Energy Systems Commons^™

High Energy And Power Density Peptidoglycan Musclesthrough Super-Viscous Nanoconfined Water, Haozhen Wang, Zhi-Lun Liu, Jianpei Lao, Sheng Zhang, Rinat Abzalimov, Tong Wang, Xi Chen

Advanced Science Research Center

Water-responsive (WR) materials that reversibly deform in response to humidity changes show great potential for developing muscle-like actuators for miniature and biomimetic robotics. Here, it is presented that Bacillus (B.) subtilis’ peptidoglycan (PG) exhibits WR actuation energy and power densities reaching 72.6 MJ m−3 and 9.1 MW m−3, respectively, orders of magnitude higher than those of frequently used actuators, such as piezoelectric actuators and dielectric elastomers. PG can deform as much as 27.2% within 110 ms, and its actuation pressure reaches ≈354.6 MPa. Surprisingly, PG exhibits an energy conversion efficiency of ≈66.8%, which can be attributed to its super-viscous nanoconfined …

Model Predictive Control Of Energy Systems For Heat And Power Applications, Chethan Ramakrishna Reddy

Dissertations, Master's Theses and Master's Reports

Building and transportation sectors together account for two-thirds of the total energy consumption in the US. There is a need to make these energy systems (i.e., buildings and vehicles) more energy efficient. One way to make grid-connected buildings more energy efficient is to integrate the heating, ventilation and air conditioning (HVAC) system of the building with a micro-scale concentrated solar power (MicroCSP) sys- tem. Additionally, one way to make vehicles driven by internal combustion engine (ICE) more energy efficient is by integrating the ICE with a waste heat recovery (WHR) system. But, both the resulting energy systems need a smart …

Torque Vectoring To Maximize Straight-Line Efficiency In An All-Electric Vehicle With Independent Rear Motor Control, William Blake Brown

Theses and Dissertations

BEVs are a critical pathway towards achieving energy independence and meeting greenhouse and pollutant gas reduction goals in the current and future transportation sector [1]. Automotive manufacturers are increasingly investing in the refinement of electric vehicles as they are becoming an increasingly popular response to the global need for reduced transportation emissions. Therefore, there is a desire to extract the most fuel economy from a vehicle as possible. Some areas that manufacturers spend much effort on include minimizing the vehicle’s mass, body drag coefficient, and drag within the powertrain. When these values are defined or unchangeable, interest is driven to …

Nonmetallic Jet Impingement Thermal Management For Power Electronics Via Additive Manufacturing, Reece Whitt

Graduate Theses and Dissertations

The increase in energy demanded by transportation and energy sectors has necessitated highly efficient thermal management for reliable power electronics operations. Conventional cooling techniques are limited by their inability to target switching location hot spot temperatures, leading to non-uniform thermal gradients. These devices, such as cold plates and heat sinks, also utilize heavy metallic structures that can accentuate electromagnetic interferences generated by high voltage switching processes. This work proposes a non-metallic jet impingement cooler for more customized thermal management, while simultaneously reducing the harmful effects of electromagnetic interferences. Additive manufacturing is utilized to enable jet impingement zones to target individual …

Performance Loss Rate And Temperature Modeling In Predictive Energy Yield Programs For Utility-Scale Solar Power Plants, Katelynn M. Dinius

Master's Theses

The Gold Tree Solar Farm, designed by REC Solar, has a rated output power of 4.5 MW and began operation in 2018 to provide electricity to Cal Poly’s campus. Gold Tree Solar Farm site terrain consists of rolling hills and uneven slopes. The uneven typography results in interrow shading, requiring a modified tracking control algorithm to maximize power production. Predicting a utility solar field’s lifetime energy yield is a critical step in assessing project feasibility and calculating project revenue. The MATLAB-based predictive power model developed for this field overpredicted power in the middle of the day. The purpose of this …

Assessment Of The Impacts Of Climate Variability On Hydropower Generation: A Case Study Of The New Pangani Falls, Tanzania, Dativa Byarufu

Tanzania Journal of Engineering and Technology (TJET)

Climate change poses potential impacts on hydropower generation either positively by increasing or negatively by decreasing river flow. This study assessed the impacts of climate variability on hydropower with a focus on the New Pangani Falls in Tanzania. Rainfall and temperature time series data from 1980-2014 were analyzed in relation to river discharge and associated impacts to hydropower generation. The Man-Kendall test was used to detect trend in both annual and seasonal time series. The results showed a negative trend in annual rainfall with Z= -2.41 at α = 0.05 and the slope Q = -0.964. Seasonal trend analysis showed …

An Improved Earned Value Management Method Integrating Quality And Safety, Brian Briggs

LSU Doctoral Dissertations

The construction industry invests significant time and money to improve quality and safety while reducing cost and schedule impacts. The industry has a sincere desire to improve construction project management methods to improve efficiency. Historically, quality and safety underperformances result from undermanaged quality control and safety activities. The cost and schedule impacts associated with poor quality work have always had an impact on construction operations. The unprecedented challenges and uncertainties of COVID-19 highlighted the need to improve the Earned Value Management (EVM) method within construction to reflect these quality and safety activities. The central goal of this dissertation is to …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Parametric Design Of Flywheel For An Electric Punch Press, Prashant Dhakal

Honors Theses

Almost all designs start with a design requirement. These may be weight, volume, clearance, and even custom calculations. Finding a solution that meets these requirements often involves tedious and time-consuming iterations. Once the solution has been found, the design must be optimized to find the best possible solution. Finding the ‘best possible design’ requires substantial time and effort dedicated to iterating and analyzing the potential model solutions. This is where Parametric design comes into play. The Parametric design aids in specifying the key parameters of the design and makes changes interactively, with the model updating automatically. The purpose of this …

Design Of Smart Trashcan, Haoran Song

Senior Theses

A smart trashcan has been designed which can bring convenience to people for throwing their garbage away during the COVID-19 pandemic. A prototype is made from cardboard to demonstrate its function. This trashcan can sense people who are coming and leaving, and it can open and close automatically. The trashcan is powered by solar energy. A solar panel is mounted on top of the trashcan supporter. This design is specifically for use in China.

Measurements Of Wind Turbine Wake Evolution And Trajectory During Morning Boundary Layer Transition And Under Wake Steering Conditions Via Unmanned Aerial Vehicles, Stewart Nelson

Theses and Dissertations--Mechanical and Aerospace Engineering

In July of 2019, a flight campaign was conducted using semi-autonomous Unmanned Aerial Vehicles (UAVs) at the Port Alma Kruger Energy wind farm in Ontario, Canada, to study various aspects of wind turbine wake evolution. Horizontal transects across the wakes were measured using modified fixed-wing aircraft fitted with a five-hole probe to measure the wind velocity vector. Reference boundary layer conditions were measured by an octocopter with an assortment of mounted sensors flying vertical profiles upstream of the turbines. Three experiments were conducted during the campaign, which consisted of a study on wake behavior during the morning boundary layer transition, …

Physics-Based Modeling Of Lithium-Ion Batteries For Control And Estimation Applications, Brody J. C. Riemann

Masters Theses

“Lithium-ion batteries are extensively used in many application areas like consumer electronics, electric vehicles, and microgrids. As the world moves towards further electrification of vehicles and more widespread use of renewable energy sources, the need for large-scale battery storage systems will grow. To effectively replace conventional methods, batteries will need to be charged quickly while accounting for degradation to maximize lifetime. Further, larger batteries require more detailed safety monitoring, which is implemented using a battery management system (BMS). A BMS is responsible for state of charge (SOC) estimation, state of health (SOH) estimation, cell balancing, regulating voltage and current according …

Fermentability Of Concentrated Sulfuric Acid Hydrolyzates From Aspenwood And Pinewood, Kando Janga

Tanzania Journal of Engineering and Technology (TJET)

The fermentability of hydrolyzates derived from two-stage concentrated sulfuric acid hydrolysis of Trembling aspen (Populus tremula) and Scots pine (Pinus sylvestris) were investigated. Three types of hydrolyzates were produced at mild, moderate and high decrystallization severity conditions. Portions of each of the original hydrolyzates were concentrated by vacuum evaporation to increase the sugar fraction to simulate industrial applications. Both sets of hydrolyzates were fermented anaerobically using Saccharomyces cerevisiae ATCC 96581. After 23 hours of fermentation, complete glucose consumption was observed for all the original hydrolyzates, with no signs of inhibition. The ethanol yields from these hydrolyzates ranged from 68% to …

Analysis Of Performance Characteristics Predicted From Several Experimental Data And Conversion Methods For Pumps As Turbine Application Using Statistical Techniques, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

Different performance characteristics have been indicated when running centrifugal pumps in the reverse direction. The water flows from the discharge side of the pump to the suction side to run in the reverse direction and generate the mechanical rotational energy for the micro-hydropower plant. The current study evaluates the extent of variation of performance characteristics predicted by several experimental data from different pump-specific speeds and conversion methods. The performance characteristics discussed include the head, flow rate, efficiency and specific speed. The flow rate and head of a pump operating in pump mode divided with the characteristic of the pump operating …

Potential For Increased Rural Electrification Rate In Sub-Saharan Africa Using Swer Power Distribution Networks, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

Rural electrification rate (RER) in Africa is still low to date. Several countries in Sub-Saharan Africa have tried to address this problem using conventional single phase two-wire or three-phase three-wire systems, however at large costs due to the nature of dispersed rural load centres, low load demand, and low population density. Another solution of off-grid generation creates associated health problems. Therefore, this paper undertakes a review of a single wire earth return (SWER) network as a RER improvement solution. The paper undertakes intensive literature review to elucidate challenges and solutions to the implementation of SWER technology. Advantages of SWER technology …

Wind Power Integration And Its Impact On Power Quality-A Didactic Approach, Santos Kihwele Dr

Tanzania Journal of Engineering and Technology (TJET)

This paper presents a model of a wind power system integrated with realistic power system, with intention of using it in addressing power quality issues in relations to grid codes during steady-state operation transient-state operation i.e., presence of grid fault events. For that case, a didactic approach of the normal performance of power systems due to the connection of fixed-speed wind turbine with induction generators is used. A study of integrating wind farms will be presented, including the incidence of high inrush current due to switching capacitor banks, out-rush current and voltage sags due to nearby three phase faults. As …

Solar Photovoltaic Performance Monitoring: A Bibliometric Review, Research Gaps And Opportunities, Javed Sayyad, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

Electrical power generation has been revolutionized by growing demand and use of Renewable Energy (RE) sources such as Solar Photovoltaic (SPV) as the main electricity source in modern times. The main objective of this bibliometric analysis is to understand the scope of the literature available for SPV performance characterization. This detailed reviewed was performed on the documents related to SPV research considering all the subject categories from Scopus and Web of Science (WoS) databases. The patterns for the particular set of keywords were broke down with the recuperated outcomes from Scopus database in the language, publication type, year of publication, …

Field Testing The Effects Of Low Reynolds Number On The Power Performance Of The Cal Poly Wind Power Research Center Small Wind Turbine, John B. Cunningham

Master's Theses

This thesis report investigates the effects of low Reynolds number on the power performance of a 3.74 m diameter horizontal axis wind turbine. The small wind turbine was field tested at the Cal Poly Wind Power Research Center to acquire its coefficient of performance, C­_p, vs. tip speed ratio, λ, characteristics. A description of both the wind turbine and test setup are provided. Data filtration and processing techniques were developed to ensure a valid method to analyze and characterize wind power measurements taken in a highly variable environment. The test results demonstrated a significant drop in the …

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

Modeling And Control Of Solar Pv With Battery Energy Storage For Rural Electrification, Irene Masenge

Tanzania Journal of Engineering and Technology (TJET)

In rural areas where electric power grid network is rarely available, power generation from renewable energy resource such as solar photovoltaic (PV) is mostly accomplished in standalone mode. The standalone solar PV system requires energy storage device to achieve reliable power supply to the end users. This paper presents modelling and coordination control of solar PV with battery energy storage system (BESS) for rural-electrification applications. The proposed control is accomplished via a bidirectional buck-boost converter with the objective of maintaining voltage at the DC bus constant. Simulation results based-on MATLAB/Simulink platform confirms good performance of the proposed system

Performance Analysis For Single-Stage And Multi-Stage Coreless Axial Flux Permanent Magnet Generator With Different Rotor Structures, Habib Asiful

Student Works (2020-2029)

Axial flux permanent magnet (AFPM) generator is a good candidate for both low and high-speed applications. Compared to radial flux machines, AFPM generators can be easily cascaded for enhanced power/torque while maintaining a fixed machine diameter. To improve power density and reduce cogging torque, some researchers have proposed the removal of iron core in the stator of AFPM machine, giving rise to the concept of coreless AFPM machine. Nevertheless, most of these coreless machines still require back iron on the rotor and/stator to reduce leakage flux. In this project, different rotor structures for single-stage coreless AFPM generators were considered, using …

An Integrated Resource Plan For Arizona Public Service Electric (Aps), Irene Boghdadi, Randy Chiu

Master's Projects and Capstones

Our Masters Capstone Project is an Integrated Resource Plan (IRP) for Arizona’s largest electric utility, Arizona Public Service Electric (APS).

An IRP is developed by utilities to identify the optimal combination of demand- and supply-side resources needed to reliably meet forecasted demand for energy and capacity, including a planning reserve margin, over a future period.

In addition to APS’s obligation to serve the growing load in Arizona while minimizing costs, it is required by the state to adhere to the Renewable Energy Standard (RES) policy of 15 percent retail sales from renewable energy resources by 2025.

The analysis described in …

Dartmouth Formula Racing: Full Electric Battery System Design, Matt Gardner, Jacob Hagler, Ruthie Nordhoff, Otto Salmi

ENGS 89/90 Reports

Dartmouth Formula Racing (DFR) lacked an electrical energy storage system that was Formula Hybrid rules-compliant, optimized for FH events, safe, reliable, and integrated with the rest of their vehicle. Additionally, the team lacked the academic and professional resources required to bring a thorough, analytical approach to the design, testing, and documentation of the new storage system. Our team designed and built a Lithium-Ion battery pack (accumulator) containing energy storage, active cooling, battery management and temperature monitoring systems, and control circuitry compatible with DFR’s vehicle. Collaboration throughout design, fabrication, assembly and testing processes ensured effective knowledge transfer to the DFR team.

Residential Thermal Storage And Cooling, Joao Marcelo Rocha Belmonte, Jacob Anderson, Andrew Clarke, Daphne Forester, Bianca Hardtke, Josh Hartman, Marc D. Compere

Sustainability Conference

No abstract provided.

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Development Of An Eco Approach And Departure Application To Improve Energy Consumption Of A Plug-In Hybrid Vehicle In Charge Depleting Mode, Brandon Narodzonek

Dissertations, Master's Theses and Master's Reports

A recent study at Michigan Technological University as part of the NEXTCAR DOE APRA-E Project was conducted to determine the potential energy savings of a plug-in hybrid electric vehicle (PHEV) equipped with various Connected and Automated Vehicle (CAV) Technologies. One aspect of this study focused on the development of an Eco Approach and Departure (Eco AnD) Application that would further reduce the energy consumed around a signalized intersection.

Many modern intersections are equipped with traffic signals that can broadcast Basic Safety (BSM), MAP, and Signal Phase and Timing (SPaT) message sets that contain intersection ID, location, current phase, and cyclic …

Real-Time Predictive Control Of Connected Vehicle Powertrains For Improved Energy Efficiency, Joseph Oncken

Dissertations, Master's Theses and Master's Reports

The continued push for the reduction of energy consumption across the automotive vehicle fleet has led to widespread adoption of hybrid and plug-in hybrid electric vehicles (PHEV) by auto manufacturers. In addition, connected and automated vehicle (CAV) technologies have seen rapid development in recent years and bring with them the potential to significantly impact vehicle energy consumption. This dissertation studies predictive control methods for PHEV powertrains that are enabled by CAV technologies with the goal of reducing vehicle energy consumption.

First, a real-time predictive powertrain controller for PHEV energy management is developed. This controller utilizes predictions of future vehicle velocity …

Internet Of Things In Sustainable Energy Systems, Abdul Salam

Faculty Publications

Our planet has abundant renewable and conventional energy resources but technological capability and capacity gaps coupled with water-energy needs limit the benefits of these resources to citizens. Through IoT technology solutions and state-of-the-art IoT sensing and communications approaches, the sustainable energy-related research and innovation can bring a revolution in this area. Moreover, by the leveraging current infrastructure, including renewable energy technologies, microgrids, and power-to-gas (P2G) hydrogen systems, the Internet of Things in sustainable energy systems can address challenges in energy security to the community, with a minimal trade-off to environment and culture. In this chapter, the IoT in sustainable energy …