Mechanical Engineering Commons^™

Perspectives On Quality Coordination And Assurance In Global Supply Chains, Ling Li, John N. Warfield

Information Technology & Decision Sciences Faculty Publications

The 2007 recall of Berko Electric Toe-Space Heaters made in the US, the recall of backpack blowers made in Japan, the recalls of toys and pet food produced in China have exposed the potential of global supply chain disruptions. This product recall storm leads to the issue of quality assurance in global supply chain management. Product recalls indicate that manufacturing companies are particularly vulnerable to ensure quality when they source via a global supply chain with poor visibility. Obviously, a supply chain cannot afford this kind of sourcing and supply structure that threatens the supply-chain integrity. This special issue on …

Quasi-Steady Capillarity-Driven Flows In Slender Containers With Interior Edges, Mark M. Weislogel, J. Alex Baker, Ryan M. Jenson

Mechanical and Materials Engineering Faculty Publications and Presentations

In the absence of significant body forces the passive manipulation of fluid interfacial flows is naturally achieved by control of the specific geometry and wetting properties of the system. Numerous 'microfluidic' systems on Earth and 'macrofluidic' systems aboard spacecraft routinely exploit such methods and the term ‘capillary fluidics’ is used to describe both length-scale limits. In this work a collection of analytic solutions is offered for passive and weakly forced flows where a bulk capillary liquid is slowly drained or supplied by a faster capillary flow along at least one interior edge of the container. The solutions are enabled by …

Numerical Study Of Drop Formation From Dripping To Jetting, Allouah Kadjo

Mechanical and Aerospace Engineering Theses - Archive

The formation of liquid droplet from a capillary tube has been examined using numerical simulations. The dimensions of the capillary tube and the flow velocity have been varied to observe the regimes of drop formation. There are three main regimes of drop formation, which are the periodic dripping, the dripping faucet and the jetting regimes. The mechanism of drop formation changes from one regime to another and involves different parameters. A particular emphasis has been placed on the velocity limits between the different regimes and the critical role played by instabilities in the generation of satellite drops. The algorithm used …

Numerical Modeling Of A Parallel Plate Electrowetting-On-Dielectric (Ewod) Device, Kevin Tully

Mechanical and Aerospace Engineering Theses - Archive

Numerical modeling and simulations have been performed in this study that focuses on modeling the fluid dynamics of an Electrowetting-on-Dielectric (EWOD) device. The case to be modeled in the present study is a droplet cutting problem where a droplet is sandwiched between two plates of Teflon and an electrical actuation will cause the droplet to cut or split into two smaller droplets. A finite difference method has been used to solve the Navier-Stokes equations, along with the continuity equation. An algorithm used for tracking the free surface is the Volume of Fluid (VOF) method. Along with using the VOF method …

Safe Power Vermont: A Look Into The Campaign To Retire The Vermont Yankee Nuclear Power Station., Dylan M. Kreis

Capstone Collection

This case study provides an in-depth look into the campaign to retire an aging nuclear power plant located in the southeast corner of Vermont. The Vermont Yankee Nuclear Power Station (VY) began commercial operations in 1972 under a forty year operating license issued by the Nuclear Regulatory Commission (NRC). Opposition to the plant’s existence has been unwavering and has increased in intensity since the sale of the plant in 2002. The Vermont Yankee Nuclear Power Corporation (VYNPC), a consortium of local and regional utilities, sold VY to an out-of-state corporation owner known as Entergy. The company was quick to apply …

Modeling Of Thermal Properties Of Fiber Glass Polyester Resin Composite Under Thermal Degradation Condition, Marvin S. Tsoi

Electronic Theses and Dissertations

Composites, though used in a variety of applications from chairs and office supplies to structures of U.S. Navy ships and aircrafts, are not all designed to hold up to extreme heat flux and high temperature. Fiber-reinforced polymeric composites (FRPC) have been proven to provide the much needed physical and mechanical properties under fire exposure. FRPC notable features are its combination of high specific tensile strength, low weight, along with good corrosion and fatigue resistance. However FRPC are susceptible to thermal degradation and decomposition, which yields flammable gas, and are thus highly combustible. This property restricts polymeric material usage. This study …

Ultra-Abrupt Tapered Fiber Mach-Zehnder Interferometer Sensors, B. Li, J. Lan, W. Sumei, L. Zhou, Hai Xiao, Hai-Lung Tsai

Electrical and Computer Engineering Faculty Research & Creative Works

A fiber inline Mach-Zehnder interferometer (MZI) consisting of ultra-abrupt fiber tapers was fabricated through a new fusion-splicing method. By fusion-splicing, the taper diameter-length ratio is around 1:1, which is much greater than those (1:10) made by stretching. The proposed fabrication method is very low cost, 1/20-1/50 of those of LPFG pair MZI sensors. The fabricated MZIs are applied to measure refractive index, temperature and rotation angle changes. The temperature sensitivity of the MZI at a length of 30 mm is 0.061 nm/°C from 30-350 °C. The proposed MZI is also used to measure rotation angles ranging from 0° to 0.55°; …

Implicit Methods For Efficient Musculoskeletal Simulation And Optimal Control, Antonie J. Van Den Bogert, Dimitra Blana, Dieter Heinrich

Mechanical Engineering Faculty Publications

The ordinary differential equations for musculoskeletal dynamics are often numerically stiff and highly nonlinear. Consequently, simulations require small time steps, and optimal control problems are slow to solve and have poor convergence. In this paper, we present an implicit formulation of musculoskeletal dynamics, which leads to new numerical methods for simulation and optimal control, with the expectation that we can mitigate some of these problems. A first order Rosenbrock method was developed for solving forward dynamic problems using the implicit formulation. It was used to perform real-time dynamic simulation of a complex shoulder arm system with extreme dynamic stiffness. Simulations …

Heat Transfer In Triangular Ducts With Axial Conduction,Containing Porous Medium, Abhishek Banerjee

Mechanical and Aerospace Engineering Theses - Archive

The objective of this study is to find a numerical solution for the velocity and temperature field in a duct of triangular cross-section area. A fully saturated porous medium is considered to be present in the duct. The study reports the contribution of axial conduction in heat transfer to flow passing through triangular porous passages. The terms in x-direction are retained in the energy equation due to the presence of axial conduction. Also, because of the geometrical asymmetry, non-orthogonal boundary conditions can exist and thus make the determination of heat transfer more difficult. The problem under consideration uses H2 boundary …

Nonlinear Finite Element Analysis Of Columns, Rajkiran Muppavarapu

Mechanical and Aerospace Engineering Theses - Archive

In many engineering applications structural components are considered to be beams or columns subjected to a range of external loads such as dead weight, wind, temperature changes etc.In this work a mathematical model has been developed for a sports lighting tower considering it to be a cantilever beam with large deformation. The concept of non-linear P-Delta analysis is applied to the column. Using this model, a tower analysis tool was developed in MATLAB. Using this tool various design alternatives can be examined to evaluate their suitability to a particular task.A number of example problems from the available literature were solved …

Stable Reference Trajectory Modification For Handling Actuator Failure In Control Systems, Ifeolu Olalekan Ogunleye

Mechanical and Aerospace Engineering Theses - Archive

The issue of rapidly reconfiguring the reference trajectory under unanticipated actuator failures in order to regain lost performance or aircraft handling qualities is explored. The failures detected in real-time are compensated for by ensuring the input to the system reflects current system conditions. This thesis will also show that only the general structure of the failed system component is needed to achieve successful failure detection and reference trajectory reconfiguration. This approach allows the nominal control structure to remain unchanged in the presence of change flight and system conditions. Acceptable system performance is recovered by detecting the actuator failures in real-time. …

Vibrational Analysis Of Soloflex Whole Body Vibration Platform, Zachary Croatt, Josh Robers

The Journal of Undergraduate Research

A Soloflex Whole Body Vibration (WBV) Platform was tested for its frequency and magnitude of vibration at multiple settings on the supplied dial. An accelerometer was used to measure the vibrations on different points mapped across the platform. The motor attached to the board was also tested for its frequency using a high-speed camera. The amplitude measurements found from the accelerometer data was compared to the readings on the supplied control module to “calibrate” the platform for medical testing.

Vibrational Analysis Of An Electromechanical Toothbrush, Mark Wager

The Journal of Undergraduate Research

The effectiveness of an electromechanical toothbrush is based entirely on its ability to remove plaque through vibrations. This paper contests that the three-dimensional motion of more inexpensive models of electromechanical toothbrushes can be accurately modeled in one-dimension so as to predict the motion of future toothbrush designs using simply the material properties, motor specifications, and grip design. Vibrational modeling, mathematical modeling, and experimentation were used in the analysis to confirm the outcome of the study and the assumptions of the model.

Viability Of A Controllable Chaotic Micromixer Through The Use Of Titanium-Nickel Shape Memory Alloy, David Ryan Lilly

Theses and Dissertations--Mechanical and Aerospace Engineering

Microfluidic devices have found applications in a number of areas, such as medical analysis, chemical synthesis, biological study, and drug delivery. Because of the small channel dimensions used in these systems, most microchannels exhibit laminar flow due to their low Reynold’s number, making mixing of fluids very challenging. Mixing at this size scale is diffusion-limited, so inducing chaotic flow patterns can increase the interface surface area between two fluids, thereby decreasing overall mixing time.

One method to create a chaotic flow within the channel is through the introduction of internal protrusions into the channel. In such an application protrusions that …

Measurements In Air-Water Bubbly Flow Through A Vertical Narrow High-Aspect Ratio Channel, Benjamin R. Patrick

Electronic Theses and Dissertations

Two-Phase bubbly flows are encountered in a wide range of industrial applications, particularly where phase changes occur as seen in high performance heat exchangers and boiling reactors for power generation. These flows have been extensively studied in channels with circular geometries using air-water flows, though little data exists for flows through narrow rectangular channels. Measurements in thin geometries are particularly challenging since large bubbles bridge the gap, and it is difficult to compare point measurements with photographic techniques. The objective of this study is to explore the abilities of hot-film anemometry and high speed photography for taking measurements in a …

Heat Transfer In A Coupled Impingement-Effusion Cooling System, Mark W. Miller

Electronic Theses and Dissertations

Gas turbine engines are prevalent in the today’s aviation and power generation industries. The majority of commercial aircraft use a turbofan gas turbine engines. Gas turbines used for power generation can achieve thermodynamic efficiencies as high as 60% when coupled with a steam turbine as part of a combined cycle. The success of gas turbines is a direct result of a half century’s development of the technology necessary to create such efficient, powerful, and reliable machines. One key area of technical advancement is the turbine cooling system. In short, increasing the turbine inlet temperature leads to a rise in cycle …

Purge And Secondary Flow Interaction Control By Means Of Platform Circumferential Contouring, Melissa Harris

Electronic Theses and Dissertations

This study presents an attempt to reduce the losses produced by the purge flow in a turbine stage by incorporating circumferential platform contouring. Two contours are proposed and compared against a baseline at different levels of swirl. The computational simulations were performed using a RANS three-dimensional Computational Fluid Dynamics code with the Shear Stress Transport turbulence model. The results of steady simulations demonstrate that for the first contour, when the flow is swirled to 50% of the rim speed, the purge flow exits the cavity with less cross flow. This in turn reduces the strength of the passage vortex. However, …

Heat Transfer Study Of A Triple Row Impingement Channel At Large Impingement Heights, Roberto Claretti

HIM 1990-2015

Advanced cooling techniques are required to increase the Brayton cycle temperature ratio necessary for the increase of the overall cycle's efficiency. Current turbine components are cooled with an array of internal cooling channels in the midchord section of the blade, pin fin arrays at the trailing edge and impingement channels in the leading edge. Impingement channels provide the designer with high convective coefficients on the target surface. Increasing the heat transfer coefficient of these channels has been a subject of research for the past 20 years. In the current study, a triple row impingement channel is studied with a jet …

Effect Of Rib Aspect Ratio On Heat Transfer And Friction In Rectangular Channels, Lucky Vo Tran

HIM 1990-2015

The heat transfer and friction augmentation in the fully developed portion of a 2:1 aspect ratio rectangular channel with orthogonal ribs at channel Reynolds numbers of 20,000, 30,000, and 40,000 is studied both experimentally and computationally. Ribs are applied to the two opposite wide walls. The rib aspect ratio is varied systematically at 1, 3, and 5, with a constant rib height and constant rib pitch (rib-pitch-to-rib-height ratio of 10). The purpose of the study is to extend the knowledge of the performance of rectangular channels with ribs to include high aspect ratio ribs. The experimental investigation is performed using …

Nebraska Summary: S814 New Holland T7.200, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S812 New Holland T7.170, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S796 Massey Ferguson 5475, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1983: Bobcat Ct450, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1996: Case Ih Magnum 225 T3, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2002a: John Deere 8260r My12, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2015: New Holland T9.560, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1996b: New Holland T7070, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

On The Thermodynamics Of Degradation, Mehdi Amir Darehbidi

LSU Doctoral Dissertations

All materials when subjected to fatigue loading are prone to failure if the number of cycles exceeds a certain level. Prediction of the number of cycles to failure is, therefore, of utmost importance in nearly all engineering applications. The existing methods for evaluating the fatigue life are tedious, expensive, and extremely time consuming as fatigue often takes many thousands to millions of cycles until failure occurs. Therefore, methods that can readily estimate the number of cycles to failure are highly desirable. In this work, innovative solutions to fatigue problems are presented and their practical significance is discussed. The premise of …

Creep Behaviour Of Hand Laminated Glass Reinforced Polymer Composites., Brian Quinn

Theses

The creep behaviour of hand laminated, glass fiber reinforced polyester composites were studied at coupon level, due to the use of similar materials in long term load bearing civil and structural engineering applications. Creep predictions were made by fitting the parameters of several viscoelastic models to experimental creep data as well as two accelerated test methods, time temperature superposition (TTS) and frequency time transformations (FTT). TTS experiments were carried out in a dynamic mechanical analyzer (DMA) in three point bending mode for three types of material systems. Creep compliance master curves representing the linear viscoelastic creep response at reference temperatures …

An Advanced Controller For A Semi-Active Wheelchair Suspension, David J. Smith

Master's Theses

An Advanced Controller for a Semi-Active Wheelchair Suspension was designed, built and tested.  The suspension consisted of a Goodyear 1S3-011 air spring, IQ Valves high speed proportional solenoid valve, and a custom made accumulator.  Several controller designs specific to semi-active suspensions were designed and tested.  The controllers investigated were skyhook, acceleration driven damping, and a combined control law employing both a dual and single sensor version.  The implementation of skyhook control suffered performance degradation from the idealization due to particular elements of hardware, however acceleration driven damping showed a marked and statistically significant improvement over skyhook control, in hardware, by …