Energy Systems Commons^™

Energy From Chemical Reactions: Understanding The Combustion Engine, Tammy Guthrie, Kathy Prophet, Greg Herzig, Cassie Kautzer

Middle School Lesson Plans

Automobiles produce a large amount of heat generated by the burning of gasoline. Burning gasoline is a chemical reaction that causes a phase change. This is called combustible energy. During combustion fuel combines with oxygen to release energy (such as heat, light, sound) along with another product that is often considered waste. Most of the energy produced is not used to power the automobile, but is released as heat. 19.3 pounds of the greenhouse gas, carbon dioxide, is produced from the combustion of 1 gallon of U.S. gasoline according to the U.S. Energy Information Administration.

Kinetic Energy Investigation, Mike Jackson

High School Lesson Plans

Students will build a mouse trap powered car that converts elastic potential energy contained in the trap’s spring to linear kinetic energy of the car. The release of this energy results in a net force which leads to linear acceleration. This acceleration can be measured with Vernier Logger Pro®, and using Newton’s Second Law of Motion, the net force can be calculated. Finally, using the concept of work, the final kinetic energy of the car can be calculated. Once students become familiar with the calculation of work and energy, the teacher will challenge the students to modify their cars to …

Design And Manufacture Of A Waste Compactor Prototype: A Step Towards Implementing A Non-Burn Health Care Waste Disposal In Developing Countries, Tito Mwinuka

Tanzania Journal of Engineering and Technology (TJET)

Non-burn technology is the only safe way of handling and disposing infectious healthcare waste. It involves steam treatment of infectious waste at temperatures higher than 121 o C for a minimum of 30 minutes before disposing them just like other municipal waste. Infectious healthcare waste is normally only about 10 25% of all healthcare waste. In this paper, design, manufacturing and testing of a waste compactor for reducing waste volume to facilitate its handling is discussed. Preliminary tests show that the waste volume can be reduced to less than 10% of its original volume using the developed compactor. Waste compactors …

Are Solar Panels A Viable Power Source For A Green Energy Vehicle?, Mason C. Adams

Senior Theses

A solar cell powered go-kart has been built and tested. The result shows using solar energy alone cannot meet the requirement of running a regular passenger car. This is due to the limited surface area of the passenger car. This thesis also discusses the operating principles of solar panels, the physics of P type and N type semiconductors, and the formation of the PN junction, as well as the solar current. Modifications of an existing go-kart are described in detail in this thesis. Suggestions for making green vehicles are discussed as well.

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

Solar Irradiance Forecasting And Implications For Domestic Electric Water Heating, Christopher Nutter

College of Graduate Studies: Theses & Dissertations

As the effects of burning fossil fuels continues to present its prevalence, the interests in alternative forms of energy is expanding. Within the home, the domestic electrical water heater accounts for approximately 17% of its energy consumption. Reducing the amount of energy required to produce hot water from this thermal system alone can have a significant effect on reducing its carbon footprint. In this presented work, a modeled domestic electrical water heater was supplied photovoltaic and on-grid electrical power to increase its energy efficiency. As photovoltaic (PV) energy is directly related to solar irradiation, it is important to receive accurate …

Design Of Electrical Layout Of Offshore Wind Farms, Shirshak K. Dhali, Mahidhar Nandigam

Electrical & Computer Engineering Faculty Publications

The cost and efficiency of offshore wind farms are determined by a variety of factors which include the type of electrical system (AC or DC), transmission length, transmission voltage, rated power, wind turbine type, farm topology, and wind speed. Since the design variable space is large for such problems, computational optimization is necessary to find an optimal solution. This paper discusses a design methodology to determine the optimal values of components to minimize the cost of an offshore wind farm. The cost, loss, reliability models, and the application of geometric programing for optimization of the layout and configuration of an …

Model-Based Control Of Hybrid Electric Powertrains Integrated With Low Temperature Combustion Engines, Ali Soloukmofrad

Dissertations, Master's Theses and Master's Reports

Powertrain electrification including hybridizing advanced combustion engines is a viable cost-effective solution to improve fuel economy of vehicles. This will provide opportunity for narrow-range high-efficiency combustion regimes to be able to operate and consequently improve vehicle’s fuel conversion efficiency, compared to conventional hybrid electric vehicles (HEV)s. Low temperature combustion (LTC) engines offer the highest peak brake thermal efficiency reported in literature, but these engines have narrow operating range. In addition, LTC engines have ultra-low soot and nitrogen oxides (NOx) emissions, compared to conventional compression ignition and spark ignition (SI) engines. This dissertation concentrates on integrating the LTC engines (i) in …

Photovoltaic Cooking In The Developing World, Tyler Watkins, Christopher O'Day, Omar Arriaga

Mechanical Engineering

The challenge of clean cooking is faced by hundreds of millions of people worldwide. We present a cooking technology consisting of a solar panel directly connected to an electric heater in a well-insulated chamber. Assuming continued decrease in solar panel prices, we anticipate that in a few decades Solar Electric Cooking technologies will be the most common cooking technology for the poor. Appropriate use of insulation reduces the power demand making low-power Insulated Solar Electric Cooking systems already cost competitive.

Wake Character In The Wind Turbine Array: (Dis-)Organization, Spatial And Dynamic Evolution And Low-Dimensional Modeling, Nicholas Michael Hamilton

Dissertations and Theses

To maximize the effectiveness of the rapidly increasing capacity of installed wind energy resources, new models must be developed that are capable of more nuanced control of each wind turbine so that each device is more responsive to inflow events. Models used to plan wind turbine arrays and control behavior of devices within the farm currently make questionable estimates of the incoming atmospheric flow and update turbine configurations infrequently. As a result, wind turbines often operate at diminished capacities, especially in arrays where wind turbine wakes interact and inflow conditions are far from ideal. New turbine control and wake prediction …

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

How Can Occupancy Modeling And Occupancy Sensors Reduce Energy Usage In Academic Buildings: An Application Approach To University Of San Francisco, Paloma R. Duong

Master's Projects and Capstones

Buildings are amongst the highest energy consumers relative to industry and transportation. They account for 40% of the world’s energy consumption, due to the need for lighting, equipment, heating, cooling and ventilation. Academic buildings are multi-purpose buildings that create a challenge on energy reduction. Most are old and have fixed occupancy schedules, resulting in high energy consumption because these buildings experience significant occupancy variation throughout the day. Five academic buildings were analyzed; their building information, energy consumption data and methods to project energy savings have been analyzed. The case studies presented different strategies on predicting energy savings, but these have …

Solar Photovoltaic System Control Topology Investigation For Power Source Mismatch, Lynette O'Callaghan

Conference papers

An investigation into solar photovoltaic (PV) system control topology selection, when partial shade is anticipated in the solar array, is presented. As available area is maximised in Building Integrated PV (BIPV) systems, shading is an inevitable consequence. The presence of partial shading in a PV array leads to multiple power peaks in the power-voltage curve, due to bypass diode sections being triggered, and an increase in module mismatch losses in the array. A building energy design software, Integrated Environmental Solutions, is used to determine the shadowed area on PV modules throughout the year, incorporating the PV system location and geometrical …

Using Photovoltaics To Power Electrochemical Chloride Extraction From Concrete, Sean Bond, Lynette O'Callaghan, Niall Holmes Dr., Brian Norton

Conference papers

Corrosion of embedded steel in reinforced concrete (RC) is a world-wide problem, that reduces structural performance and lifespan. Chloride attack may be a result of seawater, de-icing salts or contaminated admixtures, brought on by ingress of chlorides into the concrete. Electrochemical Chloride Extraction (ECE) is a non-destructive treatment for contaminated RC structures, that due to uncertainty of treatment times and applied current densities, is only 50% effective. It is often diesel powered has an environmental impact and often very costly due to the long treatment times. To improve the efficiency of ECE the influences of concrete resistance, cement type and …

Predictive Control Of Power Grid-Connected Energy Systems Based On Energy And Exergy Metrics, Meysam Razmara

Dissertations, Master's Theses and Master's Reports

Building and transportation sectors account for 41% and 27% of total energy consumption in the US, respectively. Designing smart controllers for Heating, Ventilation and Air-Conditioning (HVAC) systems and Internal Combustion Engines (ICEs) can play a key role in reducing energy consumption. Exergy or availability is based on the First and Second Laws of Thermodynamics and is a more precise metric to evaluate energy systems including HVAC and ICE systems. This dissertation centers on development of exergy models and design of model-based controllers based on exergy and energy metrics for grid-connected energy systems including HVAC and ICEs.

In this PhD dissertation, …

Industrial Energy Consumption, Benchmarking, And Analysis In The United States, Daniel Maldonado

Mechanical Engineering Undergraduate Honors Theses

The purpose of this paper is to analyze the energy consumption of the industrial sector in the United States, and to identify the tools that can be used to minimize the consumption and improve the energy efficiency of all facilities in the country. The first part of the paper is a historical analysis of the industrial sector energy consumption, where the different energy sources are identified. The second part details different electronic tools that will provide facilities the ability of performing benchmarking, in order to understand their energy performance. Finally, the third part of this paper provides information about the …

Cultural Change Through Bim: Driving Lean Transformation In Education, Avril Behan, Malachy Mathews, Kevin Furlong, Ciara Ahern, Una Beagon, Peter Brennan, Colin Conway, Lee Corcoran, Pierce Fahy, Alan Hore, Barry Mcauley, Trevor Woods

Conference papers

This paper presents a case study of how the adoption of BIM-based practices in the AECO industry is being reflected by cultural change in higher education in Ireland. The silo-mentality that has dominated the AECO sector for more than a century has, despite numerous reorganisations, been replicated in the structures of educational institutions, including in Dublin Institute of Technology since the inception of its founding colleges in the late 1800s. Most AECO programmes must include content that is external to the programme’s specific discipline. Through the School structures of the Institute, delivery of such content is known as "service teaching" …

Shark Alert: Early Warning System, Cory Peterson, Marc Rauschnot, Taylor Mcclain

Electrical Engineering

The Shark Alert Early Warning System is a device geared toward avid beach goers such as surfers, divers, and swimmers. The system is composed of an ultrasonic transmitter mounted on a shark’s dorsal fin and a receiver worn by the user around the ankle. The receiver alerts the user to the presence of a shark upon ultrasonic signal detection.

The receiver warns the user through both visual and tactile (vibration) alerts to ensure user notification. This circuit was built and tested in the EE labs and Recreation Center pools to determine transmission range. The receiver detects the transmitted signal up …

Experimental Verification And Integration Of A Next Generation Smart Power Management System, Tavis Clemmer

Graduate Theses and Dissertations

With the increase in energy demand by the residential community in this country and the diminishing fossil fuel resources being used for electric energy production there is a need for a system to efficiently manage power within a residence. The Smart Green Power Node (SGPN) is a next generation energy management system that automates on-site energy production, storage, consumption, and grid usage to yield the most savings for both the utility and the consumer. Such a system automatically manages on-site distributed generation sources such as a PhotoVoltaic (PV) input and battery storage to curtail grid energy usage when the price …

Vortex Identification In The Wake Of A Wind Turbine Array, Aleksandr Sergeyevich Aseyev

Dissertations and Theses

Vortex identification techniques are used to analyze the flow structure in a 4 x 3 array of scale model wind turbines. Q-criterion, Δ-criterion, and λ₂-criterion are applied to Particle Image Velocimetry data gathered fore and aft of the last row centerline turbine. Q-criterion and λ₂-criterion provide a clear indication of regions where vortical activity exists while the Δ-criterion does not. Galilean decomposition, Reynolds decomposition, vorticity, and swirling strength are used to further understand the location and behavior of the vortices. The techniques identify and display the high magnitude vortices in high shear zones resulting from the …

Global Time-Independent Agent-Based Simulation For Transactive Energy System Dispatch And Schedule Forecasting, Shawn Aaron Chandler

Dissertations and Theses

Electricity service providers (ESP) worldwide have increased their interest in the use of electrical distribution, transmission, generation, storage, and responsive load resources as integrated systems. Referred to commonly as "smart grid," their interest is driven by widespread goals to improve the operations, management and control of large-scale power systems. In this thesis I provide research into a novel agent-based simulation (ABS) approach for exploring smart grid system (SGS) dispatch, schedule forecasting and resource coordination. I model an electrical grid and its assets as an adaptive ABS, assigning an agent construct to every SGS resource including demand response, energy storage, and …

Loss Modeling Of A Permanent Magnet Dc Motor Drive Water Pumping System, Nelson Lujara

Tanzania Journal of Engineering and Technology (TJET)

The paper presents an analytical approach to the determination of losses in each of the sub-systems of the Photovoltaic (PV) Permanent Magnet DC Motor (PMDC) drive water pumping system with and without maximum power tracking. The losses of the system at varying heads are firstly, determined using parameters from the data sheets and then validated by experimental results. The results are used to establish the head and the flow rate optimal operating point of the system.

Anisotropy Of The Reynolds Stress Tensor In The Wakes Of Counter-Rotating Wind Turbine Arrays, Nicholas Michael Hamilton

Dissertations and Theses

A wind turbine array was constructed in the wind tunnel at Portland State University in a standard Cartesian arrangement. Configurations of the turbine array were tested with rotor blades set to rotate in either a clockwise or counter-clockwise sense. Measurements of velocity were made with stereo particle-image velocimetry. Mean statistics of velocities and Reynolds stresses clearly show the effect of direction of rotation of rotor blades for both entrance and exit row turbines. Rotational sense of the turbine blades is visible in the mean spanwise velocity W and the Reynolds shear stress -[macron over vw]. The normalized anisotropy tensor was …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Faculty Publications

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

Modeling Of Chemical-Mechanical Couplings In Anode-Supported Solid Oxide Fuel Cells And Reliability Analysis, Xinfang Jin, Xingjian Xue

Faculty Publications

Oxygen ionic transport in conducting ceramics is an important mechanism enabling solid oxide fuel cell (SOFC) technology. The multi-physicochemical processes lead to the fact that the distribution of oxygen vacancy site fraction is not uniform in a positive-electrode electrolyte negative-electrode (PEN) assembly. Different oxygen vacancy concentrations induce different volumetric expansion of ceramics, resulting in complicated chemical–mechanical coupling phenomena and chemical stress in SOFCs. In this research, a mathematical model is developed to study oxygen ionic transport induced chemical stress in an SOFC. The model is validated using experimental polarization curves. Comprehensive simulations are performed to investigate chemical stress distribution in …

Analysis Of Power Efficiency Of A Direct-Driven Locally Fabricated Permanent Magnet Ac Generator For Small-Scale Wind Power Applications In Tanzania, Mussa Iddi Mgwatu Dr.

Tanzania Journal of Engineering and Technology (TJET)

The use of direct-driven permanent magnet alternating current (AC) generators offers the opportunity to reduced costs and increased system efficiency. This type of generator could be the best alternative for rural population whom are not connected to the national grid. To improve the design and efficiency of locally fabricated generators, it is imperative to characterize both their mechanical and electrical parameters. This paper presents the analysis of power efficiency of the synchronous permanent AC generator locally fabricated in Tanzania. In this case, load resistance and rotational speed are characterized using designed experiment. The output current and voltage of the generator …

Heating Effects Through Harmonic Distortion On Electric Cables In The Built Environment, Kevin O'Connell

Doctoral

Under ideal circumstances, electric power supply voltage and current waveforms should be sinusoidal. However, this is very seldom the case in the built environment, due to the proliferation of non-linear loads. Examples of non-linear loads are those containing switched mode power supplies, reactors and electronic rectifiers/inverters. Common devices such as personal computers, fluorescent lighting, electric motors, variable speed drives, transformers and reactors and virtually all other electronic equipment are examples of non-linear loads. Non-linear loads are the norm in the built environment rather than the exception. Such loads produce complex current and voltage waves and simple spectral analysis of these …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Design Of An Energy Efficient Virtual End Node Client Using Openadr2.0a And Smap, Kevin Navero

BioResource and Agricultural Engineering

Demand Response (DR) describes the set of actions taken to impose a reduction in electrical loads to stabilize the power grid and decrease costs. It is used when power grid emergencies or extremely high demand and congestion, threaten the electricity supply-demand balance. Automated Demand Response (ADR) describes a web-based control system that triggers DR events automatically by signaling other pre-programmed control systems. This project intends to use the OpenADR2.0 specifications provided by the OpenADR Alliance to construct an open source Virtual End Node (VEN) client to retrieve DR signals. The Simple Measurement and Actuation Profile (sMAP) software is also used …

Low Speed Alternator Design, Scott Merrick

Electrical Engineering

No abstract provided.