Mechanical Engineering Commons^™

Wheelie King Trainer And Controller, Michael C. Uytingco, Paul E. Hubner, Dmitriy Petrovykh

Mechanical Engineering

The ``wheelie'' is a popular, classic bicycle trick which novice bicyclists often attempt as an introduction to advanced bike tricks. However, many are hesitant to try due to the risks and safety hazards associated with performing one. The purpose of this project is to create an on-board system which will assist a user in maintaining a wheelie after achieving the required position while incorporating safety mechanisms to prevent the user from injuring themselves or others. Additional requirements of the system are non-obstructive features and seamless transitioning between wheelie conditions.

Upon researching the state of wheelie technology, existing products, such as …

Mobility Cart For Monoskiers, Bryce Petersen, Craig Miller, Aaron Kan, Tyler Meskin

Mechanical Engineering

This document represents the culmination of the senior design project of Team Monoski M.E. This project was in partnership with Disabled Sports Eastern Sierra (DSES), a volunteer-based, non-profit organization focused on providing people with disabilities opportunities to participate in outdoor activities. Our team was tasked with designing a device to help monoskiers at Mammoth Mountain load on and off the gondola with little to no assistance. Over the course of three quarters at Cal Poly, we designed, manufactured, and tested our mobility cart, consisting of a custom-made wheelchair with an integrated hydraulic lift.

Energy Comparison Of Air Conditioning Split System Vs. Solar Absorption Systems For A Prototype Educational Building, Hesham Safwat

Mechanical Engineering

this paper aims to study solar energy in Egypt and its potential utilization in solar thermal cooling (absorption technique). The paper includes a detailed proposed solar absorption cooling system for one building located at the British University in Egypt with maximum cooling load of 141.3 ton. A detailed design using a design software (TRNSYS) is introduced to model the system and for optimization. A cost analysis is finally included to compare the overall costs of both the proposed cooling system and the current system.

Transient Heat Storage Systems, Ian M. Sweeney, Brock M. Johnson, Todd K. Lundberg

Mechanical Engineering

Phase change materials (PCM) have many applications in transient cooling systems, including those with high transient heat loads and low duty cycles. These materials allow a system to remain within a narrow temperature range with a relatively low weight compared to conventional heat sinks or high-power cooling systems. This senior capstone project includes the design of a PCM based thermal energy storage system to integrate into an existing cooling loop, as well as a determination of viable PCM’s for the application. This report contains the necessary information to build the test apparatus.

Wheelchair Tire Change, Vincent Aguilar, Martin Perez-Guzman, Spencer J. Solano

Mechanical Engineering

This project consists of a rear wheel wheelchair lift to be designed and created by a Cal Poly senior project team. This project was created for injured veteran Ms. Landeen who has the trouble of tracking mud into her house because of dirty wheelchair tires. The project was presented by the non-profit organization The Quality of Life Plus (QL+) Program. Much like when you remove your shoes coming into your home, Ms. Landeen needs a way to exchange her outdoor wheels for her clean indoor wheels.

The expected outcome of this project is a fully functioning device that will safely …

Verification Of Brand Authentication Technology Using Infrared Light And Image Processing, Thomas Fenner, Kevin Whalen, Josh Oliver

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Theatrical Turntable, Liam R. Martinez, Isaac Becker, Robert R. Reed, Caroline A. Whelan

Mechanical Engineering

No abstract provided.

Beach Wheelchair Attachment, Abbey Jo Scholle, Jackson Dallas Wiley, Jackson Cole

Mechanical Engineering

This document includes the problem that is under scrutiny, the background research towards finding a solution, the objectives, scope of the project, the planned overall design process, the preliminary design we have produced and analyzed, the critical design we have manufactured, the testing and results, and the final assessment of the produced design. The problem is lack of easy access and movement for wheelchair users on the beach. Other solutions and designs have been logged under background research. With this information, the scope of work was designed to meet all the needs specified and describe how the specifications will be …

Retractable Hammock, Collin J. Richardson, Jesse Bryn Mandell, Owen Alle Guenther

Mechanical Engineering

This Final Design Review will recap the objectives, background, design ideation, and concept development of the Retractable Hammock senior capstone project and continue to report on the final design and manufacturing that resulted in the final iteration of the Retractable Hammock.

Annuloplasty Mti: Improved Tooling For Annuloplasty Ring Manufacturing, Justin David Smith, Spencer Lee Combs, Luke Edward Maly

Mechanical Engineering

The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Laser Triangulation Sensor, Jake Finelt, Kian Gruszczynski, Greg Mclorg

Mechanical Engineering

Statement of Disclaimer: Since this project is a result of a class assignment, it has been graded and accepted as fulfillment of the course requirements. Acceptance does not imply technical accuracy or reliability. Any use of information in this report is done at the risk of the user. These risks may include catastrophic failure of the device or infringement of patent or copyright laws. California Polytechnic State University at San Luis Obispo and its staff cannot be held liable for any use or misuse of the project.

Identification System For Heart Valve Manufacturing, Nicholas Robert Jensen, Edgar Davis Nix, Judith Evelyn Gonzalez, Albert Austin Liddicoat

Mechanical Engineering

Abstract withheld due to NDA constraints

Treadmill User Centering, Cecilia Hill Yan Yuen, Donavan Chandler Feliz, Ariel Mae Arce Crisostomo, Adam Charles Patrella

Mechanical Engineering

The goal of team CENTREAD was to design a device to allow a person with a visual disability to run efficiently and effectively on a treadmill without fear of falling off or injuring themselves. The customer wished for the device to be small, lightweight, and have an easy, autonomous setup, while providing feedback to the user wirelessly for them to correct their own movement. The ultimate goal of the device is to allow the user to be comfortable, safe, and free while using it in order to ensure they have the best running experience. The device utilizes ultrasonic sensors in …

Nathan's Mobility Device, Steven A. Decsesznak, Matthew Brenholdt, Lansen Eto, Moulay Salahdin

Mechanical Engineering

Nathan’s Mobility Device is a California Polytechnic State University senior project composed of a team of four mechanical engineering students that designed, built and implemented a specialized seat on an existing mobility device. Nathan, the sole beneficiary of this project, is an 11-year-old boy afflicted with a condition known as Spinal Muscular Atrophy (SMA) which causes him extreme muscular weakness. In this report, the team discussed the problem at hand, provides preliminary research and product benchmarking (evaluation and comparison to specific criteria), and described the ideation, prototyping, testing, and iteration plan. In addition, the team explored the final design in …

Transcatheter Heart Valve Leaflet Assembly Tooling Improvement Final Design Report, James Craig Sherman, Zachary Robert Dicks, Luke Edward Williams

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Composite Suspension For A Mass Market Vehicle, Sarah M. Chapiama, Brian Auyeung, Jose Guerrero, Ethan Lau

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Curb Navigation, Cole A. Tudor, Kaitlyn R. Adams, Robbie Huerta

Mechanical Engineering

The Curb Navigation senior project, proposed by the QL+ organization, was presented to find a solution to an issue a former veteran, Velette, is having. Velette has a difficult time maneuvering curbs when out doing day-to-day errands and activities. The goal of this project is to develop a solution that will give Velette the ability to traverse curbs without the assistance of others or the need to do a wheelie that can lead to an injury. The team has found that adapting and optimizing an anti-tipper design may be the best way to solve the proposed challenge. The team decided …

Driver Cooling System, Joseph Fatin Bolous, Jake Donald Deboer, Alvin Theodore Lau

Mechanical Engineering

This document provides our Final Design Review (FDR) for the Driver Cooling System Project. It contains our background research, which includes current product research, technical research, and information on our sponsor’s needs as a customer as well our manufacturing process, test results, and final design. We created a problem statement to define the scope of the project, discuss sponsor and consumer needs and wants, and technical specifications. After brainstorming, we ultimately selected a thermoelectric cooling system (TEC) after presenting our Preliminary Design Report and Critical Design Report. We built the final prototype, as can be seen in the manufacturing plan, …

Dynamic Model For Simulating Motion Of The Right Ventricle, Brian Michael Larsen, Sam Koopman Porter, John Francis D'Ambrosio

Mechanical Engineering

This report documents all the research, ideation, and mockups used to determine right ventricle motion and develop a system capable of reproducing that motion on a tissue sample. The model is intended for evaluating anchoring systems being developed by Edwards Lifesciences for use with tricuspid valve therapies. Several design solutions were considered for the primary functions of recreating motion of the right ventricle and attaching tissue to the device. From these ideas a primary means of producing motion and attaching tissue was selected. These ideas were then developed over the course of a school year to become the final system …

Additive Manufacturing Powder Removal, Madison A. Lignell, Tyler W. Laird, Kurt K. Reed

Mechanical Engineering

Metal powder-bed fusion is an additive manufacturing process which enables the creation of unique shapes in metal parts that would otherwise be difficult, expensive, or impossible to machine. Metallic powder is melted and fused together by either a laser or electron beam to produce parts quickly. The excess powder covers newly printed parts and can be difficult to remove from small internal features. The scope of this project is to design a device that effectively removes the powder from newly printed parts safely, while reclaiming as much powder as possible for reuse. The solution for this project must be able …

Mechanical Team Final Design Report: Same Polytechnic College, Meghan L. Smith, Katie D. Nute, Long T. Hoang

Mechanical Engineering

The purpose of this document is to communicate the research, findings, and recommendations of the mechanical engineering team regarding the Same Polytechnic College project. This report includes a discussion of the design process utilized by the interdisciplinary team to construct preliminary building designs for both classroom and dormitory building modules. The mechanical team conducted testing using the wind tunnel to verify major building envelope design decisions. The following report also includes an explanation of the thermal testing that the team conducted to measure the thermal conductivity, diffusivity, and specific heat of bricks made to mimic those made locally in Same, …

3-Dimensional Automated Heat Flux Calibration Device, Victor Raul Chacon, David Madison Morrisset, Alex Michael Schnorr, Kevin Scott

Mechanical Engineering

This document aims to describe the problems in current radiant heat source heat flux calibration techniques and the approach our team took to solve them through automation. The following sections outline the basic premise of the problem we addressed and who our end product benefited. The proceeding sections addresses the research that we have performed regarding heat flux measurements and automation. This research includes current solutions – mostly partial solutions for problems that are similar but not exactly like ours. Following the background research, we define objectives, with specific details that outline how we evaluated different possible solutions, and how …

Metal Foam Drying Process, Bryce Zander, Ethan Serpa, Daniel Moore, Michael Mullen

Mechanical Engineering

Design and construction of machine to increase the throughput of metal foam that ERG Aerospace produces.

Upgrading The Sr-30 Miniature Turbojet For Adaptable Exhaust, Shannon Ferreira, Erin Mcmurchie, Peter Pratt

Mechanical Engineering

The California Polytechnic State University, San Luis Obispo (Cal Poly, SLO) Aerospace Department is requesting a variable nozzle adaptation for their SR-30 turbojet engine. The nozzle is intended for laboratory use in sophomore and junior level courses to supplement instruction on the effects that exhaust behavior has on the performance of propulsion technologies. Topics covered during a performance study of the SR-30 turbojet engine will include, but are not limited to: Brayton Cycle analysis, turbojet operation in ideal and non-ideal test conditions, instrumentation limitations, and basic nozzle operation. The SR-30 turbojet engine is similar in design and operation to engines …

Prove Endurance Car Front Suspension, Lauren A. Williams, Logan Simon, Justine G. Kwan

Mechanical Engineering

This document details the collaborative Mechanical Engineering Senior Project with Cal Poly PROVE Lab on PROVE Lab’s Project 2; an electric vehicle designed to travel 1000 miles on a single charge. Logan Simon, Justine Kwan, and Lauren Williams are given the challenge of designing an innovative proof of concept front suspension suspension for this vehicle.

After detailed research of new suspension systems, it was determined that the innovative nature could be in the form of unique manufacturing methods, materials use, or mechanical design. At this point in time, this vehicle is a purely conceptual design with no concrete requirements. Therefore …

Mobile Opera Backdrop, Juan Villalobos, Robbie Behlman, Kevin Valencia

Mechanical Engineering

Opera San Luis Obispo requires an acoustically projecting stage backdrop for their future plan of deploying a mobile opera house. The custom stage backdrop must be low-cost, easy to assemble and must project the performance sound to outdoor audiences. Other design requirements include being transportable in a step van, the ability to be assembled quickly by a crew of two, resistance to various outdoor conditions, the ability to mount accessories from the walls, and should meet a budget of $5,000. With the scope of the project understood, the three-quarter project is outlined. During the first quarter, the main deliverables included …

Purple Urchin Removal, Cullen Goss, Wil Gilbreath, Kevin Marshall

Mechanical Engineering

Soaring purple urchin populations have contributed to a greater than 90% reduction of northern California’s bull kelp forests. Human intervention to reduce the purple urchin population may allow localized kelp patches to grow. The California Department of Fish and Wildlife requested that our team develop a mechanical device to aid in the removal of the urchins. This document provides an update from the scope of work and details the process conducted to reach a scale final design. In this document, we provide background research to show our understanding of urchins and their effect on kelp forests. Then, we analyze the …

Team Joseph's Bike Trailer, Keely Thompson, Curtis Wathne, Ryan Meinhardt

Mechanical Engineering

This final design report shows the results of this senior project’s design process of creating a custom bike trailer for Team Joseph. As done in the Scope of Work, Preliminary Design report, and Critical Design report, current products, relevant technologies, and American Society for Testing and Materials (ASTM) standards are fully researched and benchmarked to aid in the design selection process. Customer requirements are looked at and developed into engineering specifications. A detailed design was created for CDR to show to Team Joseph, and manufacturing and testing plans were laid out. This final design report adds the final design revisions …

Universal Studios Hollywood Vip Trolley - Roller Frame, Jeffrey Ploss, Chase Montague, Lincoln Treanor

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Multi-Purpose Heart Valve Therapy Assembly Fixture, Alec John Foster, John Patrick Hofstetter, Emily Lim

Mechanical Engineering

STATEMENT OF CONFIDENTIALITY: The complete senior project report was submitted to the project advisor and sponsors. The results of this project are of a confidential nature and will not be published at this time.