Computer-Aided Engineering and Design Commons^™

Composite Recycler: Frame, Alfonso Olivera

All Undergraduate Projects

How can composites be recycled? The Composite Recycler is an ongoing project that started in September 2017. The purpose of this project was to create a machine that will delaminate the composites, cut them, and heat them up to separate the resin from the composites so they can be recycled. A group was put together for the 2018-2019 academic year to further the project as a whole improve the operation of the device. The existing base was used as well as the cutter and the power sources. The upgrades included; a housing to support the transport rollers and changing from …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

A Computational Study Of Patch Implantation And Mitral Valve Mechanics, Dara Singh

Theses and Dissertations--Mechanical and Aerospace Engineering

Myocardial infarction (i.e., a heart attack) is the most common heart disease in the United States. Mitral valve regurgitation, or the backflow of blood into the atrium from the left ventricle, is one of the complications associated with myocardial infarction. In this dissertation, a validated model of a sheep heart that has suffered myocardial infarction has been employed to study mitral valve regurgitation. The model was rebuilt with the knowledge of geometrical changes captured with MRI technique and is assigned with anisotropic, inhomogeneous, nearly incompressible and highly non-linear material properties. Patch augmentation was performed on its anterior leaflet, using a …

Fatigue Tester, Nicholas Fazio

Williams Honors College, Honors Research Projects

The purpose of this project is to combine all my experience, knowledge and skills that I’ve acquired over the years as a Mechanical Engineering Technology student to completely design and build a fatigue tester. This will give me valuable experience in the process of designing and assembling a product and give me a great example to add to my portfolio. The tester will be completed through a process of researching design and modeling. Once everything is properly calculated and designed the parts that can be fabricated will. The rest will be ordered and then everything will be assembled. Upon completion, …

Landing-Gear Impact Response: A Non-Linear Finite Element Approach, Tuan H. Tran

UNF Graduate Theses and Dissertations

The primary objective of this research is to formulate a methodology of assessing the maximum impact loading condition that will incur onto an aircraft’s landing gear system via Finite Element Analysis (FEA) and appropriately determining its corresponding structural and impact responses to minimize potential design failures during hard landing (abnormal impact) and shock absorption testing. Both static and dynamic loading condition were closely analyzed, compared, and derived through the Federal Aviation Administration’s (FAA) airworthiness regulations and empirical testing data.

In this research, a nonlinear transient dynamic analysis is developed and established via NASTRAN advanced nonlinear finite element model (FEM) to …

Dynamic Response Of A Hingeless Helicopter Rotor Blade At Hovering And Forward Flights, Pratik Sarker

LSU New Orleans Theses and Dissertations

The helicopter possesses the unrivaled capacity for vertical takeoff and landing which has made the helicopter suitable for numerous tasks such as carrying passengers and equipment, providing air medical services, firefighting, and other military and civil tasks. The nature of the aerodynamic environment surrounding the helicopter gives rise to a significant amount of vibration to its whole body. Among different sources of vibrations, the main rotor blade is the major contributor. The dynamic characteristics of the hingeless rotor consisting of elastic blades are of particular interest because of the strongly coupled equations of motion. The elastic rotor blades are subjected …

The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley

Graduate Theses and Dissertations

In the realm of additive manufacturing there is an increasing trend among makers to create designs that allow for end-users to alter them prior to printing an artifact. Online design repositories have tools that facilitate the creation of such artifacts. There are currently no rules for how to create a good customizable design or a way to measure the degree of customization within a design. This work defines three types of customizations found in additive manufacturing and presents three metrics to measure the degree of customization within designs based on the three types of customization. The goal of this work …

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

Daimscale — 1:14th Tractor-Trailer For Testing Driver Assistance Technology, Christopher Marrale, Jase Sasaki, Devin Bodmer

Mechanical Engineering

Active driver assistance systems are becoming increasingly wide-spread throughout the automotive industry due to their potential for safer roads and decreased costs of transportation, but testing these systems on real trucks can be time consuming, dangerous, and costly. Testing these systems on a small-scale tractor-trailer combination will lead to faster and more efficient development of driver assistance systems and can be used by both engineers and students, leading to a larger field of experienced developers to improve these systems.

Our goal will be to design, manufacture, and build a scale 6x2 model of the tractor portion of a Daimler semi-truck …

Universal Studios Hollywood Vip Trolley - Roller Frame, Jeffrey Ploss, Chase Montague, Lincoln Treanor

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Cal Poly Rotor Recovered Rocket, Melissa Woodard

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Novelis Teaching Table, Phillip Laplante, Robert Hemker, Taylor Mcgriff, Juan Restrepo, Shelly Abraham

KSU Journey Honors College Capstones and Theses

Novelis is a company that specializes in metal casting, recycling, and rolling. They primarily focus on aluminum rolling for cans and car bodies but are an industry leader in numerous related areas. As the rolling process is not taught in most general engineering courses, Novelis periodically teaches new engineers and technicians about the specifics of this relatively mathematically complex process. Most of the current teaching methods are through PowerPoint presentations and group exercises, with minimal hands-on involvement. One of the most useful tools for teaching the rolling process is an actual jeweler’s rolling mill, which Novelis currently possesses, but is …

A 2-D Finite Element Modeling And Simulation Of 3-Roll Forming, Wenbo Zhao

LSU Master's Theses

Medium to large diameter carbon steel pipes are widely used in various applications such as gas and fluid transportation, tunnels construction and building construction. Based on manufacturing techniques and characteristics, they are mainly categorized into three categories: Seamless pipe, Butt-welded pipe and Spiral pipe. The forming of butt-welded and spiral pipe is often performed by a technique called 3-roller bending. While traditional trial-and-error method is costly, the geometry complexity, along with material nonlinearity makes exact theoretical analysis difficult unless heavy simplified assumptions are made. While the forming parameters in the 3-roller forming process of butt-welded pipe has been studied in …

H.F. Hauff Electric Pruner Drive Train, Grady Graff

All Undergraduate Projects

The H.F. Hauff Company invests a large amount of money in developing a quality pruner used in everyday agriculture. Modern electric pruners tend to be expensive while manual tree pruning is very physically demanding. A battery assisted pruner that is light-weight, ergonomic, inexpensive to build and powerful enough to cut branches that a nominal apple tree would possess is the direct affiliation that H.F. Hauff devotes its funding too. A team of engineering students from Central Washington University developed a product with consideration to each of these circumstances. Since hand drills have proven to be user friendly and of abundance …

Exercise Machine Generator, Duane Harbick

All Undergraduate Projects

Exercise “spinning bikes” and bicycle training stands are common ways to maintain fitness and train for cycling. This exercise necessitates the user putting work into the machine by means of pedaling. In many instances the work put into exercise bikes and training stands is not taken advantage of. The objective of this project is an attempt to make use of some of the energy that a person would usually expend during exercise by building a generator that interfaces with multiple spinning bikes and training stands. It uses a synchronous pulley system to interface with the exercise machine and spin a …

Equibiaxial Flexural Strength Testing Of Advance Ceramics, Ryan T. Jordan

Honors Undergraduate Theses

Ceramics are very important materials with many unique properties used in numerous industrial applications. Ceramics could be very hard and very strong in comparison to metals; however, they are very brittle, thus they are prone to instantaneous and catastrophic failure. Therefore, their reliability is compromised and it is very important to have advanced techniques that allow evaluating their mechanical behavior in many unusual stress states. One of such testing methods is biaxial strength method, that allows to measure properties not only unidirectional, but also in a biaxial way. The research work for this thesis will be built on design and …

Modeling And Analysis For Driveline Jerk Control, Prince Lakhani

Dissertations, Master's Theses and Master's Reports

In modern-day automotive industry, automotive manufacturers pay keen attention to driver’s safety and comfort by ensuring good vehicle drivability, feel of acceleration, limiting jerk and noise. The vehicle driveline plays a critical role to meet these criteria. By using high-fidelity simulation tool such as AMESim®, it is now possible to accurately model the vehicle driveline to be tested for different scenarios. With Simulink®, one can develop an efficient torque-based control system to limit the driveline oscillations and the generated noise. So, a joint simulation is used which provides a platform to evaluate the estimators and control system while considering the …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

LSU New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Micro-Architectured Metamaterials: Design And Analysis, Li Ai

Mechanical Engineering Research Theses and Dissertations

Metamaterials are engineered materials with unusual properties deriving mainly from their micro-architectures rather than composition. They have attracted increasing attention owing to their tailorable multi-functional properties that cannot be exhibited by naturally-occurring or traditionally-manufactured materials. Materials with a negative Poisson’s ratio (PR) and materials with a non-positive coefficient of thermal expansion (CTE) are examples of mechanical metamaterials. In this dissertation, metamaterials with negative Poisson’s ratios and negative coefficients of thermal expansion are designed using both heuristic approaches and topology optimization methods.

Firstly, based on a star-shaped re-entrant structure, three two-dimensional (2-D) periodic cellular materials are developed, which can be tailored …

Usa Boccia Ball Ramp For Athletes With Quadriplegia, Alissa A. Koukourikos, Matthew Lee, Nathan Bernards

Mechanical Engineering

In this report, the design process in creating an assistive device for Boccia Classification 3 (BC3) players is outlined. The initial research steps, including research into the rules of the game, capabilities of the players, and existing products is documented to show where ideas for the product stemmed from. This transitions into requirements that the sponsor requested, and preliminary designs and ideas for the product. Finally, this report explains the details of the final design, which has been analyzed for safety, ease of use, and ability to function under different conditions. The processes of manufacturing and testing will also be …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Answering Food Insecurity: Serving The Community With Food And Knowledge Using Technology, Courtney Simpson

Purdue Journal of Service-Learning and International Engagement

The courses of Tech120, CGT110, and ENGT 180/181 and Red Gold at Purdue collaborated to design a robot that would plant and water a garden for a local community charter school. The students centered the project on the users’ needs for fresh food, nutrition education, and early exposure to STEM for children. The school, Anderson Preparatory Academy (APA), is comprised of many children who come from low-income families and are in the free or reduced lunch program. Inspired from “Farm Bot,” a similar system that allows for almost hands-free gardening, the “Boiler Bot” is designed to be scalable so children …

Cam-Based Pose-Independent Counterweighting For Partial Body-Weight Support In Rehabilitation, Ashish Shinde

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents the design and testing of a body weight support system for gait training in a two-dimensional workspace. Extension of the system to a three-dimensional workspace is not within the scope of this thesis.

Gait dysfunctions are changes in normal walking patterns, often related to a disease or abnormality in different areas of the body. There are numerous body weight support (BWS) systems present in the market which are applied to rehabilitation scenarios in mobility recovery like in gait training. But most of these BWE systems are costly and generally are stationary devices. A major drawback of such …

Development Of Portable Hyperspectral Imaging Device, Chenxi Li, Youngkee Jung, Iyll-Joon Doh, Euiwon Bae

The Summer Undergraduate Research Fellowship (SURF) Symposium

Most of the conventional hyperspectral imaging devices require sophisticated optical components, occupy a large footprint, and requires an initial capital investment for laboratories which mostly suits for laboratories benchtop system. The requirement of shipping the sample and waiting an extended period of time to get the results are the main downsides of this traditional approach. Capitalize in many specific field applications and diagnosis, portable devices provide both convenience and on-site results which are desirable for government agencies and food safety inspectors. This project was aimed to develop a low-cost, portable hyperspectral device for food safety applications. A smartphone was used …

Development Of The End-Effector Of A Cable-Driven Parallel Manipulator For Automated Crop Sensing, Iman Salafian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A four cable-driven parallel manipulator (4CDPM), consisting of sophisticated spectrometers and imagers, is under development for use in acquiring phenotypic and environmental data over an acre-sized maize field. This thesis presents the design, controls, and testing of two sub-systems in a 4CDPM: a Center of Mass Balance System (CMBS) and a Drop-Down System (DDS).

One of the factors that influences stability is the center of mass (COM) position of the end effector. An offset in COM can cause a pendulum effect or an undesired tilt angle. A center of mass balancing system is presented in this thesis to minimize the …

A Study In The Use Of Elastic Materials In Expandable Containment Units, Andrew J. Eisenman, Joby Anthony Iii, David Satagaj

Montview Journal of Research & Scholarship

The rigidity of materials in conjunction with the aspect of elasticity has been a concern of modern technologies and construction in recent centuries because of the advantages that expandable storage would bring to the fields of containment units with respect to population growth and space exploration. The world population is currently growing at an exponential rate, and as our population grows, the more important it will become to have containment units that can both contain large volumes of material as well as minuscule amounts of material without wasting space. In order accomplish this, we will need a new type of …

Automation In Entertainment: Concept, Design, And Application, Ryan Thally

Undergraduate Honors Theses

The focus of this thesis is to explore the automation technology used in the modern entertainment industry. Upon completion of my thesis, I will deliver a working prototype of the chosen technology and present its capabilities in a choreographed show.

High Accessibility Cabinet Insert, Matthew Leal

All Undergraduate Projects

Watching grandparents and parents get older, the struggle of day-to-day activities generally increases. One of the most recurring issues the older generation experiences nearly daily is their inability to reach dishes, glassware, and other things on the topmost shelves of a kitchen. Not only is it difficult for them to use things such as stepstools, it also becomes increasingly dangerous. With age, a fall from any height could be catastrophic. With this scenario in mind, a user-friendly cabinet insert would be a very effective way to combat this issue. However, many existing models of cabinet designed to fit these requirements …

Pin Router Duplicator, Daniel Phan

All Undergraduate Projects

The purpose of this project is to develop a pin router duplicator to accurately produce guitar bodies, necks, and fret boards. The pin router duplicator is designed to speed up the production process for the class Lean Manufacturing (MET 345), offered at Central Washington University. In the class, students learn how to work as a team to improve the way a woodshop is ran. In Lean Manufacturing, guitar bodies, necks, and fret boards are produced by using a CNC router. For this project, the motivation is to increase production by reducing production time. Accuracy and repeatability is also taken into …