Mechanical Engineering Commons^™

Modulating Mechanical Properties Of Polymer Composites Via Colloidal Particle Reinforcement, Yusheng Guo

LSU Master's Theses

Additive manufacturing allows the rapid process of complex objects with excellent design flexibility. However, the products often exhibit poor mechanical properties when pure polymer is applied as printable material. In this work, we demonstrate that printability of polymer can be dramatically improved when particle filler is added to form reinforced polymer composites. Furthermore, the interaction between filler and polymer matrix leads to the enhancement in mechanical properties of the printed product. The material reinforcement induced by addition of fillers enables the wide application of polymer composites to print structures with unique features. In the printing of silica-reinforced pNIPAM composite, we …

Characterization And Performance Of Minimum Quantity Lubricants In Through-Tool Drilling, Amla Patil, Jay Raval, Tim Bangma, Immanuel Edinbarough, Bruce Tai, David Stephenson, Suleiman Obeidat, Wayne Nguyen Hung

Manufacturing & Industrial Engineering Faculty Publications

This study characterized airborne microdroplet diameters and size distribution from two commercially available lubricants A and B for internal minimum quantity lubrication (MQL). The effects of air pressure, oil channel size, physical properties of lubricants on the resultant microdroplets and through-tool MQL drilling performance were studied. Airborne microdroplet diameters were highly sensitive to the coolant channel sizes and air pressure. Cluster method was used to divide microdroplets into smaller clusters for comparison. Experimental data show that the average airborne microdroplet of lubricant B was larger than that of lubricant A at different air pressures and channel sizes. The contact angle …

Impact Of Sintering Time And Temperature On Mechanical Properties In Projection Sintering Of Polyamide-12, Justin Nussbaum, Taranjot Kaur, Julie Harmon, Nathan B. Crane

Faculty Publications

In powder bed fusion additive manufacturing (AM), the fusing process is temperature and time dependent. However, little work has been done to understand how different processing temperatures and times might impact the mechanical properties at longer sintering times than are typical in laser sintering (LS) systems. Prior results with projection sintering have shown that heating for longer times (>1s) improves part toughness compared to laser sintering. In this work, Large Area Projection Sintering (LAPS) is used to sinter entire layers of material simultaneously over the course of a few seconds with spatial control of layer temperature. This work evaluates …

Preparation Characterization And Tribological Behavior Of Lube Oil With Nanoparticles Additives, Waleed Alghani

Student Works (2020-2029)

There are many companies worldwide that would like to improve and upgrade the lube oil and enhance its performance. There is a big concern for the enhancement of lube oil by using nanotechnology and more precisely with using nanomaterial additives. Much work has made to explore and develop new sorts of lubricating oil nano-additives to diminish wear and friction in tribological configurations and to enhance surface morphology. It has noted that the use of dual nano-additives should examine the lubricating capacity and durability of lubricant. (TiO2 Anatase + Graphene) and (ZnO + Graphene) nanoparticles have selected to formulate nano-additives that …

Design Of A Methanol Reformer For On-Board Production Of Hydrogen As Fuel For A 3kw High-Temperature Proton Exchange Membrane Fuel Cell Power System, Vladimir Gurau, Adedayo Ogunleke, F. Strickland

Manufacturing Engineering: Faculty Publications (2015-2023)

The method of Computational Fluid Dynamics is used to predict the process parameters and select the optimum operating regime of a methanol reformer for on-board production of hydrogen as fuel for a 3 kW High-Temperature Proton Exchange Membrane Fuel Cell power system. The analysis uses a three reactions kinetics model for methanol steam reforming, water gas shift and methanol decomposition reactions on Cu/ZnO/Al2O3 catalyst. Numerical simulations are performed at single channel level for a range of reformer operating temperatures and values of the molar flow rate of methanol per weight of catalyst at the reformer inlet. Two operating regimes of …

An Affordable And Portable Palpable System For Sensing Breast Tissue Abnormalities, Cody J. Clarke

Montview Journal of Research & Scholarship

Due to the high cost of equipment and lack of trained personnel, manual palpation is a preferred alternative breast examination technique over mammography. The process involves a thorough search pattern using trained fingers and applying adequate pressure, with the objective of identifying solid masses from the surrounding breast tissue. However, palpation requires skills that must be obtained through adequate training in order to ensure proper diagnosis. Consequently, palpation performance and reporting techniques have been inconsistent. Automating the palpation technique would optimize the performance of self-breast examination, optimize clinical breast examinations (CBE), and enable the visualization of breast abnormalities as well …

Application Of Optimized Laser Surface Re-Melting Process On Selective Laser Melted 316l Stainless Steel Inclined Parts, Jafar Ghorbani, Jianzhi Li, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications

Lower surface quality of selective laser melting (SLM) manufactured parts remains to be a key shortcoming particularly for high performance functional components. In this paper, the authors utilized Box–Behnken methodology to explore the effect of laser surface re-melting process parameters. The process parameters are:laser power, laser exposure time, laser point distance, and shell layer thickness. The experiments were conducted using Renishaw AM-250 machine. SLM manufactured parts with inclination of 45˚ up-skin were treated with a given surface roughness using laser surface re-melting (LSR). The optimization of process parameters was conducted using response surface methodology and the validation tests was carried …

Dynamic Analysis And Fabrication Of A Bi-Stable Structure Designed For Mems Energy Harvesting Applications., Masoud Derakhshani

Electronic Theses and Dissertations

Thanks to the rapid growth in demand for power in remote locations, scientists’ attention has been drawn to vibration energy harvesting as an alternative to batteries. Over the past ten years, the energy harvesting community has focused on bistable structures as a means of broadening the working frequency range and, by extension, the effective efficiency of vibration-based power scavenging systems. In the current study, a new method is implemented to statically and dynamically analyze a bistable buckled, multi-component coupled structure designed specifically for low-frequency vibration energy harvesting systems in both macro and MEMS-scale sizes. Furthermore, several micro-fabrication steps using advanced …

Experimental Study Of Graphene Energy Absorbing Layer In Femtosecond Infrared Laser Assisted Bioprinting, Chaoran Dou

Theses and Dissertations

The bioprinting, as a new branch of additive manufacturing, already shown its potential in organ transplantation, medicine develop and personalized medicine. There are three types of bioprinting: droplet based bioprinting, extrusion based bioprinting and laser assisted bioprinting (LAB). Compared with other types of bioprinting, the LAB is the only bioprinting method that does not have a nozzle, which gives it the ability to print high viscosity bioink. The LAB also enjoys higher resolution and cell viability than other methods.

The bubble/jet formation process is the most important process for the LAB, which deposits the bioink to the substrate. To utilize …

Formula Sae Monocoque Chassis Development, Kc Egger, Brian Ford, Kyle Nagao, Neal Sharma, Donovan Zusalim

Mechanical Engineering

Formula SAE is a collegiate competition hosted by SAE International with the primary goal being to design, manufacture, and race an open wheel race car. The Cal Poly Racing Formula SAE team strives for improvement every race season and has remained competitive as a result. The 2019-2020 management team determined that further research and development towards the chassis would yield the greatest performance benefit for future seasons, as the previous chassis platform limited packaging and mounting options for vehicle subsystems which interfaced with the chassis.

A redesign of the Cal Poly Racing Formula SAE team’s carbon fiber reinforced polymer monocoque …

Comparison Of Pressure-Assist Silver Sintering To Tin Silver Solder Alloy As Die Attach Material In High Power Semiconductor, Tolentino Erik Nino

Student Works (2020-2029)

The research is focused on pressure-assisted silver sintering material that is compared to tin silver solder alloy paste as used in power electronics. Material characterization, electrical tests, and reliability tests were conducted in the experiment. After drying process, it was observed that the Ag sintering paste height was reduced to approximately 40 percent. Die attach shear test showed that the average reading is about from 200 to 600 grams which are already enough to hold the dice before proceeding to the pressure sintering process. X-ray revealed that the void percent for SnAg paste sample is about 1.5 percent while pressure-assist …

Wavelength Decomposition Of Hybrid Additive Manufacturing Power Signals And Their Relationship With Surface Integrity, Xingtao Wang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Additive Manufacturing (AM) has been a promising manufacturing technology in industrial applications and gained a massive amount of attention from researchers all over the world. Directed Energy Deposition (DED) is an AM process in which focused thermal energy is used to fuse materials by melting as they are deposited. One of the most significant challenges involved in current metal AM processes is improving repeatability and consistency. Substantial effort has already been invested in this area of research.

In this dissertation, a milling tool not only played a role in subtractive manufacturing but also acted as a method of monitoring the …

Preventing Delayed Cracks In Sus304 Deep Drawn Cups Using Extreme Blank Holding Forces Aided By Nanolubrication, Ibrahim Muhammad Shafiq

Student Works (2020-2029)

This study was to investigate the formation and reformation of delayed cracks of SUS304 cylindrical drawn cups under elevated blank holding force (BHF) from 8~32 kN with 1~3 wt% SiO2 nanolubricants concentrations. The widest crack-free BHF range i.e. from 29 ~ 31 kN was determined for 2 wt% of SiO2 in the experiment. Delayed cracks were also observed below and beyond this BHF range. There was an increment of frictional force at the cup flange region when entering the crack-free BHF range, as proven by the rebound in sidewall thickness, relative intensity of α′-martensite, elongated height and drawing force beyond …

Microstructural Characteristics And Mechanical Properties Of Sn-Ag-Cu Solders With Minor Additions Of Al And Zn, Yee Mei Leong

Student Works (2020-2029)

Driven by the recent trend towards miniaturization of lead free electronic products, researchers are putting immense efforts to improve the properties and reliability of Sn based solders. Recently, much interest has been shown on low silver (Ag) content solder SAC 105 (Sn-1.0Ag-0.5Cu) solder because of economic reasons and improvement of impact resistance as compared to SAC387(Sn-3.8Ag-0.7Ag). The present work investigates the effect of minor (0.1-0.5wt.%) Aluminium (Al) and Zinc (Zn) addition to SAC105 on the bulk and interfacial structure between solder and copper substrate during reflow and after thermal aging , the mechanical properties of the solder joint and the …

Embedding Computer Simulation Based Classroom Activities To Enhance The Learning Experience For Manufacturing Systems, Tzu-Liang Bill Tseng, Md Fashiar Rahman, Richard Chiou, Ivan Arturo Renteria-Marquez, Aditya Akundi, Amit J. Lopes, Jeevarathinam Senthilkumar

Manufacturing & Industrial Engineering Faculty Publications

In recent time, manufacturing environment are bracing higher end technologies to achieve high productivity, efficiency and effectiveness. Due to the adoption of the sophisticated technologies, the system is becoming very complex and stochastic. Moreover, the manufacturing system is interconnected among its different subsystems and components, which cannot be described only through the theoretical explanation. Here, computer simulation can be integrated to design and visualize the stochastic and complex system. This paper uses the advantage of simulation to describe a series classroom activity using SIMIO software, which are deployed in industrial systems simulation course in the University of Texas at El …

Thermal Conductivity Performance Of 2d Hbn/Mos 2/Hybrid Nanostructures Used On Natural And Synthetic Esters, Jaime Taha-Tijerina, Hélio Ribeiro, Karla Aviña, Juan Manuel Martínez, Anna Paula Godoy, Josué Marciano De Oliveira Cremonezzi, Milene Adriane Luciano, Marcos Antônio Gimenes Benega, Ricardo Jorge Espanhol Andrade, Guilhermino José Macedo Fechine

Manufacturing & Industrial Engineering Faculty Publications

In this paper, the thermal conductivity behavior of synthetic and natural esters reinforced with 2D nanostructures-single hexagonal boron nitride (h-BN), single molybdenum disulfide (MoS2), and hybrid h-BN/MOS2-were studied and compared to each other. As a basis for the synthesis of nanofluids, three biodegradable insulating lubricants were used: FR3TM and VG-100 were used as natural esters and MIDEL 7131 as a synthetic ester. Two-dimensional nanosheets of h-BN, MoS2, and their hybrid nanofillers (50/50 ratio percent) were incorporated into matrix lubricants without surfactants or additives. Nanofluids were prepared at 0.01, 0.05, 0.10, 0.15, and 0.25 weight percent of filler fraction. The experimental …

Feasibility Of Electric Field Assisted Clogging Reduction In Cold Gas Spraying Nozzle, Hendric Tronsson

ENGS 88 Honors Thesis (AB Students)

The relatively novel cold spraying process expands its range of applications constantly. In order to continue this trend, this process still has various hurdles that need to be overcome such as clogging. Clogging within the cold gas spraying process causes porous coatings with less material properties and lower durability; a solution is needed in order to reduce the clogging and so expand the cold gas spraying applications. This study aimed to explore the feasibility of using an electric field to reduce clogging. To do so a simplified channel was used to simulate charged particle trajectory shifts under the influence of …

Heavenly Bodies Rsvp, Justin Tyler Spitzer, Allison Jean Turnbaugh, Jack William Boulware, Braden Alex Lockwood

Mechanical Engineering

The purpose of the Heavenly Bodies RSVP project was to design and fabricate planet props, as well as a mechanism by which they could be raised and lowered in California Polytechnic State University’s Pavilion theater. The project team was comprised of four fourth year mechanical engineering students: Allison Turnbaugh, Braden Lockwood, Jack Boulware, and Justin Spitzer. We conducted extensive research to determine the ideal solution for the design problem brought to us by our sponsor. In our analysis, we discovered that the most important aspects of our design were the absolute reliability of the system, fire retardant material selection, and …

Automated Drone Calibration System, Jackie Kelly Jong-Mee Paik, Zach Nathan Richter, Tyler Wilson Van Den Berg, Ryan Alexander Zhan, Matthew Ward Carlson

Mechanical Engineering

The final design review of the Inspired Flight Calibration Team senior project will detail the process used to complete a verification prototype of a drone calibration device and discuss lessons learned and suggestions for improving this device. Going from brainstorming and conceptual prototyping all the way through verification prototyping and testing, we were able to design a gyroscopic device that met Inspired Flight’s needs for the flight sensor calibration of their drones. The mechanical design involved comprehensive CAD models and hands-on manufacturing. The mechatronics side of the project worked heavily with electrical wiring and writing custom software to communicate and …

Cal Poly Prove Lab Endurance Car Composite Body Paneling Design, Emma Wheelock, Sarah Rutland, Noah Fisher, Brian Menard

Mechanical Engineering

The Cal Poly Prototype Vehicles Laboratory (PROVE Lab) needs a body paneling design for their Endurance Car aeroshell which optimizes strength, weight and accessibility while minimizing complexity. Additionally, a low-complexity, accurate manufacturing process for the PROVE Lab Endurance Car aeroshell needs to be developed. PROVE Lab designed the shape of the aeroshell. The aeroshell will serve to reduce the aerodynamic drag on the car at high speed, and is not a structural component of the car. Due to the high-strength and lightweight nature of composites, PROVE Lab requests the senior project team investigate using composites for automotive body paneling applications. …

Simulating Particle Packing During Powder Spreading For Selective Laser Melted Additive Manufacturing Using The Discrete Element Method In Abaqus, Priscilla Ng

Master's Theses

Metal additive manufacturing allows for the rapid production of complex parts that are otherwise impractical using conventional subtractive manufacturing techniques. Applications for additive manufacturing span across a broad array of industries including aerospace, automotive, and medical, among many others. One metric of printing success is material properties, including part density. While there has been extensive research completed for the density of printed parts, there is little published work concerning powder packing density on the build plate associated with powder spreading.

In this thesis, a Discrete Element Method (DEM) model was created in Abaqus to simulate the spreading behavior of particles …

Rapid Manufacturing Of Critical Industrial Parts: A Method Based On Reverse Engineering, Rapid Prototyping, And Coordinate Metrology, Immanuel Edinbarough, Aditya Akundi

Manufacturing & Industrial Engineering Faculty Publications

This paper presents a method of rapidly manufacturing industrial parts that are critical to the production. In order to assist the Advanced Manufacturing industry, a senior project team at the University of Texas Rio Grande Valley (UTRGV) applied Rapid Manufacturing (RM) to manufacture or fabricate critical machine parts used to maintain production machines. Failures of parts and tools in industrial settings cost money and hurt output. Usually, the problem arises when the tooling being used is one of a kind and repair or replacements come with long leadtimes. Other problems are encountered when original part or tool engineering drawing is …

Text Mining-Based Qualitative Student Assessment Of Interactive Simulation Learning Using Simio Tool – A Work In Progress, Aditya Akundi, Immanuel Edinbarough

Manufacturing & Industrial Engineering Faculty Publications

Computer simulations complement and extend the real-world components of industries and manufacturing organizations. Teaching simulation-based tools helps students in modeling and analyzing the behavior of real time systems. With the increased demand observed in products and technology consumption, manufacturing industries are evolving to embrace new technologies and initiatives. To keep the emerging workforce technically competent in current tools to understand and interpret manufacturing processes, this paper portrays an effort by the authors in introducing SIMIO i.e. a tool on Simulation of intelligent objects to undergraduate students at University of Texas Rio Grande Valley and in understanding the influence of using …

Expanding Engineering And Technology Opportunities To Students In The Border Region Through International Collaboration, Jesus A. Gonzalez-Rodriguez, Immanuel Edinbarough, Adriana Rios-Santiago, Anabel Pineda-Briseno

Manufacturing & Industrial Engineering Faculty Publications

Expanding Engineering and Technology Opportunities to Students in the Border Region through International Collaboration

For some years now, our Department of Engineering Technology of the XXXX, has collaborated with Universities across the southern border to carry out different activities such as undergraduate research, collaborative course-based projects, and senior design projects. We have observed how students benefit from being exposed to work in multidisciplinary and multicultural teams.

We now expand this form of work to a higher-level research collaboration where students and faculty from four different institutions participate. Two institutions of higher education in Mexico and a University and a Community …

Smart Environments For Assisted Living: A Multidisciplinary Collaboration In Engineering And Architecture Education, Adriana Rios-Santiago, Anabel Pineda-Briseno, Jesus A. Gonzalez-Rodriguez, Uriel Saul Huerta

Manufacturing & Industrial Engineering Faculty Publications

This paper presents a description of a collaborative project based on the integration of technology development in the built environment for assisted living. The multidisciplinary collaboration is developed as a cooperative commitment to provide support for cross-border, collective projects. It was initiated as a project-based learning setting between undergraduate engineering students, and four years later the program shifted to include undergraduate architecture students and engineering master’s students. The learning experience opens the gate to a completely new collaborative setting, yet to be established, independent from its predecessor setting of project-based learning, focusing now towards an interdisciplinarity setting in cross-border collaboration. …

Tmtt Chimera Valve Attachment Process, Paulina Nguyen, Devin Debouk, Tamar Kazazian, Noah Thompson

Biomedical Engineering

No abstract provided.

Spring Loaded Camming Device, Jared S. Christner, Kaitlin O. Deherrera, Ryan W. Edwards, John S. Hickey

Mechanical Engineering

Spring loaded camming devices or “cams” are used in traditional rock climbing as a means of active fall protection. Climbers place cams in cracks and fissures in the rock wall. The cam’s lobes press against the walls, locking it in place, anchoring the climber in case of a fall. Currently, there is a lack of large cams on the market. Only two small companies produce cams that are usable in cracks 6.5 inches wide and larger, however their designs are either too heavy and/or lack features to be comfortable. We are a group of mechanical engineering students at Cal Poly …

Modular Cable Buoy, James J. Marinas, Gabriela Vargas, Anthony Catello, Joseph Heald

Mechanical Engineering

Cable terminations are often the least reliable and most expensive components of a maritime system. These cables are suspended in water by a buoy to reduce wear at the terminations. The Naval Information Warfare Center requires a modular auxiliary float with tunable buoyancy that can be placed along such cable. Our system must be able to be deployed, adjusted, and retrieved quickly and easily during operational use. This report focuses on our team’s final design concept and includes all analysis to justify our design direction along with safety, maintenance, and repair considerations. The report further elaborates on cost analysis, manufacture …

Virginia Digital Shipbuilding Program (Vdsp): Building An Agile Modern Workforce To Improve Performance In The Shipbuilding And Ship Repair Industry, Joseph Peter Kosteczko, Katherine Smith, Jessica Johnson, Rafael Diaz

VMASC Publications

Industry 4.0 is the latest stage in the Industrial Revolution and is reflected in the digital transformation and use of emergent technologies including the Internet of Things, Big Data, Robotic automation of processes, 3D printing and additive manufacturing, drones and Artificial Intelligence (AI) in the manufacturing industry. The implementation of these technologies in the Shipbuilding and Ship Repair Industry is currently in a nascent stage. Considering this, there is huge potential to increase cost savings, decrease production timelines, and drive down inefficiencies in Lifecyle management of ships. However, the implementation of these Industry 4.0 technologies is hindered by a noticeable …

Effects Of Powder Recycling In Selective Laser Melting, Nina L. Menon

Industrial and Manufacturing Engineering

The following report analyzes 316L stainless steel powder characteristics of new powder and powder that has been used in the selective laser melting process for 40-50 builds. A literature review was done of powder characteristics, different ways flowability can be tested, and effects of recycling other types of metal powders in Additive Manufacturing. Flowability improved over 21 reuses of the titanium alloy Ti-6Al-4V and resulted in stronger printed parts. Flow of S17-4 PH steel powder was measured with a Hall flowmeter and increased significantly over the course of 10 reuses. Heavily recycled (estimated 50 reuses) 316L SS powder and brand …