Electro-Mechanical Systems Commons^™

Pre-Programmable Directional Stiffness In Continuum Robotic Arms: Effects Of Truss Configurations, Mostafa Abdelaziz, Zahy Elgendy, Mahmoud Magdy

Mechanical Engineering

This paper investigates the implementation of trussed designs in modular tendon-driven continuum arms (CAs) to address stiffness and stability limitations while maintaining adaptability. Various truss configurations— Single-Level, Combined-Level, and Alternated trusses—were analyzed using Finite Element Analysis (FEA) to evaluate their impact on flexural and axial stiffness under realistic loading conditions. Results demonstrate that truss placement significantly influences performance, with bottom-level trusses improving flexural stiffness by up to 33%, middle-level trusses enhancing axial stiffness by 43%. Further, Combined-Level configurations provide superior overall stiffness, with MiddleBottom trusses achieving a 66.5% improvement in flexural stiffness and a 70.9% increase in axial stiffness, while …

Pseudo Gps For Romi, Emmanuel Baez, Owen Guinane, Gabriel Coria, Conor Schott

Mechanical Engineering

The Pseudo-GPS system for Romi robots addresses the need for precise real-time location tracking in Cal Poly's Mechatronics lab. This project, developed by Emmanuel Baez, Gabriel Coria, Owen Guinane, and Conor Schott, under the guidance of instructor Charlie Refvem, provides a proof-of-concept system to enhance the Romi robots' geolocation capabilities for advanced robotic algorithms.

The proposed system uses a Raspberry Pi 4 equipped with a Pi camera module and ArUco markers to track the position and orientation of Romi robots within a lab environment. Custom 3D-printed stands secure markers on the robots, and a designated origin marker defines the coordinate …

A Case Study On Optimizing Industrial Air Conditioning With Thermal Solar Energy In Egypt, Tamer Adel Mohamed, Hesham Safwat, Mohammed A. Ebaid

Mechanical Engineering

This study investigates the feasibility of implementing a solar-assisted adsorption chiller in an industrial building at the Oriental Weavers International factory located in 10th of Ramadan City, Cairo, Egypt. The objective is to replace an inefficient split air conditioning system currently used to cool the Jacquard units during carpet manufacturing. The research begins by analyzing the performance of the existing cooling system to establish a baseline. It then explores the potential energy savings achievable by replacing the current system with a solar-assisted adsorption chiller. The existing oversized boiler will serve as an auxiliary heater for the new system. TRNSYS simulation …

Spring Rate Measurement Of A Pneumatic Mountain Bike Tire, Joseph D. Balderama, Alexandre Kachlakev, Duncan Wyke, Luki Rosen

Mechanical Engineering

The Final Design Review (FDR) presents a comprehensive overview of the spring rate measurement project for a pneumatic mountain bike tire. This report details the project's design, its implementation, and how it met all specified requirements. It also includes a discussion of the project's findings and recommendations for future work, assuming continuation of the project. The primary goal is to develop a device that allows professional race teams or experienced mountain bike riders to parameterize tires based on their spring rate in addition to internal pressure.

Since the Critical Design Review (CDR), the design has undergone significant changes due to …

Rapid Composter, Cate Seay, Clarisbet De Jesus, Lesley Milena Estrada, Reese Dennett

Mechanical Engineering

This Final Design Review documents the efforts of a team of mechanical engineering students from California Polytechnic State University, San Luis Obispo as they work towards completing their assigned senior design project. This team was tasked with designing and developing an onsite rapid composter for the Girl Scouts of California’s Central Coast. The selected design concept that will be explained focuses on creating a composter that is child-safe, portable, weatherproof, solar-powered, and requires minimal manual user input. This report will not only provide a detailed description of the chosen design but will also supply an extensive design justification. This mainly …

F56: Rocket Thrust Vector Control, Ethan Douglas Anderson, Yiming Trent Jia, Sahil Sampat

Mechanical Engineering

This Final Design Review (FDR) report compiles relevant information regarding the Rocket Thrust Vector Control senior project as sponsored by Ethan Anderson from Cal Poly Space Systems (CPSS). Documented in this report is our progress from the months following our Critical Design Review (CDR) completion. This consists of a brief overview of the design our thrust vector control (TVC) system and its subassemblies with design changes noted, a thorough walkthrough of our procurement, manufacturing, and assembly process for creating our verification prototype (including software), a breakdown of how we verified each of our specifications through inspection and testing and the …

Cal Poly Battle Bot (F41), Jyotaaver S. Nirula, Andrew D. Peterson, Johnathan W. Waldmire, Nathaniel Ab Davis

Mechanical Engineering

This senior project endeavored to design, construct, and optimize a 120lb robot combatant tailored for the competitive arena of combat robotics. The project is a collaborative effort between mechanical, computer, and electrical engineering students at Cal Poly, combining diverse expertise to achieve a unified goal. Our competition, RoboGames, was in April of this year in Northern California.

The mechanical engineering team assumed primary responsibility for the physical components of the battle bot, focusing on three pivotal components: a robust drivetrain, armor, and a highperformance vertical spinner. These elements constitute the foundation of the battle bot's offensive and defensive capabilities, crucial …

Cal Poly Battle Bot, Jyotaaver S. Nirula, Johnathan W. Waldmire, Andrew D. Peterson, Nathaniel Ab Davis

Mechanical Engineering

This senior project endeavored to design, construct, and optimize a 120lb robot combatant tailored for the competitive arena of combat robotics. The project is a collaborative effort between mechanical, computer, and electrical engineering students at Cal Poly, combining diverse expertise to achieve a unified goal. Our competition, RoboGames, was in April of this year in Northern California.

The mechanical engineering team assumed primary responsibility for the physical components of the battle bot, focusing on three pivotal components: a robust drivetrain, armor, and a highperformance vertical spinner. These elements constitute the foundation of the battle bot's offensive and defensive capabilities, crucial …

Nsf-Eri Evolution Of Liquid Sheet Edges Project: Soap Film Frame Withdrawal And Positioning Apparatus, Samir S. Patel, Sophia Young, Nicole N. Morgan

Mechanical Engineering

The experimental investigation of instabilities along retracting liquid sheet edges seeks to answer a fundamental fluid mechanics question. We’ve successfully delivered an experimental apparatus to conduct research and answer this question. This document chronicles a design overview of our apparatus, our manufacturing process, our design verification, and recommendations for future steps. The final product is a document outlining our final design (i.e., our ‘Final Design Review’ (FDR)).

Autolacing The Dml, Harrison Hong, Chanh Tu Derek Lam, Candice Espitia, Paolo Navarro

Mechanical Engineering

The design challenge present is the design of a system to efficiently speed up the lacing of the dry mat loop (DML), part of the GAF production line. For this year, the scope of the project focuses on research and creating a proof of concept for the mechanism responsible for moving the mat within the DML. Compiled research focuses on competitor solutions, material properties, and possible mover mechanisms to be integrated into the major design. Competitor solutions provide an idea of raw material manipulation options. Material properties and possible mover mechanisms provide the foundation for ideation and concept prototyping. The …

Robot Rodeo, Daniel Rickers, Tyler Vaughn, Vinayak Sharath, Berent Baysal, Promit Das Gupta

Mechanical Engineering

This document outlines the Final Design Review (FDR) for an autonomous robot developed in response to the Naval Surface Warfare Center (NSWC) Ship Maintenance Robot Rodeo Challenge. Through extensive analysis, we selected a design concept, built a verification prototype, and tested the prototype in the NSWC Robot Rodeo Competition. The design overview portion of this report will present the details of our design while explaining how it will function. Next, is our implementation section, which provides evidence about our procurement, manufacturing, and assembly of our product. Our design verification follows and explains the tests that we conducted on the robot …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Cnc Retrofits, Fabian Samano, Murat Askin, Daniel Lonczak, Zane Campise

Mechanical Engineering

The Boxford CNC Lathe is a machine used for educational purposes. The goal of the CNC Retrofits project is to improve the Boxford MT2’s performance and functionality to enable Mr. Lonczak to manufacture customized ballpoint pens. Within this Final Design Review (FDR) document, we present design updates since the CDR and implementation/assembly techniques. This work culminates in a solution to Mr. Lonczak’s needs which is analyzed in three subsystems: main control, spindle position tracking, and user interface. Within this report, we show the results of each subsystem’s verification process. These results prove that the design concept was met by describing …

Tagalong Trail, Sean Wahl, Jason Davis, Quinlan Stephens, Ryan Johnson, Vinh Vo

Mechanical Engineering

The Cal Poly mechanical engineering team working on the Path of Lights and Sounds for the Girl Scouts of California’s Central Coast has now completed their project. In the last quarter of their project, they were able to finalize their tile’s structural design while iterating through several electronics board designs. Through this iteration, they were able to create a final electronics board and designed a water-resistant enclosure to house the board. A new team member was added, allowing them to manufacture 28 tile structures and 30 electronics assemblies over the course of two and a half weeks. This proved to …

Integrated Actuator, David Hefter, Mathew Smith, Amanda Westmoreland, Akanksha Maddi

Mechanical Engineering

This Final Design Review document outlines the senior project design that we, a team of four mechanical engineering students at California Polytechnic State University, are developing for Charlie Refvem, a lecturer in the mechanical engineering department. The final design has undergone significant modifications since the Critical Design Review, such as a redesigned vertical shaft, material changes, and the incorporation of belt tensioners. These redesigns are thoroughly discussed in the context of testing and assembly error resolution.

The document outlines the detailed steps for the production and testing of the design verification prototype. This includes the procurement and manufacturing of components, …

Northrop Grumman Collaboration Project, Nikkia Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake

Mechanical Engineering

The Northrop Grumman Collaboration Project (NGCP) is a collaborative club project sponsored by Northrop Grumman for the students of Cal Poly San Luis Obispo (CPSLO) and Cal Poly Pomona (CPP) to create a fleet of vehicles to aid in the simulated rescue of stranded hiker. The CPSLO club is responsible for delivering an autonomous flight vehicle that can suppress a fire and retrieve a payload. Mechanical Design Team of the CPSLO team was responsible for the design of the frame, electronics housing, and payload and fire suppression systems.

Animatronic Monarch Butterfly: Mechanical System, Janine Rae Moreno, Enrico Cruz, Alexia Murphy, Lakshmanan Muthukaruppan

Mechanical Engineering

This report describes the design, manufacturing, and design verification of an interactive animatronic monarch butterfly created by a team of mechanical and computer engineering students for the Girl Scouts of California's Central Coast. The purpose of the project is to engage Girl Scouts in learning about monarch butterflies and provide hands-on experience in robotics and STEM. The report covers design changes, manufacturing processes, and assembly of various components, including the butterfly body, wings, legs, and electronic housing. The software and electronics used in the project are also briefly discussed, as the computer engineering team was responsible for the software and …

Weed Robot, Kaela Stern, Lewis Kanagy, Claire Franz, Carlos Rodriguez Orozco, Jackie Chen, Sachi Hiji, Ayush Kakkanat, William Ta

Mechanical Engineering

Team Weed Scouts has completed our work on a weed-cutting robot for the Girl Scouts of California’s Central Coast. The final robot build provides a solid foundation that can be built and improved upon by future teams. We have completed the robot base and structure, including the chassis, drivetrain, and robot shell. We also completed manufacturing a weed storage bin and canvas cover for the robot. Additionally, we have built a weed scooper, the mechanism that cuts weeds and transports them into a storage compartment. The electronics and programming for remote control of the robot are also implemented. After some …

In-Situ Mechanical Tester, Andrrew Murach, Gustavo Marquez, Kosimo Tonn, Jake Vormbaum

Mechanical Engineering

Over the course of the 2022-23 Cal Poly SLO school year, a small tensile tester device was developed specifically for Dr. Long Wang to test thin film materials under a microscope and generate accurate force versus displacement graphs. A tensile tester was manufactured using purchased and machined components, electronics were consolidated in a separate box and connected, and a program and user interface were written to control the motion, provide custom inputs, and organize useful data for the researcher. Tests were conducted to compare the performance of the device to universal tensile testers available in the Composites lab. The device …

Baja Sae Semi-Active Suspension, Cameron Paul Jones, Ethan Jacobi Mikel, Joshua Macguire Wright, Aditya Garg

Mechanical Engineering

This document outlines the design and justification for the final design of the Baja SAE Semi-Active Suspension Senior Project. The goal of the project was to build a base valve that can adjust suspension damping rates on the fly. This document details the ideation, design, manufacturing, design verification results, and detailed drawing package for the project. Additionally, this document includes information regarding the pressure drop calculator, O-ring calculations, and CAD. The manufacturing processes used to create the valve and the testing and evaluation of the valve are included as well. Finally, the methods that were used to manage this project …

Rapid Composter, Shannon Shinozaki, Avin Atencio, Jonathan Fraser, Lukas Kolbl, Russell Occhipinti

Mechanical Engineering

This project was created with the intent of automatically composting equine bio waste to be reused as plant fertilizer. The system consists of four subsystems: power generation and storage, automatic controls, aeration, and structure. Each subsystem may be manufactured independently, then put together. This system will not have access to power outlets, so it was designed to be solar-powered.

Treadmill Platform For Quadrupedal Robots, Baxter J. Bartlett, Jack F. Butler, Phillip A. Shafik, Tarun S. Ganamur

Mechanical Engineering

Cal Poly Legged Robots, led by Professor Refvem and Professor Xing, has been leading Cal Poly’s attempts to simulate, produce, and test their legged robots. The initial testing of the locomotion of these robots can be dangerous to the robot since any bugs in the code could cause the robot to fall over and harm itself. Our responsibility as a team was to deliver a portable platform for testing the locomotion capabilities containing a fall prevention mechanism. In short, we have designed a platform for this purpose that consists of a treadmill surrounded by a wheeled chassis with a system …

Planar Element Alignment System, Benjamin E. Lavigna, Benny F. Cruz, Samuel Gierhan, Jacob Q. Henriksen

Mechanical Engineering

Precise alignment to the micron level is a necessity for microfluidic/micromechanical devices to function as designed. Because of this, a micro-alignment device was commissioned by Professor Hans Mayer on behalf of the Cal Poly Microfluidics Laboratory. Prototype creation was bounded by a set of requirements including, ability to align PDMS & Silicon wafer halves to ± 10 microns, total process speed of three minutes, and total budget of $3000. Some major design hurdles included an ability to verify alignment, possible non-planar alignment pieces, and an inability to contact any point on the face of the alignment pieces after bonding treatment. …

Northrop Grumman Collaboration Project, Nikkia Rae Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake

Mechanical Engineering

The Northrop Grumman Collaboration Project (NGCP) is a collaborative club project sponsored by Northrop Grumman for the students of Cal Poly San Luis Obispo (CPSLO) and Cal Poly Pomona (CPP) to create a fleet of vehicles to aid in the simulated rescue of stranded hiker. The CPSLO club is responsible for delivering an autonomous flight vehicle that can suppress a fire and retrieve a payload. Mechanical Design Team of the CPSLO team was responsible for the design of the frame, electronics housing, and payload and fire suppression systems.

Tree Climbing Limb Saw, Andrew E. Bray, Parker Tenney, Drew M. Robles, Aimee T. Chiem

Mechanical Engineering

This document is the comprehensive report for the Tree Climbing Limb Saw Senior Project. The purpose of the Tree Climbing Limb Saw project, completed by mechanical engineers Andrew Bray, Aimee Chiem, Drew Robles, and Parker Tenney, is to remove low-hanging branches (<15 >ft) to prevent forest fires from travelling up into the canopy, where wind can carry embers for miles. An RC car was heavily modified to create a solution for this problem. A chainsaw was also mounted to deal with the cutting part of the problem. Creating a project which aims to solve this problem is a great step …

Novelty Ice Cream Assembly Prototype, Mason Sylvester, Logan Williamson, Alvaro Martinez, Adin Gilman-Cohen

Mechanical Engineering

Cool Beans USA is a novelty ice cream startup company founded by Keith Zachow. In the winter of 2022, our team began working with Mr. Zachow to develop a machine to automate parts of the production process for his product. This product consists of two hemispherical ice-cream cone shell halves filled with soft serve ice cream and pressed together. The assembled pods are around the size and shape of a small walnut and are intended to be sold in stores as a frozen finger food. At the time of project inception, this product was in its early stages and was …

Rotating Backing Brush, Caleb Savard, David Dalal, Max Allred, Mathis Weyrich

Mechanical Engineering

In the final steps of GAF’s shingle production process, small asphalt particles called fines are applied. Some fines adhere well to the shingle sheet, while others temporarily stick only to fall off the sheet further down the manufacturing line. As a result, the shingle plant floor is covered in fines that have fallen due to vibrations and gravity. The technicians and engineers at GAF want a cleaner working environment and to potentially reuse the loose fines. We are a senior project team that solved this problem by designing a system to remove and collect loose fines. In this document, the …

8 Dof Quadrupedal Hopping Robot, Clayton T. Elwell, John Bennett, Tyler Mccue, Daniel Munic

Mechanical Engineering

The goal of our senior project was to fabricate an eight degree of freedom (DOF) prototypical quadrupedal robot, develop a controller than commands the quadruped to repeatedly jump 10 cm in the air, and fabricate a modular test stand to safely deploy our controller on the quadruped. The creation of a functional quadruped will bring attention to Dr. Siyuan Xing and Charlie Refvem’s research group, Cal Poly Legged Robots, and will give future Cal Poly undergraduate and graduate students a learning tool to explore dynamic control of biomimetic robotic systems.

Over the course of our senior project, we successfully manufactured …

Interactive Lego Girl Scout Arm, Christopher Suzuki, Emi Okuyama, Bryson Shores, Karina Sandoval

Mechanical Engineering

This Senior Project Report document outlines the senior design project for Girl Scouts of California’s Central Coast (GSCCC) led by a team of four Mechanical Engineering students at California Polytechnic State University, San Luis Obispo. The project encompasses the researching, designing, prototyping, and testing of a LEGO robotic arm for the Girl Scouts to learn more about STEM (Science, Technology, Engineering, and Mathematics) and provide support to each Girl Scouts cookie sales in their stores. Their goal was to build a LEGO robotic arm that will interact with customers at the Girl Scout stores and promote the girl scouts' interest …

Mtb Daq - Mountain Bike Data Acquisition System, Theodore J. Philliber, Ronan M. Shaffer, Dylan M. Ruiz, John M. Ringrose

Mechanical Engineering

Mountain bike suspensions systems are set up and tuned based only on qualitative, ‘feeling’-based metrics. The MTB DAQ, sponsored by Dr. Joseph Mello with the Cal Poly Mechanical Engineering Department, is a data acquisition system we developed to improve suspension tuning with a data-driven approach. The system mounts to a bicycle frame and has sensors that measure vibration and travel speed to characterize the bike’s motion. While similar systems exist, they cost in the thousands of dollars range and are very specific to individual bike geometry. Our system was designed to be more affordable to the average rider as well …