Mechanical Engineering Commons^™

Aerosol Transport By Coughing In A Depressurized And Air-Conditioned Chamber, Bo Zhang

Dissertations

Expiratory droplets from human coughing in an air-conditioned environment have always been considered to be potential carriers of pathogens, responsible for respiratory disease transmission. The air movement/circulation and ambient conditions such as pressure and temperature are all key factors of aerosol transport. To study the transmission of disease by human coughing in a depressurized air-conditioned chamber, there are many technical challenges, including the following: 1) the study of simulating human coughing; 2) the collection of aerosol generated by coughing; 3) the CFD simulation of coughing-induced aerosol transport in an air-conditioned chamber; 4) the validation of such a CFD simulation by …

Cfd Simulations Of Chemical Looping Combustion In A Packed Bed And A Bubbling Bed Fuel Reactor, Guanglei Ma

McKelvey School of Engineering Graduate Student Theses & Dissertations

Chemical-looping combustion (CLC) is a next generation combustion technology that has shown great promise in addressing the need for high-efficiency low-cost carbon capture from fossil fueled power plants to address the rising carbon emissions. Although there have been a number of experimental studies on CLC in recent years, CFD simulations have been limited in the literature on CLC. The development and confidence in high-fidelity simulations of the CLC process is a necessary step towards facilitating the transition from laboratory-scale experiments to deployment of this technology on an industrial scale. In this research, first the CFD simulations of a CLC packed …

Evaluation Of Flux Correction On Three-Dimensional Strand Grids With An Overset Cartesian Grid, Dalon G. Work

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Simulations of fluid flows over complex geometries are typically solved using a solution technique known as the overset meshing method. The geometry is meshed using grid types appropriate to the local geometry in a patchwork fashion, rather than meshing the entire geometry with one type of mesh. The strand-Cartesian approach is a simplification of this process. While high-order accurate solvers on Cartesian grids are simple to implement, strand grids are usually restricted to second-order accuracy, resulting in poor quality solutions. Flux correction is a high-order accurate solution method, specifically designed for use on strand grids. The flux correction method on …

Development Of An Analysis And Design Optimization Framework For Marine Propellers, Ashish C. Tamhane

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a framework for the analysis and design optimization of ship propellers is developed. This framework can be utilized as an efficient synthesis tool in order to determine the main geometric characteristics of the propeller but also to provide the designer with the capability to optimize the shape of the blade sections based on their specific criteria.

A hybrid lifting-line method with lifting-surface corrections to account for the three-dimensional flow effects has been developed. The prediction of the correction factors is achieved using Artificial Neural Networks and Support Vector Regression. This approach results in increased approximation accuracy compared …

Effect Of Design Parameters On Thermal Performance Of A Vane Type Disc Brake Rotor, Yogesh Satish Dalal

Masters Theses

The ever-increasing need of effective transportation puts automobile manufacturers in a situation of continuous improvement and innovate the safety systems. The brake system of an automobile has always been considered as one of the most critical active safety systems. Thermal characteristics of the brake are an important aspect to consider for brake disc durability and performance. The convective cooling of a brake disc is an important factor since design changes in the brake rotor can significantly improve cooling characteristics. The focus of this research is to study and optimize the disc brake rotor for a given heat dissipation rate and …

Formula Sae Intake System, Esa Mahmood, Arman Sarwar, Michael R. Smith

Capstone Design Expo Posters

The Formula SAE Intake System is intended to optimize the airflow into a restricted 600cc engine. The intake system is designed, fabricated, and installed in accordance with the FSAE rule book with a focus on maximizing the vehicle’s acceleration. It is directly responsible for determining the drivability of the car and how much horsepower the flow restricted engine produces.

Design of the intake was conceptualized based on researching a number of factors including venturi diffusion angles, plenum volumes, and runner lengths. Initial tests were performed utilizing computational fluid dynamics for a total of 367 flow simulations and 261 running hours …

A Physics-Based Approach To Modeling Wildland Fire Spread Through Porous Fuel Beds, Tingting Tang

Theses and Dissertations--Mechanical and Aerospace Engineering

Wildfires are becoming increasingly erratic nowadays at least in part because of climate change. CFD (computational fluid dynamics)-based models with the potential of simulating extreme behaviors are gaining increasing attention as a means to predict such behavior in order to aid firefighting efforts. This dissertation describes a wildfire model based on the current understanding of wildfire physics. The model includes physics of turbulence, inhomogeneous porous fuel beds, heat release, ignition, and firebrands. A discrete dynamical system for flow in porous media is derived and incorporated into the subgrid-scale model for synthetic-velocity large-eddy simulation (LES), and a general porosity-permeability model is …

Development Of An Evaporation Sub-Model And Simulation Of Multiple Droplet Impingement In Volume Of Fluid Method, Sathya Prasad Potham

Dissertations, Master's Theses and Master's Reports

Droplet collision and impingement on a substrate are widely observed phenomenon in many applications like spray injection of Internal Combustion Engines. Existing Lagrangian models do not provide a comprehensive picture of the outcome of these events and may involve model constants requiring experimental data for validation. Physics based models like Volume of Fluid (VOF) method involve no parametric tuning and are more accurate. The aim of this thesis is to extend the basic VOF method with an evaporation sub-model including an additional vapor phase and implement this model in an open source Computational Fluid Dynamics (CFD) software, OpenFOAM. The new …

Assessment Of Varying Model Representations In Cfd Simulations, Caitlin R. Gerdes

Electronic Theses and Dissertations

This thesis investigates the effects of varying model refinement and representation of computational fluid dynamics (CFD) simulations in two case studies. Product and process realization in engineering design requires substantial resources (time and money) in order to test novel designs for effectiveness. In recent decades, engineering has been relying more heavily on simulation-based analysis in the design process with computer models to help reduce the demands for real-life testing. The first case study analyzed in this thesis is a photobioreactor, which is used to grow microalgae for biofuel and require a balance of nutrients, light, and mixing for growth. The …

Experimental And Numerical Study Of Dysphagia, Yash G. Potdar

Masters Theses

Dysphagia, meaning difficulty in swallowing, is a symptom of disease that occurs in young children and elderly people. It occurs particularly due to two reasons, weak neural network and/or deformities in oral section/s. The Helen DeVos Children’s Hospital’s Intensive Feeding Program takes care of children suffering from Dysphagia. In order to make the swallowing process easier and in some cases safer, thickener is added to the liquids. Depending on the requirement of thickness, the amount of thickener is varied. Although the directions to prepare the mixtures are given by the thickener product company, the required thickness is not achieved when …

Optimization Of Water And Energy Use In Indirect Evaporative Cooling System By Cfd, Mansi Vijay Prajapati

Mechanical and Aerospace Engineering Theses - Archive

Data center cooling is becoming important to maintain environmental condition for ITE- Information technology equipment. Conventional evaporative wet cooling media lowers the temperature of the dry bulb temperature of incoming air in which heat transfer to water film and sensibly cool the product air by increasing moisture into air. Wet cooling media technique requires large quantity of clean water, which is reducing area where water is very less. Therefore, indirect evaporative cooling is good alternative. Chiller plants/Indirect Evaporative cooling(IEC) are used as a cooling source for larger data centers as they are more efficient in heat transfer without adding moisture …

Experimental, Theoretical And Computational Modeling Of Flow Boiling, Flow Condensation And Evaporating Falling Films, Chirag Rajan Kharangate

Open Access Dissertations

The transition from single-phase to two-phase thermal systems in future space vehicles demands a thorough understanding of phase change methods in reduced gravity, including microgravity. In this study, phase change methods like flow boiling, flow condensation and evaporative falling-films are investigated experimentally, theoretically and computationally.

The experimental part of the study consists of an investigation of the influence of inlet subcooling and two-phase inlet on flow boiling heat transfer and critical heat flux in a horizontal 2.5-mm wide by 5-mm high rectangular channel in different orientations with respect to Earth gravity using FC-72 as working fluid. High-speed video imaging is …

Comparison Of Airfoil Precomputational Analysis Methods For Optimization Of Wind Turbine Blades, Ryan Barrett, Andrew Ning

Faculty Publications

The objective of this research was to develop and compare various airfoil precomputational parameterization and analysis techniques for aerostructural optimization of wind turbine blades. The airfoils along the blade were added as optimization design variables through pre-computational parameterization methods using thickness-to-chord ratios and blended airfoil family factors. The airfoils' aerodynamic performance was analyzed with three methods of increasing fidelity: a panel method (XFOIL), Navier-Stokes based computational fluid dynamics (RANS CFD), and wind tunnel data. The optimizations minimized mass over annual energy production (m/AEP) and thereby approximated the minimization of cost of energy. The results were compared to the NREL 5-MW …

Experimental And Computational Study Of Gas Bubble Removal In A Microfluidic System Using Nanofibrous Membranes, Hamed Gholami Derami, Ravindra Vundavilli, Jeff Darabi

SIUE Faculty Research, Scholarship, and Creative Activity

This paper presents a simple and efficient method for removing gas bubbles from a microfluidic system. This bubble removal system uses a T-junction configuration to generate gas bubbles within a water-filled microchannel. The generated bubbles are then transported to a bubble removal region and vented through a hydrophobic nanofibrous membrane. Four different hydrophobic Polytetrafluorethylene (PTFE) membranes with different pore sizes ranging from 0.45 to 3 μm are tested to study the effect of membrane structure on the system performance. The fluidic channel width is 500 μm and channel height ranges from 100 to 300 μm. Additionally, a 3D computational fluid …

Implementations Of Fourier Methods In Cfd To Analyze Distortion Transfer And Generation Through A Transonic Fan, Marshall Warren Peterson

Theses and Dissertations

Inlet flow distortion is a non-uniform total pressure, total temperature, or swirl (flow angularity) condition at an aircraft engine inlet. Inlet distortion is a critical consideration in modern fan and compressor design. This is especially true as the industry continues to increase the efficiency and operating range of air breathing gas turbine engines. The focus of this paper is to evaluate the Computational Fluid Dynamics (CFD) Harmonic Balance (HB) solver in STAR-CCM+ as a reduced order method for capturing inlet distortion as well as the associated distortion transfer and generation. New methods for quantitatively describing and analyzing distortion transfer and …

Maximizing Use Of Air-Side Economization, Direct And Indirect Evaporative Cooling For Energy Efficient Data Centers, Betsegaw Kebede Gebrehiwot

Mechanical and Aerospace Engineering Dissertations - Archive

Data centers house information technology (IT) equipment such as servers and network switches which are vital for our networked modern society by providing digital data storage, data processing and connectivity. Data centers house few hundreds to tens of thousands of IT equipment that consume few kilowatt-hours to multi-megawatt-hours of electrical energy that gets dissipated as heat. IT equipment need to be properly cooled so that they operate reliably for their expected lifetime. For air cooled IT equipment, manufacturers provide heat sinks, cold plates, fans, et cetera to remove heat from the vicinity of heat dissipating components and data centers need …

Cfd Modelling Of Wet Cooling Media And Design Optimization Of Heat Sink For Data Center Application, Shivang Yogeshkumar Desai

Mechanical and Aerospace Engineering Theses - Archive

Air cooling is most widely used and economical method of currently available cooling technologies in which heat exchanger plays a vital role in facility designs. Evaporative cooling can be energy efficient than mechanical cooling because it uses water’s enthalpy of vaporization. Wet cooling pads can be used as the direct evaporative cooling system in which pad is made of cellulose fibers those gets wet when water injected. When hot and dry air passes through pad surfaces, water evaporates in the air which cools down air adiabatically increasing humidity. These type of cooling units can be installed in these type of …

Design Consideration And Steady State Study Of Thrust Bearings In High Speed Subsonic Applications, Arvind Prabhakar

Mechanical and Aerospace Engineering Theses - Archive

Thrust bearings are required to perform at high speeds in various turbomachinery applications causing the nature of fluid flow within the bearings to be in high subsonic as well as supersonic regimes. The motivation of this research is to develop a bearing performance prediction model tailored for high subsonic speeds and large Reynolds numbers. The prime fluid characteristics studied in the thin film for predicting the bearing performance has been achieved by carefully considering inertial, viscous as well as compressible effects within the thin film fluid flow. Fluid inertia is a vital physical phenomenon that plays an important role in …

Computational Study And Error Analysis Of An Integrated Sampling-Probe And Gas-Analyzer For Mixing Measurements In Supersonic Flows, Wenbo Zhu

Mechanical and Aerospace Engineering Theses - Archive

Concentration probes are employed in supersonic flow mixing experiments for binary gas mixture composition measurements. These measurements are fundamental for the advancement of the scramjet technology. While non-intrusive laser-based methods (such as planar laser-induced fluorescence and filtered Rayleigh scattering) have been developed greatly over the past few decades, intrusive methods (such as concentration probes) still play an essential role in the measurement of mixture composition due to the fact that, with correct application, they do not require further assumptions on the aerothermodynamic states of the investigated mixture, which are often difficult to corroborate. Conversely, such assumptions are essential to the …

Cfd Analysis Of Vapor Chamber With Micro Pillars As Heat Spreader For High Power Electronic Devices, Yasir Aziz Modak

Mechanical and Aerospace Engineering Theses - Archive

The recent trend in electronic industry shows that there is large power dissipation from the electronic devices and at the same time their sizes are getting smaller. This large power dissipation takes place in the form of releasing heat energy. It is observed that heat dissipation from the electronic devices is high and source size is small. The high device temperatures result in decreased reliability and increased failure rates. This difficulty can be addressed by controlling the temperatures at the source of heat generation. In chip scale package chip is the major source of heat generation. Thus our priority is …

Performance Evaluation Of Plate-Fin And Pin-Fin Heat Sinks For The Application Of Oil Immersion Cooling And Design Optimization Of Dynamic Cold Plate For The Application Of Warm Water Cooling, Parth Jayeshkumar Soni

Mechanical and Aerospace Engineering Theses - Archive

In IT industries, to keep server rooms and data centers cool is a constant challenge for hardware developers and the cooling solution providers. Air cooling is the most widely used approach for thermal management of servers in data centers from many years. However, the scenario is changing gradually as the computational ability of data center is increasing exponentially. Because of increasing computational ability, the heat generated by the servers is increased in such amount that air cooling is not as efficient as it was before. Hence, alternative cooling system is required. In 1970’s the idea of liquid cooling was introduced. …

Computational Fluid Dynamic Modeling Of Natural Convection In Vertically Heated Rods, Mahesh Surendran

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Natural convection is a phenomenon that occurs in a wide range of applications such as cooling towers, air conditioners, and power plants. Natural convection may be used in decay heat removal systems such as spent fuel casks, where the higher reliability inherent of natural convection is more desirable than forced convection. Passive systems, such as natural convection, may provide better safety, and hence have received much attention recently. Cooling of spent fuel rods is conventionally done using water as the coolant. However, it involves contaminating the water with radiation from the fuel rods. Contamination becomes dangerous and difficult for humans …

Development Of A Three-Dimensional High-Order Strand-Grids Approach, Oisin Tong

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The strand-Cartesian grid approach is a unique method of generating and computing fluid dynamic simulations. The strand-Cartesian approach provides highly desirable qualities of fully-automatic grid generation and high accuracy. This work focuses on development of a high-accuracy methodology (high-order scheme) on strand grids for two and three dimensions.

In this work, the high-order scheme is extended to high-Reynolds number computations in both two and three dimensions with the Spalart-Allmaras turbulence model and the Menter SST turbulence model. In addition, a simple limiter is explored to allow the high-order scheme to accurately predict discontinuous flows.

Extensive verification and validation is conducted …

Project Oasis: Optimizing Aquaponic Systems To Improve Sustainability, Siddharth Nigam, Paige Balcom

Honors Theses and Capstones

Started in Fall 2015, Project OASIS (Optimizing Aquaponic Systems to Improve Sustainability) is an interdisciplinary capstone project with the goal of designing a sustainable and affordable small-scale aquaponic system for use in developing nations to tackle the problems of malnutrition and food insecurity. Aquaponics is a symbiotic relationship between fish and vegetables growing together in a recirculating system. The project’s goals were to minimize energy consumption and construction costs while using universally available materials. The computational fluid dynamics (CFD) software OpenFOAM was used to create transient and steady-state models of fish tanks to visualize velocity profiles, streamlines, and particle movement. …

Analysis Of Road Vehicle Aerodynamics With Computational Fluid Dynamics, Christian Armando Mata

Open Access Theses & Dissertations

A road vehicles aerodynamics can be one of the most influential aspects of its performance. With the increased importance on fuel efficiency in recent years, new road vehicles are being developed smaller in size, with smaller displacement engines, as well as with improved aerodynamics. The aerodynamics of a vehicle can have a significant effect on its fuel efficiency, as well as other important aspects of the vehicles performance such as the top speed, acceleration, and handling. A study focusing on analyzing aerodynamic effects due to vehicle geometries such as wheels covered by the vehicles body in comparison to open wheels …

Design And Analysis Of An Axisymmetric Aerospike Supersonic Micro-Nozzle For A Refrigerant-Based Cold-Gas Propulsion System For Small Satellites, Abdalla Ali Bani

Masters Theses

"The cold-gas propulsion system being developed by M-SAT requires improvements to its original nozzle design. This study documents the research, design, and analysis of a supersonic plug nozzle concept that could be integrated to the refrigerant-based cold-gas propulsion system to possibly improve its performance. As documented in this thesis, CFD analysis showed that the outlined nozzle design method resulted in a feasible nozzle concept that has the ability to out-perform a conventional nozzle of the same area ratio. The flow-fields and thrust of the aerospike nozzle, for the full and truncated nozzles, were investigated. The purpose of this study is …

Inlet Distortion Effects On The Unsteady Aerodynamics Of A Transonic Fan Stage, Daniel Oliver Reilly

Browse all Theses and Dissertations

A computational study was conducted to understand the influence of aircraft inlet distortion flow on the unsteady aerodynamic loading of a gas turbine fan stage. A single stage, transonic fan design with no inlet guide vanes was modeled with a commercial, computational fluid dynamics solver, STAR-CCM+, using the harmonic balance technique. The baseline inlet boundary condition applied to the model is consistent with that of a homeomorphic variant of the M2129 S-duct, and exhibited stagnation pressure distortion and a swirl pattern. The baseline inlet flow was decomposed and parameterized into a set of inlet boundary conditions which were individually applied …

Parametric Study Of An Igbt Cold Plate And Affect Of Device Level Modelling On System Level Thermal Predictions, Abhishek Raj Urs Kadaba Nagaraja Urs

Mechanical and Aerospace Engineering Theses - Archive

In power electronics, as there is continuous increase in performance of the electronic devices, simultaneously the size of the components used in these devices keep on decreasing. This has resulted in increased power densities and the requirements for excellent cooling as well in order to avoid the failure of those devices. Traditionally, while designing a cooling system for a device, uniform heat flux is assumed throughout the components. In many cases this method may not be accurate for a particular model design. There are chances that the heat flux distribution around the components are non-uniform and requires a more accurate …

Application Of The Aeroacoustic Analogy To A Shrouded, Subsonic, Radial Fan., Bryan Buccieri

Electronic Theses and Dissertations

A study was conducted to investigate the predictive capability of computational aeroacoustics with respect to a shrouded, subsonic, radial fan. A three dimensional unsteady fluid dynamics simulation was conducted to produce aerodynamic data used as the acoustic source for an aeroacoustics simulation. Two acoustic models were developed: one modeling the forces on the rotating fan blades as a set of rotating dipoles located at the center of mass of each fan blade and one modeling the forces on the stationary fan shroud as a field of distributed stationary dipoles. Predicted acoustic response was compared to experimental data. The blade source …

Optimization Of Blalock-Taussig Shunt And Anastomotic Geometry For Vascular Access Fistula Using A Genetic Algorithm, Guangyu Bao

McKelvey School of Engineering Graduate Student Theses & Dissertations

Blalock-Taussig (BT) shunts are used for defects that affect the flow of blood from the right ventricle, through the pulmonary artery, and to the lungs. Arteriovenous (AV) fistula is one type of vascular access which is a surgically created vein used to remove and return blood during hemodialysis. Plastic grafts used in the above two reconstructions may result in areas of non-physiologic flow in the grafts leading to risk of stenosis (blocked area) and thrombosis, which is the single major cause for access morbidity. The focus of this thesis is to study BT shunts and anastomoses models using Computational Fluid …