Mechanical Engineering Commons^™

Effect Of Piezoelectric Actuation On Curved Beams And Single Lap Joints, Calicia Johnson

LSU Master's Theses

Piezoelectric materials have seen a significant usage increase over the past decade. They have been found to be effective as either sensors or actuators in smart structure applications, which allows them to act more as an adaptive system rather than a passive system. Piezoelectric materials are very effective transducers which convert mechanical energy into electrical energy, known as the direct piezoelectric effect or they have the ability to convert electrical energy to mechanical energy, known as the converse piezoelectric effect. The absence of additional mechanical parts, its lightweight and high strength to weight ratio is what make piezoelectric materials so …

The Design And Modification Of A Sputter System For Dc Reactive Sputtering Of Alumina And Zirconia Thin Films, Diane Van Ho

LSU Master's Theses

Yttria-stabilized zirconia (7% YSZ) is the most used material for thermal barrier coatings (TBCs) to reduce the conductive heat transfer on turbine blades, but it is not resistant to infrared radiation. In order to reduce radiation heat transfer, alternating materials, such as alumina and zirconia, can be used to fabricate multi-layer coatings in which each layer is optimized to reflect a targeted range of wavelength. This research aims to fabricate these multi-layer coatings by reactive magnetron sputtering. Reactive magnetron sputtering is the sputtering of an elemental target in the presence of a reactive gas that will react with the target …

Two-Stage Biaxial Thermomechanical Cycle Of Shape Memory Polymer Based Syntactic Foam, Abraham Michael King

LSU Master's Theses

A shape memory polymer (SMP) is a polymeric material that exhibits shape memory behavior. It can be “programmed” to take on a desired shape and “recovered” to revert back to its original shape. This ability to remember multiple shapes and switch between them with the application of a stimulus from an outside source is very desirable in certain applications. By dispersing glass microspheres in a SMP matrix, a syntactic foam is created that retains much of the shape memory capabilities but has higher strength and lower density than the pure SMP. These characteristics make this material a good candidate for …

Pool Boiling Enhancement Via Micro Ratchets, Lance Austin Brumfield

LSU Master's Theses

Nucleate boiling is an attractive method for achieving high heat flux at low superheat temperatures. It is frequently used for industrial applications such as heat exchangers and is being considered to cool advanced central processing units (CPU) which produce heat fluxes on the order of 1 MW/m2 and are becoming increasing less efficient to cool via forced conduction of air. The issues with implementing nucleate boiling as a cooling mechanism lies in the difficulty of quantifying the complex and numerous mechanisms which control the process. A comprehensive nucleate boiling model has yet to be formulated and will required in order …

Gas Turbine Blade Tip And Near Tip Heat Transfer With Film Cooling, Gregory Kramer

LSU Master's Theses

Gas turbine blade tips experience very high thermal loads due to high temperature combustion gases and tip leakage flows. This leads to the tip region being very susceptible to experiencing failures. To better understand these effects, experiments were performed in a suction-type low speed wind tunnel cascade to determine heat transfer coefficients and film cooling effectiveness distributions on a highly-loaded 2-D gas turbine blade model in the tip and near-tip regions. The blade shape was generated to match the pressure coefficients of the operating turbine blade design. The model featured multiple tip and pressure side film cooling holes and a …

Design, Fabrication And Characterization Of A New Wind Tunnel Facility – Linear Cascade With A Wake Simulator, Jean-Philippe Junca-Laplace

LSU Master's Theses

A new wind tunnel has been designed and constructed at the LSU Mechanical Engineering Laboratories. The objective was to design a versatile test facility, suitable for a wide range of experimental measurements on turbine blades. The future study will investigate the impact of unsteady inflow conditions on film cooling performance. More specifically, it will study how the unsteady flow due to the upstream passing wakes coming from the front row vane affects the film cooling performances on the turbine blades. The test section consists of a four passage linear cascade composed of three full blades and two shaped wall blades. …

Testing And Characterization Of Second-Order Differential Microphones, Joshua H. Merlis

Graduate Dissertations and Theses

The focus of this thesis is the testing and characterizing of directional microphones, designed based on the ear of the fly Ormia ochracea. The response of these microphones is modeled as a linear combination of the gradients of the sound field. A least squares approach is employed in order to determine the transfer functions between the response and these gradients. Knowledge of these complex transfer functions is crucial in understanding the nature and quality of the response of these microphones.

Once determined, these transfer functions are used to simulate the plane wave response of differential microphones. This process is invaluable …

The Integrated Wrf/Urban Modeling System: Development, Evaluation, And Applications To Urban Environmental Problems, Fei Chen, Hiroyuki Kusaka, Robert Bornstein, Jason Ching, C.S.B. Grimmond, Susanne Grossman-Clarke, Thomas Loridan, Kevin W. Manning, Alberto Martilli, Shiguang Miao, David J. Sailor, Francisco P. Salamanca, Haider Taha, Mukul Tewari, Xuemei Wang, Andrzej A. Wyszogrodzki, Chaolin Zhang

Mechanical and Materials Engineering Faculty Publications and Presentations

To bridge the gaps between traditional mesoscale modeling and microscale modeling, the National Center for Atmospheric Research (NCAR), in collaboration with other agencies and research groups, has developed an integrated urban modeling system coupled to the Weather Research and Forecasting (WRF) model as a community tool to address urban environmental issues. The core of this WRF/urban modeling system consists of: 1) three methods with different degrees of freedom to parameterize urban surface processes, ranging from a simple bulk parameterization to a sophisticated multi-layer urban canopy model with an indoor outdoor exchange sub-model that directly interacts with the atmospheric boundary layer, …

Test 1999a: John Deere 8335rt My12, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Mechanical Characterizations Of Environmentally Conditioned Shape Memory Polymers For Reconfigurable Aerospace Structures, Jared T. Fulcher

University of Kentucky Master's Theses

Shape memory polymers (SMPs) have been candidate materials for morphing applications. However, the SMPs have not been fully tested to work in relevant environments required for Air Force missions. In this study, an epoxy-based SMP was separately exposed to moisture, lubricating oil and UV radiation, which are simulated service environments designed to be reflective of anticipated performance requirements. The thermomechanical properties and shape memory effects were studied by using novel high-temperature nanoindentation technique. Results show that environmental conditions have affected the glass transition temperature and mechanical properties of the SMPs. In most cases, the conditioned SMPs exhibited higher elastic moduli …

Development Of Measurement Methods For Testing Of Hydrokinetic Devices To Evaluate The Environmental Effect On Local Substrate, Michael Volpe

Honors Theses

Modifications and upgrades to the hydraulic flume facility in the Environmental Fluid Mechanics and Hydraulics Laboratory (EFM&H) at Bucknell University are described. These changes enable small-scale testing of model marine hydrokinetic(MHK) devices. The design of the experimental platform provides a controlled environment for testing of model MHK devices to determine their effect on localsubstrate. Specifically, the effects being studied are scour and erosion around a cylindrical support structure and deposition of sediment downstream from the device.

Performance Characteristics Of Airlift Pumps With Vortex Induced By Tangential Fluid Injection, Jacob Riglin

Honors Theses

The effect of the swirl component of air injection on the performance of an airlift pump was examined experimentally. An airlift pump is a device that pumps a liquid or slurry using only gas injection. In this study, the liquid used was water and the injected gas was air. The effect of the air swirl was determined by measuring the water discharge from an airlift pump with an air injection nozzle in which the air flow had both axial and tangential components and then repeating the tests with a nozzle with only axial injection. The induced water flow was measured …

Design Of A Liquid Fuel Injector For Alternative Fuel Studies In An Atmospheric Model Gas Turbine Combustor, John Stevenson

Honors Theses

A new liquid-fuel injector was designed for use in the atmospheric-pressure, model gas turbine combustor in Bucknell University’s Combustion Research Laboratory during alternative fuel testing. The current liquid-fuel injector requires a higher-than-desired pressure drop and volumetric flow rate to provide proper atomization of liquid fuels. An air-blast atomizer type of fuel injector was chosen and an experiment utilizing water as the working fluid was performed on a variable-geometry prototype. Visualization of the spray pattern was achieved through photography and the pressure drop was measured as a function of the required operating parameters. Experimental correlations were used to estimate droplet sizes …

Analytical Investigation Of Squeeze Film Dampers, Mehmet Murat Altuğ Biҫak

Dissertations, Master's Theses and Master's Reports - Open

Squeeze film damping effects naturally occur if structures are subjected to loading situations such that a very thin film of fluid is trapped within structural joints, interfaces, etc. An accurate estimate of squeeze film effects is important to predict the performance of dynamic structures.

Starting from linear Reynolds equation which governs the fluid behavior coupled with structure domain which is modeled by Kirchhoff plate equation, the effects of nondimensional parameters on the damped natural frequencies are presented using boundary characteristic orthogonal functions. For this purpose, the nondimensional coupled partial differential equations are obtained using Rayleigh-Ritz method and the weak formulation, …

Control Design And Genetic Algorithm Optimization For Electrostatic Mems, Jill C. Blecke

Dissertations, Master's Theses and Master's Reports - Open

This dissertation discusses structural-electrostatic modeling techniques, genetic algorithm based optimization and control design for electrostatic micro devices.

First, an alternative modeling technique, the interpolated force model, for electrostatic micro devices is discussed. The method provides improved computational efficiency relative to a benchmark model, as well as improved accuracy for irregular electrode configurations relative to a common approximate model, the parallel plate approximation model. For the configuration most similar to two parallel plates, expected to be the best case scenario for the approximate model, both the parallel plate approximation model and the interpolated force model maintained less than 2.2% error in …

Length Of The Annular Regime For Condensing Flows Inside A Horizontal Channel - The Experimental Determination Of Its Values And Its Trends, Patcharapol Gorgitrattanagul

Dissertations, Master's Theses and Master's Reports - Open

The experiments observe and measure the length of the annular regime in fully condensing quasi-steady (steady-in-the-mean) flows of pure FC-72 vapor in a horizontal condenser (rectangular cross-section of 2 mm height, 15 mm width, and 1 m length). The sides and top of the duct are made of clear plastic that allows flow visualization. The experimental system in which this condenser is used is able to control and achieve different quasi-steady mass flow rates, inlet pressures, and wall cooling conditions (by adjustment of the temperature and flow rate of the cooling water flowing underneath the condensing-plate). The reported correlations and …

Estimating Industrial Building Energy Savings Using Inverse Simulation, Franc Server, J. Kelly Kissock, Dan Brown, Steve Mulqueen

Mechanical and Aerospace Engineering Faculty Publications

Estimating energy savings from retrofitting existing building systems is traditionally a time intensive process, accomplished by developing a detailed building simulation model, running the model with actual weather data, calibrating the model to actual energy use data, modifying the model to include the proposed changes, then running the base and proposed models with typical weather data to estimate typical energy savings. This paper describes a less time-intensive method of estimating energy savings in industrial buildings using actual monthly energy consumption and weather data. The method begins by developing a multivariate three-parameter changepoint regression model of facility energy use. Next, the …

Estimation Of The Centre Of Mass From Motion Capture And Force Plate Recordings: A Study On The Elderly, Sebastien Cotton, Michele Vanoncini, Philippe Fraisse, Nacim Ramdani, Emel Demircan, Andrew P. Murray, Thierry Keller

Mechanical and Aerospace Engineering Faculty Publications

The estimation of the centre of mass position in humans is usually based on biomechanical models developed from anthropometric tables. This method can potentially introduce errors in studies involving elderly people, since the ageing process is typically associated with a modification of the distribution of the body mass. In this paper, an alternative technique is proposed, and evaluated with an experimental study on 9 elderly volunteers. The technique is based on a virtual chain, identified from experimental data and locating the subject's centre of mass. Its configuration defines the location of the centre of mass, and is a function of …

Computational Investigation Of Particle Settling Effects On Inhaled Submicron Bioaerosol Deposition In The Human Lung, Mohammed Ali, Essam A. Ibrahim

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 1-5

Dynamic Modeling And Parameter Estimation For Impact Analysis And Robust Packaging Design, Thomas M. Stone, Seung-Kyum Choi, Hemanth Amarchinta

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 6-13

Asme Early Career Technical Journal (Front Matter), Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. -x

Motion Tracking Through Machine Vision, Poonam Savsani, Vimal Savsani

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 14-21

Significance Of Mwcnt And Tio2 Nanofillers On Low-Density Polyethylene Thermal & Mechanical Properties: Applicability For Pipes Used In Water & Energy Systems, Erin E. Mcdonald, Gail D. Jefferson, Andrew J. Whelton, Tinh Nguyen

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 22-26

Asme Early Career Technical Journal (Complete Issue), Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Blast Response Of Sandwich Composite Structural Panels, Teseswi P. Tadepalli, P Raju Mantena

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 33-38

Evaluation Of The Effect Of Simplified And Patient-Specific Arterial Geometry On Hemodynamic Flow In Stenosed Carotid Bifurcation Arteries, Rodward L. Hewlin Jr, John P. Kizito

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 39-44

Evaluation Of Pulse Jet Mixing Using A Scalar Quantity And Shear Stress, Ibraheem R. Muhammad, John P. Kizito

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 45-52

Manufacturing Knowledge Sharing: The Utilization Of Knowledge Base Technologies In Plm, Abdul Shakoor, Arshad Mehmood, Khizar Azamand Riaz Akber Sayyed

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 53-59

Optimal Liquid Film Thickness Of An Evaporating Film Down An Inclined Plane For Maximum Heat Flux In Spray Cooling Applications, Richard Opoku, John P. Kizito

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 68-72

Multidisciplinary Design Optimization Of Aerospace Vehicle: Single Engine Rotorcraft, Adeel Khalid

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 60-67