Electro-Mechanical Systems Commons^™

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

A Case Study On Optimizing Industrial Air Conditioning With Thermal Solar Energy In Egypt, Tamer Adel Mohamed, Hesham Safwat, Mohammed A. Ebaid

Mechanical Engineering

This study investigates the feasibility of implementing a solar-assisted adsorption chiller in an industrial building at the Oriental Weavers International factory located in 10th of Ramadan City, Cairo, Egypt. The objective is to replace an inefficient split air conditioning system currently used to cool the Jacquard units during carpet manufacturing. The research begins by analyzing the performance of the existing cooling system to establish a baseline. It then explores the potential energy savings achievable by replacing the current system with a solar-assisted adsorption chiller. The existing oversized boiler will serve as an auxiliary heater for the new system. TRNSYS simulation …

Rapid Composter, Cate Seay, Clarisbet De Jesus, Lesley Milena Estrada, Reese Dennett

Mechanical Engineering

This Final Design Review documents the efforts of a team of mechanical engineering students from California Polytechnic State University, San Luis Obispo as they work towards completing their assigned senior design project. This team was tasked with designing and developing an onsite rapid composter for the Girl Scouts of California’s Central Coast. The selected design concept that will be explained focuses on creating a composter that is child-safe, portable, weatherproof, solar-powered, and requires minimal manual user input. This report will not only provide a detailed description of the chosen design but will also supply an extensive design justification. This mainly …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Development Of A Modular Solar Shingle, David Dye, Andrew Schmidt, Mitchell Cozzens

Williams Honors College, Honors Research Projects

The goal of this research project is to design, prototype, and test an array of solar roofing shingles using print-in-place principles using an automated circuitry printer and 3D printed components. The shingle shall emphasize ease of installation, maintenance, and affordability in contrast to the current market for solar roofing. The design goal is to develop a manufacturing process to be more cost and time effective than current manufacturing techniques. The prototype will consist of a roof with this system, demonstrating the durability, assembly, and ease of installation. Finally, material/design suitability will be implemented in conjunction with postprocessing techniques to create …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Aeroponic System Optimization For Butterhead Lettuce Growth And Future Sustainability Using Flow Blurring Atomization, Taylor J. Johnson

Doctoral Dissertations and Master's Theses

The global population has grown by 6 billion people over the last century and is trending toward 9.7 billion people by the year 2050. Agriculture accounts for 70% of global fresh water usage. Technology must be developed to accommodate the increase of food production demanded by the growing global population and the subsequent increase in water usage. Aeroponic technology is a water-efficient vertical farming technology that can reduce water usage by 90% by suspending plant roots in air within a controlled chamber and supplying atomized droplets of a water-nutrient solution directly to the roots.

This study simultaneously tests six droplet …

Power Thyristor Controller For Speed Control Of Dc Motor, Alejandra Zapata, Morgan Erich Boehme, Abdullah Mohammed Awidah, Payton Robert Chalstrom

Electrical Engineering

In this work, a Power Thyristor Controller for Speed Control of DC Motor has been developed with the purpose of replacing an existing simulation experiment, aiming to effectively implement the principle of learning by doing. The primary objective of the experiment setup is to illustrate the fundamental principles and operational mechanisms underlying the firing angle and controlled bridge rectifier. The new experiment is taking advantage of the existing FCRO4100 Single Phase Firing Board that was donated to the University by ENERPRO. The pre-programmed microcontroller is connected to the thyristor bridge rectifier that’s powered by 24VAC. Additionally, a DC motor will …

Rapid Composter, Shannon Shinozaki, Avin Atencio, Jonathan Fraser, Lukas Kolbl, Russell Occhipinti

Mechanical Engineering

This project was created with the intent of automatically composting equine bio waste to be reused as plant fertilizer. The system consists of four subsystems: power generation and storage, automatic controls, aeration, and structure. Each subsystem may be manufactured independently, then put together. This system will not have access to power outlets, so it was designed to be solar-powered.

Experimental And Theoretical Analysis Of Nonlinear Triboelectric Energy Harvester For Frequency Up-Conversion Applications, Hadeel A. Abumarar

Mechanical Engineering Theses

With the development of micro-sensors and wireless applications, energy harvesting has become an effective method for self-powering. However, ambient energy is only limited to below 100Hz, which restricts the energy harvester designs to this range resulting in
an impractical bulky and large-scale harvester. Therefore, in this thesis, we investigated
frequency Up and Down conversion energy harvesters to benefit from the high-frequency oscillations and transferred them to the ambient vibration ranges. Toward this, the triboelectric transduction mechanism has been utilized for a frequency-up conversion for energy harvesting applications, while the piezoelectric transduction mechanism is used for frequency-down
conversion for mass sensing …

Mechanical Energy Harvester For Powering Rfid Systems Components: Modeling, Analysis, Optimization And Design, Alireza Babaei

Theses and Dissertations--Mechanical and Aerospace Engineering

Finding alternative power sources has been an important topic of study worldwide. It is vital to find substitutes for finite fossil fuels. Such substitutes may be termed renewable energy sources and infinite supplies. Such limitless sources are derived from ambient energy like wind energy, solar energy, sea waves energy; on the other hand, smart cities megaprojects have been receiving enormous amounts of funding to transition our lives into smart lives. Smart cities heavily rely on smart devices and electronics, which utilize small amounts of energy to run. Using batteries as the power source for such smart devices imposes environmental and …

Machine Learning Approach For Classifying Power Outage In Secondary Electric Distribution Network, Stephan Mgaya, Hellen Maziku

Tanzania Journal of Engineering and Technology (TJET)

Power outage is the problem that hinders social and economic development especially for developing countries like Tanzania. Frequent power outages damage electric equipment, and negatively affect the industrial production process. Power outages cannot be completely eradicated due to uncontrolled cause like natural calamities but technical challenges can be managed and hence reducing power outages. The existing manual methods used to locate power outage like customer calls is inefficient and time consuming. On the other hand, modern method like the Advanced Metering Infrastructure (AMI) still faces a challenge in effectively classifying power line outage due to the nature of imbalanced datasets. …

Assessment Of Energy Efficiency In Beverage Industry, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

The brewery industry has a significant contribution to the national income. However, it is also associated with energy intensive processes and pollution. In this work, the energy efficiency assessment of the largest brewery in Tanzania i.e., Tanzania Breweries Limited has been conducted. Energy consumption analysis was conducted according to IEEE SA 739 1995. Important parameters used to assess brewery energy efficiency were boiler efficiency and losses, equipment energy productivity as well as load factor. It was found that the main energy consumers are packaging (54.63%), brewing (29.30%) and utilities (15.17%). More importantly, it was found that about 68% of the …

An Experimental Approach Towards Pv-Based Solar System Sizing For An Engineering Laboratory, Muyideen O. Lawal

Tanzania Journal of Engineering and Technology (TJET)

This study aims at providing an experimental sizing procedure for a rooftop PV-based solar power system for an engineering laboratory. This was achieved by monitoring the peak power and energy delivered by an installed 20W solar panel into an 18 Ah battery. Knowledge of the average daily peak power and energy was used to determine the percentage rated capacity available for use and the sun hour. A load consumption comparison was also carried out with and without the connection of a load to inverter. In addition to this, the monitoring of the no-load consumption of the inverter was carried out. …

Baker/Koob Final Report: Solar Solution For Mini Mars Rover, Jonathan Cederquist, Cole Korchek, Derick Louie, Michaella Ochotorena, Collin Petersen

Mechanical Engineering

This project focused on designing, building, and testing a functional prototype of a collapsible solar array on the mini Mars rover being developed by client and sponsor, Mr. Rich Murray. Although many previous collapsible solar arrays have been deployed for space missions, the previous solar-powered Mars rovers only deployed their arrays once upon landing. This solar array will be able to collapse and deploy multiple times to allow for greater rover mobility and stability when the rover is not charging. This system is critical to the success of the rover project because it provides power without which the rover cannot …

Cal Poly Fluid Power Vehicle Challenge 2022, Sangmin Sung, Eddy Rodriguez, Travis Welch, Jeremy Baechler, Kevin Pauls

Mechanical Engineering

In this report, the Featherweight Cycles design team puts forth the scope and overview of their design project, discusses background research and competitor analysis, and presents the project’s final design and manufacturing plans. The overall goal of this project is to fabricate and compete in the Fluid Power Vehicle Challenge, hosted by the National Fluid Power Association. To better define the design process, the team researched previous year’s designs from Cal Poly, as well as winning designs from the last two years to form a baseline of knowledge about competing schools’ designs. After researching multiple design paths, Featherweight Cycles chose …

Zero-Power Ac Current Sensor, Omar Aragonez

Mechanical Engineering ETDs

In this study, a magnetic piezoelectric cantilever powered AC current and frequency sensor is proposed. This paper covers the configuration of the experimental setup, finite element modeling of the magnetic coupling, and the optimal spatial location of the magnetic proof mass in relation to the wire for smart grid applications. Solid and stranded copper wires of various gauges were used and carried current up to 30A. The magnets act as a proof mass to lower the frequency while also coupling to the magnetic field generated by the current carrying wire. The frequency of the AC current produces a sinusoidal force …

Energy Analysis Of Heating, Ventilation, And Air Conditioning Systems, Erica Ferguson

Williams Honors College, Honors Research Projects

This project studied Heating, Ventilation, and Air Conditioning (HVAC) systems for commercial buildings. I completed an energy model Raleigh County Sheriff’s Department in West Virginia. This building’s HVAC has been completed by the consulting engineering firm: Scheeser Buckley Mayfield. I intern at this company, so they allowed me to use their original design as a basis for comparison. Load calculations, utility costs, energy consumption, and carbon footprint were derived from this energy analysis. The energy model compared three systems: variable air volume (VAV) with electric reheat, variable air volume with hydronic reheat, and variable refrigerant volume (VRV). Based on the …

The Capabilities And Limitations Of Flywheel-Based Energy Storage System Pertaining To Subways In The Event Of A Power Outage, Jaskaran Singh

Dissertations and Theses

In the city that never sleeps, power outages or blackouts can be a shock, especially if you are on a train amid one. For example, during the infamous 2003 blackout, thousands of people were left stuck and stranded in parts of Northeastern United States. In particular, with no trains or buses in service throughout the 5 boroughs of NYC, those stranded essentially had no way to go back home. Hotels, terminals, and airports alike became places of camping as the city seemed to come to a halt. For the sake of public safety and transit efficiency, this study explores a …

Nonmetallic Jet Impingement Thermal Management For Power Electronics Via Additive Manufacturing, Reece Whitt

Graduate Theses and Dissertations

The increase in energy demanded by transportation and energy sectors has necessitated highly efficient thermal management for reliable power electronics operations. Conventional cooling techniques are limited by their inability to target switching location hot spot temperatures, leading to non-uniform thermal gradients. These devices, such as cold plates and heat sinks, also utilize heavy metallic structures that can accentuate electromagnetic interferences generated by high voltage switching processes. This work proposes a non-metallic jet impingement cooler for more customized thermal management, while simultaneously reducing the harmful effects of electromagnetic interferences. Additive manufacturing is utilized to enable jet impingement zones to target individual …

Hobby Grade Lithium-Ion Batteries For Spacecraft Applications: Establishing An Automated Electrical Characteristics Testing Procedure For Flight Acceptance Of Non-Space-Grade Small Secondary Batteries, Braidon Hughes

Graduate Theses and Dissertations

Li-ion batteries are widely used due to the large amount of rechargeable energy they pack into a small, light package. This higher energy density makes Li-ion batteries ideal for small satellite applications, specifically CubeSats. CubeSats have grown in popularity in higher level education due to the National Aeronautics and Space Administration’s implementation of the Cube Satellite Launch Initiative, making it easier and cheaper to conduct small, low orbit missions. Because these CubeSats are occupying the same space as a crewed spacecraft, it is imperative that they are safe. There are numerous reports of Li-ion batteries creating fires that result in …

Assessment Of The Impacts Of Climate Variability On Hydropower Generation: A Case Study Of The New Pangani Falls, Tanzania, Dativa Byarufu

Tanzania Journal of Engineering and Technology (TJET)

Climate change poses potential impacts on hydropower generation either positively by increasing or negatively by decreasing river flow. This study assessed the impacts of climate variability on hydropower with a focus on the New Pangani Falls in Tanzania. Rainfall and temperature time series data from 1980-2014 were analyzed in relation to river discharge and associated impacts to hydropower generation. The Man-Kendall test was used to detect trend in both annual and seasonal time series. The results showed a negative trend in annual rainfall with Z= -2.41 at α = 0.05 and the slope Q = -0.964. Seasonal trend analysis showed …

Development Of Novel Battery Materials For Lithium-Ion Batteries And Beyond, Jiyu Cai

Graduate Theses and Dissertations

As fossil fuels are depleting and causing environmental issues, it becomes imperative to widely implement renewable energies (e.g., solar and wind power). In this context, electrical energy storage (EES) systems are essential to accommodate the intermittent supply and uneven distribution of renewable energies. To this end, high-energy-density EES devices are highly demanded, such as rechargeable batteries. This dissertation presents my efforts in developing novel battery materials for lithium-ion batteries (LIBs), sodium-ion batteries (SIBs), and solidstate lithium batteries (SSLBs). These efforts include electrochemical evaluations of battery materials, surface modifications of electrodes via atomic layer deposition (ALD), and advanced characterizations of batteries …

High Temperature Degradation In Gan-Based Hall Effect Sensors, Alexis Anne Krone

Graduate Theses and Dissertations

This research focuses on understanding the effects of accelerated aging through temperature and environment on novel gallium nitride-based Hall effect magnetic field sensors and determining device reliability under electric vehicle operating conditions. The device reliability was modeled using accelerated aging for the temperatures of 200 °C, 350 °C, 450 °C, and 600 °C under various time steps unique to each temperature and either air, which is identical to operating circumstances, or argon, which would model the hermetic packaging environment. Using a high temperature furnace and oven, devices underwent high temperature storage tests at a chosen temperature and time step. Afterwards, …

Consumer-Ready Insulated Solar Electric Cooker, Simon Ford, Sachin Gokhale, Brendan Lynn, Richard Nguyen

Mechanical Engineering

An insulated solar electric cooker, or ISEC, converts solar energy into electricity to cook food, boil water, provide heat or even help charge batteries. In this project, the focus is an ISEC with a phase change material (PCM) that helps store heat when the solar energy input is minimal, such as after the sun has set. Although a successful ISEC already exists that utilizes PCM, this product can be improved in many ways. The specific revisions investigated in this report are the improvement of the thermal efficiency with the implementation of a vacuum-sealed outer pot, the reduction of the overall …

Nanoscratch Study Of Diamond-Like Carbon Coatings With A Polydopamine + Sio2 Adhesive Underlayer, Anna Fisher

Mechanical Engineering Undergraduate Honors Theses

Diamond-like carbon (DLC) coatings have a wide array of desirable characteristics such as low friction, high hardness, and scratch resistance. Due to high residual stress and thermal mismatch, DLC films experience adhesion difficulties when bonded with metallic substrates, leading to cracking and delamination. In this study, the properties of a new coating with a polydopamine underlayer and silica nanoparticles bonded to a stainless-steel substrate (PDA+SiO2/DLC) were studied alongside three other samples, one with a polydopamine underlayer (PDA/DLC), one with a trimethylsilane (TMS) underlayer (TMS/DLC), and one with no underlayer (DLC only). Nanoscratch tests were performed with a 1 μm spheroconical …

Computational Study On Suppression Of Airfoil Flow Separation Using High-Frequency Translational Surface Actuation, Bibek Gupta

Honors Theses

Flow separation is a phenomenon that occurs when pressure increases in the streamwise direction of a flow, making a distinctive boundary layer or separation bubble. It causes aircraft to experience an increase in drag and noise and a decrease in a lift, hence degrading their aviation performance. This study uses numerical simulations to understand better the effects of high-frequency translational surface actuation (HFTSA) on flow separation control. The numerical simulations mimic the experimental parameters of an experiment performed by Okoye et al. on using the HFTSA system to control flow separation. A symmetrical airfoil structure of chord length of 0.3 …