Mechanical Engineering Commons^™

Comparative Analysis Of Efficiency And Operating Characteristics Of Automotive Powertrain Architectures Through Chassis Dynamometer Testing, Jeremy J. Anderson

Dissertations, Master's Theses and Master's Reports - Open

The thesis "COMPARATIVE ANALYSIS OF EFFICIENCY AND OPERATING CHARACTERISTICS OF AUTOMOTIVE POWERTRAIN ARCHITECTURES THROUGH CHASSIS DYNAMOMETER TESTING" was completed through a collaborative partnership between Michigan Technological University and Argonne National Laboratory under a contractual agreement titled "Advanced Vehicle Characterization at Argonne National Laboratory". The goal of this project was to investigate, understand and document the performance and operational strategy of several modern passenger vehicles of various architectures. The vehicles were chosen to represent several popular engine and transmission architectures and were instrumented to allow for data collection to facilitate comparative analysis. In order to ensure repeatability and reliability during testing, …

Interactive Effect Of Fixed Time Order Strategies Within A Supply Chain On Actual In-Stock Probabilities, Mangesh S. Chaudhari

Dissertations, Master's Theses and Master's Reports - Open

This report mainly deals with the interactive effect of different in-stock probabilities used by every individual in a supply chain. Based on a simulation for 10,000 weeks, the effects of varying in-stock probabilities are observed. Based on these observations, an individual in a supply chain can take counter measures in order to avoid stock out chances hence maintaining profits.

Development Of An In Situ Measurement Device For Obtaining Material Thermal Properties, Mark A. Hepokoski

Dissertations, Master's Theses and Master's Reports - Open

This thesis presents a methodology for measuring thermal properties in situ, with a special focus on obtaining properties of layered stack-ups commonly used in armored vehicle components. The technique involves attaching a thermal source to the surface of a component, measuring the heat flux transferred between the source and the component, and measuring the surface temperature response. The material properties of the component can subsequently be determined from measurement of the transient heat flux and temperature response at the surface alone. Experiments involving multilayered specimens show that the surface temperature response to a sinusoidal heat flux forcing function is also …

Realization Of A Dc Microgrid Using A Hamiltonian Based Controls Solution, Matthew J. Heath

Dissertations, Master's Theses and Master's Reports - Open

Future power grids are envisioned to be serviced by heterogeneous arrangements of renewable energy sources. Due to their stochastic nature, energy storage distribution and management are pivotal in realizing microgrids serviced heavily by renewable energy assets. Identifying the required response characteristics to meet the operational requirements of a power grid are of great importance and must be illuminated in order to discern optimal hardware topologies. Hamiltonian Surface Shaping and Power Flow Control (HSSPFC) presents the tools to identify such characteristics. By using energy storage as actuation within the closed loop controller, the response requirements may be identified while providing a …

Nebraska Summary: S952 New Holland T5.95, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S946 New Holland T4.95, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S919 Challenger Mt475d, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2073: Case Ih Steiger 500 Quadtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2061: Challenger Mt755d, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Carbon Dioxide Absorption And Channelling In Closed Circuit Rebreather Scrubbers, Shona Cunningham

Theses

Closed Circuit Rebreathers (CCRs) are a type of Self Contained Underwater Breathing Apparatus (SCUBA) used predominantly by the diving community. CCR technologies have become prevalent within the commercial, military and technical diving communities over recent years. CCRs work by recycling breathing gas, by-passing the gas through a carbon dioxide (CO₂) chemical scrubber and topping the resultant scrubbed gas up with pure oxygen to maintain the oxygen content at a level which supports life. One of the main dangers currently faced by divers using this equipment is the risk of CO₂ poisoning if the scrubber fails. This failure …

Application Of Nano-Imprint Lithography For Next Generation Carbon Nanotube-Based Devices, Svitlana Fialkova

Dissertations

This research report addresses the development of 3D carbon nanostructures that can provide unique capabilities for manufacturing carbon nanotube (CNT) electronic components, electrochemical probes, biosensors and tissue scaffolds. The shaped CNT arrays were grown on patterned catalytic substrate by chemical vapor deposition (CVD) method. The new fabrication process for catalyst patterning based on combination of nano-imprint lithography (NIL), magnetron sputtering and reactive etching techniques was proposed and studied. The optimal process parameters for each technique were evaluated. The catalyst was made by deposition of Fe and Co nanoparticles over alumina support layer on Si/SiO₂ substrate. The metal particles were …

Fatigue Characterization Of Fire Resistant Syntactic Foam Core Material, Mohammad Mynul Hossain

Dissertations

Eco-Core is a fire resistant material for sandwich structural application; it was developed at NC A&T State University. The Eco-Core is made of very small volume of phenolic resin and large volume of flyash by a syntactic process. The process development, static mechanical and fracture, fire and toxicity safety and water absorption properties and the design of sandwich structural panels with Eco-Core was established and published in the literature. One of the important properties is needed for application in transportation vehicles is the fatigue performance under different stress states. Fatigue data are not available even for general syntactic foams. The …

Enhanced Pvdf Film For Multi Energy Harvesting, Ranmunige Nadeeka Karunarathna

Electronic Theses and Dissertations

No abstract provided.

Mode And Implementation Of A Hybrid Control System For A 2-Mode Hybrid Electric Vehicle, Zhenhua Zhu

Graduate Theses, Dissertations, and Problem Reports (ETD)

Automotive transportation consumes more than 71% of the world's total petroleum energy. The vehicle will have to use less because it will take less than 30 years to consume the rest of the proven conventional oil reservoir if the fuel consumption keeps the current trend. One of the methods to improve the vehicle efficiency is to develop Hybrid Electric Vehicle (HEV). An HEV combines an internal combustion engine (ICE) and electric motor(s) powered by batteries or capacitors to achieve better fuel economy. Among the HEVs, 2-Mode HEV combines an ICE and two electric motors with two planetary gear sets and …

A Study On The Cleaning And Modification Of Metal Surfaces By Direct Current Cathodic Electrolytic Plasma Process, Jiandong Liang

LSU Doctoral Dissertations

The processes of surface treatments or surface modifications, more formally known as surface engineering, tailor the surfaces of engineering materials. The treatments are usually intended to change physical properties such as thermal or electrical conductivity, modify the surface dimensions, i.e. roughness, etc. A novel surface treatment method, Electrolytic Plasma Process (EPP), was developed for coating purposes, in its early developmental stage. In this work, the major effort is to avoid using any environmental hazardous chemical (coatings) and to extend such its application to some new fields. The general response of the substrate material under electrolytic plasma process was summarized including …

Graph Rigidity-Based Formation Control Of Planar Multi-Agent Systems, Xiaoyu Cai

LSU Doctoral Dissertations

A multi-agent system is a network of interacting "agents" that collectively perform a complex task. This dissertation is concerned with the decentralized formation control of multi-agent systems moving in the plane. The formation problem is defined as designing control inputs for the agents so that they form and maintain a pre-defined, planar geometric shape. The focus is on three related problems with increasing level of complexity: formation acquisition, formation maneuvering, and target interception. Three different "dynamic" models, also with increasing level of complexity, are considered for the motion of the agents: the single-integrator model, the double-integrator model, and the full …

Molecular Dynamics Simulation Studies Of Interaction Of Amphiphilic Molecules With Lipid Bilayers, Jieqiong Lin

LSU Doctoral Dissertations

We use molecular dynamics simulations to investigate the behavior of various amphiphilic molecules in aqueous solutions in the presence of vitamin E or lipid bilayers. Our research studies focus on two molecular systems. First, we investigate the effect of DMSO on structural properties of DMPC bilayers and calculate bilayers permeability coefficients for both water and DMSO molecules at low DMSO concentration. The simulations show that the increase of DMSO concentration in solution leads to an increase of the permeability of water through the bilayers. The permeability increase might explain the unusual ability of DMSO, even at relatively low concentrations, to …

A Fluorescent Oil Detection Device, Yuxuan Zhou

LSU Doctoral Dissertations

On April 20th 2010, the largest offshore oil spill in U.S. history happened in the Gulf of Mexico. It is estimated total more than 4 million barrels oil spilled to Gulf of Mexico. More than two million gallons had been used. This had made the threat to coastal and sea ecosystem even greater and long term. Real-time monitoring is also a critical topic for oil spill response. In-situ monitoring devices are needed for rapid collection of real-time data. A new generation of instruments for spilled oil detection is reported in this paper. The main hypothesis in this research is that …

Development Of `Lick And Stick' Passive Wireless Temperature Sensor For Harsh Environment, Hasanul Karim

Open Access Theses & Dissertations

Wireless passive temperature sensors have been receiving increasing attention due to the ever-growing need of higher energy efficient and precise monitoring of temperatures in high temperature energy conversion systems such as gas turbines and coal-based power plants. Unfortunately, the harsh environment such as high temperature and corrosive atmosphere present in these systems has significantly limited the reliability and increased the cost of current solutions. Therefore, this research project presents the concept and design of a low cost, passive, and wireless temperature sensor that can withstand high temperature and harsh environment. The temperature sensor was designed following the principle of metamaterials …

Nanocomposite And Mechanically Alloyed Reactive Materials As Energetic Additives In Chemical Oxygen Generators, Marco Antonio Machado

Open Access Theses & Dissertations

Chemical oxygen generators are widely used for aircraft, spacecraft, submarines, and mine rescue. Oxygen-generating compositions typically include alkali metal chlorate or perchlorate that decomposes at increased temperatures, a transition-metal oxide as a decomposition catalyst, and a metal fuel that reacts with part of the produced oxygen to provide heat for a self-sustained propagation of the decomposition/combustion wave. To increase the oxygen yield per unit mass, it is of interest to minimize the amount of metal fuel, but decreasing its content leads to pulsating combustion and undesired fluctuations of the oxygen flow rate. This work explores the feasibility of replacing iron …

Process Study And Control Of Electron Beam Melting Technology Using Infrared Thermography, Jorge Mireles

Open Access Theses & Dissertations

An IR camera was installed in an Arcam A2 system (Arcam AB, Mölndal, Sweeden) and layer-by-layer image acquisition was achieved. The camera's capability to detect manufacturing defects was evaluated by implementing computer vision techniques using LabVIEW measurement and programming software (National Instruments, Austin, TX). Thermal maps acquired by the IR camera allowed layer-by-layer part temperature to be recorded. A core objective of this research was to study the impact of processing temperature on EBM-fabricated Ti-6Al-4V parts and achieve controlled mechanical properties. In this research, build variations were achieved by modifying parameters that change processing temperature from the standard processing temperature. …

Experimental Study On The Fabrication Of Advanced Materials For Energy Applications Using High Energy Mechanical Milling, Ashvin Kumar Narayana Swamy

Open Access Theses & Dissertations

The reaction of aluminum (Al) powder with water has the potential for on demand hydrogen generation. Conventional Al powders, however, react with water slowly due to a highly protective oxide layer on the particle surface. Current methods for Al activation involve harmful and expensive materials. The nano-scale Al powders also remain very expensive and have problems such as a large amount of oxide on the surface. The use of aluminum in an energy generation cycle is also hindered by the fact that, although Al is the most abundant metal in the Earth's crust, its recovery from ore consumes a lot …

The Development Of Self-Supported Electromechanical Structures Using Fused Deposition Modeling, Jorge Ramos-Almeida

Open Access Theses & Dissertations

Recent research has focused on the fabrication freedom of 3D printing to create not only conceptual models but also final end-use products. In the last decade, several research groups have reported embedding electronic components and electrical interconnects into 3D printed structures during process interruptions; however, to date there is an absence of fabricated devices with electromechanical functionality for parts fabricated in a single Additive Manufacturing (AM) build sequence.

The focus of this research is the use of Fused Deposition Modeling (FDM) to manufacture a self-supported electromechanical motor. FDM is an AM process capable of building parts in a layer-by-layer fashion. …

Effect Of Hafnium-Incorporation On The Microstructure And Dielectric Properties Of Cobalt Ferrite Ceramics, Stephen Josiah Wells

Open Access Theses & Dissertations

The effect of hafnium ion (Hf⁴⁺) incorporation in cobalt ferrite (CFO) was studied. Samples of Hf substituted CFO ceramic (CoFe_2-xHf_xO₄), were synthesized in the laboratory with hafnium concentrations ranging from x=0.000 to x=0.200. X-ray diffraction scans show that the Hafnium CFO crystalizes in the inverse spinel phase. Inclusion of hafnium causes lattice expansion, increasing the lattice parameter from 8.374 í? for pure CoFe2O4 to 8.391 í? for the highest concentration of hafnium tested (x=0.020). The dielectric properties of CFO are greatly enhanced by inclusion of hafnium. The enhancement is due to the …

Thermal Barrier Coatings (Tbc's) For High Heat Flux Thrust Chambers, Christopher Michael Bradley

Open Access Theses & Dissertations

The last 30 years materials engineers have been under continual pressure to develop materials with a greater temperature potential or to produce configurations that can be effectively cooled or otherwise protected at elevated temperature conditions. Turbines and thrust chambers produce some of the harshest service conditions for materials which lead to the challenges engineers face in order to increase the efficiencies of current technologies due to the energy crisis that the world is facing. The key tasks for the future of gas turbines are to increase overall efficiencies to meet energy demands of a growing world population and reduce the …

A Block Operator Splitting Method For Heterogeneous Multiscale Poroelasticity, Paul M. Delgado

Open Access Theses & Dissertations

Traditional models of poroelastic deformation in porous media assume relatively homogeneous material properties such that macroscopic constitutive relations lead to accurate results. Many realistic applications involve heterogeneous material properties whose oscillatory nature require multiscale methods to balance accuracy and efficiency in computation.

The current study develops a multiscale method for poroelastic deformation based on a fixed point iteration based operator splitting method and a heterogeneous multiscale method using finite volume and direct stiffness methods. To characterize the convergence

of the operator splitting method, we use a numerical root finding algorithm to determine a threshold surface in a non-dimensional parameter space …

Development And Testing Of An Ignition Physics Test Facility And An Oxygen/Methane Swirl Torch Igniter, Jesus Roberto Flores

Open Access Theses & Dissertations

There are many advantages to LOX/methane propulsion, such as in-situ resource utilization from Mars and the Moon, and simplicity of ground operations due to its non-toxic nature. There exists a lack of fundamental understanding of the ignition physics, and flame characteristics of these propellants when related to rocket propulsion, which has created undesirably long design cycles and flight hardware that is not optimized. Motivated by these issues, a study of the ignition physics of a shear coaxial injector is proposed, in which the flow field dynamics and ignition transients will be observed through a visually accessible combustion chamber. The main …

Pressure And Heat Flux Effects On The Heat Transfer Characteristics Of Liquid Methane, Chance Paul Garcia

Open Access Theses & Dissertations

The heat transfer effects on liquid methane are investigated with the use of a carbo-thermal rig at the Center for Space Exploration Technology Research (cSETR) located at the University of Texas at El Paso (UTEP). The cSETR carbo-thermal rig design approach is presented along with the design of a methane condensing mobile unit (MCMU) to supply the laboratory and rig with liquid methane. The proposed research will generate useful insight in to heat transfer coefficient behavior, non-dimensional correlations, different flow conditions, varied inlet conditions, and varied heat flux for a subscale test article applicable to a regenerative cooled rocket engine …

A Damage-Trap Interfacial Design To Improve Impact Resistance Of Polymers, Md Shariful Islam

Open Access Theses & Dissertations

Polymer materials such as Polycarbonate (PC), Polymethyl methacrylate (PMMA) have numerous applications in transparent armor which includes body and face shield, helmet, windows of the armored vehicle etc. The most challenging part of these applications is to ensure the safety of the people. These materials are often subjected to impact loading, so it is important to study the failure of these materials under impact loading. An experimental study has been made to investigate the impact damage in transparent layered materials. Impact experiments were carried out on various monolithic specimens and layered specimens for both two types of materials at different …

New Topics On Nanoindentation Of Polymers And Composite Materials, Ricardo Martinez-Hernandez

Open Access Theses & Dissertations

In this study, nanoindentation was used to determine Young's modulus of homogeneous plastic materials as well as inhomogeneous epoxy woven fabric composites using various indenters. In the first part, homogeneous PMMA and polycarbonate were characterized using conical and spherical indenters. The conventional approach of the inverse analysis was modified in order to account for effects obtained during spherical nanoindentation. The experimental results were verified using FEA analysis in ABAQUS. It was found that viscous effects were present in conical nanoindentations which led to an overestimation of contact stiffness. The second part, the response of carbon and glass fiber woven fabric …