Mechanical Engineering Commons^™

An Investigation Of The Characteristics Of Regenerative Heat Exchangers, Timothy J. Murphy

Theses and Dissertations

The objective of the current research was to investigate the effects of reducing screen thickness on the volume and compactness factor of stacked, wire-screen regenerators. An improved transient step-change method was devised which integrated experimental data with a numerical model of the flow to determine the heat transfer coefficient and friction factor. The improvements to the approach are: (1) the measured inlet temperature trace is used, (2) the heat transfer coefficient is based on a parameter called the sponge effect delay time, and (3) the important effect of the tube surrounding the matrix is included in the numerical model. The …

Structures And Techniques For Implementing And Packaging Complex, Large Scale Microelectromechanical Systems Using Foundry Fabrication Processes, John H. Comtois

Theses and Dissertations

Microelectromechanical Systems, or 'MEMS' is a broad new field of research into devices that range in size from a few microns to a few millimeters. Much of the technology supporting MEMS research is borrowed from the microelectronics industry; so MEMS holds out the promise of batch fabrication of microminiaturized machines that can be easily integrated with electronics. This dissertation research investigated structures and methods for implementing and packaging complex, large scale microelectromechanical devices and systems using commercially available foundry fabrication processes. It specifies methods for creating and packaging large, complex MEM systems, allowing the exploration of new MEMS architectures at …

Experimental And Analytical Investigation Of Waterjet Cleaning Process, Ping Meng

Dissertations

This doctoral dissertation is concerned with the development of water based cleaning technology required by industry which may substitute the traditional approach based upon the use of various chemical cleansers.

The experimental study involves the waterjet removal of various coatings (rust, oil and epoxy based paints, etc.). Cleaning was carried out under a wide range of operational and geometrical conditions (standoff distance, travel speed, water pressure, diameters of sapphire nozzle and focusing tube, nozzle body type). A new designed spiral nozzle body was tested in this work. The use of surfactant was also investigated. Microscope and SEM surface were used …

Experimental And Numerical Investigation Of Abrasive Waterjet Polishing Technology, Fenggang Li

Dissertations

The objective of this investigation is the development of the abrasive waterjet (AWJ) based polishing technology. The result of the investigation will assist the implementation of AWJ polishing for manufacturing processes and procedures.

Experimental exploration of AWl polishing involving processing of difficultmachine materials such as Alumina ceramic and stainless steel. Surface improvement due to this processing is evaluated by measuring the roughness of the generated surfaces and examining the microhardness and micro-topography of the surfaces using Scanning Electronic Microscopy (SEM). The surface roughness of 0.3 micron was obtained at samples of ceramic and metal alloys at a reasonable rate using …

Global Fuzzy Control Based On Cell Mapping, Tea-Quin Kim

Dissertations

Cell mapping methods can generate global optimal controls for nonlinear dynamic systems. However, the implementation of this approach for on-line control is difficult due to its use of a table-based controller which requires a large amount of memory.

In this dissertation, a cell mapping based systematic method is developed to construct a fuzzy controller to replace the table-based controller for global optimal control of dynamic systems. The method consists of four steps: 1) An optimal control table is generated using a cell mapping algorithm. 2) The cells are linked into trajectories to characterize the optimal dynamic evolution of various cell. …

Reduction Of Inertia-Induced Forces In A General Spatial Mechanism, Sahidur Rahman

Dissertations

A computer-aided design procedure has been developed for minimizing the adverse effects of the inertia-induced forces by optimum mass redistribution amongst the links of high speed general spatial linkages. The evaluation of an optimality criterion for the mass redistribution of the mechanism will be carried out with the aid of a quadratic programming technique. This has been found to be successful in minimizing inertia induced forces and torques. The validity of the optimization procedure will be demonstrated by application to one kind of spatial linkage.

No literature has been found on the balancing of a general spatial mechanism, since its …

Relay Ladder Logic And Petri Nets For Discrete Event Control Design : A Comparative Study, Edward Twiss

Theses

In the 1960's and earlier discrete event systems (DES) were controlled by hardwired electromechanical relay systems. In 1969 an electronic programmable logic controller (PLC) was introduced. PLC's have been programmed utilizing relay ladder logic (RLL). RLL is a graphical programming language with software "devices" used to emulate electromechanical devices. RLL programs, however, often become large and difficult to understand because its graphical representation of physical switching devices obscures the discrete event dynamics inherent in the process to be controlled. Petri nets are a methodology for modeling discrete event systems (DES). Using a Petri net based controller, a control strategy could …

Granular Dynamics Study Of Sieving, Heng Yung

Theses

The objective of this thesis is to study the behaviors of granular particles under sieving. A three-dimensional dynamic simulation code was transferred and modified for this purpose, The major concern is the mass flow rate of the particles. Lots of case studies were run. The influences of the friction coefficient, the sieve aperture, and the energy of vibration are studied.

Measured Impacts Of Air Conditioner Condenser Shading, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

A study has been conducted by the Florida Solar Energy Center (FSEC) to examine if space cooling energy savings can be achieved from shading of residential air conditioning (AC) condenser units. The investigation consisted of before-and-after experiments conducted on three homes over a two year period. A recent EPA study recommends shading of exterior AC condensers, using landscaping or other means, as a method to reduce space cooling energy use (Akbari et al., 1992).

Monitored Energy Use Patterns In Low-Income Housing In A Hot And Humid Climate, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The Florida Solar Energy Center (FSEC) is metering energy use in two Habitat for Humanity developments. The objective is to understand how energy is used in low income housing and how it can be effectively reduced. The ten "control homes" come from a conventional housing project built by in 1993 Habitat for Humanity in Homestead, Florida. Another ten "experimental homes" have been recruited from the 190 home Jordan Commons development in the same vicinity. These houses, which are soon to be metered, are designed to be energy efficient with high SEER air conditioners, reflective roofing, solar water heaters and energy …

Side-By-Side Testing Of Commercial Office Lighting Systems: Two-Lamp Fluorescent Fixtures, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Lighting systems in commercial office buildings are primary determinants of building energy use. In warmer climates, lighting energy use has important implications for building cooling loads as well as those directly associated with illumination tasks. To research the comparative performance of conventional and advanced office lighting systems, Florida Solar Energy Center (FSEC) set up the Lighting Flexible Test Facility (LFTF) which allows side-by-side comparison of lighting options in two otherwise identical 2.7 m x 3.7 m (9' x 12') south facing offices.

The ceiling of the LFTF contains 0.61 m x 1.2 m (2' x 4') recessed fluorescent fixtures designed …

Measured Performance Of Energy-Efficient Computer Systems, Florida Solar Energy Center, David Floyd

FSEC Energy Research Center®

The intent of this study is to explore the potential performance of both Energy Star computers/printers and add-on control devices individually, and their expected savings if collectively applied in a typical office building in a hot and humid climate. Recent surveys have shown that the use of personal computer systems in commercial office buildings is expanding rapidly. The energy consumption of such a growing end-use also has a significant impact on the total building power demand. In warmer climates, office equipment energy use has important implications for building cooling loads as well as those directly associated with computing tasks. Recently, …

Optimization Of Torquer Coil Design For Use With The Small Satellite Attitude Control Simulator, David Deloyd Anderson

Undergraduate Honors Capstone Projects

This paper presents a procedure used to optimize the performance of a ferromagnetic core magnetic torquer coil design for use on the Space Dynamics Laboratory (Logan, UT) Small Satellite Attitude Control Simulator. The items of optimization include the primary goal of maximizing the coil 's magnetic moment while reducing power consumption and system mass within given power, mass, and dimensional constraints. The optimization process makes use of several simple equations to determine a few starting points for design, after which an iterative approach based on experimentation is used to produce the final design. It is found that optimal magnetic moment …

Daylighting Dimming And Energy Savings: The Effects Of Window Orientation And Blinds, Florida Solar Energy Center, Lynn Schrum

FSEC Energy Research Center®

The Daylighting Test Facility (DTF) located at Florida Solar Energy Center, was used to study daylight dimming systems and how orientation and blinds effect energy savings. To evaluate the impact of blinds on dimming savings, the energy consumption was compared in two pairs of offices for all four window orientations: north, south, east and west. One office in each pair had blinds in a fixed position (down and open) and the other office had no blinds. From September through December of 1994, data were collected on the north- and south-facing offices. The DTF was rotated 90 degrees and data were …

Applying Photovoltaics To Disaster Relief, Florida Solar Energy Center, William Young

FSEC Energy Research Center®

Hurricanes, floods, tornadoes, earthquakes, and other disasters can happen at any time, often with little or no advance warning. They can be as destructive as Hurricane Andrew leaving several hundred-thousand people homeless or as minor as an afternoon thunderstorm knocking down local power lines to your home. Major disasters leave many people without adequate medical services, portable water, electrical service and communications. In response to a natural disaster, photovoltaic (solar electric) modules offer a source of quite, safe, pollution-free electrical power. Photovoltaic (PV) power systems are capable of providing the electrical needs for vaccine refrigerators, microscopes, medical equipment, lighting, radios, …

Coupling And Attenuation Of Waves In Plates By Randomly Distributed Attached Impedances, Joseph A. Turner, Richard L. Weaver

Department of Engineering Mechanics: Faculty Publications

The average response of an infinite thin plate with statistically homogeneous attached random impedances is examined. The added impedances, which represent typical heterogeneities that might occur on complex shells, provide light coupling between the extensional, shear, and flexural waves. The mean plate response is formulated in terms of the Dyson equation which is solved within the assumptions of the first-order smoothing approximation, or Keller approximation, valid when the heterogeneities are weak. Scattering attenuations are derived for each propagation mode. It is shown that the attenuation of one wave type due to coupling to another is proportional to the modal density …

Droplet Evaporation And Deformations In An Amplitude Modulated Ultrasonic Field, Nihad E. Daidzic, Rene Stadler, Adrian Melling

Aviation Department Publications

The aim of the report presented is the measurements of droplet oscillations.

Grain-Boundary Structure Effects On Intergranular Stress Corrosion Cracking Of Alloy X-750, Brent L. Adams, Ted Olsen, N. Panayotou, Y. Pan

Faculty Publications

This work was supported by the Department of Energy under Grant No. DE-FG02-88ER 45355. TO was supported by the National Science Foundation during her 1993-94 stay at the Institute for Advanced Studies (Princeton) under grant DMS-9304580. The authors wish to acknowledge helpful discussion with Carol Nichols, John Hack, Gino Palumbo, Karl Aust, and Gary Was. It is well known that the properties and behavior of grain boundaries are strongly affected by local chemistry and atomic structure. This paper focuses on the mesoscale description of grain boundary structure (i.e. the five crystallographic degrees of freedom) and correlations with intergranular stress corrosion …

Study Of Periodic Gust Loads On Airfoils, Tatsuya Nakajima

Masters Theses

The wings on aircraft can experience unsteady loads due to atmospheric disturbances; e.g., wind, the wakes of other aircraft, structural vibrations, or some combination of these sources. In some cases flow unsteadiness can be beneficial by augmenting the lift and reducing the drag; under different circumstances temporal variations in the flow can induce stall or cause structural failure.

In this study, the response of isolated (and tandem) NACA 0012 airfoil(s) to time-periodic unsteadiness have been investigated. The sources of unsteadiness include a time-varying free stream flow angle, a time varying free stream velocity magnitude, and an oscillating airfoil.

The predicted …

A Study Of Kanban Based Production System In Cellular Manufacturing Environment, Sanjay Bhargava

Masters Theses

The study of effects of production data variabilities on Kanban based cellular manufacturing system is vital before its design and implementation because it would give better understanding of their uncertain behavior.

In this research, a detailed analysis of a Kanban system, with subcell scenario, under dynamic operating conditions is performed. The Control variables considered were number of Kanbans, processing time variability, demand variability and machine breakdown. The performance parameters considered were profit, production lead time, machine utilization and material processing lead time.

Approximately 200 simulation runs were made with 3 replications each by varying one control variable at a time. …

Development Of A Simple, Analytical Method To Optimize Machining Cycles For Non-Cnc Gear Hobbing Machines, Steven M. Klabunde

Graduate Research Papers

The purpose of this research project was to develop a simple, analytical method for the optimization of hobbing cycles on non-CNC gear hobbing machines. Such a method would allow manufacturers to optimize hobbing cycle times, reduce part costs, and improve productivity. There have been many advances in gear cutting tool technology. Because of these advances, the capabilities of modern cutting tools are beyond the capabilities of non-CNC machines designed more than fifteen years ago. The majority of the machines used today in gear manufacturing are of this vintage. The cycles on these machine tools are machine-limited, which is much more …

The Progressive Failure Analysis Of Cut Slope In Anisotropic Strain Softening Soils, Jong Woon Choi

Civil & Environmental Engineering Theses & Dissertations

The failure phenomena in earth structures such as slopes and embankments on clay foundations are a consequence of the formation of failure surfaces.

A finite difference computer code, FLAC (Itasca Consulting Group, 1993), with the isotropic Mohr-Coulomb plasticity model, is used to analyze the undrained progressive failure of a strain softening soil during a slope excavation process. The focus of the study is on the short-term stability of slopes. In the first series of analyses, which are aimed at the evaluation of anisotropic strength effect on slope stability, the isotropic Mohr-Coulomb plasticity model is slightly modified to implement the anisotropic …

A One-Dimensional Model For Storm Breaching Of Barrier Islands, Cheol Shik Shin

Civil & Environmental Engineering Theses & Dissertations

A set of numerical models is developed for simulating the four stages of barrier breaching characterized by one horizontal spatial dimension.

The SBEACH model is employed for the first stage of dune/beach erosion. The Lax-Wendroff two-step explicit scheme for Stage II is developed to simulate initiation of ocean flood propagation on initially dry barrier islands and the method of characteristics (MOC), is employed to compute additional boundary data. The development of the Preissmann implicit scheme for water motion and a forward time centered space explicit scheme for sediment motion in Stages III and IV provide a tool to study the …

Exact Solutions For Orthogonal And Non-Orthogonal Magnetohydrodynamic Stagnation-Point Flow, Shahrooz Moosavizadeh

Mathematics & Statistics Theses & Dissertations

The viscous plane flow of an electrically conducting fluid towards an infinite wall is solved in the presence of a magnetic field which is aligned with the flow far from the wall. The problem has two dimensionless parameters-- ε, the magnetic Prandtl number, and β, the square of the ratio of Alfven velocity to fluid velocity far from the wall. The problem has a similarity solution which reduces the governing equations to a system of coupled ordinary differential equations which can be solved numerically. For extreme values of ε, both large and small, singular perturbation techniques are used to derive …

Variational Methods In Sensitivity Analysis And Optimization For Aerodynamic Applications, Adem Ibrahim Hussen

Mechanical & Aerospace Engineering Theses & Dissertations

Variational methods (VM) sensitivity analysis, which is the continuous alternative to the discrete sensitivity analysis, is employed to derive the costate (adjoint) equations, the transversality conditions, and the functional sensitivity derivatives. In the derivation of the sensitivity equations, the variational methods use the generalized calculus of variations, in which the variable boundary is considered as the design function. The converged solution of the state equations together with the converged solution of the costate equations are integrated along the domain boundary to uniquely determine the functional sensitivity derivatives with respect to the design function.

The determination of the sensitivity derivatives of …

Sensitivity Analysis And Optimization Of Aerodynamic Configurations With Blend Surfaces, Almuttil Mathew Thomas

Mechanical & Aerospace Engineering Theses & Dissertations

A novel (geometrical) parametrization procedure using solutions to a suitably chosen fourth order partial differential equation is used to define a class of airplane configurations. Inclusive in this definition are surface grids, volume grids, and grid sensitivity. The general airplane configuration has wing, fuselage, vertical tail and horizontal tail. The design variables are incorporated into the boundary conditions, and the solution is expressed as a Fourier series. The fuselage has circular cross section, and the radius is an algebraic function of four design parameters and an independent computational variable. Volume grids are obtained through an application of the Control Point …

Unsteady, Transonic Flow Around Delta Wings Undergoing Coupled And Natural Modes Response: A Multidisciplinary Problem, Margaret Anne Menzies

Mechanical & Aerospace Engineering Theses & Dissertations

The unsteady, three-dimensional Navier-Stokes equations coupled with the Euler equations of rigid-body dynamics are sequentially solved to simulate and analyze the aerodynamic response of a high angle of attack delta wing undergoing oscillatory motion. The governing equations of fluid flow and dynamics of the multidisciplinary problem are solved using a time-accurate solution of the laminar, unsteady, compressible, full Navier-Stokes equations with the implicit, upwind, Roe flux-difference splitting, finite-volume scheme and a four-state Runge-Kutta scheme, respectively. The primary model under consideration consists of a 65° swept, sharp-edged, cropped delta wing of zero thickness at 20° angle of attack. In a freestream …

An Approach For Multidisciplinary Design Optimization, Robert V. Krueger

Mechanical & Aerospace Engineering Theses & Dissertations

Multidisciplinary Design Optimization (MDO) is an optimization technique that allows complex designs to be improved by managing conflicting goals in such a fashion so as to improve the overall design. This thesis presents a nonhierarchic MDO formulation and gives a general explanation of how it is to be applied to various appropriate problems. In addition, this thesis evaluates the viability of this MDO technique by applying it to two distinct, multidisciplinary problems that have been used as examples in other literature. The first example problem is a combined aerodynamic/structural problem and the second example is an alkylation process problem. First, …

Uncontrolled Air Flow In Non-Residential Buildings, Florida Solar Energy Center, James Cummings

FSEC Energy Research Center®

The objective of this study was to develop the capability to substantially reduce energy use, building degradation and indoor air pollution caused by uncontrolled air flow in nonresidential buildings. For purposes of the study, 'uncontrolled air flow' was defined as air moving across the building envelope or between zones or components of a building, where the pathways of flow, the direction of flow, and the origin of the air are unknown, unspecified, or unintended. The study comes to three major conclusions as follows: 1. Uncontrolled air flow is pervasive in buildings, often resulting in severe -- and sometimes even catastrophic …

Towards Rational Trade Offs Between Environment And Hydro-Power, V Ranganathan

IIMB Management Review

The economic importance of hydro-power has long been recognised the world over. In fact, a certain correlation between exploitation of hydropower potential and economic growth is clearly discernible. Developed nations of North America and Western Europe, for example, have exploited 83% and 98%, respectively, of their potential hydro- power, while relatively poorer East European, Asian and African countries have a much lower record, ranging between 8% and 36% (see chart). Recent trends in hydro-power development in India are a source of serious concern: for instance, the hydro-thermal ratio of power generation in the country has been steadily declining from 1:1 …