Mechanical Engineering Commons^™

Nano Oil Additives And Their Effect On Uh-60 Auxiliary Power Unit Performance, James Patrick Folk

Theses and Dissertations

This study is designed to research the tribological properties of nano oils developed by NanoPro MT and to determine their effects on fuel consumption in an UH-60 Blackhawk Auxiliary Power Unit (APU). For this work, two different nano oils were tested and compared against the performance of conventional oil. The first nano oil mixture contains proprietary nanodiamond particles and the second nano oil contains a mix of zinc sulfide, boron nitride, and graphene particles. Aeroshell 560 was used as the conventional oil and was blended with the nano particles to create both nano oils. This oil meets the military specifications …

Studies Of Asphalt Roofing Sealant Failure For Shingle Systems Subjected To High Wind Conditions For Both Elastic And Viscoelastic Sealant Material Response, Artem Aleshin

Theses and Dissertations

It has been documented that the sealant between asphalt roof shingles may delaminate at significantly lower wind speeds than those for which they are rated, with major consequences on safety and repair costs. In perspective, developing more resilient material systems and devising more effective installation procedures are sensible strategies to mitigate this problem. A practical approach may also entail adding a second self-sealing strip. In the first portion of this thesis, the elastic structural response of an asphalt roof shingle-sealant system consisting of individual three-tab shingles, which are bonded to the underlying shingles with two sealant strips and are subjected …

Estimation Of Basic And Mission Benefit Of Condition-Based Maintenance Deployment In Hums Equipped Ah-64 Aircraft Using Nlp And Regression Analysis, Tanzina Zaman

Theses and Dissertations

Condition-based maintenance (CBM) is a maintenance practice that involves regular monitoring of the mechanical condition of components of interest, processing of information collected, and then decision-making to ensure both maximizing the time interval between repairs and minimizing the number of unscheduled failures. CBM also offers early detection of failure which can prevent major breakdowns and repairs. Vibration monitoring is one of the effective techniques for condition monitoring. Health and Usage Monitoring System (HUMS) is a powerful tool for aviation industry which monitors health status and trending data. Vibration Monitoring Unit (VMU) and Modernized Signal Processing Unit (MSPU) are two forms …

Automated Tool Selection And Tool Path Planning For Free-Form Surfaces In 3-Axis Cnc Milling Using Highly Parallel Computing Architecture, Andrey Balabokhin

Theses and Dissertations

This research presents a methodology to automatically select cutters and generate tool paths for all stages in 3-axis CNC Milling of free-form surfaces. Tools are selected and tool paths are planned in order to minimize the total machining time. A generalized cutter geometry model is used to define available cutters and an arbitrary milling surface is initially defined by a triangular mesh.

The decisions made by process engineers in selecting cutting geometry and generating tool paths for milling dramatically influence the final result. Often, the resulting tool path is non-optimal, because the engineers cannot consider all the available information. However, …

Physics Based Modeling Of Guided Waves For Detection And Characterization Of Structural Damage In Nde And Shm, Banibrata Poddar

Theses and Dissertations

Guided waves based damage detection techniques are popular for their ease of generation and detection along with their ability to travel long distances. Accurate and efficient modeling is a key for successful implementation of guided waves for NDE/SHM. However, efficient prediction of scattering from various damage is challenging due to the complex nature of these guided waves.

This dissertation presents as physics based efficient and accurate modeling techniques to predict ultrasonic wave propagation and their interaction with various damage. Detection and characterization of damage in structures can typically be divided into two categories, active and passive. This research is aimed …

Ndt And Shm Methods Of Damage Detection In Welded Structures, Saad Mohammed

Theses and Dissertations

There has been an increasing demand for Nondestructive Testing (NDT) and Structural Health Monitoring (SHM) techniques to continuously monitor during all processes of a structure to prevent catastrophic failure and reduce maintenance costs. NDT and SHM are inspection processes which form part of the quality assurance/quality control (QA/QC) scheme. Among NDT and SHM methods, ultrasonic and guided wave techniques are the most commonly and widely used in industry. Ultrasonic methods provide the advantage of accurately locating and dimensioning defects within structures. Most of these structures consist of welded joints because welding is an economical and efficient method for obtaining a …

Effects Of Process Variants On Metallurgical And Mechanical Properties In Friction Stir Welding Of Aluminum Alloys, Xiaomin Huang

Theses and Dissertations

Conventional shoulder friction stir welding (CSFSW) produces uneven heat input through welded material thickness: higher close to the top and lower close to the bottom. When CSFSW is applied on certain aluminum alloys, such as 7xxx and 2xxx series high strength aluminum alloys which contain low melting point intermetallic, overheating and local melting may happen close to weld crown. Stationary shoulder friction stir welding (SSFSW) may generate much more uniform heat input through plate thickness than CSFSW due to the non-rotating shoulder and rotating pin. Therefore, overheating and local melting are expected to be avoided in SSFSW. Furthermore, local properties …

Techno Economical Analysis Of Solid Oxide Iron-Air Redox Battery For Power Generation And Energy Storage, Farzana Yasmeen

Theses and Dissertations

The largest source of greenhouse gas emissions in the United States is from burning fossil fuels for electricity, heat, and transportation. Due to increasing environmental constraints associated with greenhouse gas emissions and uncertainty in the supply of fossil fuels, power systems of the future will become more reliable on renewable power source. To overcome the intermittency issue of renewable power, a promising cost effective electricity-storage systems is vital. The U.S. Department of Energy (DOE) has established detailed cost targets for energy storage system. One of the targets is capital cost which should be under $150/kWh for new technology. Another target …

Mechanical Characterization Of Sicf-Sicm Nuclear Fuel Cladding By A Novel Hydraulic Internal Pressurization Method, Kirill Shapovalov

Theses and Dissertations

Ceramic Matrix Composites (CMC) have been actively researched for applications requiring high temperature strength and damage tolerance. Examples are turbine engine hot section components, leading edges for hypersonic vehicles, nuclear fusion reactor first wall and blanket, and recently nuclear fuel claddings. Predictable material damage behavior is desirable for these applications so early damage accumulation can be detected before a catastrophic failure occurs. Many ceramic materials can withstand high temperature environments, but due to inherent brittleness of ceramics the high damage tolerance and the predictable damage behavior are difficult to achieve. Ceramic fiber reinforced ceramic composites (CFCC) have demonstrated the above …

In-Shoe Plantar Pressure System To Investigate Ground Reaction Force Using Android Platform, Ahmed A. Mostfa

Theses and Dissertations

Human footwear is not yet designed to optimally relieve pressure on the heel of the foot. Proper foot pressure assessment requires personal training and measurements by specialized machinery. This research aims to investigate and hypothesize about Preferred Transition Speed (PTS) and to classify the gait phase of explicit variances in walking patterns between different subjects. An in-shoe wearable pressure system using Android application was developed to investigate walking patterns and collect data on Activities of Daily Living (ADL). In-shoe circuitry used Flexi-Force A201 sensors placed at three major areas: heel contact, 1st metatarsal, and 5th metatarsal with a PIC16F688 microcontroller …

Wavelet Analysis Of Periodic Error In Heterodyne Interferometry, Chao Lu

Theses and Dissertations

Heterodyne displacement measuring interferometry provides important metrology for applications requiring high resolution and accuracy. Heterodyne Michelson interferometers use a two-frequency laser source and separate the two optical frequencies into one fixed length and one variable length path via polarization. Ideally these two beams are linearly polarized and orthogonal so that only one frequency is directed toward each path. An interference signal is obtained by recombining the light from the two paths; this results in a measurement signal at the heterodyne (split) frequency of the laser source. This measurement signal is compared to the optical reference signal. Motion in the measurement …

Bio-Inspired Design Of Mechanical Band Pass Sensor With The Ability To Scavenge Energy, Md Riaz Uddin Ahmed

Theses and Dissertations

Primary objective of this work is to introduce the multi-scale computational model for the bio-inspired acousto-ultrasonic band pass sensor that are capable of mechanically sense and/or filter wide range user defined frequencies. Selecting a particular and/or a distinct band of frequencies is essential for many applications in science engineering and technologies. For example design of sensors in chemical, biomedical and biological applications; device application for acoustic modulation by breaking the acoustic reciprocity and the sensors used in precision manufacturing applications requires sensing and/or filtering of wide range of acousto-ultrasonic frequencies. Presently, electronic devices are widely employed in commercial applications for …

A Multiphysics Modeling Of Solid Oxide Metal-Air Redox Battery, Md Ahsan Uddin

Theses and Dissertations

Cost-effective and large scale energy storage is essential for the growth of the future’s ‘‘green energy’’ infrastructure. Among the energy storage technologies currently being used, rechargeable batteries represent a class of advanced electrical energy storage (EES) mechanisms that can be valuable for the future renewable integration and smart grid. Rechargeable batteries have innumerous advantages over the conventional pumped hydro and compressed-air energy storage system. Now days, There are various types of rechargeable batteries available to work as an energy storage device in a smart grid but it still needs many breakthroughs to become commercially viable for stationary energy storage. First …

Guided Wave Based Integrated Structural Health Monitoring And Nondestructive Evaluation, Zhenhua Tian

Theses and Dissertations

Damage detection and health monitoring are critical for ensuring the structural safety in various fields, such as aerospace, civil and nuclear engineering. Structural health monitoring (SHM) performs online nondestructive evaluation (NDE) and can predict the structural remaining life through appropriate diagnosis and prognosis technologies. Among various SHM/NDE technologies, guided ultrasonic waves have shown great potential for fast and large area SHM/NDE, due to their sensitivity to small defects and capability to propagate long distances. Recent advances in guided wave based SHM/NDE technologies have demonstrated the feasibility of detecting damage in simple structures such as metallic plates and pipes. However, there …

Impact Of Constructing A Low Crested Weir In Cape Canaveral On Flushing In The Banana River, Atousa Saberi

Theses and Dissertations

The purpose of this study is to determine the extent to which constructing a low crested weir adjacent to Port Canaveral improves ushing in the Banana River. The Banana River is a 50 km long sub-basin of Indian River Lagoon (IRL), located between Cape Canaveral and Merritt Island in Brevard County. Although Port Canaveral locks connect the Banana River to the ocean, the locks remain closed when there are no passing vessels; therefore, it has limited circulation and a long ushing time. Declining water quality can be linked to recent high mortality events of di erent species living in the …

Springback Force Considerations In Compliant Haptic Interfaces, Dallin R. Swiss

Theses and Dissertations

This thesis investigates the potential benefits and challenges of using compliant mechanisms in the design of haptic interfaces. The benefits and challenges are presented with an emphasis on their inherent springback behavior and an active compensation approach. Design criteria for compliant mechanism joint candidates are reviewed and several joints are surveyed. Quantitative calculations of axial stiffness and maximum stress for five candidates are presented. Generalized analytical models of springback force and compensation torque are created to simulate the implementation of each joint candidate in a two degree-of-freedom planar pantograph. We use these models in the development and discussion of an …

Elucidating The Mechanisms Of Rate-Dependent Deformation At Ambient Temperatures In A Model Metallic Glass, Matthew Bradley Harris

Theses and Dissertations

In this work, the Shear Transformation Zone (STZ) dynamics model is adapted to capture the transitions between different regimes of flow serration in the deformation map of metallic glass. This was accomplished by scaling the STZ volume with a log-linear fit to the strain rate, and also adjusting the activation energy of an STZ with a log-linear fit to maintain constant yield strength at differing strain rates. Twelve simulations are run at each of six different strain rates ranging from 10^-5 to 10⁰ s^-1, and statistics are collected on simulation behavior and shear band nucleation and …

Effects Of Various Mobility Aids On Lower-Extremity Muscle Activity, Michael Ryan Sanders

Theses and Dissertations

Millions of people each year spend some portion of their time using mobility aids to facilitate periods of non-weight bearing ambulation. The use of these devices changes the loading conditions of the lower extremities, which may result in skeletal muscle adaptations. The purpose of this work was to evaluate the effects of 3 types of mobility aids on lower-extremity muscle activity. Evaluation was based on 1) measured muscle activation signals using electromyography (EMG), and 2) measured joint kinematics and ground reaction forces, which were used to predict muscle forces. 16 healthy subjects (7 female, 9 male), ages 18-27 participated in …

Modeling The Residual Useful Life Of Railroad Bearing Grease, Thania Alejandra Martinez

Theses and Dissertations

Railroad bearing performance is often constrained by the life of its lubricant. The lubricant life is determined by tribomechanical processes that are present during bearing operation. No known physical models exist to predict the railroad bearing lubricant life. This thesis summarizes the efforts undertaken in the development of empirical models that can accurately predict the residual useful life of railroad bearing grease. Modeling techniques to be employed include regression, regression trees, and split plots. The grease samples used to populate this model come from healthy and faulty bearings that were run under different loads, speeds, and ambient conditions in a …

Pressure Field Estimation Using Particle Image Velocimetry, Jean O. Calzada

Theses and Dissertations

In recent years, scientist and engineers have shown the advantages created by using the Particle Image Velocimetry (PIV) method as flow diagnostic tool to characterize instantaneous velocity fields. One of the important benefits is found on its non-intrusive nature, this leads to accurate velocity fields. From the velocity field obtained by PIV important quantities can be derived, such as pressure and vorticity. The present study, uses PIV data of an incompressible turbulent pulsed jet to determine the pressure field associated with the flow field. The pressure is calculated by using the averaged velocity field along with three different fundamental equation: …

Resistance Prediction For Asymmetrical Configurations Of High-Speed Catamaran Hull Forms, Srikanth Asapana

Theses and Dissertations

Predicting the resistance of a high-speed catamaran has been of interest to naval architects for the last three decades. Even though considerable amount of research has been carried out in this area, there remains a degree of uncertainty in the accurate resistance prediction of catamaran hull forms in the early design stage. Researches carried out so far have generally ignored the resistance characteristics of unconventional and unsymmetrical catamaran hull forms. This thesis attempts to undertake a comparative analysis of resistance characteristics between newly developed unconventional catamaran hull forms of different configurations derived from existing conventional NPL series of round bilge …

Aerodynamic Improvement Of The Byu Supermileage Vehicle, Sayan Dobronsky

Theses and Dissertations

The purpose of this thesis work was to design a new shape for the BYU Supermileage vehicle in order to improve its fuel efficiency. Computational Fluid Dynamics (CFD) was used to obtain the coefficient of drag (CD) and drag area of the current baseline vehicle at a Reynolds number of 1.6x10^6 and 8.7x10^5. Then a new shape was developed using mesh morphing software. The new shape was imported into the CFD program and the drag figures and airflow plots from the modified design were compared with the baseline vehicle. Scale models of the vehicles were also printed using a 3D …

Design And Manufacture Of Mesoscale Robot-Actuated Surgical Instruments, Clayton L. Grames

Theses and Dissertations

Minimally Invasive Surgery (MIS) is a growing field including both laparoscopic androbotic operations. Surgeons and engineers are making continual efforts to reduce the negative effects of procedures on patients. Reducing the size of the surgical instruments is one effective method pursued in this effort. When the instruments approach 3 mm in diameter, they reach a threshold where the entry incisions can be small enough that no scar is left on the patient. Laparoscopic instruments on this scale exist but typically lack wrist articulation and only have 1 degree of freedom (DoF). Alternatively, robotic surgical instruments can achieve high levels of …

Using Star-Ccm+ To Evaluate Multi-User Collaboration In Cfd, Kasey Johnson Webster

Theses and Dissertations

The client-server architecture of STAR-CCM+ allows multiple users to collaborate on a simulation set-up. The effectiveness of collaboration with this architecture is tested and evaluated on five models. The testing of these models is a start to finish set-up of an entire simulation excluding computational time for generating mesh and solving the solution. The different models have distinct differences which test every operation that would be used in a general CFD simulation. These tests focus on reducing the time spent preparing the geometry to be meshed, including setting up for a conformal mesh between multiple regions in conjugate heat transfer …

Design And Validation Of A Complex Loading Whole Spinal Segment Bioreactor, Amanda Marie Beatty

Theses and Dissertations

Intervertebral disc (IVD) degeneration is a prevalent health problem that is highly linked to back pain. To understand the disease and tissue response to therapies, ex-vivo whole IVD organ culture systems have recently been introduced. The goal of this study was to develop and validate a whole spinal segment culturing system that loads the disc in complex loading similar to the in-vivo condition, while preserving the adjacent endplates and vertebral bodies. The complex loading applied to the spinal segment was achieved with three pneumatic cylinders. The pneumatic cylinders were rigidly attached to two triangular alumni plates at each corner, comprising …

Novel Applications Of A Thermally Tunable Bistable Buckling Silicon-On-Insulator (Soi) Microfabricated Membrane, Robert A. Lake

Theses and Dissertations

Buckled membranes are commonly used microelectromechanical systems (MEMS) structures. Recent work has demonstrated that the deflection and stiffness of these membranes can be tuned through localized joule heating. These devices were implemented into the design and fabrication of two novel device applications, a tunable pressure sensor and a steerable micromirror. A differential pressure across the membrane causes de reflection, up or down, which can be measured and related to a specific pressure. By tuning the stiffness of the membrane, its pressure response is varied providing a wider range of application for the pressure sensor. A 2.0mm by 2.0mm square membrane …

An Approach For Designing Origami-Adapted Products With Aerospace Mechanism Examples, Jessica Morgan

Theses and Dissertations

The objective of this research is to develop a design process for origami-adapted products and demonstrate it using aerospace mechanism examples. Origami-adapted design is a type of origami-based design. Origami-based design ranges from abstract to concrete applications of origami to design and includes: origami-inspired design, origami-adapted design, and origami-applied design. Origami-adapted design adapts origami fold patterns into products while preserving functionality. Some of the desirable attributes of origami that are sought after in design include: 1) reduced number of parts, 2) stowability, 3) deployability, 4) transportability, 5) manufacturability from a flat sheet of material, 6) ease of miniaturization, 7) a …

Reactive Motions In A Fully Autonomous Crs Catalyst 5 Robotic Arm Based On Rgbd Data, Arad Haselirad

Theses and Dissertations

This study proposes a method to perform velocity estimation using motion blur in a single image frame along x and y axes in the camera coordinate system and intercept a moving object with a robotic arm. It will be shown that velocity estimation in a single image frame improves the system's performance. The majority of previous studies in this area require at least two image frames to measure the target's velocity. In addition, they mostly employ specialized equipments which are able to generate high torques and accelerations.

The setup consists of a 5 degree of freedom robotic arm and a …

Neutral Parametric Canonical Form For 2d And 3d Wireframe Cad Geometry, Robert Steven Freeman

Theses and Dissertations

The challenge of interoperability is to retain model integrity when different software applications exchange and interpret model data. Transferring CAD data between heterogeneous CAD systems is a challenge because of differences in feature representation. A study by the National Institute for Standards and Technology (NIST) performed in 1999 made a conservative estimate that inadequate interoperability in the automotive industry costs them $1 billion per year. One critical part of eliminating the high costs due to poor interoperability is a neutral format between heterogeneous CAD systems. An effective neutral CAD format should include a current-state data store, be associative, include the …

Improving The Suction Performance And Stability Of An Inducer With An Integrated Inlet Cover Bleed System Known As A Stability Control Device, Ryan K. Lundgreen

Theses and Dissertations

The performance of an inducer with the integration of an inlet cover bleed system known as a stability control device (SCD) is investigated using computational fluid dynamics. Inducers are the first stage of high suction performance pumps and are designed to operate under cavitating conditions. Improvements in design have allowed inducers to operate stably with low inlet head conditions, however, cavitation instabilities ultimately lead to pump failure. It has been shown that inducers that employ an SCD fully suppress cavitation instabilities.The performance of an inducer is explored at both on- and off-design flow coefficients, where the flow coefficient is a …