Electro-Mechanical Systems Commons^™

Power At Sea Develop Phase, Jake Lauer, Isabella Heinemann, Bailey Gargasz, Zachery Boyer

Mechanical Engineering

This project develops a renewable, wave-powered charging system designed to extend the mission duration of Autonomous Underwater Vehicles by eliminating the need for frequent manual battery replacement. Building upon a prior oscillating water column prototype from the CONCEPT phase, the team redesigned and tested an improved system capable of converting wave-induced air motion into electrical power using a Wells turbine. Key enhancements include doubling the column diameter to increase displaced air volume, integrating a flared inlet and bi-directional nozzle to improve airflow, and selecting corrosion-resistant materials suitable for long-term deployment in marine environments. Multiple prototypes were constructed and evaluated through …

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Off-Grid Cabin Hydroelectric Generator, Keller Feltman, Lance Savatgy, River Perino, Jesse Valencia

Mechanical Engineering

This project developed a portable hydroelectric generator intended to provide low-power electricity generation for an off-grid cabin in Alpine County, California. The system was designed to utilize naturally occurring creek flow to generate electrical power while remaining portable, durable, and environmentally conscious.

The final system consists of an axial-flow turbine, belt-driven generator subsystem, waterproof electronics enclosure, aluminum support frame, and integrated wildlife protection screening. Engineering analysis was performed to estimate hydraulic power availability, turbine performance, drivetrain requirements, and component lifespan. These analyses guided the selection and development of the final design.

Throughout prototype testing, several design modifications were required. Initial …

Water Turbine Dynamometer For Low-Power Turbomachinery Testing, Carmen Alaichamy, Yosef Huynh Torres, Michael Duperly, Michael Thomas Duff

Mechanical Engineering

Students in ME 443: Introduction to Turbomachinery compete to design and build efficient small impulse turbines. The course lacks a standardized method to experimentally calculate turbine power output and mechanical efficiency from accurate measurements of torque and speed, for example. To support the learning goals of ME 443, a dedicated water-turbine dynamometer is needed to provide controlled hydraulic power, accurate mechanical and electrical measurements, and clear data for performance evaluation.

Our proposed system delivers a safe, repeatable, and educational testing environment that can be integrated into the Fluids Lab or used as a standalone instructional tool. Key stakeholders include Professor …

A Review Of Energy Storage Technologies With Hydro Energy System Design For Off-Grid Electricity, Daniel H. Ngoma, Banet L. Masenga

Tanzania Journal of Engineering and Technology (TJET)

Many renewable energy sources such hydropower—particularly small-scale run-of-river and micro-hydro—offers reliable, low-cost generation. However, their inherent intermittency (due to seasonal flow variations) and inability to instantly match demand necessitate integrated energy storage to ensure a stable, continuous power supply. This review synthesizes contemporary energy storage technologies in the context of their integration with off-grid hydro energy system design.

The study examine a spectrum of storage solutions, evaluating their technical characteristics, costs, and suitability for hybrid hydro applications. Pumped Hydro Storage (PHS), while highly efficient and large-scale, is often geographically constrained and capital-intensive for small off-grid projects. Battery Energy Storage Systems …

Deep Learning Based Control System For Multi-Zone Hvac Residential Buildings, Mohammad H. Z. Alghalayeeni

Mechanical Engineering Theses

Heating, ventilation, and air conditioning (HVAC) systems are major contributors to residential energy consumption. However, most homes continue to rely on single zone thermostat control, which regulates temperature based on a single sensor and cannot account for thermal variations across multiple rooms. This often leads to uneven thermal conditions and inefficient energy use in multi-zone residential buildings. This thesis presents a deep reinforcement learning based approach for improving HVAC zoning control through dynamic airflow distribution. A physics based multi zone thermal model of a residential house was developed to simulate heat transfer processes including conduction, convection, solar and internal heat …

Areosense, Josephine Turney

Williams Honors College, Honors Research Projects

The AeroSense growing system is designed to make indoor aeroponic gardening easy and accessible for everyone. By combining sensors, automation, and AI, the system can monitor and adjust humidity, lighting, and nutrient levels to help plants thrive without requiring expert knowledge. The goal is to create a self-regulating garden that takes the guesswork out of growing fresh herbs and vegetables at home. The project involves building a working aeroponic prototype equipped with misters, pumps, and environmental sensors, all managed by a Raspberry Pi. Using computer vision and machine learning, AeroSense will be able to assess plant health and respond automatically …

Simulation And Characterization Of Fuel Cell System Incorporated Internet Of Things, Ahmad N. Alhjouj

Mechanical Engineering Theses

Small air-cooled proton exchange membrane fuel cell (PEMFC) systems are increasingly relevant for portable and distributed applications, yet practical modeling and monitoring methods remain limited: high-fidelity physics-based models are too costly for real-time use, while purely data-driven models discard physical interpretability. This thesis develops an experimentally grounded gray-box framework for the characterization, reduced-order modeling, and IoT-enabled monitoring of a small hydrogen PEMFC system. A low-order nonlinear state-space model couples an electrochemical voltage layer to a lumped thermal layer, with parameters identified in stages using self-adaptive differential evolution. Identifiability analysis shows that static loss parameters are well constrained, while dynamic parameters …

Analytical And Data-Driven Modeling And Control Of Nonlinear Point Absorber Wave Energy Converters With Application To Cone–Cone Buoy Geometries, Houssein Yassin

Dissertations, Master's Theses and Master's Reports

This dissertation develops analytical modeling, numerical simulation, experimental validation, and data driven control methods for nonlinear point absorber wave energy converters, with particular emphasis on cone--cone buoy geometries. Geometry dependent nonlinear force models are first derived using pressure field and displaced volume formulations. These models show how buoy geometry produces nonlinear Froude--Krylov and restoring forces, including the dominant cubic behavior of cone--cone geometries.

The derived models are incorporated into a feedback linearization framework that compensates selected nonlinear dynamics while retaining the incident wave terms. An analytical optimal control formulation is also developed to maximize harvested energy in nonlinear, nonautonomous systems …

Machine Learning And Multi-Scale Optimization For Control And Energy Management In Connected And Automated Vehicle Propulsion Systems, Joshua D. Orlando

Dissertations, Master's Theses and Master's Reports

This dissertation presents a multi-scale optimization framework leveraging machine learning (ML) to enhance energy efficiency in connected and automated vehicle (CAV) propulsion systems. As transportation transitions toward hybridization and automation, the integration of vehicle-to-everything (V2X) connectivity and advanced control algorithms offers unprecedented opportunities for energy reduction. This research addresses three critical scales of vehicle energy management: multiple vehicle-level coordination, component-level powertrain dynamics, and real-time vehicle parameter estimation.

First, the research investigates the energy consumption characteristics of heterogeneous propulsion systems—ranging from internal combustion engines to battery electric vehicles across light- and heavy-duty sectors—on arterial roadways. Utilizing Particle Swarm Optimization (PSO) and …

Opposed-Piston Two Stroke Engine As A High Power Density Solution In Heavy Duty Applications: An Experimental Evaluation With Diesel And Ethanol, Ankur Bhatt

All Dissertations

With an increasing demand to reduce greenhouse gas (GHG) emissions, the conventional powertrain technology is at a saturation point. There is reinvigorated research interest in alternative powertrain designs that offer potentially higher efficiencies and lower engine-out emissions compared to conventional powertrains. The opposed piston two-stroke (OP2S) engine is one such alternative engine architecture that has demonstrated a reduction in engine-out emissions and increased efficiency compared to conventional four-stroke diesel engines. Like any two-stroke engine, the scavenging process and the composition of the internal residuals are predominantly governed by the pressure differential between the intake and the exhaust ports. Without dedicated …

Control Of Ferroelectric And Dielectric Properties Of Undoped, Fe, And Nb-Doped Single-Crystalline (001) Oriented Pb (Zr0.5ti0.5) O3 Thin Films, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

While several factors that influence the properties of ferroelectric devices have been extensively studied in bulk ceramics and polycrystalline thin films, limited is known about the same on single crystalline thin films which have great potential in memory and energy applications. This knowledge gap is largely due to the limited availability of substrates with lattice parameters suitable for supporting high-quality epitaxial growth. In this study, undoped, Fe-doped, and Nb-doped (001)-oriented Pb(Zr₀.₅Ti₀.₅)O₃ thin films were deposited using pulsed laser deposition, each with a SrRuO₃ bottom electrode and a PrScO₃ substrate. The doping concentration used is 1% for both Fe and Nb. …

Design Of A 10-Ton Capacity Solar-Powered Cold Storage At The Cituis Fish Auction Site, Tangerang, Banten, Indonesia, Wardi Wardi, Muhammad Arif Budiyanto

Journal of Materials Exploration and Findings

This study presents the design of a 10-ton capacity solar-powered cold storage system for the Cituis Fish Auction Site (TPI) in Tangerang, Indonesia, as a sustainable solution to support the coastal fisheries sector. The system comprises two temperature zones: an anteroom at 5°C and a freezer room at -30°C, both integrated with a hybrid system utilizing solar panels and batteries. The total power consumption of the cooling system reaches 27.51 kW. The simulation results, obtained using HOMER Pro software, indicate that the hybrid PV system can reduce CO₂ emissions by up to 16,754 kg per year. From an economic …

Mitigation Of Voltage Disturbances In Industrial Power Distribution Networks Using Dynamic Voltage Restorers, Aviti T. Mushi

Tanzania Journal of Engineering and Technology (TJET)

Most electrical and electronic equipment in industries require high-quality power to function efficiently. Nonetheless, voltage sags and swells are pressing concerns and prone to directly impact the economy of industrial customers. One such customer embattled with these problems is Mbeya Cement Company Limited (MCC) located in Mbeya, Tanzania. These issues mainly are caused by upstream faults and switching operations. One way to address these is by utilizing the voltage injection method, which employs a power device known as a dynamic voltage restorer (DVR). In this paper, the voltage sags and swells of balanced three-phase, unbalanced double-line and single-line to ground …

Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

The demonstration of a typical hydropower plant requires the development of a test rig with the installation of tools to measure the performance parameters. The measurement tools require a calibration process to improve the quality of recorded data. This study involved the calibration of traditional and automated measurement tools connected to the hydropower test rig through an Arduino microprocessor. The automated measurement tools included a pressure transducer, flow meter, digital tachometer, and torque transducer, while traditional measurement tools, including a pressure gauge, concrete water tank, contact tachometer, and force lever arm balance, were connected in the same test rig during …

Review On Gas-To-Liquids Conversion Technology: Lessons From Case Studies And Potential Strategies For Implementation In Tanzania, Joseph H. Kihedu

Tanzania Journal of Engineering and Technology (TJET)

This review paper explores the transformative potential of Gas-to- Liquids (GTL) technology for harnessing Tanzania's vast natural gas resources. With significant discoveries of natural gas reserves totalling up to 57 Tcf in fields such as Songosongo, Mnazi Bay, Block 1, 2, 3 and 4. Tanzania is positioned to leverage GTL technology to convert these resources into high-value liquid fuels like gasoline, diesel and naphtha. Review of GTL process, its products and applications has been done. By analysing successful GTL projects globally and drawing lessons applicable to Tanzania, this paper provides strategic recommendations for policymakers and stakeholders to foster GTL development. …

A Review Of Lithium-Ion Battery Capacity Fade Deceleration At Power Fluctuations In Renewable Energy Systems, Isaac Gwayi

Tanzania Journal of Engineering and Technology (TJET)

Application of lithium-ion (Li-ion) batteries to store energy in renewable energy systems (RESs) is increasing due to their promising properties. Therefore, it is crucial to understand aging behaviours of Li-ion battery during RES life time as this directly affects cost of energy. Li-ion battery aging can be categorised into calendar aging and cycle aging. Calendar aging depends mainly on temperature and state of charge (SoC). In addition to temperature and SoC, cycle aging depends also on charge and discharge current rates and cut-off voltages. Higher current rates lead to faster Li-ion battery aging. It is necessary to identify appropriate battery …

Assessment Of Maintenance Performance Level Of Selected Hydropower Plants In Tanzania, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

Despite significant progress in increasing electricity access to over 78%, electricity reliability in Tanzania remains a concern, with frequent power outages reported. Maintenance issues in hydropower plants have been identified as a critical factor contributing to this problem. However, the specific maintenance performance levels have not been fully assessed. This study conducts a comprehensive evaluation of the maintenance performance of four key hydropower plants: Kidatu (204 MW), Kihansi (180 MW), Mtera (80 MW), and New Pangani Falls (68 MW). Data collected from staff surveys and maintenance records between 2018 and 2022 were used in the study. Although staff demonstrated a …

Root Cause Analysis Of Performance Degradation For An Xyz Thermal Power Plant In Tanzania, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Thermal power plants in Tanzania have been experiencing performance degradation, typically arising from component and subsystem failures, which contribute to power system instability and unreliability. This paper presents a case study of the root causes of performance degradation of an XYZ thermal power plant. The study was conducted by reviewing plant documentations, including maintenance and operational data logbooks, and by standardising the approach through the adoption of ISO 14224:2016 for maintenance and reliability data exchange. Data evaluation was carried out using principal component analysis and scree plot analytical techniques to enhance the depth and accuracy of root cause identification. Additionally, …

Potential Use Of Pump As Turbine Coupled To Self-Excited Induction Generator For Micro-Hydro Cooking And Cooling Applications, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

Clean cooking and efficient cooling in developing countries have recently become areas of great focus. Further, the environmental impact of flooding in high-capacity hydroelectric plants has become a major concern. As a result, there is growing emphasis on developing sustainable and decentralized energy solutions, focusing on the potential of micro-hydro systems, especially in rural and remote areas. Although there are several alternative energy generation methods, their application is not straightforward. One of the latest technologies under research is using pumps as turbines coupled to an induction generator. This paper explores through a rigorous experimental approach the possibility of using a …

Optimal Placement Of Distributed Generation Units In Power Distribution Networks Using Particle Swarm Optimization, Owdean M. Suwi

Tanzania Journal of Engineering and Technology (TJET)

Power losses and voltage drops in distribution networks are critical issues in power system operation, reducing efficiency, reliability, and overall quality of the power supply to customers. Additionally, the rising electricity demand, deregulation of energy markets, and congestion in transmission networks have further contributed to the declining performance of the grid. To address these challenges, integrating distributed generation units (DGUs) into electric distribution systems has gained significant attention. Furthermore, the integration of DGUs into conventional fossil fuel-based power plants is becoming necessary to reduce greenhouse gas emissions. However, proper placement and sizing of DGUs are crucial for achieving optimal benefits. …

Hydropower Collegiate Competition, Aiden D. Foster, Devon Bountry, Joanna Vo, Timothy Rinker, Amanda Rodriguez, Minh Nguyen, Eli Haushalter, Sophie Watkinson, Maiya Holton, Breanne Evans

Mechanical Engineering

The Cal Poly SLO HCC team presents a feasibility study and engineering design review package for retrofitting the non-powered Ritschard Dam in Colorado into a hydroelectric facility as part of the 2025 Hydropower Collegiate Competition. Through a rigorous and multi-staged assessment of plausible dam sites in the western US, the team has chosen the Ritschard Dam in Colorado to implement an electromechanical component designed to accommodate a large range of flowrates stemming from a large variance in upper reservoir capacity due to geographical and climate effects. The team evaluated non-powered dams based on technical feasibility, electric grid proximity, power generation …

Computational Modeling Of Torque Arm And Load Cell Interactions In Uta Racing Brake Dynamometer, Anthony A. Aiyedun

2025 Spring Honors Capstone Projects - Archive

The UTA Racing Team is developing a brake dynamometer to measure the coefficients of friction of various brake pads and calipers under controlled conditions. The dynamometer simulates on-track braking scenarios, testing brake pads at temperatures up to 1300ºF and pressures similar to racing environments. Its primary goal is to generate accurate friction vs. temperature graphs for various brake pad and rotor combinations, addressing the need for dedicated testing equipment. This project creates an ANSYS simulation of the torque arm and load cell interaction. The computational model accurately represents the relationship between applied torque and measured load cell force, incorporating precise …

Synthetic Inertia Provision For Load Frequency Control In Networks With High Penetration Of Renewable Energy Sources, Paulina Mkoi

Tanzania Journal of Engineering and Technology (TJET)

The integration of renewable energy sources (RESs) such as solar photovoltaic (PV) and wind energy has become a promising solution as the world shifts toward clean energy. Solar PV and wind resources are increasingly replacing conventional synchronous generators, leading to reduced system inertia and increased vulnerability to frequency instability during disturbances. To address this challenge, this study proposes a novel synthetic inertia provision strategy using a battery energy storage system (BESS) integrated alongside solar PV. The proposed method dynamically compensates for the loss of inertia by considering the variability of solar PV output due to changes in irradiance and temperature. …

Heavy Metals Pollution In Roadside Ecosystems, Lilian Matafu

Tanzania Journal of Engineering and Technology (TJET)

Heavy metals refer to metallic elements that are characterized by having a relatively high density and they are toxic or poisonous even at low concentration. They are environmental pollutant owing to toxicity and longevity in atmosphere and ability to accumulate in living things via bioaccumulation. They tend to enter in different system such as food chain. Analyses of water, soil sediment and the surrounding growing plants (Cynodon dactylon and Cyperus species) for selected heavy metals (Cd, Pb, Zn and Cu) were conducted on a roadside pond located at Boko MSB, Dar es Salaam. Pond water, soil sediments and plant samples …

A Bibliometric Analysis Of Pat-Seig Evolution As An Alternative Energy Generation Method, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

Pumps as Turbines (PATs) coupled with Self-Excited Induction Generators (SEIGs) as an alternative energy generation method have been the subject of significant research in recent years. This paper presents a bibliometric analysis of the evolution of PAT-SEIG technology as an alternative energy generation source. An analysis of a comprehensive dataset of peer-reviewed journal articles, conference proceedings, and patents related to PAT-SEIG systems, using advanced bibliometric techniques and PRISMA to identify key research themes, influential authors, the growth of the field and patterns of collaboration, and changes in research focus over time. Over a publication period of 32 years, a total …

Efficient Operation Of Direct Coupled Solar Home Pv System: A Case Of Solar Home Pv System Installed In Dodoma, Tanzania, Sarah P. Ayeng'o

Tanzania Journal of Engineering and Technology (TJET)

Direct coupled Photovoltaic (PV) system is a common topology among most of the off-grid communities in the world. This topology has less components hence resulting in low investment costs. However, it suffers much losses when battery operating voltage is far from maximum power point voltage of PV modules. This scenario can be attributed by different factors such as; variation in solar radiation, load profile and temperature. Efficient operation of these systems is required in order to reduce losses. Usually in direct coupled system, PV modules are connected in parallel with batteries through a charge controller hence making PV output to …

High Voltage Junction Box For Demonstrator Vehicle, Benjamin Lubowicki, Ryan Dorste

Williams Honors College, Honors Research Projects

Schaeffler, our industry sponsor for this project, is designing a battery pack for a demonstration vehicle that requires a high voltage junction box to route power to the vehicle. The project type is a unique design of a mechanical component, mechanism, and process. Our objective for this project is to assemble provided electro-mechanical components into an enclosure following a provided electrical diagram. The expected deliverables are the following: 3D CAD assembly of final product, FEA analysis of designed components, 2D print of final product, fabrication and assembly of designed parts, technical report documenting design process and installation. The skills required …

3d Printing Of A Solid-State Battery, Maurizio A. Brozzi

Honors Undergraduate Theses

Solid-state battery research has gained significant attention in recent years, as it provides a unique solution for several common issues in conventional Li-ion batteries. Additionally, as additive manufacturing technologies continue to advance, they have the potential to fabricate solid-state batteries with new materials. The objective of this study is to explore the feasibility of 3D printing of a solid-state battery. By creating an initial PEO-PSF hybrid polymer matrix dissolved in DMSO and adding a lithium salt, the base electrolyte ink was formed. With the addition of conductive additives and active material, electrode inks were also produced. Super P was used …

Design And Lab Implementation Of An Air Source Transcritical Co2 Heat Pump, Geoffrey Turbeville

Dissertations and Theses

A laboratory-scale air-source transcritical CO2 heat pump (TCHP) was developed to evaluate the performance of low-global-warming-potential (GWP) refrigerants for cold climate applications. A custom climate chamber was also constructed to simulate winter weather conditions typical of the northeastern United States. Both the TCHP and the chamber were fully instrumented to collect temperature, pressure, and mass flow data, which were used to calculate the co- efficient of performance (COP) in accordance with ASHRAE standard refrigerant enthalpy methods. Prior to testing the CO2 system, the experimental setup was benchmarked using a commercially available R410A heat pump manufactured by LG.

The climate chamber …