Energy Systems Commons^™

Test 2224: John Deere 8r 410, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2228: John Deere 8rx 410, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1194: John Deere 6145m Ft4, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Electrification Of Domestic Hot Water To Aid The Integration Of Renewable Energy In The California Grid, Alejandro Cervantes

Cal Poly Humboldt theses and projects

Water heating in residential buildings, also known as domestic hot water (DHW), is the third largest use of energy after appliances and space conditioning. About 90% of the residential buildings in the state use natural gas fueled water heaters, 6% use electricity, and a small percent use liquefied petroleum gas (LPG) or solar water heaters. The current energy use associated with residential water heating is small relative to the total amount of energy consumption in the residential building sector, but it is still a contributor of greenhouse gas (GHG) emissions. Improving hot water systems can be beneficial for bill customer …

Indirect Thermosiphon Flat-Plate Solar Collector Performance Based On Twisted Tube Design Heat Exchanger Filled With Nanofluid, Mahmoud Eltaweel, Hazem Hussien, Ahmed A. Abdel-Rehim

Mechanical Engineering

No abstract provided.

Energetic And Exergetic Analysis Of A Heat Pipe Evacuated Tube Solar Collector Using Mwcnt/Water Nanofluid, Mahmoud Eltaweel, Ahmed A. Abdel-Rehim

Mechanical Engineering

Increasing the energy demand and the limited availability of conventional energy sources are the main challenges to secure the human future. Solar energy is an attractive source of energy to ensure the sustainability of energy in this world for now and for the future. Evacuated tube solar collector is a solar thermal collector mostly used for domestic applications. The replacement of the working fluid with nanofluid can enhance the heat transfer even for low temperature applications. The effect of multi-walled carbon nanotubes and water nanofluid as working fluid in evacuated tube solar collector is used to experimentally investigate the energy …

Techno-Economic Feasibility Of Solar Powered Electric Vehicle Charging Stations In West Virginia, Houssem Eddine Younes

Graduate Theses, Dissertations, and Problem Reports (ETD)

This project explores the techno-economic feasibility of installing a photovoltaic (PV) system to power electric vehicle (EV) charging stations in West Virginia. A case study of a parking garage charging station is considered. The PV system performance and economic feasibility are assessed for two different system configurations and two financial scenarios. Two system variations one including PV only and another with on-site storage battery are modelled using the System Advisor Model (SAM) developed by the National Renewable Energy Laboratory. Initial technical specifications of the PV system, battery system and EV chargers were selected as a reference case. Through parametric simulation, …

Real-Time Predictive Control Of Connected Vehicle Powertrains For Improved Energy Efficiency, Joseph Oncken

Dissertations, Master's Theses and Master's Reports

The continued push for the reduction of energy consumption across the automotive vehicle fleet has led to widespread adoption of hybrid and plug-in hybrid electric vehicles (PHEV) by auto manufacturers. In addition, connected and automated vehicle (CAV) technologies have seen rapid development in recent years and bring with them the potential to significantly impact vehicle energy consumption. This dissertation studies predictive control methods for PHEV powertrains that are enabled by CAV technologies with the goal of reducing vehicle energy consumption.

First, a real-time predictive powertrain controller for PHEV energy management is developed. This controller utilizes predictions of future vehicle velocity …

Utility-Scale Solar Pv Performance Enhancements Through System-Level Modifications, Andrew D. S. Glick, Naseem Ali, Juliaan Bossuyt, Marc Calaf, Raul Bayoan Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Performance of solar PV diminishes with the increase in temperature of the solar modules. Therefore, to further facilitate the reduction in cost of photovoltaic energy, new approaches to limit module temperature increase in natural ambient conditions should be explored. Thus far only approaches based at the individual panel level have been investigated, while the more complex, systems approach remains unexplored. Here, we perform the first wind tunnel scaled solar farm experiments to investigate the potential for temperature reduction through system-level flow enhancement. The percentage of solar irradiance converted into electric power depends upon module efficiency, typically less than 20%. The …

Piezoelectric Energy Harvester Improvement, Nathan Embaugh, Jason Mack, Jeremiah Fitzgerald, Zachary J. Lindsey

Williams Honors College, Honors Research Projects

The energy harvester is used to convert a portion of the tire deflection waste energy to power up tire embedded sensors. A piezoelectric energy harvester is designed and some preliminary tests are done on it. So far, it has been shown that this design is sufficient for tire application. The team will need to modify the design of the energy harvester, the measurement setup and add a temperature and a strain senor to the existing setup so that the tire deflection and temperature can be measured and at the same time the energy harvester should be tested to see how …

Internet Of Things In Sustainable Energy Systems, Abdul Salam

Faculty Publications

Our planet has abundant renewable and conventional energy resources but technological capability and capacity gaps coupled with water-energy needs limit the benefits of these resources to citizens. Through IoT technology solutions and state-of-the-art IoT sensing and communications approaches, the sustainable energy-related research and innovation can bring a revolution in this area. Moreover, by the leveraging current infrastructure, including renewable energy technologies, microgrids, and power-to-gas (P2G) hydrogen systems, the Internet of Things in sustainable energy systems can address challenges in energy security to the community, with a minimal trade-off to environment and culture. In this chapter, the IoT in sustainable energy …

Designing A Recycling Facility For Energy Materials, Bartholomew Kitko, Matthew Berger, Elias Chiti, Trayce Harris, Mark Kulesa

Williams Honors College, Honors Research Projects

The purpose of this design project is to create a recycling facility for energy materials. Different energy systems will be analyzed to determine the most economically appropriate energy material to recycle. A list of the energy systems to be analyzed includes catalyst converters, wind turbines, lithium ion batteries, photo-voltaic cells, and precious materials with high energy applications. This study involves two main parts: the research to determine the most appropriate energy material for recycling, while also choosing or creating recycling processes efficient enough to reduce the US’s reliance on foreign nations for obtaining their rare-earth materials. The second part is …

Measurement Of Current Distribution In The Land Channel Direction Of A Proton Exchange Membrane Fuel Cell, Chinmay Kulkarni

Dissertations, Master's Theses and Master's Reports

A fully functional proton exchange membrane fuel cell with single land channel geometry on the cathode and segmented anode current collector with 9 mm² active area with a 350μm spatial resolution was utilized to measure the local current distribution in the land channel direction. A distinguished printed circuit board approach was used for the data acquisition to adapt to any flow field design.

Performance of this segmented cell was examined at dry, wet and moderate humidity settings to study the water transport phenomenon in the PEMFC. In the dry condition at 60 ͦ C with 0% relative humidity, the …

High-Performance Zero Liquid Discharge (Zld) Treatment Of High-Salinity Brines Using A Multiple-Effect Absorption Distillation Concept, Sunil Pinnu

Dissertations, Master's Theses and Master's Reports

State-of-the-art zero liquid discharge (ZLD) technologies are currently bound with either intensive use of high-grade electrical energy such as mechanical vacuum vapor compressors utilized in brine crystallizers or high capital cost with environmental concerns such as evaporation ponds. The present study aims to address these issues by an innovative desiccant-based ZLD system in which a multiple-effect distillation (MED) unit is uniquely embedded at the heart of an absorption-desorption system. Here, the MED and absorption systems are inherently coupled enabling both heat and mass transfer processes between a high-salinity water and a desiccant solution. The proposed technology employs an absorption-based thermally-driven …

A Reduced Model For Microbial Electrolysis Cells, Dina Aboelela, Moustafa A. Soliman, Ibrahim Ashour

Chemical Engineering

Microbial electrolysis cells (MECs) are breakthrough technology of cheap hydrogen production with high efficiency. In this paper differential-algebraic equation (DAE) model of a MEC with an algebraic constraint on current was studied, simulated and validated by implementing the model on continuous-flow MECs. Then sensitivity analysis for the system was effectuated. Parameters which have the predominating influence on the current density and hydrogen production rate were defined. This sensitivity analysis was utilized in modeling and validation of the batch-cycle of MEC. After that parameters which have less influence on MEC were eliminated and simplified reduced model was obtained and validated. Finally, …

Adapting To Extreme Heat: Social, Atmospheric, And Infrastructure Impacts Of Air Conditioning In Megacities - The Case Of New York City, Harold Gamarro

Dissertations and Theses

Extreme heat events are becoming more frequent and intense in most large cities. Built-up surfaces also limit cooling mechanisms, leading to warmer conditions in cities, a phenomenon called the Urban Heat Island (UHI). This presents major challenges to reduce adverse health effects of hot weather, particularly in vulnerable populations like the elderly and low-income communities. Here we explore the overall impacts of increasing air conditioning (AC) system adoption in residences as an adaptive measure to reduce human health risks under heat waves, with New York City (NYC) as a case study. This study uses AC adoption data from the 2017 …

Capillary Forces And Wetting Dynamics By Diffuse-Interface Modeling, Fanny Thomas

Dissertations and Theses

Wetting phenomena underlie many natural and industrial processes, from the proper functioning of the lungs to the thin coating of surfaces. The three-phase interactions involved at microscopic scales play a critical role. Adding solid particles to an emulsion, for example, can drastically change the flow behavior due to capillary bridging between the particles. The study of these three-phase systems is especially relevant to the petroleum industry, where gas hydrates forming large clusters in subsea pipelines during crude oil transportation is a major concern. The dynamics of such systems is also of great interest from a fundamental perspective. Indeed describing non-equilibrium …

On The Energy Sustainability Of Active And Passive Building Integrated Technologies In The Context Of A Changing Climate For Tropical Coastal Cities, Rabindra Pokhrel

Dissertations and Theses

Caribbean Sea surface temperatures have been rising at an alarming rate of 0.020C/year. The effect of rising sea surface temperatures is reflected in increasing in 2m air temperature over the Caribbean. The rise in extreme temperatures increases human discomfort and energy demands for air conditioning (AC) putting both the population and energy infrastructure at higher risk of vulnerability. This vulnerability is amplified in compact cities where anthropogenic heat removal from the built environment further increases the temperature of the urban canyon with feedback on human comfort and energy demands. Although there has been prior work reported on mitigating energy demands …

Utility-Scale Solar Pv Performance Enhancements Through System Level Modifications, Andrew D. S. Glick, Naseem Ali, Juliaan Bossuyt, Marc Calaf, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Performance of solar PV diminishes with the increase in temperature of the solar modules. Therefore, to further facilitate the reduction in cost of photovoltaic energy, new approaches to limit module temperature increase in natural ambient conditions should be explored. Thus far only approaches based at the individual panel level have been investigated, while the more complex, systems approach remains unexplored. Here, we perform the first wind tunnel scaled solar farm experiments to investigate the potential for temperature reduction through system-level flow enhancement. The percentage of solar irradiance converted into electric power depends upon module efficiency, typically less than 20%. The …

A Study On The Hydrodynamics Of A Bench-Scale Top-Fed Bubbling Fluidized Bed Gasifier Using Biomass And Coal As Feedstocks, Ali Can Sivri

Graduate Theses, Dissertations, and Problem Reports (ETD)

The production of synthetic gas (syngas) from renewable or carbon-neutral sources can significantly reduce greenhouse and other emissions associated with conventional fuels. One of the most promising technologies to efficiently convert carbonaceous feedstocks such as biomass, coal, or municipal waste into syngas for transportation, power, heat, electricity generation, and or production of added-value chemicals is the bubbling fluidized-bed gasifier (BFBG). However, the gasification process inside a BFBG is a very complex high-temperature multiphase flow phenomena still not well understood, particularly when binary mixtures are investigated. As a result, despite the numerous correlations in the literature developed to predict the hydrodynamics …

An Examination To Pathways Powering Car Using Clean Energy, Marina Miranda

Graduate Theses, Dissertations, and Problem Reports (ETD)

Traditional vehicles powered by internal combustion engines contribute significantly to increasing emissions of greenhouses gasses (GHG). There has been increasing interest in powering vehicles using green energy include using electricity produced by wind turbine and solar panel. The green electricity can be used to directly charge the Battery Electric Vehicles (BEV), or producing hydrogen as fuel for Fuel Cell Electric Vehicles (FCEV) by converting electrical energy to hydrogen (H₂) through water electrolysis. The low energy density H₂ produced can be stored on board as either compressed H₂ or liquefied H₂.

This research examines the …

Evaluation Of Process And Economic Feasibility Of Implementing A Topping Cycle Cogeneration System, Unique Karki

Graduate Theses, Dissertations, and Problem Reports (ETD)

Industrial applications that require steam for their end-uses generally utilize steam boilers that are at higher size than what is typically required. Similarly, gas turbine-based power plants corroborate the gas turbine system and eventually relieve the exhaust into the atmosphere. These facilities include food, paper, chemicals, refining, and primary metal manufacturing industries. This research focuses on the scope of a topping cycle combined heat and power (CHP) system by pushing the load on the boiler to a higher limit, or a gas turbine operation in place of a boiler system for a topping cycle CHP and its economic feasibility by …

Development Of An Activity-Based Windowing Approach To Evaluate Real-World Nox Emissions From Modern Medium And Heavy-Duty Diesel Trucks, Rasik Pondicherry

Graduate Theses, Dissertations, and Problem Reports (ETD)

The introduction of in-use emissions regulations by the United States Environmental Protection Agency (U.S.EPA) requires medium-duty (MD) and heavy-duty (HD) engine manufacturers to demonstrate emissions compliance during in-fleet operation. In the United States (U.S.), the Not-to-Exceed (NTE) method is used to evaluate real-world emissions compliance from on-highway MD and HD trucks. Regulatory agencies, engine manufacturers and research entities have identified that the NTE method incorporates numerous exclusions and evaluates emissions compliance only under selective operating conditions that are favorable for the selective catalytic reduction (SCR) system to reduce oxides of nitrogen (NOx) emissions efficiently. Such operation is typically encountered only …

Experimental And Computational Characterization Of Sodium Nitrate @ Silica Nano Capsules For Thermal Energy Storage Applications, Wataru Hashimoto

Graduate Research Theses & Dissertations

In this investigation, a nanocapsule composed of a sodium nitrate core and a silicon dioxide shell is synthesized, characterized, and analyzed utilizing a mixture of analytical and computational tools. The sol-gel method was selected as the process of nanoencapsulation. Analytical characterization techniques employed in this investigation include differential scanning calorimetry (DSC) to measure melting temperatures and enthalpies of fusion, dynamic light scattering (DLS) to calculate particle size distributions, scanning electron microscopy (SEM) to analyze surface characteristics, transmission electron microscopy (TEM) to perform shell characterization, and energy dispersive X-ray spectroscopy (EDS) to determine chemical composition. Preliminary results indicated a decrease in …

Numerical Investigation Of Darrieus Wind Turbine With Slotted Airfoil Blades, Ahmed Elbaz, Omar Sherif Mohamaed, Ahmed Abdelhamid Ibrahim, Ahmed Khaled Etman, Amr A. Abdelfattah

Mechanical Engineering

Low starting torque is considered as one of the major drawbacks of Darrieus type vertical axis wind turbine (VAWT). Design optimization to overcome this problem by modifying the airfoil geometry has received great attention by the wind energy community. Moreover, efforts have been directed towards augmenting the power coefficient of the turbine. In the present work, the effect of employing slotted airfoil as turbine blade on the performance and starting characteristics has been investigated. The slot parameters; slot location, angle of inclination, and dimensions, were optimized for NACA 0018 airfoil which is commonly used in Darrieus turbines. The flow over …

Carbon-Based Interlayers In Perovskite Solar Cells, Aleksandr P. Litvin, Xiaoyu Zhang, Kevin Berwick, Anatoly V. Fedorov, Weitao Zheng, Alexander V. Baranov

Articles

Perovskites are solution-processed, high-performance semiconductors of interest in low-cost photovoltaics. The interfaces between the perovskite photoactive layers and the top and bottom contacts are crucial for efficient charge transport and minimizing trapping. Control of the collection of charge carriers at these interfaces is decisive to device performance. Here, we review recent progress in the realization of efficient perovskite solar cells using cheap, easily processed, stable, carbon-based interlayers. Interface materials including graphene, carbon nanotubes, fullerenes, graphene quantum dots and carbon dots are introduced and their influence on device performance is discussed.

A Solar‐Driven Membrane‐Based Water Desalination/Purification System, Abdellah Shafieian Dastjerdi

Theses: Doctorates and Masters

Lack of fresh water has turned into one of the major challenges of the world in the present century. Desalination of brackish or seawater has been proven to be one of the best solutions to cope with this global challenge. Among all the desalination methods, Membrane Distillation (MD) is well known as a cost effective and profitable technology for treating saline water. However, higher energy consumption compared to other separation techniques has been reported as MD’s main drawback. That is why the application of solar energy to provide the thermal energy requirement of MD modules has been the focal point …

Measured And Modeled Performance Of A Spring Dominant Free Piston Engine Generator, Ramanjaneya Mehar Baba Bade

Graduate Theses, Dissertations, and Problem Reports (ETD)

Free Piston Engine Generators (FPEG) directly convert the reciprocating piston motion into electricity by using a linear alternator. Unlike conventional engines with piston motion restricted by a crankshaft mechanism, the FPEG piston motion is constrained by the energy available in the system. When stiff springs are considered in the design, the FPEG system attains high frequency with high power and efficiency. The main objective of this research was to model stiff spring-assisted FPEG system dynamics and performance accurately, and to apply the modeling results to the development of a 1kW, spark ignited, natural gas fueled, FPEG experimental prototype. The experimental …