Energy Systems Commons^™

An Examination To Pathways Powering Car Using Clean Energy, Marina Miranda

Graduate Theses, Dissertations, and Problem Reports (ETD)

Traditional vehicles powered by internal combustion engines contribute significantly to increasing emissions of greenhouses gasses (GHG). There has been increasing interest in powering vehicles using green energy include using electricity produced by wind turbine and solar panel. The green electricity can be used to directly charge the Battery Electric Vehicles (BEV), or producing hydrogen as fuel for Fuel Cell Electric Vehicles (FCEV) by converting electrical energy to hydrogen (H₂) through water electrolysis. The low energy density H₂ produced can be stored on board as either compressed H₂ or liquefied H₂.

This research examines the …

Carbon-Based Interlayers In Perovskite Solar Cells, Aleksandr P. Litvin, Xiaoyu Zhang, Kevin Berwick, Anatoly V. Fedorov, Weitao Zheng, Alexander V. Baranov

Articles

Perovskites are solution-processed, high-performance semiconductors of interest in low-cost photovoltaics. The interfaces between the perovskite photoactive layers and the top and bottom contacts are crucial for efficient charge transport and minimizing trapping. Control of the collection of charge carriers at these interfaces is decisive to device performance. Here, we review recent progress in the realization of efficient perovskite solar cells using cheap, easily processed, stable, carbon-based interlayers. Interface materials including graphene, carbon nanotubes, fullerenes, graphene quantum dots and carbon dots are introduced and their influence on device performance is discussed.

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Designing An Accessible Wave Energy Conversion Device For Powering Ocean Sensors, Sophie Coppieters ‘T Wallant

Independent Study Project (ISP) Collection

Currently, less than 5% of our oceans are comprehensively monitored and much more ocean data is needed to facilitate understanding of ocean physics, carbon cycling, and ocean ecosystems. Today, most autonomous ocean sensors are powered by primary battery, which have both limited capacity and lifetime. The goal of this research is to design a small, accessible renewable wave energy device to power autonomous free-floating ocean sensors. By designing a cheap, accessible, and simple wave energy converter, this work hopes to make ocean sensor deployment easier and cheaper for researchers, increase the lifetime of autonomous ocean sensors, and reduce the reliance …

Understanding Of The Ship Design Energy Efficiency And Its Implications In Practice, Haichao Yuan

Maritime Safety & Environment Management Dissertations (Dalian)

No abstract provided.

Design, Development And Implementation Of An Electrical Controller For A Solar-Electrical Collector, Sahar Mahboob, Razieh Pourdarbani, Bahman Behfar, Hossein Behfar

Emirates Journal for Engineering Research

Todays, maintaining atmospheric health is one of the most important prerequisites for sustainable global economic development, and the international community has no choice but to switch to renewable energies, including solar energy. The goal of the study was to provide a temperature of 60 ° C for drying summer fruits such as apricots therefore we investigated the effect of temperature control systems on the solar-electrical collector performance. Three LM35 temperature sensors were placed at 3 points of the collector (before the air inlet to the collector, after the air outlet from the collector and after heating elements) that were linked …

Swarm Behavior To Mitigate Rebound In Air Conditioning Demand Response Events, Jason Yasuto Kuwada

Boise State University Theses and Dissertations

Thermostatically Controlled Loads (TCLs) have shown great potential for Demand Response (DR) events. However, it has been commonly seen that DR events using TCLs may cause demand rebound, especially in homogeneous populations. To further explore the potential for DR events, as well as the negative effects, a stability and resilience analysis were performed on multiple populations and verified with agent based modeling simulations.

At the core of this study is an added thermostat criterion created from the combination of a proportional gain and the average compressor operating state of neighboring TCLs. Where DR events in TCLs are commonly controlled by …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

The Comparative Analysis Of The Performances Of Four And Six Pole Pairs Permanent Magnet Synchronous Generator, Ra Msuya

Tanzania Journal of Engineering and Technology (TJET)

Wind power applications using multi-poles permanent magnet generators have become very attractive especially in small ratings. Low-speed multi-pole PM generators are maintenance-free and may be used in different climate conditions. Most of the low speed wind turbine generators presented is permanent magnet machines, which have advantages of high efficiency and reliability since there is no need of external excitation and conductor losses are removed from the rotor. From the study two types of PM AC generator are designed with 6 pole pairs and the other one with 4 pole pairs. These generators were designed and analysed using Maxwell software. The …

Heat: Hydraulic And Electric Animation Team, Tyler J. Couvrette, Michael J. Cain, Sara T. Novell, Dexter K. Yanagisawa

Mechanical Engineering

Each New Years’ Day, the Cal Poly Rose Float presents a flower-covered float to the world at the Tournament of Roses parade. This floral display, paired with moving mechanical animations, shows off Cal Poly to the world. This project strove to keep Cal Poly on the cutting edge of technology both in parade floats, and in engineering, by creating a completely electric-powered animation system.

To accomplish this, a group of students set out to make the fully electric animation system that can power both the hydraulic and electric mechanisms on the Float. This was accomplished through months of planning and …

Exploring The Electrical Properties Of Twisted Bilayer Graphene, William Shannon

Senior Theses

Two-dimensional materials exhibit properties unlike anything else seen in conventional substances. Electrons in these materials are confined to move only in the plane. In order to explore the effects of these materials, we have built apparatus and refined procedures with which to create two-dimensional structures. Two-dimensional devices have been made using exfoliated graphene and placed on gold contacts. Their topography has been observed using Atomic Force Microscopy (AFM) confirming samples with monolayer, bilayer, and twisted bilayer structure. Relative work functions of each have been measured using Kelvin Probe Force Microscopy (KPFM) showing that twisted bilayer graphene has a surface potential …

Bgaas Alloy Semiconductors For Lasers On Silicon, Joshua Mcarthur

Mechanical Engineering Undergraduate Honors Theses

In the world of semiconductors today, there is a large dissonance between optical devices and electrical application. Due to the limitations of electron transport, photonic integrated circuits are soon-to-be vital in fields like telecommunications and sensing. Right now, these PIC’s are mostly made from indium phosphide. Due to its ubiquitous nature, however, there is a huge push to integrate efficient optics with silicon. It’s cheap, abundant, dope-able, and our electronic infrastructure is based on it. The reason why silicon photonics aren’t already commercialized is because of silicon’s indirect bandgap—it is inefficient with optical applications. The problem with combining direct gap …

Surface And Interface Properties In Thin-Film Solar Cells: Using Soft X-Rays And Electrons To Unravel The Electronic And Chemical Structure, Lothar Weinhardt, Dirk Hauschild, Clemens Heske

Chemistry and Biochemistry Faculty Research

Thin‐film solar cells have great potential to overtake the currently dominant silicon‐based solar cell technologies in a strongly growing market. Such thin‐film devices consist of a multilayer structure, for which charge‐carrier transport across interfaces plays a crucial role in minimizing the associated recombination losses and achieving high solar conversion efficiencies. Further development can strongly profit from a high‐level characterization that gives a local, electronic, and chemical picture of the interface properties, which allows for an insight‐driven optimization. Herein, the authors' recent progress of applying a “toolbox” of high‐level laboratory‐ and synchrotron‐based electron and soft X‐ray spectroscopies to characterize the chemical …

Energy Efficiency Evaluation Of Blower Heater Non-Purge Compressed Air Dryers, Alexandra M. Botts

Graduate Theses, Dissertations, and Problem Reports (ETD)

There are several compressed air dryers available for industrial use including, refrigerant, desiccant, and membrane. This research focuses on twin tower regenerative closed loop desiccant dryers, specifically: blower heater non-purge (BHNP) with and without cooling water pumps, Compressed-air Heater Purge (CHP), Blower Heater Purge (BHP), and Pressure Swing Heaterless (PSH). These styles of dryers are used mainly in industries that require extremely dry air such as, food manufacturing, medical air, or sensitive technology manufacturers. The research was conducted by collecting and analyzing real time current draw data on air compressors and associated dryers at eight different facilities (13 compressor systems) …

Networked Microgrid Optimization And Energy Management, Robert S. Jane

Dissertations, Master's Theses and Master's Reports

Military vehicles possess attributes consistent with a microgrid, containing electrical energy generation, storage, government furnished equipment (GFE), and the ability to share these capabilities via interconnection. Many military vehicles have significant energy storage capacity to satisfy silent watch requirements, making them particularly well-suited to share their energy storage capabilities with stationary microgrids for more efficient energy management. Further, the energy generation capacity and the fuel consumption rate of the vehicles are comparable to standard diesel generators, for certain scenarios, the use of the vehicles could result in more efficient operation. Energy management of a microgrid is an open area of …

Intelligent Application Of Flexible Ac Transmission System Components In An Evolving Power Grid, Robert Wall

Graduate Theses and Dissertations

The world revolves around energy and the energy sector is continually transforming and evolving. The status quo has been set by governing agencies in the United States for completely reliable power. The demand for energy efficiency continually rises for multiple reasons. Technology has improved for all sectors of the power grid, including renewable energy sources, fault protection, and SMART grid technology. The addition of new energy sources has led to the decommissioning of inefficient energy sources. The implementation of new technologies and power load on a large scale, coupled with the removal of grid stabilizers has posed different challenges that …

Cost Benefit Analysis Of Led Vs Florescent Lighting, Kurtis Clark, Phillip Humphrey

Student Research

Over the last few years, the state of Oklahoma has been looking at ways to reduce expenses to address concerns about a budget deficit. There have been efforts made to reduce expenses due to the use of energy. It has been said, when the lights are on, work is getting done. Running lights is therefore the cost of doing business. Our research examines the question, “is there a way to provide better lighting while operating at a lower cost.” This research examines the current lighting at Southwestern State University, primarily fluorescent lighting (FL), and a cost benefit analysis of switching …

Electrochemical Hydrogenation Of Acetone To Produce Isopropanol Using A Polymer Electrolyte Membrane Reactor, Chen Li, Ashanti M. Sallee, Xiaoyu Zhang, Sandeep Kumar

Civil & Environmental Engineering Faculty Publications

Electrochemical hydrogenation (ECH) of acetone is a relatively new method to produce isopropanol. It provides an alternative way of upgrading bio-fuels with less energy consumption and chemical waste as compared to conventional methods. In this paper, Polymer Electrolyte Membrane Fuel Cell (PEMFC) hardware was used as an electrochemical reactor to hydrogenate acetone to produce isopropanol and diisopropyl ether as a byproduct. High current efficiency (59.7%) and selectivity (>90%) were achieved, while ECH was carried out in mild conditions (65 degrees C and atmospheric pressure). Various operating parameters were evaluated to determine their effects on the yield of acetone and …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Low Voltage Ride Through Enhancement For Wind Turbines Equipped With Dfig Under Symmetrical Grid Faults, Francis Mwasilu

Tanzania Journal of Engineering and Technology (TJET)

In modern power systems with significant penetration of wind-turbines (WTs), improvement of low voltage ride through (LVRT) capability of WTs equipped with doubly-fed induction generators (DFIGs) is an important issue. Thus, this paper proposes a low voltage ride through (LVRT) strategy, which comprise of a capacitor connected in series with an inductor both connected in parallel to a resistor. The configuration is then connected to a small series resistor via a pair of antiparallel-Thyristors. The circuit and its switching control scheme of the proposed LVRT circuit are designed to: minimize the transition times, maintain the RSC connection to the rotor-windings, …

A Human Powered Micro-Generator For Charging Electronic Devices, John Adam

Senior Theses

A hand-pulled generator has been designed and tested. A preliminary result has been obtained and discussed. This device was created to provide outlet-free charging. Electronic devices are useful when going out into the wilderness. A portable power supply is necessary to keep an electronic device alive. This project created a device that converts human energy into electricity to charge electronic devices. This thesis overviews the device’s design, build, and tests. Two different tests were run to determine that the device is capable of charging the storage battery. The device presented can provide 14 minutes of charging time with one hour …

Measuring The Double Layer Capacitance Of Electrolyte Solutions Using A Graphene Field Effect Transistor, Agatha Ulibarri

Senior Theses

When operating graphene field effect transistors (GFETs) in fluid, a double layer capacitance (C_dl) is formed at the surface. In the literature, the C_dl is estimated using values obtained using metal electrode experiments. Due to the distinctive electronic and surface properties of graphene, there is reason to believe these estimates are inadequate. This work seeks to directly characterize the double layer capacitance of a GFET. A unique method for determining the C_dl has been implemented, and data has been obtained for three electrolytes and one ionic fluid. The results yield dramatically lower C_dl values than …

Mechanical And Electrical Characterization Of Carbon Fiber/Bucky Paper/Zinc Oxide Hybrid Composites, Suma Ayyagari, Marwan Al-Haik, Virginie Rollin

Publications

The quest for multifunctional carbon fiber reinforced composites (CFRPs) expedited the use of several nano reinforcements such as zinc oxide nanorods (ZnO) and carbon nanotubes (CNTs). Zinc oxide is a semi-conductor with good piezoelectric and pyroelectric properties. These properties could be transmitted to CFRPs when a nanophase of ZnO is embedded within CFRPs. In lieu of ZnO nanorods, Bucky paper comprising mat of CNTs could be sandwiched in-between composite laminae to construct a functionally graded composite with enhanced electrical conductivities. In this study, different configurations of hybrid composites based on carbon fibers with different combinations of ZnO nanorods and Bucky …

Communication Based Control For Dc Microgrids, Mahmoud S. Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

Centralized communication-based control is one of the main methods that can be implemented to achieve autonomous advanced energy management capabilities in DC microgrids. However, its major limitation is the fact that communication bandwidth and computation resources are limited in practical applications. This can be often improved by avoiding redundant communications and complex computations. In this paper, an autonomous communication-based hybrid state/event driven control scheme is proposed. This control scheme is hierarchical and heuristic, such that on the primary control level, it encompasses state-driven local controllers, and on the secondary control level, an event-driven MG centralized controller (MGCC) is used. This …

Optimal Operation Of Integrated Microgrids, Abdullah Albaker

Electronic Theses and Dissertations

Microgrids' deployments are increasing and projected to increase even more in future due to the significant advantages that are provided by this technology for end-use customers. However, microgrids can be connected to each other to create integrated microgrids system, which can further promote the anticipated and desired benefits. An integrated operation of microgrids can potentially improve the local power system reliability and resilience, increase the individual microgrids' economic benefits, and promote further utilization of renewable energy resources. Integrating microgrids, to achieve a microgrid network or cluster, is expected be an essential application towards smarter power grids and a key operational …

Predicting Energy And Water Consumption On Dairy Farms Through Statistical Analysis And Machine-Learning Methods, Philip Shine

Theses

With the abolishment of milking quotas across all European Union member states in April 2015, dairy farmers must adjust their farming practises to minimise milk production costs to adequately prepare for potential periods of reduced revenue. Milk production is an intense energy and water consuming process. Coupled with challenging European greenhouse gas reduction targets and legislation regarding the prevention of groundwater pollution and deterioration, increasing the production of milk in Ireland must be met with the sustainable consumption of on-farm energy and direct water resources, to ensure the future monetary and environmental sustainability of Ireland’s dairy industry. Thus, this body …

Hosting Capacity Optimization In Modern Distribution Grids, Mansoor T. Alturki

Electronic Theses and Dissertations

The availability of distributed renewable energy resources and the anticipated increase in new types of loads are changing the way electricity is being produced and supplied to consumers. This shift is moving away from a network delivering power solely from centralized power plants towards a decentralized network which supplements its power production by incorporating local distributed generators (DGs). However, the increased integration of DGs into existing distribution networks is impacting their behavior in terms of voltage profile, reliability, and power quality. To determine the maximum amount of DG that distribution grids can accommodate the concept of hosting capacity is introduced. …

Automated Cfd Optimization To Maximize Wind Farms Performance And Land Use, Rafael Valotta Rodrigues

Electronic Theses and Dissertations

In this research, a computational system was designed to analyze and optimize the layout of wind farms under variable operational conditions. At first, a wind turbine computational fluid dynamic (CFD) model was developed covering the near wake. The near wake flow field was validated against near wake velocity data from the MEXICO experiment. The CFD simulation demonstrated that the tip speed ratio and the pitch angle greatly influence the near wake behavior, affecting the velocity deficit and the turbulence intensity profile in this region. The CFD model was extended to cover the far wake, aiming to become a computational tool …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

The Impact Of Power Curve Estimation On Commercial Wind Power Forecasts - An Empirical Analysis, Gianni Goretti, Aidan Duffy, Tek Tjing Lie

Conference papers

An increasing number of utilities participating in the energy market require short term (i.e. up to 48 hours) power forecasts for renewable generation in order to optimize technical and financial performances. As a result, a large number of forecast providers now operate in the marketplace, each using different methods and offering a wide range of services. This paper assesses five different day-ahead wind power forecasts generated by various service providers currently operating in the market, and compares their performance against the state-of-the-art of short-term wind power forecasting. The work focuses on how power curve estimations can introduce systematic errors that …