Biomechanical Engineering Commons^™

Development Of A Technique To Diagnose Subtalar Joint Instability, Ajaya Dhakal

Mechanical & Aerospace Engineering Theses & Dissertations

Most patients escape diagnosis of subtalar joint instability for years before treatment. Therefore, a clinically relevant technique to diagnose subtalar joint instability will improve its management. Towards this goal, a six degree of freedom positioning and loading device was developed to apply physiologic loads to the hindfoot. Because the ideal loading configuration to detect subtalar joint instability is unknown, the device was designed to apply rotational and translational forces simultaneously. Specifically, plantarflexion/dorsiflexion, inversion/eversion, and internal/external rotation can be applied individually or as coupled motions along with an anterior/posterior drawer. Kinematic data were collected from calcaneus, talus and tibia using a …

Experimental Analysis And Modeling Validation Of A Knee Brace In Shock Mitigation, Manish Prakash Dhekane

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental setup simulating the dynamic environment in a high sea state is developed for the lower extremities to study the mitigation of shock impact. A single degree of freedom machine is equipped with six linear induction motors to produce impact acceleration ranging from 0.5G to 4G. The experiments are carried out along the dummy leg by using two configurations, one without a knee brace and one with a knee brace. Force and acceleration data is collected using a data acquisition system.

To develop the analytical model of the same experimental setup, the knee brace and dummy leg were scanned …

Optimization Of The Seating Position In A Human-Powered Vehicle, Y. Lei, Mohamed Trabia, D. Too

Mechanical Engineering Faculty Research

Until recently, most of the human-powered vehicles (HPV) were designed focusing solely on its aerodynamics characteristic. In many of these HPV designs, the rider seating position was arbitrarily chosen without consideration of its effect on the rider's comfort and cycling effectiveness. Also, there is no guarantee that the seating position is related to maximum power output. Too (1991) used an experimental approach to determine that the rider will produce the maximum anaerobic power when the seat tube angle of a bicycle is at 75° whereas Hull and Gonzalez (1990) used an engineering approach to optimize the cycling biomechanics. However several …

Designing Yards For Sheep, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

This article has been adapted from a report of the 1976 Sheep and Wool Refresher Course.

The officers attending the Course inspected W. A. farms, and then met in groups to discuss what they had seen, and to pool their experience in compiling a report. This article has been adapted from the report of the group working on the topic "Sheep yards and facilities".

The W. A. representative in the group working on sheep yard design was Mr John Wise of the Department's Katanning office.

The principals discussed here should help farmers either design new sheep yards, or improve the …

Bulletin No 3883 - Dairying In W.A., Western Australian Department Of Agriculture

Bulletins - 3000 - 3999

Western Australia has a small dairy industry compared with its other rural production. However, the industry has consolidated over recent years.

Tree clearing and pasture development on existing holdings and the amalgamation of small dairy farms has led to a rapid increase in the area of pasture per farm. The trend in Western Australia is towards bigger herds, more efficient dairies, more fodder conservation and increasing production per cow and per· hectare.

The Setting And Control Of Disc Ploughs, P A. Taylor

Journal of the Department of Agriculture, Western Australia, Series 4

THE trailed disc plough is the most commonly used tillage implement in Australian broadacre farming, yet it is considered in some areas to be difficult to set and to operate. These notes provide information resulting from C.S.I.R.O. research to assist operators in the control and operation of trailed disc ploughs.

Four Mobile Picking And Pruning Platforms For Orchards, J C. Rowbotham

Journal of the Department of Agriculture, Western Australia, Series 4

Shifting ladders around the orchard takes a great deal of time and effort at picking and pruning time.

This article describes four home made labour savers which take most of the ladder work out i f these operations.

W.A. Dairying : Progress In 42 Years, Maurice C. Cullity

Journal of the Department of Agriculture, Western Australia, Series 4

From hardship and elementary standards, West Australian dairying has developed into a consolidated industry with larger herds, increased output and high quality production.

The changes he has seen are reviewed by Mr. M. Cullity who retired last month from the position of Chief of the Division of Dairying, after 42 years of service to the industry.

THE history of Western Australia's dairying industry has been a story of struggle against hardship, marketing problems and adverse criticism.

In spite of this the industry has steadily grown and greatly improved its efficiency.

The Importance Of Rapid And Complete Milking, K Needham, W. G. Robinson

Journal of the Department of Agriculture, Western Australia, Series 4

COMPLETE withdrawal of milk from the udder as quickly as possible after the process of "let-down" has started, is an essential in good milking; management.