Mechanical Engineering Commons^™

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

Experimental Tests And Numerical Simulations For Failure Investigation On Corrugated Boxes Used On Household Appliance Packaging, Diego Fernandes Rodrigues, José Carlos Pereira

Journal of Applied Packaging Research

Packages made of corrugated paper are fundamental to the protection, transportation and handling of the appliance product market. During the storage and sales stages of a product, the package must resist compressive loads in different directions beyond moderate impacts. In this context, the objective of this work is to develop and implement a post-processor that allows the simultaneous analysis of two of the most common failure modes of packages made of corrugated paper: failure due to tensile or compressive stress limit, and failure due to local buckling, when the buckling of the faces of the corrugated paper between two peaks …

Thermophotovoltaic Devices: Combustion Chamber Optimization And Modelling To Maximize Fuel Efficiency, Arnold Chris Toppo, Ernesto Marinero, Zhaxylyk Kudyshev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, 110 billion cubic meters of natural gas (primarily methane), a potent greenhouse gas, are flared off for environmental and safety reasons. This process results in enough fuel to provide the combined natural gas consumption of Germany and France. The research team developed a thermophotovoltaic device to convert thermal energy to electricity at a high efficiency using proprietary emitters and combustion system. With the current focus being fuel efficiency and the combustion process, the assembly was simulated using ANSYS Fluent modelling software and the following parameters were optimized: air/fuel ratios, flow rates, and inlet sizes. Simultaneously the heat transfer across …

Design Survey Of Laminated Composite I-Beam, Mrinmoy Saha

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Composite I-beams are popular for high-strength low-weight applications. Learning the macro-mechanics and designing the composite I-beam properly are necessary. In this report, a design overview of the composite I-beam is discussed which is based on classical lamination theory where it includes the homogenization approach, the plane stress assumption and the Kirchhoff hypothesis. Using these assumptions, a method was developed to come up with the effective material properties of a beam. Formulas to calculate maximum deflection and maximum bending stress and shear stress and the stress concentration at the connection of web-flange are discussed which describe ways for designing and manufacturing …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Microstructural Characterization Of Shear Transformation Zones And Modeling Indentation Size Effect In Amorphous Polymers, Leila Malekmotiei

LSU Doctoral Dissertations

The first aim of this work is developing a procedure for experimental and analytical characterization of nano-scale microstructures which mediate large scale deformation in amorphous polymers. Glassy polymers are extensively used as high impact resistant, low density, and clear materials in industries. Nevertheless, their response under severe loading conditions is yet to be appropriately unraveled. Due to the lack of long-range order in the microstructures of glassy solids, their plastic deformation is different from that in crystalline solids. Shear Transformation Zones (STZs) are believed to be the main plasticity carriers in amorphous solids and defined as the localized atomic or …

Mechanical Characterization Of Selectively Laser Melted 316l Stainless Steel Body Centered Cubic Unit Cells And Lattice Of Varying Node Radii And Strut Angle, Christopher James Hornbeak

Master's Theses

An experimental study of several variants of radius and strut angle of the body centered cubic unit cell was performed to determine the mechanical properties and failure mechanisms of the mesostructure. Quasi static compression tests were performed on an Instron® universal testing machine with a 50kN load cell at 0.2mm/min. The test samples were built using a SLM Solutions 125 selective laser melting machine with 316L stainless steel. Test specimens were based on 5mm cubic unit cells, with a strut diameter 10% of the unit cell size, with skins on top and bottom to provide a cantilever boundary constraint. Specimens …

Composite Suspension For A Mass Market Vehicle, Sarah M. Chapiama, Brian Auyeung, Jose Guerrero, Ethan Lau

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Understanding The Evolution Of Surface Texture Under Boundary Lubrication, Salil T. Bapat

Graduate Theses and Dissertations

The objective of this research was to understand the evolution of surface texture under boundary/mixed lubrication (BL). Significant material/energy losses occur during BL because of direct contact between the two surfaces. Traditionally, tribofilms have been studied extensively for BL while textures have been used as a static engineering design parameter to enhance lubricant film properties. However, texture is dynamic at the tribological mating interface, where both physical and chemical interactions are continuously modulated. The evolution and the interplay between the tribofilm and texture is least studied in the literature, which is the focus of this research.

MoS2-based lubricants, known for …

Hawai'i Wildlife Fund V. County Of Maui, Lowell J. Chandler

Public Land & Resources Law Review

In Hawai’i Wildlife Fund v. County of Maui, the Ninth Circuit held that the plain language of the Clean Water Act provides jurisdiction over indirect discharges of pollutants from a point source into groundwater that is shown to be connected to navigable waters. The court found that studies confirmed pollutants entering the Pacific Ocean were fairly traceable to the County of Maui’s sewage disposal wells. In affirming the district court’s ruling, the Ninth Circuit held that Maui County violated the Clean Water Act by discharging pollutants into a navigable water without the required permit. The court also concluded the …

A Laboratory Kit For Multimeter Design, Seth Percy, Joshua Perry

Thinking Matters Symposium Archive

The multimeter is an important electrical tool and is a combination of many individual instruments. In practice, common multimeter designs are digital and measure voltage, current, resistance, capacitance, etc., using a single set of probes. Before the digital age, the world relied on analog displays. Some argue that analog displays are outdated technology. However, this overlooks one of the most important characteristics provided by the analog display, which is its ability to provide an instantaneous visual perception. Analog displays are currently used for many applications in aviation and automobiles, demonstrating their continuing usefulness in the field. In the multimeter, the …

Manufacturing Process Simulation – On Its Way To Industrial Application, Dennis Otten, Tobias A. Weber, Jan-Christoph Arent

International Journal of Aviation, Aeronautics, and Aerospace

Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview …

Propeller Design Requirements For Quadcopters Utilizing Variable Pitch Propellers, Ian R. Mcandrew, Elena Navarro, Ken Witcher

Publications

Unmanned aerial vehicles, UAV, has increases in the drastically in these past several years since their costs reduced. This research is based and built upon previous research presented in a conference. With the advent of commercial Quadcopters, four propeller systems, are used, being designed and used to operate the advantages of both flight and hovering. The basic design of their propeller blades has not evolved from the early days of manned flight when wooden fixed blades were used. In this paper that expands upon previous findings and discussions it explores the historical developments. Furthermore, how the expansion and reduction in …

Assisted Development Of Mesophase Pitch With Dispersed Graphene And Its Resulting Carbon Fibers, Aaron Owen

Theses and Dissertations--Mechanical and Aerospace Engineering

The efficacy of dispersed reduced graphene oxide (rGO) as a nucleation site for the growth of mesophase in an isotropic pitch was investigated and quantified in this study. Concentrations of rGO were systematically tested in an isotropic petroleum and coal-tar pitch during thermal treatments and compared to pitch without rGO. The mesophase content of each thermally treated pitch was quantified by polarized light point counting. Further characterization of softening temperature and insolubles were quantified. Additionally, the pitches with and without rGO were melt spun, graphitized, and tensile tested to determine the effects of rGO on graphitized fiber mechanical properties and …

Liquid Interaction With Non-Wettable Surfaces Structured With Macroscopic Ridges, Mehran Abolghasemibizaki

Theses and Dissertations

Self-cleaning, anti-corrosion, anti-icing, dropwise-condensation, and drag-reduction are some applications in which superhydrophobic surfaces are implemented. To date, all the studies associated with superhydrophobic surfaces have been dedicated to understanding the liquid interaction with surfaces that are macroscopically smooth. The current study investigates the solid-liquid interaction of such surfaces which are fully decorated with macroscopic ridges (ribbed surfaces). In particular, the drop motion and impact on our newly designed non-wettable ribbed surface have been investigated in this work. Our experimental investigations have shown that liquid drops move faster on the ribbed surfaces due to lower friction induced by such a surface …

Deformation Behavior Of Al/A-Si Core-Shell Nanostructures, Robert Andrew Fleming

Graduate Theses and Dissertations

Al/a-Si core-shell nanostructures (CSNs), consisting of a hemispherical Al core surrounded by a hard shell of a-Si, have been shown to display unusual mechanical behavior in response to compression loading. Most notably, these nanostructures exhibit substantial deformation recovery, even when loaded much beyond the elastic limit. Nanoindentation measurements revealed a unique mechanical response characterized by discontinuous signatures in the load-displacement data. In conjunction with the indentation signatures, nearly complete deformation recovery is observed. This behavior is attributed to dislocation nucleation and annihilation events enabled by the 3-dimensional confinement of the Al core. As the core confinement is reduced, either through …

A Study In The Use Of Elastic Materials In Expandable Containment Units, Andrew J. Eisenman, Joby Anthony Iii, David Satagaj

Montview Journal of Research & Scholarship

The rigidity of materials in conjunction with the aspect of elasticity has been a concern of modern technologies and construction in recent centuries because of the advantages that expandable storage would bring to the fields of containment units with respect to population growth and space exploration. The world population is currently growing at an exponential rate, and as our population grows, the more important it will become to have containment units that can both contain large volumes of material as well as minuscule amounts of material without wasting space. In order accomplish this, we will need a new type of …

Bear Minimum: Ultralight Composite Bear Canister, Rama B. Adajian, Adam C. Eisenbarth

Mechanical Engineering

The ultralight backpacking community needs a strong, easy to use, safe bear canister that is lighter than current market products for trekking in the backcountry. A full design of the lid for the bear canister is to be completed. This includes the locking mechanism to ensure it is bear proof, the interface between the lid and the canister, and the structure of the lid so it passes the strength and weight specifications. The lid, along with the already designed canister body, is to be manufactured with formal documentation. The lid will initially be tested separately and then with the canister …

Investigating The Classical And Non-Classical Mechanical Properties Of Gan Nanowires, Mohammad Reza Zamani Kouhpanji

Electrical and Computer Engineering ETDs

Study and prediction of classical and non-classical mechanical properties of GaN is crucial due to the potential application of GaN nanowires (NWs) in piezoelectric, probe-based nanometrology, and nanolithography areas. GaN is mainly grown on sapphire substrates whose lattice constant and thermal expansion coefficient are significantly different from GaN. These discrepancies cause mechanical defects and high residual stresses and strains in GaN, which reduce its quantum efficiency.

Specifically, for nanoscale applications, the mechanical properties of materials differ significantly compared to the bulk properties due to size-effects. Therefore, it is essential to investigate the mechanical properties of GaN NWs using the non-classical …

Deposition Velocity Dependence On Urban Morphology, Rawand Muzafar Rasheed

Maseeh Summer Undergraduate Research Experience

Understanding the interactions between the atmospheric boundary layer and urban structures provides insights into emerging problems such as green building design as well as dispersion and deposition of pollutants on urban structures. Characterization of deposition velocity dependence through the naphthalene sublimation method on model urban structures is conducted herein where the analogous fundamental transport mechanisms of momentum and mass transport is obtained via mass of naphthalene transferred. Via wind tunnel experiments, results show that deposition velocity of naphthalene from urban structures increases with increased number of urban structures ahead of the point of investigation. This is attributed to the wakes …

Analysis Of Tool Wear And Tool Life Of Cutting Tool Inserts Using Statistical Process Control Charts: A Case Study, Evan R. Ferrell

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Business and Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Evan R. Ferrell on April 28, 2017.

Fabrication And Study Of The Structure And Magnetism Of Rare-Earth Free Nanoclusters, Bhaskar Das

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

No abstract provided.

Negahban Group Report: Saw-Tooth Shear Response Of Aged Poly(Methyl Methacrylate) (Pmma), Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Results for isothermal saw-tooth shear loading experiments conducted on annealed and oven-cooled poly(methyl methacrylate) (PMMA) at temperatures between 50^oC and 140^oC. The experiments were conducted 1996.

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

A Multiscale Model For Damage Progression And Detection In Piezo/Pyroelectric Composite Laminates, Yehia Bahei-El-Din, Amany Micheal

Centre for Advanced Materials

Assessment of damage initiation and progression in composite structures reinforced with electrically active filaments is modelled in a multiscale analysis. The analysis developed is a two-tier, interactive analysis, which involves two length scales; macroscopic, and microscopic. The proposed multiscale analysis provides seamless integration of the mechanics at the two length scales, including piezoelectric and pyroelectric coupling effects and damage under overall thermomechanical loads and an electric field applied to electroactive fibers. The macromechanical analysis is performed for multidirectional, fibrous laminates using the lamination theory, including bending, and the micromechanical analysis is performed using a two-phase model and a periodic array …

Tensile Specimen Punch, John Allen

All Undergraduate Projects

This project comes from a need to have tensile specimens made for the MET 351, Metallurgy/Materials and Processes, and 426, Applied Strengths of Materials, labs. This punch is designed to be used with an arbor press to create the desired tensile specimen shape out of plastic blanks. The initial concept was suggested by Dr. Craig Johnson. The designs went through many changes, for example getting rid of the sides originally proposed to hold the specimen in place, and modifications to other parts to make them more efficient. Additional parts were also added to the design with the help and advice …

Detecting Laminate Damage Using Embedded Electrically Active Plies – An Analytical Approach, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Assessment of damage initiation and progression in composite laminates with embedded electrically active plies is modeled. Utilizing electrically active layers embedded in composite laminates as damage sensors is proposed by several researchers and is mainly assessed experimentally. Sensing damage using embedded electrically active plies is generally preferred over the use of surface mounted PZT wafers since the range of the latter is limited to a very narrow area underneath the surface, while multiple damage mechanisms can generally be found in several plies of the laminate. The solution presented invokes two levels of analysis. Firstly, on the laminate level, applied membrane …

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …

Pore Formation In Aluminum Castings: Theoretical Calculations And The Extrinsic Effect Of Entrained Surface Oxide Films, Pedram Yousefian

UNF Graduate Theses and Dissertations

Aluminum alloy castings are being integrated increasingly into automotive and aerospace assemblies due to their extraordinary properties, especially high strength-to-density ratio. To produce high quality castings, it is necessary to understand the mechanisms of the formation of defects, specifically pores and inclusion, in aluminum. There have been numerous studies on pore formation during solidification which lead to hot tearing and/or reduction in mechanical properties. However, a comprehensive study that correlates pore formation theory with in situ observations and modeling assumptions from the literature as well as experimental observations in not available. The present study is motivated to fill this gap. …

Finite Element Simulation Of Pzt-Aided Interrogation Of Composite Laminates Exhibiting Damage, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Piezoelectricity has proved effective in capturing changes in structures caused by various damage mechanisms. In one approach, piezoelectric wafer active sensors (PWAS) are mounted on the surface of the host structure and utilized as both actuators and sensors to interrogate the structure and monitor its health. This is achieved by subjecting the PWAS to a transient electric pulse and reading the resulting voltage. Changes in the stiffness of the substrate due to structural damage affect the response of the PWAS, which could be correlated to integrity of the structure. Applying this technique to fibrous composite laminates encounters particular challenges due …