Mechanical Engineering Commons^™

Cylinder-Head Surface Temperature And Maximum Pressure In A Diesel Engine, Jayant M. Patel

Masters Theses

"This report presents the result of an experimental investigation on the effect of 1) fuel consumption in a diesel engine on the mean cylinder-head surface temperature 2) engine speed and load on the maximum cylinder pressure.

A fast-response thermocouple was fixed in the cylinder head and temperatures were measured for various load and speed conditions. An attempt was made to record a transient surface temperature versus crank-angle diagram. Some doubt as to the reliability of this recording may arise because of the very small amount of time lag in the thermocouple action. This is immaterial to the subject of this …

The Development And Evaluation Of An Experimental Technique To Determine Stress Distribution In Uniformly Loaded Flat Plates, James William Walker

Masters Theses

"This thesis reports and evaluates an experimental technique that was developed to determine and monitor the stresses in a simply supported, uniformly loaded circular plate. Deflections are less than half the thickness of the plate. The application of the developed technique to plates whose integrity has been compromised with holes in various locations is discussed.

Resistance strain gages were used to determine experimentally the stresses in a simply supported, uniformly loaded circular plate with and without a concentric hole. The accuracy of the experimental results was established to be within approximately six percent of theoretical.

Proper application of the experimental …

Determination Of The Temperature Distribution Of The Ionized Portion Of The Jet From A Vortex Stabilized Plasma Generator Operating On Argon, G. Douglas Schellman

Masters Theses

"The interim thesis deals with the determination of the temperature distribution of a plasma jet operating on argon. It is the purpose of this thesis to present in detail the experimental process used and make a correlation of the experimental and theoretical results.

A copper enclosure was placed around the protruding flame, and the embedded thermocouple readings were taken and recorded. A stagnation temperature probe was inserted in the enclosure and moved both axially and transversely toward the flame taking readings at each pre-chosen interval. The exit temperature of the jet was obtained from a total energy balance.

From the …

The Design And Construction Of A Shock Tube Facility, William Adolph Crede

Masters Theses

"It is the object of this thesis to give an account of the considerations necessary to design, construct, and operate a shock tube facility.

The primary purpose of the facility was to provide a means to study high strength shock waves in physics, chemistry, and aerodynamic applications.

Preliminary designs were undertaken to determine the basic dimensions and related capabilities. Final design, construction and testing of the tube itself was performed by Nooter Corporation in St. Louis, Missouri. Preliminary designs agreed rather closely with final construction.

Experimental testing was confined to the successful operation of all the various components of the …

Turbulence In Journal Bearings, Kashyap R. Mehta

Masters Theses

"In this investigation, an experimental study was performed on a journal bearing under laminar and turbulent flow conditions. Using relationships for friction factor developed previously by other investigators a comparison was made with results of this present investigation. Since the flow changes from laminar to turbulent with a change in speed of rotation, curves for friction factor as a function of speed were plotted. Various attempts to make the recording and measuring systems more sensitive were also made and are discussed in this thesis"--Abstract, page ii.

A Photoelastic Study Of The Effect Of Certain Geometric Variables On The Plane Stress Distribution In An Electrical Insulator Body, Richard L. Pendleton

Masters Theses

"Photoelastic models were used to indicate stress patterns in various geometrically designed shapes. Each model represented a two-dimensional cross-section of the interior portion of an axially symmetrical porcelain electrical insulator. Five different loading pins were combined with three loading heads to produce eleven models. The maximum stress in each model was determined using a photoelastic method of stress analysis. An attempt was made to select the best structural design to be used in an electrical insulator. The test results indicate that the most desirable stress distribution is obtained using a single step loading pin and that the loading head angle …

The Design And Construction Of An Instrument For Calibrating Accelerometers, Richard Rabenau

Masters Theses

"The purpose of this work was to design and construct a facility to calibrate accelerometers. A ceramic piezoelectric shaker and modified Michelson interferometer together with necessary electronic equipment were used. The system produced accurate and stable acceleration at five discrete points from 1,000 to 5,000 cycles per second. the maximum calibration levels were approximately 50 g's"--Abstract, page ii.

Application Of The Photoelastic Coating Method To Evaluate The Stress Distribution On The External Surface Of The Cap Of An Electrical Insulator, Harijeetsinh Jagtiani

Masters Theses

"The Photoelastic Coating Method was applied to find the surface stresses on the cap of an electrical insulator. The strain distribution was observed and photographed. This color photograph indicated a visible geography of the maximum shear strain distribution in the region of the insulator where the birefringent plastic was bonded with a reflective cement. The Oblique Incidence technique was used to determine the principal stresses from the maximum shear strain (or the principal strain difference) readings, obtained from Normal Incidence. The critical cross-section of the insulator head was optically located, giving an initiative for the re-design of the insulator cap. …

Instrumentation Of A Diesel Engine For Measuring Cylinder Head Temperature, And Pressure At Various Crank Angles, Raman A. Patel

Masters Theses

"In this investigation, an attempt has been made to measure the instantaneous pressures in the cylinder and the transient temperatures of cylinder head versus crank angle in a Diesel engine. A strain-gage pressure transducer and a sensitive surface thermocouple were used. The pressure transducer was practically free from temperature influence and strain effects caused by installation. It had a greatly reduced sensitivity to vibrations compared with other available types of pressure transducers. The thermocouple had a very short response time. A device enabling very accurate measurement of crank-angle was constructed. Appropriate quantities were displayed on the screen of an oscilloscope …

Free Convection Heat Transfer From An Inclined Heated Flat Plate In Air, Shu Chien Yung

Masters Theses

"An experimental investigation has been performed to determine the free convection heat transfer from a heated flat plate in air moved from the vertical position through three inclined positions to the horizontal position. The hot surface of the plate was facing downward for the horizontal and three inclined positions. Tests were performed at plate surface temperatures from 120°F up to 404°F. Data for the plate surface temperature at about 165°F with the plate in the vertical position agrees very well with previous experimental work. This same data was used to determine a new parameter, introduced into the Pholhausen free convection …

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

Analysis Of The Flow Characteristics Through A Water Pressure Regulator, Anthony Lee Jatcko

Masters Theses

"This thesis presents an analysis of the flow characteristics through a water pressure regulator. Characteristic curves of the relationship between pressure drop through the regulator and flow through the regulator are developed. To further analyze these relationships, a least squares computer analysis was used to develop equations to fit these curves. An investigation into the modes of dissipating pressure energy in this type of regulator tends to indicate that a significant portion of the energy is lost through viscous shearing action in the area of high turbulence. The aforementioned characteristic curves also showed definite critical pressure points in the form …

Heat Transfer Coefficients Across Bonds And Contacts, Eugene Charles Fadler

Masters Theses

"The purpose of this investigation was to experimentally determine heat transfer coefficients across interfaces, including the effects of the thermal conductivity of the adherends, the hardness of the adherends, the bond thickness, and the type of adhesive.

Aluminum alloy, steel, copper, and extruded nylon rods were used as adherends; all 1.875 inches diameter and 8 inches long. Each was cut radially at its midpoint and faced off to the desired surface finish. Bare interface tests were conducted before the adherends were bonded together. The adhesives used were high grade silica refractory cement, two-part epoxy resin adhesive, and thermosetting synthetic rubber-phenolic …

A Study Of The Non-Newtonian Turbulent Fluid Flow Through An Annulus, Yogesh R. Parikh

Masters Theses

"This investigation is concerned with the study of non-Newtonian flow through an annulus. The experimental analysis of incompressible non-Newtonian fluids in a long cylindrical annulus of radius ratio 0.375 was studied in the turbulent region. Different types of non-Newtonian fluids were used to procure flow behaviour for the annulus.
The effect of increasing flow rate of the non-Newtonian fluids was evaluated by gathering pressure drop data across the annulus using a differential manometer. The power-law model is used in this study to characterize the non-Newtonian flow. The parameters of the power-law model were evaluated by gathering viscometric data on a …

A Study Of Radiation Heat Transfer In Rectangular Ducts And Enclosures, Jenn-Wuu Ou

Masters Theses

"The purpose of this study is to determine the radiant heat transfer in rectangular configurations and construct a general computer program. Two specific cases are studied in this work. The first case is a rectangular duct with openings at each end. The duct is separated into two sections which are called the source and the sink respectively. A linear temperature profile is imposed on the source section. The energy loss of both the source and the sink is investigated. The second case is a complete rectangular enclosure. The two end plates are called the source and the sink respectively. A …

An Apparatus To Measure Capillary Jet Thrusts And The Evaluation Of Normal Stresses In Fluids, Charles Donald Green

Masters Theses

"The purpose of this work was to design, construct and calibrate simple, inexpensive apparatus which could be used to measure the normal stresses and tangential shear stresses of a fluid. For normal stress measurements, the capillary jet thrust principle was selected. A standard analytical balance was modified so that capillary tubes could be fitted on it horizontally. It was designed so that the thrust produced by a jet of fluid from the tube caused a deviation from the zero balance position. The weights needed to rezero the balance gave a measure of the thrust"--Summary, page 1.

The Effect Of Lubri-Coolant Application At The Tool-Chip Interface On Tool Forces, Bomi Ardeshir Hathikhanavala

Masters Theses

"The purpose of this experiment was to determine the effectiveness of a lubri-coolant directed in such a way that it impinged just below the chip at the tool-chip interface in an orthogonal cutting process. This was compared to the conventional method of flooding lubri-coolant around the tool-chip area ... The results obtained show that the forces required to cut a material were less if the lubri-coolant was directed on the tool-chip interface when larger values of feed and depth of cut were used, and that with smaller values of feed and depth of cut, the method of flooding was equal …

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …

A Rubber Membrane Analogy For The Study Of Shafts In Torsion., Myron D. Bruns

Masters Theses

"The thesis presents a review of literature giving reference to several books which present the many and varied methods of determining the shearing stresses in shafts. However, no reference was found that used a rubber membrane analogy similar to that used in th is thesis. The theory of torsion, the membrane theory, and its analogy have been presented for a better understanding of the subject. Illustrations are used freely for clarity.

Analytical methods and solutions are given for two problems. The first method is that of writing a Saint-Venant stress function and satisfying the necessary conditions for it to be …

A Study Of Rotational Critical Speeds For A Multi-Mass System By Influence Coefficients, Kantikumar G. Patel

Masters Theses

"In this investigation an attempt has been made to determine the critical speeds of a multi-mass rotational system by using influence coefficients. Modes of vibrations are also examined at these critical speeds.

A shaft carrying five masses, supported by bearings at the ends, has been studied analytically. The length of the bearings is considered small with respect to the shaft length and therefore, the configuration is assumed to be point supported as a simple beam. The five masses, each weighing one pound, were placed at equal distances of 10 inches on a 60 inch shaft. The critical speed was examined …

Minimum Frictional Characteristics Of Optimum Journal Bearings., Navinchandra F. Shah

Masters Theses

"This investigation was conducted to develop a graphical representation to determine the optimum bearing conditions for minimum friction and to establish a theoretical approach for journal bearing design.

A series of graphs has been plotted for· the coefficient of friction versus the eccentricity ratio based on the. Sommerfeld number derived from Reynolds' differential equation, f or optimum journal bearings.

The results obtained in this research have been compared with those developed by other investigators. This comparison confirms the validity of the results presented in this thesis, so that it could be used advantageously for the design of optimum journal bearings"-- …

Forced Convection Heat Transfer Coefficients And Induction Heating, Max Edwin Light

Masters Theses

“The purpose of this study was to design and build an apparatus to experimentally determine the convective heat transfer coefficients for water flowing in a horizontal tube at turbulent flow. Also it was planned to use the apparatus to investigate the spatial dependence of energy deposition by induction heating.

An instrument and measuring techniques were developed that gave reasonable correlations between experimentally determined heat transfer coefficients and values calculated from generally accepted heat transfer relationships developed by other experimenters. Most of the calculated values were within ± 10% of the experimental values for a wide range of flow rates.

It …

The Effects Of Granular Size On The Thermal Conductivity Of Sand, Kanubhai M. Patel

Masters Theses

"The thermal conductivity of granular materials can be determined by the Thomas method. This method was used here to determine the effects of granular size on the thermal conductivity of sand. A river sand was secured and screened. The sand retained between the Tyler Standard Screen Scale, mesh 10 and 14, 14 and 28, 28 and 40, 40 and 48, 48 and 60, and below mesh 60, was used for tests.

The thermal conductivity for the above six samples obtained by the author coincide fairly well with published data.

It is reported in the International Critical Tables that the thermal …

The Design, Construction, And Calibration Of An Angular Accelerameter., Walter Earl Palm

Masters Theses

"The purpose of this work was to design, construct, and calibrate an angular accelerometer for continuous operation. The design uses four symmetrically placed springs connecting a ring and hub. Strain gages are mounted on the springs in a Wheatstone bridge arrangement. When the entire unit is subjected to an angular acceleration, the ring deflects causing an output voltage. This voltage is proportional to the deflection which is shown to be a function of the angular acceleration. The accelerometer was constructed to operate at frequencies up to 120 cps. The calibration was accomplished by using a simple harmonic motion input"-- Abstract, …

The Design, Construction, And Evaluation Of A Vortex Stabilized Plasma Generator, Ronald Ray Williams

Masters Theses

“This report presents the design, construction, and evaluation of a vortex stabilized arc plasma generation facility operating on argon.

The facility consisted of five basic systems; the plasma genera- tor, the electrical power system, the argon flow system, the cooling system, and instrumentation.

The facility was designed to meet four general requirements; stable arc operation, low electrode deterioration, low cost of construction, and provisions for determination of the operating characteristics and thermal properties of the plasma.

Experimental results obtained in the laboratory agreed well with the design conditions. The rate of energy dissipated in the electric arc varied from 7. …

The Effect Of An Induction Field On Transducers., Ratilal S. Patel

Masters Theses

"This report presents the results of an experimental investigation on the effect of an induction field on transducer output. Various types of transducers; strain gages, thermocouples, and thermistors, were used. The changes in the output of these transducers were measured for various induction field conditions.

Measurements must often be made where strong electrical fields are present. Strain gages are used to measure the stresses in electrical machinery. Thermocouples and thermistors used for measuring the temperature of materials undergoing heat treatment with an induction heater are also subjected to an induction field.

The general experimental procedure was the same throughout the …

Solid-Phase Welding Of Nodular Iron To Low Carbon Steel., Scott H. Carriere

Masters Theses

“This paper presents an experimental investigation of the possibility of using solid-phase welding to join nodular iron to low carbon steel. Included is a review of available literature on solid-phase welding, tracing its origin from early Egypt to the present day. There was no previously reported work found on the welding of nodular iron to steel.

Experiments were performed to determine what temperature-pressure combination gave the greatest ultimate tensile strength These experiments resulted in the best welds being produced with an end load of 7000 pounds (35.700 psi) on a half inch diameter sample. The majority of these welds proved …

The Importance Of Radiation As A Means Of Controlling Surface And Internal Temperatures Of A Semi-Infinite Solid, Kenneth C. Woodruff Jr.

Masters Theses

"This problem is concerned with the temperature history of a semi-infinite solid bounded by one flat surface.

Heat was applied by convection from a hot fluid to the flat surface of the solid which was originally at a uniform temperature. Heat was radiated from the flat surface to black space and conducted into the solid according to Fourier's law. The temperature at the surface, and at several points beneath the surface, was determined as a function of time.

A method for solution of such a problem is demonstrated here by the use of numerical analysis and the Royal McBee LGP …

A Determination Of The Theoretical Stresses In A Deep Beam., James William Tritz

Masters Theses

"This paper presents an analytical solution of the stress distribution in a deep beam of finite length. The beam being considered is analyzed as one of plane stress. The method employed superimposes two stress functions each of which is a trigonometric series. The first stress function satisfies all boundary conditions except that of zero stress on the vertical faces. The second function is found, so that, when combined with the first function, all boundary conditions are satisfied. The IBM 1620 digital computer is then used to find the stresses for a particular beam. The results of this analysis are then …

Investigation Of The Effect Of The Wall Thickness On The Residual Stresses Developed In Thick Wall Cylinders Due To Water Quenching From The Outside Surface., Ghanshyam Chandubhai Patel

Masters Theses

"This investigation has been made to determine the residual stresses in thick wall cylinders by the use of strain gages.

The cylinders were quenched from their outer surface i n water from a temperature of 1000°F, and the resulting residual stresses were determined by Sachs boring-out method. The effect of the wall thickness of the cylinders on the residual stresses and the error developed due to the boring operation were discussed"--Abstract, p. ii