of Engineering and Technology (TJET)

In rural areas where electric power grid network is rarely available, power generation from renewable energy resource such as solar photovoltaic (PV) is mostly accomplished in standalone mode. The standalone solar PV system requires energy storage device to achieve reliable power supply to the end users. This paper presents modelling and coordination control of solar PV with battery energy storage system (BESS) for rural-electrification applications. The proposed control is accomplished via a bidirectional buck-boost converter with the objective of maintaining voltage at the DC bus constant. Simulation results based-on MATLAB/Simulink platform confirms good performance of the proposed system

Quantifying The Environmental Impacts Of Cookstove Transitions A Societal Exergy Analysis Based Model Of Energy Consumption And Forest Stocks In Honduras, Noah Ver Beek, Elvin Vindel, Matthew K. Heun, Paul E. Brockway

University Faculty Publications and Creative Works

Unsustainable consumption of biofuels contributes to deforestation and climate change, while household air pollution from burning solid biofuels in homes results in millions of premature deaths globally every year. Honduras, like many low and medium Human Development Index countries, depends on primary solid biofuels for more than 30% of its primary energy supply (as of 2013). We conducted a societal exergy analysis and developed a forest stock model for Honduras for 1971–2013 and used the results to model an energy transition from traditional wood stoves to either improved efficiency wood cookstoves or modern fuel cookstoves (using Electricity or Liquefied petroleum …

Development Of Water Coning Control Design Metrics In Naturally Fractured Reservoirs, Samir Prasun

LSU Doctoral Dissertations

Naturally fractured reservoirs (NFRs) with bottom-water are known for their instant water breakthrough and severe water coning that reduces oil recovery. This is because water channels through the highly permeable fractures easily connecting the well to the aquifer bypassing the oil contained in the matrix. Remedial techniques such as producing below critical-oil rate, optimizing the well spacing and installing the downhole water sink (DWS)/ downhole water loop (DWL) technology, have already been successfully tested in single-porosity reservoirs (SPR). However, applicability of these techniques in NFRs are unknown since only a few studies have been performed on their feasibility in NFRs, …

Fsec Energy Research Center Strategic Plan (2020-2025) Executive Summary, Florida Solar Energy Center, James Fenton

FSEC Energy Research Center®

The Florida Legislature created the Florida Solar Energy Center (FSEC) in 1975 to support the growth and development of renewable energy. The year 2025 will mark the half-century mark for FSEC's service as the statewide energy research and education institute. In preparation for the next 50 years of dynamic energy developments, the FSEC Energy Research Center is undertaking a strategic planning and rebranding process.

Cal Poly Microgrid Fixed Pv Array, Christopher L. Ewert, Justin R. Syracuse, Donald A. Syracuse, Jason M. Kehl

Mechanical Engineering

The Mechanical Engineering Department at California Polytechnic State University of San Luis Obispo would like an adjustable, fixed angle solar panel mount to help educate students on basic solar energy principles. Our team has developed a unique sawhorse design utilizing ideation techniques and design selection tools. The selected design allows for multiple panel adjustability and control of both azimuth and tilt angle. Safety concerns are addressed with action plans to mitigate risk. Concept prototypes to justify gearbox functionality and subsystem cohesion was utilized to reduce manufacturing issues. Manufacturing began in March 2020 and proceed through until the end of the …

Thermal Energy Storage For Load Shifting, Jordan Benton Lopez Corley, Weston Cruz Montgomery, Taylor Glenn Harms

Mechanical Engineering

The following document accounts for the progress made in the prototype development of our design solution since the Critical Design Review, and our group’s response to recent world events which greatly impacted planned activities. Our design challenge is to develop a thermal energy storage system which will sequester the energy from a photovoltaic (PV) array during the day and allow for its dispersal at night in the form of near boiling water. Looking at our user’s needs, we broke our design solution into four components: water heating, storage, distribution, and controls. Research of all components was conducted to ascertain which …

Performance Analysis For Single-Stage And Multi-Stage Coreless Axial Flux Permanent Magnet Generator With Different Rotor Structures, Habib Asiful

Student Works (2020-2029)

Axial flux permanent magnet (AFPM) generator is a good candidate for both low and high-speed applications. Compared to radial flux machines, AFPM generators can be easily cascaded for enhanced power/torque while maintaining a fixed machine diameter. To improve power density and reduce cogging torque, some researchers have proposed the removal of iron core in the stator of AFPM machine, giving rise to the concept of coreless AFPM machine. Nevertheless, most of these coreless machines still require back iron on the rotor and/stator to reduce leakage flux. In this project, different rotor structures for single-stage coreless AFPM generators were considered, using …

Design Of Structural Stand For High-Precision Optics Microscopy, Sara T. Novell

Master's Theses

Lawrence Livermore National Lab (LLNL) is home to the National Ignition Facility (NIF), the world’s largest and most energetic laser. Each of the 192 beamlines contains dozens of large optics, which require offline damage inspection using large, raster-scanning microscopes. The primary microscope used to measure and characterize the optical damage sites has a precision level of 1 µm. Mounted in a class 100 clean room with a raised tile floor, the microscope is supported by a steel stand that structurally connects the microscope to the concrete ground. Due to ambient vibrations experienced in the system, the microscope is only able …

Integrated Resource Plan For Portland General Electric (Pge), Mary Biswal, Alejandro Castelan

Master's Projects and Capstones

An integrated resource plan (IRP) for Portland General Electric (PGE) is developed in this master’s project. The IRP is based on capacity expansion modeling for zero-carbon emission scenarios. PGE is a public electric utility based in Oregon and serves around 887,000 customers across a territory of 4,000 sq. miles. The utility’s resource mix is currently heavily dependent on natural gas making up almost 50% of its capacity. While the state renewable portfolio standards (RPS) require Oregon power utilities to derive 50% of their generation from renewable sources by 2040, PGE plans to move rapidly into a clean energy mix by …

An Integrated Resource Plan For Arizona Public Service Electric (Aps), Irene Boghdadi, Randy Chiu

Master's Projects and Capstones

Our Masters Capstone Project is an Integrated Resource Plan (IRP) for Arizona’s largest electric utility, Arizona Public Service Electric (APS).

An IRP is developed by utilities to identify the optimal combination of demand- and supply-side resources needed to reliably meet forecasted demand for energy and capacity, including a planning reserve margin, over a future period.

In addition to APS’s obligation to serve the growing load in Arizona while minimizing costs, it is required by the state to adhere to the Renewable Energy Standard (RES) policy of 15 percent retail sales from renewable energy resources by 2025.

The analysis described in …

Large Scale Grid Integration Of Wind And Solar Power With Storage, Nicholas Moore

Macalester Journal of Physics and Astronomy

The current energy grid in the United States is dominated by carbon intense energy generation methods that are based on production when and where it is required. However, solar and wind power have proved themselves as the most promising carbon free energy generation sources. Due to the unpredictable and uncontrollable nature of energy production from solar and wind, large scale integration of these resources into the electric grid will require robust storage capacity. In this project, we model the energy grid of the Midcontinent Independent System Operator (MISO) energy region with high concentrations of solar and wind power to analyze …

New Policies Give Solar Users An Economic Boost, Olivia Fowler

Marriott Student Review

The future looks bright for Solar Energy, as more States and Territories in the United States commit to moving to 100% renewable energy. What are the different states and territories committing to exactly, and what economic incentives are they bringing? Find out in this article by author Olivia Fowley.

Portable Calorimeter For Fire Experiments, Kayla Collins, Kara Hewson, Christopher Chen, Joel Keddie

Mechanical Engineering

Executive Summary

An oxygen consumption calorimeter works by measuring the heat release rate of a burning substance. This value is calculated by measuring the oxygen and byproducts in smoke from afire.In order to get these values two types of sensors were used. A non-dispersive infrared sensor (NDIR) that measured CO and CO2 and a zirconium O2 sensor were used to find their respective gas concentrations.The design to calculate the heat release rate is focused on maximizing sensor accuracy and portability while simplifying the manufacturing by using off-the-shelf components. The goal included making the system simple to recreate and package in …

A History And Status Of Wind Energy Potential In Arkansas, Pre And Post Covid-19, Will Blasingame

Mechanical Engineering Undergraduate Honors Theses

Historically, wind-generated electricity has been the largest renewable energy sources in the United States. Wind-rich regions like Oklahoma and Texas have fueled growth and sold that electricity to electric utilities located in wind-poor states like Arkansas in the form of Power Purchase Agreements. Future technologies such as Vertical Axis Wind Turbines, small wind turbines, and Tesla turbines designed to generate electricity from wind show promise in unlocking more expensive wind resources in regions like Northwest Arkansas by mitigating concerns about low wind speeds and noise. However, more factors than just feasibility influence the growth of wind power. Governmental policies such …

Computational Analysis Of A New Planar Mixing Layer Flame Configuration To Study Soot Inception, Carmen Ciardiello

Honors Scholar Theses

The production of soot is omnipresent in society today. Soot is the product of many of the combustion processes that provide the bulk of the usable energy throughout the world. Furthermore, soot particulate poses a great danger to both the environment and all forms of life on Earth. It has proven to pollute ecosystems, foster health problems for human beings, and degrade air quality [1].

These dangers make studying and understanding soot particulate paramount for improving the quality of life. Thus, this study introduces a new flame configuration for studying soot inception. Presently, various common flame configurations have been found …

An Assessment Of Renewable Energy Technology Implementation In Storrs, Connecticut: Emissions Reduction And Feasibility Of A Microgrid System At Uconn, Sophie Macdonald

Honors Scholar Theses

The purpose of this project is to design a clean energy-sourced microgrid for UConn’s main campus that would reduce the university’s energy emissions while remaining within the geographic boundaries of viable UConn-owned land. Economic cost was not considered in this analysis; instead, emissions and space constraints were the optimized measures of value and feasibility. Sources of energy that were considered include photovoltaics (PV), wind turbines, hydrokinetic systems, and fuel cells. Energy storage capacity was included in the analysis as well. The overall system was optimized first by ignoring space constraints and for a minimum of 10% reduction from the current …

Efficiency Analysis Of Harvesting Solar Energy To Perform Mechanical Work, Haden S. Bragg

Undergraduate Theses and Capstone Projects

The majority of the world’s electricity is generated using fossil fuels; in fact, the United States Energy Information Administration (EIA) states that the U.S. used fossil fuels to generate 62.7 % of its electricity in 2019 [1]. The goal of this research was to create a system that could perform mechanical work using only renewable resources. We built a solar charging station that uses two solar panels to generate electricity and an electric bicycle whose battery can be charged using the charging station. The efficiency for the type of solar cell used in this project is well established. Therefore, in …

The Application Of Evolutionary Algorithms In Multi-Objective Design And Optimization Of Air Cooled Heatsinks, Younis Osama Abdelsalam, Sajad Alimohammadi, Tim Persoons

Articles

Genetic algorithms (GAs) are considered to be one of the main types of evolutionary algorithms (EAs) and are being increasingly used in various engineering design applications. To a large extent, plate-fin heatsinks are used in the thermal management of compact electronic equipment and data centers. The shape optimization of the heatsinks is not rigorously investigated during the design process of high power electronics. Any improvements in the effectiveness of the heatsinks impact the energy consumed by large-scale information communication technology (ICT) facilities including data centers and telecommunication systems and promote a more sustainable use of raw materials. This paper investigates …

Fluid Power Vehicle Challenge, Jacob Torrey, Kayla Londono, Bryson Chan, Aaron Trujillo

Mechanical Engineering

The FPVC combines mechanical engineering disciplines to design and manufacture a vehicle that utilizes hydraulic power. The FDR covers the final manufacturing process and verification processes developed during the front end of research and analysis built upon the Critical Design Review (CDR) and the PDR (Preliminary Design Review). This report showcases the design decisions and extensive research that supports the continuing efforts by the Team Pump My Ride, to build upon the accomplishments of Cal Poly’s previous team, The Incompressibles. The FDR presents how Team Pump My Ride produced the design changes from the CDR and PDR to achieve improvements …

Effect Of Chromium Trioxide Coating On The Thermal Performance Of Solar Thermal Collector, Èkram Hadi Alaskaree, Osamah Raad Skheel Alkhafaji, Nizar F. O. Al-Muhsen

Karbala International Journal of Modern Science

This paper compared the thermal performance of two solar collectors. The first collector is coated by a dark black absorbent solar collector, and the second one coated by the chromium trioxide. The results of the second collector show a better selectivity in terms of greater radiation absorption, and less emission compared to the first collector. At the minimum solar irradiance time, the absorbed energy is increased from 908.28J to 1221.5J, and the thermal efficiency is improved from 37.3% to 50.1% when the chromium trioxide coating is used. Besides, at the maximum solar irradiance time, the absorbed energy is increased from …

Dartmouth Formula Racing: Full Electric Battery System Design, Matt Gardner, Jacob Hagler, Ruthie Nordhoff, Otto Salmi

ENGS 89/90 Reports

Dartmouth Formula Racing (DFR) lacked an electrical energy storage system that was Formula Hybrid rules-compliant, optimized for FH events, safe, reliable, and integrated with the rest of their vehicle. Additionally, the team lacked the academic and professional resources required to bring a thorough, analytical approach to the design, testing, and documentation of the new storage system. Our team designed and built a Lithium-Ion battery pack (accumulator) containing energy storage, active cooling, battery management and temperature monitoring systems, and control circuitry compatible with DFR’s vehicle. Collaboration throughout design, fabrication, assembly and testing processes ensured effective knowledge transfer to the DFR team.

Side-By-Side Testing Of Solaire Solar Ac, Florida Solar Energy Center, John Sherwin

FSEC Energy Research Center®

The FSEC Energy Research Center performed a series of side-by-side tests to compare a heat pump system with a SolAire thermal collector against one without. The tests were performed in three phases: 1) baseline operation, 2) heat pump system operating with SolAire collector using collector manufacturer's wiring specifications, and 3) heat pump system operating with SolAire collector using Daiken/OEM wiring specifications. Each phase represented 5 full days of continuous operation during August of 2018 in Cocoa, Florida. Phase 1 baseline testing demonstrated that the two Daiken heat pump systems and test houses performed similarly and there were no differences between …

Reverse Osmosis; Addressing Freshwater Shortage With Sustainable Desalination, Jessica Savage

Sustainability Conference

Water security is an imperative part of high-functioning societies. Currently, large populations of the globe live in water-impoverished or water-stressed areas. With climate change and growing global populations, projections show more people being impacted by issues of water shortage.

One solution to water security is the implementation of desalination, specifically with reverse osmosis systems. This presentation walks through the history, capabilities, future work, and explanations on how reverse osmosis systems work. With continued research on improving desalination, communities in both developed and developing nations around the world can work towards total water security.