Electro-Mechanical Systems Commons^™

Mems Cantilever Sensor For Thz Photoacoustic Chemical Sensing And Spectroscopy, Nathan E. Glauvitz

Theses and Dissertations

Sensitive Microelectromechanical System (MEMS) cantilever designs were modeled, fabricated, and tested to measure the photoacoustic (PA) response of gasses to terahertz (THz) radiation. Surface and bulk micromachining technologies were employed to create the extremely sensitive devices that could detect very small changes in pressure. Fabricated devices were then tested in a custom made THz PA vacuum test chamber where the cantilever deflections caused by the photoacoustic effect were measured with a laser interferometer and iris beam clipped methods. The sensitive cantilever designs achieved a normalized noise equivalent absorption coefficient of 2.83x10^-10 cm^-1 W Hz^-1/2 using a 25 …

Mems Fabrication Process Base On Su-8 Masking Layers, Scott A. Ostrow, Ronald A. Coutu Jr.

AFIT Patents

A novel fabrication process uses a combination of negative and positive photoresists with positive tone photomasks, resulting in masking layers suitable for bulk micromachining high-aspect ratio microelectromechanical systems (MEMS) devices. This technique allows the use of positive photomasks with negative resists, opening the door to an ability to create complementary mechanical structures without the fabrication delays and costs associated with having to obtain a negative photomask. In addition, whereas an SU-8 mask would normally be left in place after processing, a technique utilizing a positive photoresist as a release layer has been developed so that the SU-8 masking material can …

Mems Lab Simulation Tool, Oluwatosin D. Adeosun, Sambit Palit, Ankit Jain, Muhammad A. Alam

The Summer Undergraduate Research Fellowship (SURF) Symposium

MEMS actuators have multiple design applications. Understanding their behavior as well as the ability to predict their actuation characteristics and voltage response is important when designing these actuators. In order to know these devices will behave, designers have to solve multiple analytical equations and experiments that can be very time consuming. Over the course of the summer a tool was created on nanoHUB that will allow users to enter information about a MEMS actuator and provide the voltage response of the actuator. To create the tool, scaling equations were first provided for various geometry configurations and the equations were next …

Metal-Assisted Etching Of Silicon Molds For Electroforming, Ralu Divan, Dan Rosenthal '14, Karim Ogando, Leonidas E. Ocola, Daniel Rosenmann, Nicolaie Moldovan

Student Publications & Research

Ordered arrays of high-aspect-ratio micro/nanostructures in semiconductors stirred a huge scientific interest due to their unique one-dimensional physical morphology and the associated electrical, mechanical, chemical, optoelectronic, and thermal properties. Metal-assisted chemical etching enables fabrication of such high aspect ratio Si nanostructures with controlled diameter, shape, length, and packing density, but suffers from structure deformation and shape inconsistency due to uncontrolled migration of noble metal structures during etching. Hereby the authors prove that a Ti adhesion layer helps in stabilizing gold structures, preventing their migration on the wafer surface while not impeding the etching. Based on this finding, the authors demonstrate …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Low Speed Alternator Design, Scott Merrick

Electrical Engineering

No abstract provided.

Micro Hydropower System, Christpher Neally, Ian Verstuyft

Electrical Engineering

The micro hydropower project strives to meet the needs of a specific village in northern Thailand in partnership with Engineers Without Borders. Specifically, the electrical side of the system must be designed to convert the mechanical power of a flowing river that is turning a turbine into sustainable and dependable power. Currently available hydropower systems will be considered, analyzed, and tailored to suit the specific needs of the community in need. The system to be designed will be flexible enough to demonstrate proof-of-concept with the limited maximum generable power in lab while having the ability to be easily scaled for …

Cal Poly Brocade Challenge 2013, Chandler Morehardt, Alexa Coburn, Juan Silva, Kerry Sun, Greg Wang, Raul Chagoya, Jd Torres

Architectural Engineering

No abstract provided.

Wind And Hydroelectric Power Simulation For The Dc House Project, Randy Lormand, Christopher Goloskie

Electrical Engineering

This project details the design and integration of a wind and hydroelectric power simulation system in correlation with the DC House Project. The simulator uses variable speed drives to rotate a DC motor which then drives a generator to produce output. This output is then regulated using a DC to DC converter which holds the voltage level constant making it easier to interface with other power sources for the house. The test results indicate that the simulator will be able to produce two separate power outputs that will provide at least 70 Watts of power in the acceptable speed range …

Swing Human Powered Generator: For The Dc House Project, Juan Vicente Avelar, Juan Jose Galindo, Juan Pramyr Ramos

Electrical Engineering

The Play Park Human Powered Generator project addresses various ways of generating power. More specifically, this project entails the design and construction of the Swing Power Generator to provide electrical power from mechanical energy. The swing generator will eventually be used as part of the human-powered generators utilized in the DC House project.

A swing generator prototype was built for this project, which demonstrates the feasibility of its use for electrical power source. Detailed design and construction of the swing generator is presented in this report along with results from hardware testing.

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Micro Modeling Study Of Cathode/Electrolyte Interfacial Stresses For Solid Oxide Fuel Cells, Xinfang Jin, Xingjian Xue

Faculty Publications

Delamination of the cathode/electrolyte interface is an important degradation phenomenon in solid oxide fuel cells (SOFCs). While the thermal stress has been widely recognized as one of the major reasons for such delamination failures, the role of chemical stress does not receive too much attention. In this paper, a micro-model is developed to study the cathode/electrolyte interfacial stresses, coupling oxygen ion transport process with structural mechanics. Results indicate that the distributions of chemical stress are very complicated at the cathode/electrolyte interface and show different patterns from those of thermal stress. The maximum principal stresses take place at the cathode/electrolyte interface …

Digitally Programmable Rf Mems Filters With Mechanically Coupled Resonators, Hengky Chandrahalim, Sunil Ashok Bhave

AFIT Patents

A digitally-tunable RF MEMS filter includes a substrate and a plurality of mechanically coupled resonators, wherein a first and a last resonator of the plurality of mechanically coupled resonators are configured to be electrostatically transduced. One or more of the plurality of mechanically coupled resonators are configured to be biased relative to the substrate such that the one or more biased resonators may be brought substantially in contact with the substrate. In a method of digitally tuning an RF MEMS filter having a mechanically coupled resonator array, a DC bias voltage is applied to at least a first resonator and …

Development Of Mems-Based Corrosion Sensor, Feng Pan

Graduate Theses and Dissertations

This research is to develop a MEMS-based corrosion sensor, which is used for monitoring uniform, galvanic corrosion occurring in infrastructures such as buildings, bridges. The corrosion sensor is made up of the composite of micro/nano metal particles with elastomers. The mechanism of corrosion sensor is based on the mass transport of corrosive species through the sensor matrix. When the metal particles in the matrix corrode, the electrical resistivity of the material increases due to increasing particle resistances or reduction of conducting pathways. The corrosion rate can be monitored by detecting the resistivity change in sensing elements. The life span of …

Computational Design Of The Electrical And Mechanical Performance Of Steerable Mems Antennas, Morgan Andrew Roddy

Graduate Theses and Dissertations

This thesis describes the origins, improvements, and variations of a broadband microwave antenna that can be beam-steered by a micro-electromechanical system (MEMS). The steerable MEMS antenna of this work was comprised of a planar antenna on top of a Silicon membrane. The membrane is etched to create a gimbal hinge structure and a platform which supported the antenna and gave it one or two degrees of freedom of rotation. The antennas presented were broadband and fed by a coplanar waveguide (CPW) transmission line which traversed the hinge structure. The antenna's orientation in space was designed to be changed through electrostatic …

Technology Portal For Energy Efficient Buildings, Larry D. Hermanson, Daniel Studer, Annie Mroz

STAR Program Research Presentations

Project: Technology Portal for Energy Efficient Buildings

Date: August 2, 2012

Author: Larry Hermanson

Mentor: Daniel Studer

Cohort: Annie Mroz

Lab site: National Renewable Energy Laboratory (NREL)

Buildings account for 71% of the electricity demand and 39% of the primary energy consumption in the United States. The Commercial Buildings Group at NREL provides builders, designers and building owners accurate information to significantly improve the energy efficiency of new and existing buildings. The Technology Portal for Energy Efficient Buildings will increase the accessibility of standardized and credible energy performance data for all building systems, thereby allowing building owners to better evaluate …

Modeling, Identification, Validation And Control Of A Hybrid Maglev Ball System, Ahmed Elhussein E. Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, the electrodynamics of a single axis hybrid electromagnetic suspension Maglev system was modeled and validated by applying it to a single axis hybrid maglev ball experiment. By exploring its linearized model, it was shown that the single axis hybrid Maglev ball has inherently unstable dynamics. Three control scenarios were explored based on the linearized model; (1) Proportional, Deferential (PD) control, (2) Proportional, Deferential, Integral (PID) and (3) PID controller with pre-filtering. This thesis has shown that a PID controller with a pre-filtering technique can stabilize such a system and provide a well-controlled response.

A parametric system identification …

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

Design, Construction, And Evaluation Of An Automated Chicken Coop Door, Kyle Inks

BioResource and Agricultural Engineering

This senior project takes a look into the design, construction, and evaluation of an automated chicken coop door. The idea and need for such a door came from my mother Jan Inks. The parameters for the project include, low production cost, easy installation on existing coops, sleek design, automatically open at a set time in the morning, and automatically close at a set time in the evening.

Polygrasp: Reach; Myoelectric Prosthetic Hand Iteration, Devon Patrick Augustus, Mighells Blaed Deuel, Ian Noel Fraser, Nicholas Philip Moesser

Mechanical Engineering

Amputations are a common occurrence in soldiers returning home who have suffered the effects of IED and munitions explosions. For upper limb amputees, trans-radial amputations are the most common. Traditional hook devices do not offer an adequate level of normalcy for users, prompting the use of myoelectric devices. While current myoelectric devices do offer a more natural experience, they come with a host of other problems that makes their adoption by service personnel not desirable or not permitted by the VA. PolyGrasp Reach seeks to reduce weight and cost and improve performance. This addresses several of the issues with devices …

A Ceramic-Anode Supported Low Temperature Solid Oxide Fuel Cell, Hanping Ding, Junjie Ge, Xingjian Xue

Faculty Publications

We report the fabrication and evaluation of a ceramic-anode supported button cell LSCM-SDC/SDC/PBSC (thickness 400 μm/20 μm/20 μm). The anode/electrolyte assembly LSCM-SDC/SDC was co-fired at low temperature of 1250°C, where a slight amount of CuO was mixed with LSCM. The CuO (20.3 wt%) were impregnated into the porous substrate to enhance current collecting effect. The cell exhibited power density of 596 mWcm−2 and 381 mWcm−2 at 700°C with wet hydrogen and methane as the fuel respectively, where the silver paste was used as current collectors, the highest performance up to date for the cells with metal oxide anodes at this …

Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer

Master's Theses

The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …

Experimental And Numerical Investigations Of Tubular-Shaped Direct Methanol Fuel Cells (Dmfcs), Travis R. Ward

Master's Theses

This study focuses on both the numerical and experimental investigations of the novel, passively operated, tubular-shaped, Direct Methanol Fuel Cell (DMFC) as an alternative geometry to the traditional planar-shaped fuel cell. The benefit of the tubular geometry compared to the planar geometry is the higher instantaneous volumetric power density provided by the larger active area, which could be beneficial in applications that require a high instantaneous power while occupying a small volume. First, a two-dimensional, two-phase, non-isothermal model was developed to investigate the steady-state performance and design characteristics of a tubular-shaped, passive DMFC. It was found that a higher ambient …

Reconfigurable Sampling For Enhanced Energy Efficiency In Power-Constrained Wireless Systems, Timothy Kurp

Master's Theses

Advancement in microelectronics and wireless communications has nurtured the development of low power and low cost wireless systems such as sensor networks. Each node is typically driven by a battery, which has a limited energy capacity that directly constrains node, and network lifetime. This presents a bottleneck for the widespread exploitation of wireless sensing technology. Therefore, improving the energy efficiency of wireless sensing devices is of critical importance and has attracted the attention of the research community.

In this work, a data-driven method has been proposed and systematically investigated. Specifically, this technique reconfigures, in real time, the rate of data …

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Shaped Mems Contact, Ronald A. Coutu Jr., Paul E. Kladitis, Robert L. Crane

AFIT Patents

A MEMS switch fabrication process and apparatus inclusive of a bulbous rounded surface movable contact assembly that is integral with the switch movable element and achieving of long contact wear life with low contact electrical resistance. The disclosed process is compatible with semiconductor integrated circuit fabrication materials and procedures and includes an unusual photoresist reflow step in which the bulbous contact shape is quickly defined in three dimensions from more easily achieved integrated circuit mask and etching-defined precursor shapes. A plurality of differing photoresist materials are used in the process. A large part of the contact and contact spring formation …

Electromagnetic Modeling And Measurement Of Adaptive Metamaterial Structural Elements, Matthew E. Jussaume

Theses and Dissertations

This document addresses two major obstacles facing metamaterial development: uncertainty in the characterization of electromagnetic field behavior in metamaterial structures and the relatively small operational bandwidth of metamaterial structures. To address the first obstacle, a method of prediction aided measurement is developed and exploited to examine the field interactions within metamaterial devices. The fusion of simulation and measurement techniques enhances the understanding of the physical interactions of fields in the presence of metamaterials. To address the second obstacle, this document characterizes the effectiveness of an adaptive metamaterial design that incorporates a microelectromechanical systems (MEMS) variable capacitor. Applying voltages to the …

Optimization Design Of Electrodes For Anode-Supported Solid Oxide Fuel Cells Via Genetic Algorithm, Junxiang Shi, Xingjian Xue

Faculty Publications

Porous electrode is the critical component of solid-oxide fuel cells (SOFCs) and provides a functional material backbone for multi-physicochemical processes. Model based electrode designs could significantly improve SOFC performance. This task is usually performed via parameter studies for simple case and assumed property distributions for graded electrodes. When nonlinearly coupled multiparameters of electrodes are considered, it could be very difficult for the model based parameter study method to effectively and systematically search the design space. In this research, the optimization approach with a genetic algorithm is demonstrated for this purpose. An anode-supported proton conducting SOFC integrated with a fuel supply …

Mems-Based Pufs For Cryptographic Applications, Nicholas Shane Patrick

Honors Capstone Projects and Theses

No abstract provided.

The Influence Of Branches In The Performance Of Power-Line Communication Systems That Use Mc-Coma With Reed Solomon Coding, Emmanuel Felix

Tanzania Journal of Engineering and Technology (TJET)

Power-line network is proposed as an infrastructure for Information and Communications Technologies (ICTs)
services provision. However, there are a number of factors that contribute greatly to power-line communication performance degradation. These include number of branches that can be added or removed from the power- line network, lengths of the branch lines, loading etc. It has been pointed out that the number of branches is one of the factors that affects power-line performance to a certain extent. In this paper the influence of number of branches on the performance of Broadband Power-line communication (BPLC) that uses MC- CDMA modulation scheme with …