Mechanical Engineering Commons^™

Development Of Distributed Off-Grid Renewable Energy System For Rural African Communities, Mateo Sebastian Guerrero, Menghong Feng

Engagement & Service-Learning Summit

Our Hybrid Energy System team is committed to develop low-cost renewable energy solutions to rural African communities where access to electricity from government grid is not available. According to a World Bank’s report, only 24% of sub-Saharan countries have access to electricity. Our team has been working with local partners to build renewable energy systems since 2008. From 2015 the team has been working on micro hydropower turbine and vertical-axis wind turbine with solar energy system combined. Our current efforts include a prototype design of a wind-solar system, using a new concept of vertical axis wind turbine to harvest wind …

Epics Torch, Madi Rogers, George Townsend, Brandon Henman, Holly Gregory, Patrick Leal, Brennan Mcpherron, Xinyue Pan

Engagement & Service-Learning Summit

The Indiana Bicentennial Commission (IBC) was created by former governor Mitch Daniels to plan and execute a statewide celebration of Indiana’s 200th birthday in 2016. The commission has requested that researchers at Purdue University develop a high-tech Indiana-made flame torch a la the Olympic torch to be used in the celebration and displayed throughout all 92 counties of the state. In addition, the IBC requested that Purdue’s EPICS program develop a kid-friendly torch that can be used alongside the actual torch in relays, celebrations, and community outreach events throughout the state.

By collaborating with Purdue researchers throughout a range of …

4-H Nfpa Fluid Power Challenge, Erika D. Bonnett

Engagement & Service-Learning Summit

The 4-H NFPA Fluid Power Challenge partnered Purdue Polytechnic Institute and Indiana 4-H with the National Fluid Power Association and Center for Compact and Efficient Fluid Power to provide teams of Indiana youth in 6-8th grades with opportunity to learn about hydraulics, engineering design, and other STEM skills. This created an opportunity to give youth a learning experience with STEM through hands-on, experiential learning activities. Youth experienced a one day workshop in which they worked as teams to learn concepts of fluid power through hands-on learning. Teams then went back to their communities and created and designed a fluid power …

Effect Of Plug In Hybrid Electric Vehicle Adoption On Gas Tax Revenue, Local Pollution, And Greenhouse Gas Emissions, Neil Mccall

Theses and Dissertations

Plug-in hybrid electric vehicles (PHEV) are likely to increase in popularity in the near future. However, the environmental benefits of PHEVs involve tradeoffs between the benefits of reduced tailpipe emissions against the drawbacks of increased emissions at marginal electric generation plants and reduced gasoline tax income. In this report, a model is developed that will enable these tradeoffs to be studied. The model accounts for local commuting patterns and marginal electric generation in New Jersey. The result allows the effect of PHEV adoption on gasoline tax, CO2, NOx and SOx to be predicted on a county level. Sample calculations are …

Towards Developing Product Applications Of Thick Origami Using The Offset Panel Technique, Michael R. Morgan, Robert J. Lang, Spencer P. Magleby, Larry L. Howell

Faculty Publications

Several methods have been developed to accommodate for the use of thick materials in origami models which preserve either the model’s full range of motion or its kinematics. The offset panel technique (OPT) preserves both the range of motion and the kinematics while allowing for a great deal of flexibility in design. This work explores new possibilities for origami-based product applications presented by the OPT. Examples are included to illustrate fundamental capabilities that can be realized with thick materials such as accommodation of various materials in a design and manipulation of panel geometry resulting in an increased stiffness and strength. …

Mentored Environment For Isogeometric Analysis, Kevin Tew, Michael Scott

Journal of Undergraduate Research

The mentored environment for isogeometric analysis (IGA) has trained engineering and computer science students to develop isogeometric numerical methods and accompanying software to solve challenging problems in science and engineering. The mentoring environment consisted of:

1. Weekly group meetings where research concepts were discussed, scientific literature was reviewed, and progress was monitored.
2. Pairing of students with a faculty members to develop IGA design-through-analysis methodologies.
3. Preparation of results for peer-reviewed publications.

Skycsr: Optimal Communication Methods For Coordinating Ground Support In A Private And General Aviation Setting, Jessica Burke

Industrial and Manufacturing Engineering

Delays due to miscommunication of between the pilot and ground service providers are increasing. The objective of this project is to develop a new method of communication between pilots, line service technicians and customer service agents. This will be achieved first through an investigation into current methods and state of the industry, followed by a survey conducted with a group of pilots and flight schools. This culminates in a web application that will take the deficiencies identified in the survey, to make sure ground service or fuel orders are explicitly clear and minimize the probability of a mis-fueling, overlooked fueling, …

Carbon Emission Awareness And Information Platform, Jose Ignacio Cordero, Paul Romero

Industrial and Manufacturing Engineering

Climate change due to global warming has become a worldwide concern.

Nowadays, people are starting to wake up and realize that changes need to be

made in their lifestyles in order to preserve this earth and provide a better planet

for future generations. Finding a concrete solution to global warming and climate

change has proven to be a very challenging task. Governments have tried

implementing solutions and as a result, corporations have been forced to absorb

or transfer the cost of unsuccessful environmental regulations. Meanwhile,

individuals remain frustrated, wishing they could find a way to help.

The motivation behind this …

Multi-Level Route-Optimization Computer Application, Ryan Sutardji, Frank Nguyen

Industrial and Manufacturing Engineering

This report provides a detailed analysis on how to optimize driving routes by creating a computer application. There are many different route-optimization issues that logistical companies consistently face, as well as many different solutions and algorithms. With technology on the rise, pick-up, delivery, and transportation services are become a huge part of our everyday lives. When optimizing routes, reducing transportation costs by minimizing travel distance is always ideal, but other factors must be considered such as arriving at a location before or after a certain time. Our objective is to optimize driving routes based on travel distance and priorities. We …

A Study On Flow Development In An Apu-Style Inlet And Its Effect On Centrifugal Compressor Performance, Fangyuan Lou

Open Access Dissertations

The objectives of this research were to investigate the flow development inside an APU-style inlet and its effect on centrifugal compressor performance. The motivation arises from the increased applications of gas turbine engines installed with APU-style inlets such as unmanned aerial vehicles, auxiliary power units, and helicopters. The inlet swirl distortion created from these complicated inlet systems has become a major performance and operability concern. To improve the integration between the APU-style inlet and gas turbine engines, better understanding of the flow field in the APU-style inlet and its effect on gas turbine is necessary.

A research facility for the …

Multi-Axis Machining Project Development, Ryan Patrick Blodgett, Andre Peter Rivera

Industrial and Manufacturing Engineering

Multi-axis milling is a manufacturing material removal process in which computer numerically controlled (CNC) tools cut away excess material through movement in four or more axes. Compared to traditional three-axis machining, multi-axis machining greatly increases the capability and accuracy of the CNC machining processes by reducing the amount of operations required to completely machine a part. Currently, the Industrial and Manufacturing Engineering Department at Cal Poly lacks an advanced CNC class that incorporates fourth and fifth axis CNC machining in the curriculum. This report describes the process behind creating a project for such a class. The class will demonstrate the …

Carbon-Based Hierarchical Scaffolds For Myoblast Differentiation: Synergy Between Nano-Functionalization And Alignment, Akhil Patel, Shilpaa Mukundan, Wenhu Wang, Anil K. Karumuri, Vinayak Sant, Sharmila M. Mukhopadhyay, Shilpa Sant

Mechanical and Materials Engineering Faculty Publications

While several scaffolds have been proposed for skeletal muscle regeneration, multiscale hierarchical scaffolds with the complexity of extracellular matrix (ECM) haven’t been engineered successfully. By precise control over nano- and microscale features, comprehensive understanding of the effect of multiple factors on skeletal muscle regeneration can be derived. In this study, we engineered carbon-based scaffolds with hierarchical nano- and microscale architecture with controlled physico-chemical properties. More specifically, we built multiscale hierarchy by growing carbon nanotube (CNT) carpets on two types of scaffolds, namely, interconnected microporous carbon foams and aligned carbon fiber mats. Nanostructured CNT carpets offered fine control over nano-roughness and …

Angle Of Repose, Said Shakerin

All Faculty Articles - School of Engineering and Computer Science

No abstract provided.

Associative Cad References In The Neutral Parametric Canonical Form, Daniel Robert Staves

Theses and Dissertations

Due to the multiplicity of computer-aided engineering applications present in industry today, interoperability between programs has become increasingly important. A survey conducted among top engineering companies found that 82% of respondents reported using 3 or more CAD formats during the design process. A 1999 study by the National Institute for Standards and Technology (NIST) estimated that inadequate interoperability between the OEM and its suppliers cost the US automotive industry over $1 billion per year, with the majority spent fixing data after translations. The Neutral Parametric Canonical Form (NPCF) prototype standard developed by the NSF Center for e-Design, BYU Site offers …

Solvent-Free Manufacturing Of Electrodes For Lithium-Ion Batteries, B. Ludwig, Z. Zheng, W. Shou, Y. Wang, Heng Pan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Dynamic Stall Of An Experimental Wind Turbine Blade, Matthew Scott Melius, Raúl Bayoán Cal, Karen Mulleners

Mechanical and Materials Engineering Faculty Publications and Presentations

To understand the complex flow phenomena over wind turbine blades during stall development, a scaled three-dimensional non-rotating blade model is designed to be dynamically similar to a rotating full-scale NREL 5 MW wind turbine blade. A time-resolved particle imagevelocimetry(PIV) investigation of flowbehavior during the stall cycle examines the processes of stall development and flow reattachment. Proper orthogonal decomposition (POD) and vortex detection techniques are applied to the PIV fields to quantify relevant flow characteristics such as vortex size, separation angle, and separation point throughout a dynamic pitching cycle. The behavior of the POD coefficients provides time scales for the transitional …

A Techno-Economic Analysis Of Wind Generation In Conjunction With Compressed Air Energy In The Integrated Single Electricity Market., Brendan Cleary

Doctoral

The Integrated Single Electricity Market (I-SEM) is the proposed wholesale electricity market for Ireland and it is intended to replace the current Single Electricity Market (SEM) by 2018. Subsequently, substantial modifications will be required to the SEM and this has led to significant uncertainty for stakeholders. The SEM currently features no forecast risk for renewables such as wind and there is no concept of balance responsibility. Under the I-SEM, wind generation will be exposed to forecast risk and the requirement to be balance responsible. The use of Compressed Air Energy Storage (CAES) could represent a better system configuration which would …

Semiconductor Film Grown On A Circular Substrate: Predictive Modeling Of Lattice-Misfit Stresses, Ephraim Suhir, Johann Nicolics, G. Khatibi, M. Lederer

Mechanical and Materials Engineering Faculty Publications and Presentations

effective and physically meaningful analytical predictive model is developed for the evaluation the lattice-misfit stresses (LMS) in a semiconductor film grown on a circular substrate (wafer). The two-dimensional (plane-stress) theory-of-elasticity approximation (TEA) is employed in the analysis. The addressed stresses include the interfacial shearing stress, responsible for the occurrence and growth of dislocations, as well as for possible delaminations and the cohesive strength of a buffering material, if any. Normal radial and circumferential (tangential) stresses acting in the film cross-sections and responsible for its short- and long-term strength (fracture toughness) are also addressed. The analysis is geared to the GaN …

Neutral Parametric Database, Server, Logic Layers, And Clients To Facilitate Multi-Engineersynchronous Heterogeneous Cad, Kelly Eric Bowman

Theses and Dissertations

Engineering companies are sociotechnical systems in which engineers, designers, analysts, etc. use an array of software tools to follow prescribed product-development processes. The purpose of these amalgamated systems is to develop new products as quickly as possible while maintaining quality and meeting customer and market demands. Researchers at Brigham Young University have shortened engineering design cycle times through the development and use of multiengineer synchronous (MES) CAD tools. Other research teams have shortened design cycle-times by extending seamless interoperability across heterogeneous design tools and domains. Seamless multi-engineer synchronous heterogeneous (MESH) CAD environments is the focus of this dissertation. An architecture …

In Vitro Molecular Modification Of Human Cultured And Primary Cells Using Lance Array Nanoinjection, John W. Sessions

Theses and Dissertations

Fundamentally altering cellular function at a genetic level is a major area of interest in the biologic sciences and the medical community. By engineering transfectable constructs that can be inserted to dysfunctional cellular systems, scientists can mitigate aberrant genetic behavior to produce proper molecular function. While viral vectors have been a mainstay in the past, there are many limitations, particularly related to safety, that have changed the focus of genome editing to incorporate alternative methods for gene delivery. Lance Array Nanoinjection (LAN), a second-generation microfabricated transfection biotechnology, is one of these alternative technologies. LAN works by utilizing both simultaneous electrostatic …

An Automated Method For Optimizing Compressor Blade Tuning, Kurt Berlin Hinkle

Theses and Dissertations

Because blades in jet engine compressors are subject to dynamic loads based on the engine's speed, it is essential that the blades are properly "tuned" to avoid resonance at those frequencies to ensure safe operation of the engine. The tuning process can be time consuming for designers because there are many parameters controlling the geometry of the blade and, therefore, its resonance frequencies. Humans cannot easily optimize design spaces consisting of multiple variables, but optimization algorithms can effectively optimize a design space with any number of design variables. Automated blade tuning can reduce design time while increasing the fidelity and …

Maximizing Virtual Mucax Engineering Design Team Performance, Brett Randall Stone

Theses and Dissertations

Teams of design engineers are increasingly working as members of virtual teams, or teams whose members are distributed geographically and communicate mostly through electronic means. In addition, emerging multi-user (MU) applications engage complementary teams in synchronous design activities. These new MU tools are changing the way engineers work together. Together, these factors have created a new and interesting environment in which engineering design teams must function. The work presented here lays out two major themes that teams and their managers can effectively apply to organizing and managing MU teams: 1) teams can maximize their potential productivity by determining the optimal …

Understanding And Addressing Collaboration Challenges For The Effective Use Of Multi-User Cad, David James French

Theses and Dissertations

Multi-user computer-aided design (CAD) is an emerging technology that promises to facilitate collaboration, enhance product quality, and reduce product development lead times by allowing multiple engineers to work on the same design at the same time. The BYU site of the NSF Center for e-Design has developed advanced multi-user CAD prototypes that have demonstrated the feasibility and value of this technology. Despite the possibilities that this software opens up for enhanced collaboration, there are now a new variety of challenges and opportunities to understand and address. For multi-user CAD to be used effectively in a modern engineering environment, it is …

Decomposition Of Manufacturing Processes For Multi-User Tool Path Planning, Andrew Scherbel Priddis

Theses and Dissertations

Engineering activities by nature are collaborative endeavors. Single-user applications like CAD, CAE, and CAM force a strictly serial design process, which ultimately lengthens time to market. New multi-user applications such as NXConnect address the issue during the design stage of the product development process by enabling users to work in parallel. Multi-user collaborative tool path planning software addresses the same serial limitations in tool path planning, thereby decreasing cost and increasing the quality of manufacturing processes. As part complexity increases, lead times are magnified by serial workflows. Multi-user tool path planning can shorten the process planning time. But, to be …

Analytical And Experimental Investigation Of Microstructural Alterations In Bearing Steel In Rolling Contact Fatigue, Sina Mobasher Moghaddam

Open Access Dissertations

Rolling Contact Fatigue (RCF) is one the most common failure modes in bearings. RCF is usually associated with particular microstructural alterations. Such alterations (i.e. white etching cracks, butterflies, etc.) which lead to RCF failure are known to be among the most concerning matters to bearing industry.

In the current work, an analytical as well as experimental approaches are used to investigate “butterfly wing” formation, crack initiation and propagation from inclusions. A new damage evolution equation coupled with a FE model is employed to account for the effect of mean stresses and alternating stresses simultaneously to investigate butterfly formation. The proposed …

Analytical Investigation Of Fretting Wear With Special Emphasis On Stress Based Models, Arnab Jyoti Ghosh

Open Access Dissertations

Fretting refers to the minute oscillatory motion between two surfaces in contact under an applied normal load. It can cause either surface or subsurface initiated failure resulting in either fatigue or wear or both. Two distinct regimes – partial slip and gross slip are typically observed in fretting contacts. Due to the nature of contact, various factors such as wear debris, oxidation, surface roughness, humidity etc. effect failures caused due to fretting. A number of different techniques have been developed to quantify fretting damage and several numerical models are proposed to predict damage due to fretting. Fretting wear also depends …

2016 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2016.

Predicted Stresses In Ball-Grid-Array (Bga) And Column-Grid-Array (Cga) Interconnections In A Mirror-Like Package Design, Ephraim Suhir, Reza Ghaffarian, Johann Nicolics

Mechanical and Materials Engineering Faculty Publications and Presentations

There is an obvious incentive for using bow-free (temperature change insensitive) assemblies in various areas of engineering, including electron device and electronic packaging fields. The induced stresses in a bow-free assembly could be, however, rather high, considerably higher than in an assembly, whose bow is not restricted. The simplest and trivial case of a bow-free assembly is a tri-component body, in which the inner component is sandwiched between two identical outer components (“mirror” structure), is addressed in our analysis, and a simple and physically meaningful analytical stress model is suggested. It is concluded that if acceptable stresses (below yield stress …

Development Of High-Order PN Models For Radiative Heat Transfer In Special Geometries And Boundary Conditions, Wenjun Ge, Michael F. Modest, Somesh Roy

Mechanical Engineering Faculty Research and Publications

The high-order spherical harmonics () method for 2-D Cartesian domains is extracted from the 3-D formulation. The number of equations and intensity coefficients reduces to (N+1)2/4 in the 2-D Cartesian formulation compared with N(N+1)/2 for the general 3-D formulation. The Marshak boundary conditions are extended to solve problems with nonblack and mixed diffuse-specular surfaces. Additional boundary conditions for specified radiative wall flux, for symmetry/specular reflection boundaries have also been developed. The mathematical details of the formulations and their implementation in the OpenFOAM finite volume based CFD software platform are presented. The accuracy and computational cost of the 2-D Cartesian are …

An Analysis Of The Effectiveness Of A Multi-Disciplinary Decision Support System On System-Level Decision Making, Troy Mario Seletos

Theses and Dissertations

Decisions Support Systems (DSSs) are used to enhance decision maker speed and effectiveness. However, without a view of an entire system, any decision may have unanticipated effects such as sub-optimal outcomes. The purpose of this research is to show that with a system-level analysis, more informed decisions can be made that take into account a larger system or greater number of dimensions or objectives. This research also explores the benefits of using a DSS over analysis of unprocessed data and the effectiveness of integrating a product design generator (PDG) with a business DSS, creating a system DSS, where system-level effects …