Open Access. Powered by Scholars. Published by Universities.®

Computer-Aided Engineering and Design Commons™

Open Access. Powered by Scholars. Published by Universities.®

Applied Mechanics

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 211 - 217 of 217

Full-Text Articles in Computer-Aided Engineering and Design

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor Jun 2006

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

Go to article

Evaluation Of Accuracy And Efficiency Of Some Simulation And Sampling Methods In Structural Reliability Analysis, Christopher D. Eamon, Michel D. Thompson, Zhenyu Liu Jul 2005

Evaluation Of Accuracy And Efficiency Of Some Simulation And Sampling Methods In Structural Reliability Analysis, Christopher D. Eamon, Michel D. Thompson, Zhenyu Liu

Civil and Environmental Engineering Faculty Research Publications

Numerous simulation and sampling methods can be used to estimate reliability index or failure probability. Some point sampling methods require only a fraction of the computational effort of direct simulation methods. For many of these methods, however, it is not clear what trade-offs in terms of accuracy, precision, and computational effort can be expected, nor for which types of functions they are most suited. This study uses nine procedures to estimate failure probability and reliability index of approximately 200 limit state functions with characteristics common in structural reliability problems. The effects of function linearity, type of random variable distribution, variance, …

Go to article

Effect Of Edge-Stiffening And Diaphragms On The Reliability Of Bridge Girders, Christopher D. Eamon, Andrzej S. Nowak Mar 2005

Effect Of Edge-Stiffening And Diaphragms On The Reliability Of Bridge Girders, Christopher D. Eamon, Andrzej S. Nowak

Civil and Environmental Engineering Faculty Research Publications

Secondary elements such as barriers, sidewalks, and diaphragms may affect the distribution of live load to bridge girders. The objective of this study is to evaluate their effect on girder reliability if these elements are designed to be sufficiently attached to the bridge so as not to detach under traffic live loads. Simple span, two lane structures are considered, with composite steel girders supporting a reinforced concrete deck. Several representative structures are selected, with various configurations of barriers, sidewalks and diaphragms. Bridge analysis is performed using a finite element procedure. Load and resistance parameters are treated as random variables. Random …

Go to article

Modeling Concrete Masonry Walls Subjected To Explosive Loads, Christopher D. Eamon, James T. Baylot, James L. O'Daniel Aug 2004

Modeling Concrete Masonry Walls Subjected To Explosive Loads, Christopher D. Eamon, James T. Baylot, James L. O'Daniel

Civil and Environmental Engineering Faculty Research Publications

Concrete masonry unit walls subjected to blast pressure were analyzed with the finite element method, with the goal of developing a computationally-efficient and accurate model. Wall behavior can be grouped into three modes of failure, which correspond to three ranges of blast pressures. Computational results were compared to high-speed video images and debris velocities obtained from experimental data. A parametric analysis was conducted to determine the sensitivity of computed results to critical modeling values. It was found that the model has the ability to replicate experimental results with good agreement. However, it was also found that, without knowledge of actual …

Go to article

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo Jun 2004

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Go to article

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna Dec 1999

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Go to article

Virtual Reality Modelling Of A Cnc Machine, Damian O'Sullivan Jan 1998

Virtual Reality Modelling Of A Cnc Machine, Damian O'Sullivan

Theses

The increasing importance of training and upgrading skills has led to the use of new interactive technologies in the development of more effective training tools. Previous techniques for training Computer Numerical Control (CNC) machine operators, while excellent for their time, varied from brief inexpensive tutorials to expensive on the job training. A CNC machine uses a computer to perform the functions of the machine using a part program stored in the memory of the computer. This thesis describes a Virtual Reality (VR) model of a CNC milling machine, implemented within a VR environment representing a CNC workshop. Its development and …

Go to article

First Prev