Mechanical Engineering Commons^™

Prototyping And Testing Of Solar Hybrid Pv-T Panels, Joel Aaron Lamson

Masters Theses

"The combination of photovoltaic and solar thermal (PV-t) systems has been proven to provide greater efficiency than their stand-alone counterparts. Previous studies on hybrid assemblies have found favorable results supporting the combination of both systems. The research presented here builds on the work competed here at Missouri University of Science and Technology (Missouri S&T) yielding favorable results of increased efficiencies as compared to stand-alone systems. The main difference between this experiment and previous research at Missouri S&T is that the hybrid PV-t is unglazed. The effect of an unglazed panel is shown to reduce the thermal output of the PV-t …

Microlens Array Light Trapping In Cdte/Cds Solar Cells, Patrick Michael Margavio

Masters Theses

"In light of the continued rise in fossil fuel costs, alternative energy sources, such as solar technology, are increasingly important. Concentrating photovoltaic systems are promising for future efficient and cost effective competition with fossil fuels. A microlens array is employed to a CdTe/CdS semiconducting solar cell to increase efficiency via light trapping. Since the microlens array will cause a local increase in incident light intensity, it should cause a corresponding increase in efficiency. The solar cell is deposited layer by layer. The CdS layer is chemically deposited. The CdTe layer is deposited using a novel additive manufacture technique: laser melting …

Biological Evaluation Of A Novel Tissue Engineering Scaffold Of Layered Double Hydroxides (Ldhs), Fateme Fayyazbakhsh, Mehran Solati-Hashjin, M. A. Shokrgozar, S. Bonakdar, Y. Ganji, N. Mirjordavi, S. A. Ghavimi, P. Khashayar

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Bone Tissue Engineering (BTE) Composed of Three Main Parts: Scaffold, Cells and Signaling Factors. Several Materials and Composites Are Suggested as a Scaffold for BTE. Biocompatibility is One of the Most Important Property of a BTE Scaffold. in This Work Synthesis of a Novel Nanocomposite Including Layered Double Hydroxides (LDH) and Gelatin is Carried Out and its Biological Properties Were Studied. the Co-Precipitation (PH=11) Method Was Used to Prepare the LDH Powder, using Calcium Nitrate, Magesium Nitrate and Aluminum Nitrate Salts as Starting Materials. the Resulted Precipitates Were Dried. X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron …

Manufacturing And Characterization Of Soy-Based Polyurethane Composites, Rama Bhadra Raju Vuppalapati

Doctoral Dissertations

"The major cost drivers for composites are raw materials and manufacturing process. Automated manufacturing processes like pultrusion and low cost bio-based raw materials can significantly lower the cost of composites. Polyurethane (PU) resin systems are being introduced in the pultrusion industry as they have higher performance characteristics and manufacturing feasibility when compared to conventional resin systems such as polyester and vinyl ester. PU resin systems are generally characterized as aromatic and aliphatic. Aliphatic PU has lower mechanical properties than the aromatic resin system due to its chemical structure. Nano materials can be used to increase the mechanical properties of aliphatic …

The Risk Mitigation Strategy Taxonomy And Generated Risk Event Effect Neutralization Method, Daniel A. Krus

Doctoral Dissertations

"In the design of new products and systems, the mitigation of potential failures is very important. The sooner in a product's design mitigation can be performed, the lower the cost and easier to implement those mitigations become. However, currently, most mitigations strategies rely on the expertise of the engineers designing a product, and while models and for failure modes do exist to help, there are no guidelines for performing product changes to reduce risk. To help alleviate this, the risk mitigation strategy taxonomy is created from an empirical collection of mitigation strategies used in industry for failure mitigation, creating a …

Highly Sensitive Refractive Index Optical Fiber Sensors Fabricated By A Femtosecond Laser, Jinpeng Yang, Lan Jiang, Sumei Wang, Qianghua Chen, Benye Li, Hai Xiao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Highly sensitive and robust refractive index (RI) fiber sensors are proposed, which are based on concatenating two micro air-cavities. the micro air-cavities embedded in the fiber along the core axis are fabricated by combining the techniques of femtosecond laser micromachining and arc fusion splicing. the full width at half-maximum (FWHM) of an attenuation peak of a sensor in air is 0.048 nm, and the extinction ratio is ∼15 dB. When the diameter of the cavity is slightly larger than the fiber core diameter, the sensor is highly sensitive to external RI changes. a high sensitivity of 172.4 nm/refractive index unit …

Effect Of Thin Film Confined Between Two Dissimilar Solids On Interfacial Thermal Resistance, Zhi Liang, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Non-Equilibrium Molecular Dynamics Model is Developed to Investigate How a Thin Film Confined between Two Dissimilar Solids Affects the Thermal Transport Across the Material Interface. for Two Highly Dissimilar (Phonon Frequency Mismatched) Solids, It is Found that the Insertion of a Thin Film between Them Can Greatly Enhance Thermal Transport Across the Material Interface by a Factor of 2.3 If the Thin Film Has One of the Following Characteristics: (1)a Multi-Atom-Thick Thin Film of Which the Phonon Density of States (DOS) Bridges the Two Different Phonon DOSs for the Solid on Each Side of the Thin Film; (2)a Single-Atom-Thick …

Improving The Efficiency Of Lpg Compression Ignition Engines For Passenger Cars Through Waste Heat Recovery, Alberto Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The turbocharged direct injection lean burn Diesel engine is the most efficient now in production for transport applications with full load brake efficiencies up to 40 to 45% and reduced penalties in brake efficiencies reducing the load by the quantity of fuel injected. the secrets of this engine's performances are the high compression ratio and the lean bulk combustion mostly diffusion controlled in addition to the partial recovery of the exhaust energy to boost the charging efficiency. the major downfalls of this engine are the carbon dioxide emissions and the depletion of fossil fuels using fossil diesel, the energy security …

Efficient Uncertainty Quantification In Multidisciplinary Analysis Of A Reusable Launch Vehicle, Benjamin R. Bettis, Serhat Hosder, Tyler Winter

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The objective of this study was to apply a recently developed uncertainty quantification framework to the multidisciplinary analysis of a reusable launch vehicle (RLV). This particular framework is capable of efficiently propagating mixed (inherent and epistemic) uncertainties through complex simulation codes. the goal of the analysis was to quantify uncertainty in various output parameters obtained from the RLV analysis, including the maximum dynamic pressure, cross-range, range, and vehicle takeoff gross weight. Three main uncertainty sources were treated in the simulations: (1) reentry angle of attack (inherent uncertainty), (2) altitude of the initial reentry point (inherent uncertainty), and (3) the Young's …

Alternative Crankshaft Mechanisms And Kinetic Energy Recovery Systems For Improved Fuel Economy Of Light Duty Vehicles, Alberto Boretti, Houshsng Masudi, Joseph Scalzo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The introduction of advanced internal combustion engine mechanisms and powertrains may improve the fuel conversion efficiency of an engine and thus reduce the amount of energy needed to power the vehicle. the paper presents a novel design of a variable compression ratio advanced spark ignition engine that also permits an expansion ratio that may differ from the induction stroke therefore generating an Atkinson cycle effect. the stroke ratio and the ratio of maximum to minimum in-cylinder volumes may change with load and speed to provide the best fuel conversion efficiency. the variable ratio of maximum to minimum in-cylinder volumes also …

Solid Oxide Fuel Cell Process And Apparatus, Mathew Ellis Cooper, David J. Bayless, Jason P. Trembly

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Conveying gas containing sulfur through a sulfur tolerant planar solid oxide fuel cell (PSOFC) stack for sulfur scrubbing, followed by conveying the gas through a non-sulfur tolerant PSOFC stack. The sulfur tolerant PSOFC stack utilizes anode materials, such as LSV, that selectively convert H₂S present in the fuel stream to other non-poisoning sulfur compounds. The remaining balance of gases remaining in the completely or near H₂S-free exhaust fuel stream is then used as the fuel for the conventional PSOFC stack that is downstream of the sulfur-tolerant PSOFC. A broad range of fuels such as gasified coal, …

Radiative And Nonradiative Decay Rates In Chromium-Related Centers In Nanodiamonds, S. Castelletto, Alberto Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We address for the first time the measurement of nonradiative decay rates in Cr-related centers in nanodiamonds. Compared to our previous quantum efficiency measurement of Cr centers created in bulk diamond, separate measurements of radiative and nonradiative decay rates in grown nanodiamonds prove more challenging due to size dependence effects. We demonstrate in this Letter that, using defocused dipole imaging and collection efficiency calculation via finite-difference time-domain (FDTD), a quantum efficiency up to 0.9 can be inferred to Cr-related centers showing a 2-level system photon statistics. © 2011 Optical Society of America.

Diesel-Like And Hcci-Like Operation Of A Truck Engine Converted To Hydrogen, Alberto A. Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In addition to the traditional spark ignition (SI), premixed, gasoline-like and compression ignition (CI), diffusion, Diesel-like operation of internal combustion engines, premixed, homogeneous charge, compression ignition (HCCI) operation has also been proposed to improve the fuel conversion efficiency and reduce the pollutant formation. to be attractive, the operation in HCCI mode has to be coupled with the other traditional operations, being HCCI in general difficult to be controlled and limited to values of the air-to-fuel equivalence ratio λ within a narrow windows set by the lean burn limits with large λ and the peak pressure limits with small λ. Furthermore, …

Direct Numerical Simulation Of Hypersonic Turbulent Boundary Layers. Part 4. Effect Of High Enthalpy, L. (Lian) Duan, M. P. Martín

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper we present direct numerical simulations (DNS) of hypersonic turbulent boundary layers to study high-enthalpy effects. We study high-and low-enthalpy conditions, which are representative of those in hypersonic flight and ground-based facilities, respectively. We find that high-enthalpy boundary layers closely resemble those at low enthalpy. Many of the scaling relations for low-enthalpy flows, such as van-Driest transformation for the mean velocity, Morkovin's scaling, and the modified strong Reynolds analogy hold or can be generalized for high-enthalpy flows by removing the calorically perfect-gas assumption. We propose a generalized form of the modified Crocco relation, which relates the mean temperature …

Effective Approach For Estimating Turbulence-Chemistry Interaction In Hypersonic Turbulent Boundary Layers, L. (Lian) Duan, M. P. Martín

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An effective approach for estimating turbulence-chemistry interaction in hypersonic turbulent boundary layers is proposed, based on "laminar- chemistry" Reynolds-averaged Navier-Stokes mean flow solutions. The approach combines an assumed probability density function with a temperature fluctuation scaling, which provides the second moment for specifying the shape of the probability density function. As a result, the effects of temperature fluctuation on chemical production rates can be estimated without solving an additional moment evolution equation. The validity of this method is demonstrated using direct-numerical-simulation data. This approach can be used to identify regions with potentially significant turbulence-chemistry interaction in hypersonic boundary layers and …

Effect Of The Thickness Of Undoped Gan Interlayers Between Multiple Quantum Wells And The P-Doped Layer On The Performance Of Gan Light-Emitting Diodes, T. Lu, S. Li, K. Zhang, C. Liu, Y. Yin, L. Wu, H. Wang, Xiaodong Yang, G. Xiao, Y. Zhou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

InGaN based light-emitting diodes (LEDs) with undoped GaN interlayer of variant thicknesses grown by metal-organic chemical vapor deposition technique have been investigated. It was found that the thickness of undoped GaN interlayers affected LEDs' performance greatly. The LED with 50 nm undoped GaN interlayer showed higher light output power and lower reverse-leakage current compared with the others at 20 mA. Based on electrical and optical characteristics analysis and numerical simulation, these improvements are mainly attributed to the improvement of the quality of depletion region by inserting an undoped GaN layer, as well as reduction of the Shockley-Read-Hall recombination in InGaN/GaN …

Advances In Hydrogen Compression Ignition Internal Combustion Engines, Alberto Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The turbocharged direct injection lean burn Diesel engine is the most efficient engine now in production for transport applications within heavy duty trucks applications full load brake engine thermal efficiencies up to 45% and reduced penalties in brake engine thermal efficiencies reducing the load by the quantity of fuel injected. the secrets of this engine's performances are the high compression ratio and the lean bulk combustion mostly diffusion controlled in addition to the partial recovery of the exhaust energy to boost the charging efficiency. the major downfalls of this engine are the carbon dioxide emissions and the depletion of natural …

Stoichiometric H2ice With Water Injection And Exhaust And Coolant Heat Recovery Through Organic Rankine Cycles, Alberto Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

High power density, stoichiometric, turbocharged, directly injected engines with water injection and a three-way catalytic converter after treatment have been proposed as one of the most promising H2ICE [1]. These throttle-controlled engines have top brake efficiencies exceeding 40%, but large penalties in efficiency reducing the load with 1 bar BMEP values approaching 10%. Recovery of the large amount of fuel energy lost in the coolant especially at low loads as well as the fuel energy lost in the exhaust that is significant at high loads and speeds may push not only the top brake efficiencies to exceed the 45% mark, …

Femtosecond Laser Fabricated All-Optical Fiber Sensors With Ultrahigh Refractive Index Sensitivity: Modeling And Experiment, Lan Jiang, Longjiang Zhao, Sumei Wang, Jinpeng Yang, Hai Xiao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

All-optical fiber sensors based on ultracompact fiber inline Mach-Zehnder interferometer (MZI) are fabricated by side-ablating a Ushape microcavity in a single-mode optical fiber with the fiber core partially removed using femtosecond (fs) laser pulses, in which the two light paths are accordingly formed in the remaining D-type fiber core and the U-shape microcavity. Beam propagation method (BPM) analysis is utilized to illustrate the dependences of good transmission spectra on parameters including the ablation depth, ablation length and the refractive index of Ushape microcavity, which gives some guidelines to optimize parameters for fs laser micromachining and predicts RI (refractive index) sensitivities …

A Strategy For Fabricating Complex Structures Via A Hybrid Manufacturing Process, Tarak A. Amine, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The purpose of this paper is to introduce a strategy for fabricating complex structures via a hybrid manufacturing process. The Laser Aided Manufacturing Process (LAMP) lab at Missouri S&T has developed a hybrid process combining both a direct metal deposition process and a five-axis CNC milling. Accessibility is a difficulty when finish machining internal features. The concept is to pause the deposition process to finish machine an internal feature while it is still visible is one possible solution to this issue. However, this must be done in a manner that will not be spoiled when the deposition process continues. This …

Effect Of Particle Size, Binder Content And Heat Treatment On Mechanical Properties Of 13-93 Bioactive Glass Scaffolds, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Particle size, binder content and the post-processing schedule are important parameters that affect the microstructure, and, hence, the mechanical properties of parts produced using the indirect selective laser sintering process. 13-93 bioactive glass, with mean particle sizes ranging from 10 μm to 44 μm, is mixed with different amounts of stearic acid binder to fabricate green scaffolds. Through the design of the post-processing schedule, the time required for postprocessing the green scaffolds is reduced from the initial 80 hrs to 12 hrs. The compressive strength varies from 41 MPa for a part with~60% porosity to 157 MPa for a part …

Bio-Inspired Design Of Bipolar Plate Flow Fields For Polymer Electrolyte Membrane Fuel Cells, Nannan Guo, Ming-Chuan Leu, Maoliang Wu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The flow field of a bipolar plate distributes hydrogen and oxygen for polymer electrolyte membrane (PEM) fuel cells and removes the produced water from the fuel cells. It greatly influences the performance of fuel cells, especially regarding reduction of mass transport loss. Flow fields with good gas distribution and water removal capabilities reduce the mass transport loss, thus allowing higher power density. Inspired by natural structures such as veins in tree leaves and blood vessels in lungs, which efficiently feed nutrition from one central source to large areas and are capable of removing undesirable by-products, a mathematic model has been …

Octree Approach For Simulation Of Additive Manufacturing Toolpath, Ch. Sweta Dhaveji, Todd E. Sparks, Jianzhong Ruan, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Machine simulation is an effective way of checking additive manufacturing tool paths for both interferences and errors in part produced. This paper presents an algorithm to visually simulate a multi axis additive manufacturing system as it executes a process plan. Simulation results are intended to be used as a verification step before physically producing the part. Verification is particularly important for large builds of expensive materials. The algorithm uses an octree approach to efficiently model the deposition of part geometry and its changes. This paper discusses development of the simulation algorithm, including both the representation of the additive manufacturing machine …

Process Planning And Control For Functionally Graded Material Fabrication Using Freeze-Form Extrusion Fabrication, Brad Deuser, Lie Tang, Jeff Geldmeier, Robert G. Landers, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using multiple materials in additive manufacturing technologies is critical for building parts with functionally gradient geometries. In order to achieve a desired material gradient, an advanced process planning and control system is required. This paper details the development of a process planning method and control system for functionally graded material fabrication using a triple extruder Freeze-form Extrusion Fabrication (FEF) system including motion code generation, extruder dynamic modeling and control, and composition gradient control. The effect that extruding multiple materials from a single orifice via static mixing has on the time delay of the resulting mixture is taken into account for …

Freeze-Form Extrusion Fabrication Of Composite Structures, Ming-Chuan Leu, Lie Tang, Bradley K. Deuser, Robert G. Landers, Greg Hilmas, Shi C. Zhang, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Freeze-form Extrusion Fabrication (FEF) process capable of making three-dimensional (3D) parts and structures with graded composite materials is presented in this paper. The process development includes the design and manufacture of a gantry machine with a triple-extruder mechanism and the associated electronics hardware and computer software for fabricating functionally graded parts from multiple aqueous pastes. A rheological behavior study with Al₂O₃ paste is performed to identify an efficient binder for transforming the paste into a pseudoplastic with a high yield stress. A green part is first fabricated using the triple-extruder FEF machine in a layer-by-layer manner …

Numerical Simulation Of Ram Extrusion Process For Ceramic Materials, Mingyang Li, Lie Tang, Fei Xue, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The freeze–form extrusion process for aqueous-based ceramic paste is complex due to the non-Newtonian behavior of the paste. In this paper the process is studied numerically using a developed mathematical model. The ceramic paste viscosity is characterized by the Herschel-Bulkley model. The relationship between plunger velocity and extrusion force is computed numerically. The influence of air, which is mixed with the paste during the loading process, is also examined. Due to the compressibility introduced by the trapped air, the plunger force dynamic response is typically dominated by a first order response. It is also shown that the extrusion plunger force …

Thermal Expansions In Wurtzite Aln, Gan, And Inn: First-Principle Phonon Calculations, L.-C. Xu, R.-Z. Wang, Xiaodong Yang, H. Yan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using the first-principle phonon calculations under the quasiharmonic approximation, thermal expansions in III-nitrides with wurtzite AlN, GaN, and InN are reported. The results showed that it is different for each thermal expansion of three III-nitrides at low temperatures, which is consistent with their Grneisen parameters as the function of temperature. Below 50 K, negative thermal expansions occur in InN, while GaN and AlN follow the rule of positive thermal expansion. To seek the origin of positivenegative thermal expansion distinction, the mode Grneisen parameters and the phonon spectra are investigated. They indicate that different low-frequency phonon vibration modes correspond to the …

Effect Of Molecular Film Thickness On Thermal Conduction Across Solid-Film Interfaces, Zhi Liang, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Brownian Motion and Aggregation of Particles in Nanofluids Often Lead to the Formation of Solid-Film-Solid Structures. the Molecular Thin Film Confined between Nanoparticles May Have Non-Negligible Effects on Thermal Conduction among Nanoparticles. using Nonequilibrium Molecular Dynamics Simulations, We Study Thermal Conduction Across the Ag Particle-Ar Thin-Film Interface. If the Film Contains Only One Molecular Layer, We Find that the Solid-Film Interfacial Thermal Resistance RSF is About 1 Order of Magnitude Smaller Than the Solid-Liquid (Bulk) Interfacial Thermal Resistance RSL. If There Are Two or More Molecular Layers in the Film, It is Shown that RSF Increases Rapidly toward RSL …

Design Optimization Of Gaas Betavoltaic Batteries, Haiyanag Chen, Lan Jiang, Xuyuan Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

GaAs junctions are designed and fabricated for beta voltaic batteries. the design is optimized according to the characteristics of GaAs interface states and the diffusion length in the depletion region of GaAs carriers. under an illumination of 10 mCi cm-263Ni, the open circuit voltage of the optimized batteries is about ∼0.3 V. It is found that the GaAs interface states induce depletion layers on P-type GaAs surfaces. the depletion layer along the P+PN+ junction edge isolates the perimeter surface from the bulk junction, which tends to significantly reduce the battery dark current and leads to a high open circuit voltage. …

The Effect Of On-Line Videos On Learner Outcomes In A Mechanics Of Materials Course, Jeffery S. Thomas, Richard H. Hall, Timothy A. Philpot, Douglas R. Carroll

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Mechanics of Materials course is one of the core engineering courses included in the curriculum of mechanical, civil, mining, petroleum, marine, aeronautical, and several other engineering disciplines. As a core course, the Mechanics of Materials course typically has large enrollment. Initiatives aimed at improving the effectiveness of the engineering core courses can have a major impact on engineering education by virtue of the large number of students affected.

Computers afford opportunities for creative instructional activities that are not possible in the traditional lecture-and-textbook class format. The study described in this paper examines the effectiveness of asynchronous online video that …