Mechanical Engineering Commons^™

A Study Of The Effect Of A Square Cutout On The Moment Distribution In A Simply Supported Rectangular Plate Under Normal Concentrated Load By The Moiré Fringe Method, Taher F. Raja

Masters Theses

"Plexiglass models were used to produce Moiré fringes for two different geometrical shapes. The moments in the case of a simply supported rectangular plate with a normal concentrated load were found using the Moiré fringes which directly give the gradients at all points of the surface of the model. The variation of the moments due to a square cutout was also studied by this method. As a check for the experimental method, the analytical solution was presented for the plate without a cut-out. The Moiré method yields moments to an accuracy of 3 to 15 percent, however, care must be …

Effect Of Artificial Roughness On Convection, Lee W. Burford

Masters Theses

"Considerable work has been done in recent years, and is still being done, to find ways of increasing the heat transfer rate in fluid heat exchangers. One particular type of potential heat exchanger that has been studied analytically, as well as experimentally, is the use of artificially roughened tubing.

The test sections used in this experiment consisted of four aluminum pipes, three of which have been artificially roughened internally by machining ninety- degree V-shape grooves along the axis of the pipes. The grooves were 30/1000, 60/1000, and 90/1000 inches in depth. The remaining pipe was a smooth test section with …

Empirical Evaluation Of The Eccentric Orifice In Small Diameter Pipes, Gary A. Hinz

Masters Theses

"This investigation has taken different orifice sizes (0.3005", 0.4000", 0.5045", 0.6015") and tested their flow characteristics when used in a 1" diameter pipe. Each orifice was initially placed in a fully eccentric position, that is the circumference of the orifice was placed tangent to the inside circumference of the pipe. Data was taken with the orifice eccentric to concentric in increments of 0.050".

Plots of flow coefficient versus Reynold's number were made for each position of the four orifices tested.

Empirical equations were developed for determining the flow coefficient of the various orifice sizes placed in any eccentric position.

It …

Measurement Of The Velocity And Temperature Profiles Of Air Swirling Through A Conical Shaped Nozzle, Stephen Abner Thompson

Masters Theses

"A study was conducted to determine the velocity and temperature distributions in swirling flow of air through a converging nozzle. Radial traverses were taken at three axial positions with a specially designed pitot tube constructed of hypodermic needles. The most significant finding was the large magnitude of the radial velocity component. A combination of reversed axial flow along the nozzle axis, and an outward flow near the nozzle surface was also experienced. An increase of temperature with increasing radial position may be attributed to the Ranque-Hilsch effect"--Abstract, page ii.

Calibration Of An Instrument To Calibrate Accelerometers, Nader Khorzad

Masters Theses

"The purpose of this research was to calibrate an instrument with which an accelerometer could be calibrated accurately. The instruments used were a piezoelectric shaker and a modified Michelson interferometer together with necessary electronic equipment. This equipment was used to calibrate a Kistler Model 808A accelerometer.

Weight was added to the shaker in the second part of this experiment in order to determine its effect on the amplitude and frequency of oscillation of the shaker.

Results show that this instrument may be used to calibrate an accelerometer quite accurately. The weight added to the shaker will effect only the amplitude …

A Fluid Control System For Nuclear Reactors, Roger Alan Crane

Masters Theses

"This thesis presents both an experimental and analytical analysis of the scram characteristics of a fluid control system for a nuclear reactor. This control system utilizes a control tube containing a neutron-absorbing fluid. The level of the fluid inside of the tube is then regulated by means of' a pressurized gas and offers a number of unique advantages over the conventional control rod system using linear absorber rods.

The effect of varying the level-control pressure and initial height of the fluid column is determined and evaluated. The time required to complete a scram with the fluid control system is compared …

Transient Temperature Distribution In A Finite Cylinder And An Infinite Cylinder Subjected To Some Boundary Conditions, Harng-Sen Huang

Masters Theses

"This thesis is concerned with the theoretical heat transfer analysis of solid cylinders. The first problem considered is the transient temperature distribution in a finite cylinder. This cylinder has a uniform initial temperature and a uniform constant surrounding temperature. This case is solved by the separation of variables. Combining the charts for the infinite cylinder and the charts for the infinite plate one can determine the solution to this case easily. If a uniform constant surface temperature is prescribed instead of a surrounding temperature, the solution can be obtained from the previous one by charging the Nusselt number to infinity. …

Cylinder-Head Surface Temperature And Maximum Pressure In A Diesel Engine, Jayant M. Patel

Masters Theses

"This report presents the result of an experimental investigation on the effect of 1) fuel consumption in a diesel engine on the mean cylinder-head surface temperature 2) engine speed and load on the maximum cylinder pressure.

A fast-response thermocouple was fixed in the cylinder head and temperatures were measured for various load and speed conditions. An attempt was made to record a transient surface temperature versus crank-angle diagram. Some doubt as to the reliability of this recording may arise because of the very small amount of time lag in the thermocouple action. This is immaterial to the subject of this …

The Effect Of Lubri-Coolant Application At The Tool-Chip Interface On Tool Forces, Bomi Ardeshir Hathikhanavala

Masters Theses

"The purpose of this experiment was to determine the effectiveness of a lubri-coolant directed in such a way that it impinged just below the chip at the tool-chip interface in an orthogonal cutting process. This was compared to the conventional method of flooding lubri-coolant around the tool-chip area ... The results obtained show that the forces required to cut a material were less if the lubri-coolant was directed on the tool-chip interface when larger values of feed and depth of cut were used, and that with smaller values of feed and depth of cut, the method of flooding was equal …

The Eccentric Orifice As A Flow Measuring Device In Small Diameter Pipes, James E. Casale

Masters Theses

"This thesis reports and evaluates the use of an eccentrically placed orifice as a flow measuring device in small pipe sizes. The orifice is placed in a concentric location and moved to increasingly eccentric locations until full eccentricity is reached. At full eccentricity the circumference of the orifice is tangent to the circumference of the pipe. The effects of increasing eccentricity are evaluated for four orifices...Flow coefficients for the orifices in different locations are plotted against Reynolds numbers. The eccentric orifice is a reliable, accurate flow measuring device for metering or controlling the flow of fluids. Design criteria can be …

Analysis Of The Flow Characteristics Through A Water Pressure Regulator, Anthony Lee Jatcko

Masters Theses

"This thesis presents an analysis of the flow characteristics through a water pressure regulator. Characteristic curves of the relationship between pressure drop through the regulator and flow through the regulator are developed. To further analyze these relationships, a least squares computer analysis was used to develop equations to fit these curves. An investigation into the modes of dissipating pressure energy in this type of regulator tends to indicate that a significant portion of the energy is lost through viscous shearing action in the area of high turbulence. The aforementioned characteristic curves also showed definite critical pressure points in the form …

Application Of The Photoelastic Coating Method To Evaluate The Stress Distribution On The External Surface Of The Cap Of An Electrical Insulator, Harijeetsinh Jagtiani

Masters Theses

"The Photoelastic Coating Method was applied to find the surface stresses on the cap of an electrical insulator. The strain distribution was observed and photographed. This color photograph indicated a visible geography of the maximum shear strain distribution in the region of the insulator where the birefringent plastic was bonded with a reflective cement. The Oblique Incidence technique was used to determine the principal stresses from the maximum shear strain (or the principal strain difference) readings, obtained from Normal Incidence. The critical cross-section of the insulator head was optically located, giving an initiative for the re-design of the insulator cap. …

A Study Of The Non-Newtonian Turbulent Fluid Flow Through An Annulus, Yogesh R. Parikh

Masters Theses

"This investigation is concerned with the study of non-Newtonian flow through an annulus. The experimental analysis of incompressible non-Newtonian fluids in a long cylindrical annulus of radius ratio 0.375 was studied in the turbulent region. Different types of non-Newtonian fluids were used to procure flow behaviour for the annulus.
The effect of increasing flow rate of the non-Newtonian fluids was evaluated by gathering pressure drop data across the annulus using a differential manometer. The power-law model is used in this study to characterize the non-Newtonian flow. The parameters of the power-law model were evaluated by gathering viscometric data on a …

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …

Instrumentation Of A Diesel Engine For Measuring Cylinder Head Temperature, And Pressure At Various Crank Angles, Raman A. Patel

Masters Theses

"In this investigation, an attempt has been made to measure the instantaneous pressures in the cylinder and the transient temperatures of cylinder head versus crank angle in a Diesel engine. A strain-gage pressure transducer and a sensitive surface thermocouple were used. The pressure transducer was practically free from temperature influence and strain effects caused by installation. It had a greatly reduced sensitivity to vibrations compared with other available types of pressure transducers. The thermocouple had a very short response time. A device enabling very accurate measurement of crank-angle was constructed. Appropriate quantities were displayed on the screen of an oscilloscope …

A Study Of Radiation Heat Transfer In Rectangular Ducts And Enclosures, Jenn-Wuu Ou

Masters Theses

"The purpose of this study is to determine the radiant heat transfer in rectangular configurations and construct a general computer program. Two specific cases are studied in this work. The first case is a rectangular duct with openings at each end. The duct is separated into two sections which are called the source and the sink respectively. A linear temperature profile is imposed on the source section. The energy loss of both the source and the sink is investigated. The second case is a complete rectangular enclosure. The two end plates are called the source and the sink respectively. A …

Free Convection Heat Transfer From An Inclined Heated Flat Plate In Air, Shu Chien Yung

Masters Theses

"An experimental investigation has been performed to determine the free convection heat transfer from a heated flat plate in air moved from the vertical position through three inclined positions to the horizontal position. The hot surface of the plate was facing downward for the horizontal and three inclined positions. Tests were performed at plate surface temperatures from 120°F up to 404°F. Data for the plate surface temperature at about 165°F with the plate in the vertical position agrees very well with previous experimental work. This same data was used to determine a new parameter, introduced into the Pholhausen free convection …

An Apparatus To Measure Capillary Jet Thrusts And The Evaluation Of Normal Stresses In Fluids, Charles Donald Green

Masters Theses

"The purpose of this work was to design, construct and calibrate simple, inexpensive apparatus which could be used to measure the normal stresses and tangential shear stresses of a fluid. For normal stress measurements, the capillary jet thrust principle was selected. A standard analytical balance was modified so that capillary tubes could be fitted on it horizontally. It was designed so that the thrust produced by a jet of fluid from the tube caused a deviation from the zero balance position. The weights needed to rezero the balance gave a measure of the thrust"--Summary, page 1.

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

The Development And Evaluation Of An Experimental Technique To Determine Stress Distribution In Uniformly Loaded Flat Plates, James William Walker

Masters Theses

"This thesis reports and evaluates an experimental technique that was developed to determine and monitor the stresses in a simply supported, uniformly loaded circular plate. Deflections are less than half the thickness of the plate. The application of the developed technique to plates whose integrity has been compromised with holes in various locations is discussed.

Resistance strain gages were used to determine experimentally the stresses in a simply supported, uniformly loaded circular plate with and without a concentric hole. The accuracy of the experimental results was established to be within approximately six percent of theoretical.

Proper application of the experimental …

Determination Of The Temperature Distribution Of The Ionized Portion Of The Jet From A Vortex Stabilized Plasma Generator Operating On Argon, G. Douglas Schellman

Masters Theses

"The interim thesis deals with the determination of the temperature distribution of a plasma jet operating on argon. It is the purpose of this thesis to present in detail the experimental process used and make a correlation of the experimental and theoretical results.

A copper enclosure was placed around the protruding flame, and the embedded thermocouple readings were taken and recorded. A stagnation temperature probe was inserted in the enclosure and moved both axially and transversely toward the flame taking readings at each pre-chosen interval. The exit temperature of the jet was obtained from a total energy balance.

From the …

The Design And Construction Of A Shock Tube Facility, William Adolph Crede

Masters Theses

"It is the object of this thesis to give an account of the considerations necessary to design, construct, and operate a shock tube facility.

The primary purpose of the facility was to provide a means to study high strength shock waves in physics, chemistry, and aerodynamic applications.

Preliminary designs were undertaken to determine the basic dimensions and related capabilities. Final design, construction and testing of the tube itself was performed by Nooter Corporation in St. Louis, Missouri. Preliminary designs agreed rather closely with final construction.

Experimental testing was confined to the successful operation of all the various components of the …

Turbulence In Journal Bearings, Kashyap R. Mehta

Masters Theses

"In this investigation, an experimental study was performed on a journal bearing under laminar and turbulent flow conditions. Using relationships for friction factor developed previously by other investigators a comparison was made with results of this present investigation. Since the flow changes from laminar to turbulent with a change in speed of rotation, curves for friction factor as a function of speed were plotted. Various attempts to make the recording and measuring systems more sensitive were also made and are discussed in this thesis"--Abstract, page ii.

Heat Transfer Coefficients Across Bonds And Contacts, Eugene Charles Fadler

Masters Theses

"The purpose of this investigation was to experimentally determine heat transfer coefficients across interfaces, including the effects of the thermal conductivity of the adherends, the hardness of the adherends, the bond thickness, and the type of adhesive.

Aluminum alloy, steel, copper, and extruded nylon rods were used as adherends; all 1.875 inches diameter and 8 inches long. Each was cut radially at its midpoint and faced off to the desired surface finish. Bare interface tests were conducted before the adherends were bonded together. The adhesives used were high grade silica refractory cement, two-part epoxy resin adhesive, and thermosetting synthetic rubber-phenolic …

A Photoelastic Study Of The Effect Of Certain Geometric Variables On The Plane Stress Distribution In An Electrical Insulator Body, Richard L. Pendleton

Masters Theses

"Photoelastic models were used to indicate stress patterns in various geometrically designed shapes. Each model represented a two-dimensional cross-section of the interior portion of an axially symmetrical porcelain electrical insulator. Five different loading pins were combined with three loading heads to produce eleven models. The maximum stress in each model was determined using a photoelastic method of stress analysis. An attempt was made to select the best structural design to be used in an electrical insulator. The test results indicate that the most desirable stress distribution is obtained using a single step loading pin and that the loading head angle …

The Design And Construction Of An Instrument For Calibrating Accelerometers, Richard Rabenau

Masters Theses

"The purpose of this work was to design and construct a facility to calibrate accelerometers. A ceramic piezoelectric shaker and modified Michelson interferometer together with necessary electronic equipment were used. The system produced accurate and stable acceleration at five discrete points from 1,000 to 5,000 cycles per second. the maximum calibration levels were approximately 50 g's"--Abstract, page ii.

Generalized Programs For Heat Transfer Analysis., Ceylung Chu

Masters Theses

"This report presents numerical methods for calculating temperature distributions in any physical system in which heat transfer is taking place. The syste.11 may be at either a steadystate condition or a transient condition. The temperature distribution may itself be or primary interest, or it may be used further to calculate the flow or heat or thermal stress.

The system under investigation is divided into a certain number of subdivisions, or so-called "regions". A reference point (node point) will be taken as representative for the region which includes that point. The temperature at the "node point11 is taken to be the …

Experimental Evaluation Of Thermal Stresses On The Outer Surface Of A Thick-Walled Tube., Vinodray T. Patel

Masters Theses

"In this investigation an attempt has been made to measure thermal stresses on the outer surface of a thick- walled tube. The inside surface was heated by steam passing through the tube while the outer surface was cooled by water. Two temperature compensated strain gages were used to measure strains in the tangential and axial directions respectively. The advantage of using this type of strain gage is to avoid the use of a dummy gage to compensate for the temperature effect.

The analytical solution to the problem was derived and the values of thermal stresses were calculated theoretically and compared …

The Effects Of Granular Size On The Thermal Conductivity Of Sand, Kanubhai M. Patel

Masters Theses

"The thermal conductivity of granular materials can be determined by the Thomas method. This method was used here to determine the effects of granular size on the thermal conductivity of sand. A river sand was secured and screened. The sand retained between the Tyler Standard Screen Scale, mesh 10 and 14, 14 and 28, 28 and 40, 40 and 48, 48 and 60, and below mesh 60, was used for tests.

The thermal conductivity for the above six samples obtained by the author coincide fairly well with published data.

It is reported in the International Critical Tables that the thermal …

A Determination Of The Theoretical Stresses In A Deep Beam., James William Tritz

Masters Theses

"This paper presents an analytical solution of the stress distribution in a deep beam of finite length. The beam being considered is analyzed as one of plane stress. The method employed superimposes two stress functions each of which is a trigonometric series. The first stress function satisfies all boundary conditions except that of zero stress on the vertical faces. The second function is found, so that, when combined with the first function, all boundary conditions are satisfied. The IBM 1620 digital computer is then used to find the stresses for a particular beam. The results of this analysis are then …