Mechanical Engineering Commons^™

Half-Barrel Planter Mover, Mihir Shah, Natalie Lewis, Mason James Hughes

Mechanical Engineering

A device for transporting heavy barrel planters is needed. Barrel planters are wooden wine barrels that have been cut in half along the circumference. They are used to store and grow a variety of plants. As such, they can contain more than 300 pounds of soil. The products currently on the market are not designed for such heavy planters, are cost prohibitive, and do not take advantage of the tapered design of a wine barrel half. A solution is needed that is durable, easy to use, and low cost. This final design report will show the steps used to find …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Project G.H.O.S.T., Matthew Morell, Austin Conrad, Zackeris Gordon, Conan Estes

Mechanical Engineering

Project G.H.O.S.T aimed to produce a model transmission with a control system for high performance/racing electric vehicles to utilize the full capability of the electric motor at higher speed applications. Current electric vehicles have a large amount of torque and use a fixed gear ratio that compromises between both high and low speeds with performance peaking around 65 miles per hour. A typical electric motor used in this application has approximately 1800 ft-lbs of torque up to 5,000 rpm. Past approximately 5,000 rpm, the torque rapidly drops off and so does the overall vehicle performance. Though transmissions exist that could …

Enduro Campers, Ryan J. Shomsky, Alexander W. Horst, Kevin S. Pickering, Jackson L. Aplanalp, Luke Arana, Will Firestone

Mechanical Engineering

The Enduro Campers senior project team (Formerly known as Lobo Campers senior project team) was recruited by Mr. Leif Stein to assist in the design, manufacturing, and testing of the materials and components of his company’s expedition box camper. The two main focuses of the project, divided into two sub-teams, were on the testing and manufacturing process of the materials used in the camper, and on the design and analysis of the camper’s access door, step box, and other subsystems.

The focus of the materials analysis and manufacturing team was based around the design parameter to use composite sandwich panels …

Wind Blade Manufacturing For The Cal Poly Wind Power Club, Benjamin E. Thompson, Jake R. Lund, Claudia C. Angeles

Mechanical Engineering

The Cal Poly Wind Power Club is entering the 2021 Collegiate Wind Competition (CWC) in June. Last year, three senior project teams were assigned to collaborate and assist the club with the pitching mechanism, the rotor balancing, and the manufacturing process. As the manufacturing team, the goal of our project was to design a manufacturing process for the bladegeometry given. The manufacturing process was required to meet the team’s expectations and CWC’s performance requirements to place highly in the competition taking place in June 2021.These expectations included creating a manufacturing process that is repeatable and reliable for future competitions. The …

Asme Rc Baja Racer, Chesna Kern

All Undergraduate Projects

The American Society of Mechanical Engineers (ASME) holds a competition at their annual conference for college students to design an RC car that will compete in sprint, slalom, and obstacle course races. The RC Baja car was designed to complete every event in the competition with a focus on the obstacle course due to the anticipated impacts inflicted on the project car by jumps and other obstacles. The project was a collaborative effort. This presentation focuses on the chassis and suspension while Gizan Gando will present about the drivetrain. The drop and frontal impact test requirements guided the design process …

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …

Balsa Wood Bridge, Anndie Watterson

All Undergraduate Projects

A model for a strong bridge that could span a set distance and rise up to allow for passage underneath was requested, and specifications for the design were given. The model bridge was designed out of balsa wood to meet all the requirements. Using structural and material analysis and simple mechanical designs, a bridge was designed and constructed out of balsa wood, wood glue, and metal components used for articulation that met all of the criteria set by the assigner. The bridge was tested to ensure all specifications were met. The resulting bridge can hold 20kg of weight suspended from …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Asme Rc Baja Car Drivetrain, Gizan G. Gando

All Undergraduate Projects

The purpose of the RC Baja Car is to compete in the American Society of Mechanical Engineers (ASME) competition, a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race. The Slalom is a test in the steering capability of the car. The Drag is a test in the acceleration of the car in a straight line. Lastly, the Baja puts all factors together in a race to test every component of the car. This project is about building an RC car that can function under these conditions and …

Agv Design, Vincent Orzel, Zachary Woodrum

Williams Honors College, Honors Research Projects

This report details the design and calculation work done towards creating an autonomous guided vehicle (AGV) for use in the steel and metal related industries. Steel Equipment Specialists (SES) is a major manufacturer of coil transportation vehicles for these industries. SES believes the future of coil transportation within the mills includes AGVs in some circumstances. The team was tasked with exploring the design and cost of a base model for use in future designs, since SES has not yet modeled or manufactured an AGV. This design was successful under the stress from the application in calculations, and the cost of …

Design, Fabrication, And Testing Of A High-Speed, Low-Cost Atomic Force Microscope Housing And Distance Measurement System, Jonathan Menke

All Undergraduate Theses and Capstone Projects

Advances to the state-of-the-art in fields like biology and material science often stand on the foundation of improved imaging. Here a low-cost Atomic Force Microscope (AFM) housing and distance measurement system was designed, fabricated, and tested. The instrument was developed around an Optical Pickup Unit (OPU) and designed for use as part of a high-speed AFM system. A structure to align the OPU with the probe holder was designed to ensure the beam of the OPU is positioned above the probe in addition to accommodating space, manufacturability, and cost constraints by using cost effective components. The designs were fabricated and …

Energy Consumption And Lifecycle Assessment Comparison Of Cutting Fluids For Drilling Titanium Alloy, Navneet Khanna, Prassan Shah, Jwalant Wadhwa, Anjali Pitroda, Julius M. Schoop, Franci Pusavec

Institute for Sustainable Manufacturing Faculty Publications

This study analyzes four cutting conditions (dry, flood, Liquid CO 2 (LCO2), and Liquid N2 (LN 2)) based on energy consumption and ecological impacts for drilling VT-20, a Titanium alloy. The lower cutting and total energy have been consumed for LCO2 as compared to others. The Life Cycle Assessment (LCA) analysis has been performed using ReCiPe 2016 midpoint (H) to identify the impact of cutting conditions on ecosystem, human health, and natural resources. Cryogenic environment with LN 2 has been found as the most ecological cutting condition next to dry machining, while flood coolant has 94-99% of total impact considering …

The Development Of A Holistic Quality Score Using In-Situ Monitoring Of Laser Powder Bed Fusion, Ryan Daigneault

College of Graduate Studies: Theses & Dissertations

Additive manufacturing processes allow for a great degree of flexibility in terms of part production. The process is autonomous once the part has started printing in that the operator generally does not need to intervene until the part is finished. One issue that this introduces, however, is an inability to determine part quality during the printing process. Once a part has started printing, the operator must either wait until the part is finished or regularly check on the part during the print to determine the part quality. Using data gathered from multiple sensors, a quality score can be used to …

Design And Development Of Soft Earthworm Robot Driven By Fibrous Artificial Muscles, Beau Ragland

College of Graduate Studies: Theses & Dissertations

Earthworm robots have proven their viability in the fields of medicine, reconnaissance, search and rescue, and infrastructure inspection. These robots are traditionally typically hard-shelled and must be tethered to whatever drives their locomotion. For this reason, truly autonomous capabilities are not yet feasible. The goal of this thesis is to introduce a robot that not only sets the groundwork for autonomous locomotion, but also is safe for human-robot interaction. This was done by ensuring that the actuation principle utilized by the robot is safe around humans and can work in an untethered design. Artificial muscle actuation allowed for these prerequisites …

Material Handling System For An Advanced Flexible Manufacturing Environment, Con Cronin

Theses

A Flexible Manufacturing System (FMS) is a method of production that is designed to easily adapt to changes in the type and quantity of the product being manufactured. Machines and computerised systems can be configured to manufacture a variety of parts and to handle the changing levels of production that is required. The aim of this project was to investigate the current manufacturing processes of Kostal Ireland GmbH with the aim of developing a bespoke prototype material handling system to achieve flexible manufacturing. Kostal Ireland GmbH currently do not have the ability to change their manufacturing operations easily when a …

Rheology Of Particulate Suspensions With Non-Newtonian Fluids In Capillaries, Bin Xia, Paul Krueger

Mechanical Engineering Research

This resource contains the processed experimental measurements of the flow consistency index and flow behavior index, along with their trendlines, for the particulate suspensions investigated in "Rheology of Particulate Suspensions with Non-Newtonian Fluids in Capillaries" by Bin Xia and Paul S. Krueger.

Generic Design Methodology For Smart Manufacturing Systems From A Practical Perspective, Part I—Digital Triad Concept And Its Application As A System Reference Model, Zhuming Bi, Wen-Jun Zhang, Chong Wu, Chaomin Luo, Lida Xu

Information Technology & Decision Sciences Faculty Publications

Rapidly developed information technologies (IT) have continuously empowered manufacturing systems and accelerated the evolution of manufacturing system paradigms, and smart manufacturing (SM) has become one of the most promising paradigms. The study of SM has attracted a great deal of attention for researchers in academia and practitioners in industry. However, an obvious fact is that people with different backgrounds have different expectations for SM, and this has led to high diversity, ambiguity, and inconsistency in terms of definitions, reference models, performance matrices, and system design methodologies. It has been found that the state of the art SM research is limited …

Mechanical Properties Of Nanomodified Hybrid Gfrp Composite Materials, Micah Rop Kimutai

College of Graduate Studies: Theses & Dissertations

The mechanical behavior of the nanomodified hybrid epoxy matrix was investigated in glass fiber reinforced plastics (GFRP). In this study, five nanocomposites enriched with as received halloysite, nanomer I.28E, HNT-APTES, and the hybrid combinations of the two HNTs with the nanomer I.28E were successfully fabricated. To evaluate the effects and morphological characteristics of the individual fillers and the hybrid configurations on the epoxy resin matrix, TGA, DSC, and DMA were analyzed. To understand the effect of the five configurations on the neat GFRP laminate, mode I interlaminar fracture toughness, tensile, and vibration properties were investigated. Electron microscopy testing techniques were …

A Machine Vision Based Automated Quality Control System For Product Dimensional Analysis, Aditya Akundi, Mark Reyna

Manufacturing & Industrial Engineering Faculty Publications

Quality control (QC) in manufacturing processes is critical to ensuring consumers receive products with proper functionality and reliability. Faulty products can lead to additional costs for the manufacturer and damage trust in a brand. A growing trend in QC is the use of machine vision (MV) systems because of their noncontact inspection, high repeatability, and relatively low cost. This paper presents a robust MV system developed to perform comparative dimensional inspection on diversely shaped samples, including additive manufacturing products. The algorithm used performs dimensional inspection on a base product considered to have acceptable dimensions. The perimeter, area, rectangularity, and circularity …

A Review On Application Of Model Based Systems Engineering To Manufacturing And Production Engineering Systems, Aditya Akundi, Viviana Lopez

Manufacturing & Industrial Engineering Faculty Publications

Increasing complexity in today’s manufacturing and production industry due to the need for higher flexibility and competitiveness is leading to inconsistencies in the iterative exchange loops of the system design process. To address these complexities and inconsistencies, an ongoing industry trend for organizations to make a transition from document-centric principles and applications to being model-centric is observed. In this paper, a literature review is presented highlighting the current need for an industry-wide transition from document-centric systems engineering to Model-Based Systems Engineering (MBSE). Further, investigating the tools and languages used by the researchers for facilitating the transition to and the integration …

Potential Production Of Theranostic Boron Nitride Nanotubes (64cu-Bnnts) Radiolabeled By Neutron Capture, Wellington Marcos Silva, Helio Ribeiro, Jaime Taha-Tijerina

Manufacturing & Industrial Engineering Faculty Publications

In this work, the radioisotope 64Cu was obtained from copper (II) chloride dihydrate in a nuclear research reactor by neutron capture, (63Cu(n, )64Cu), and incorporated into boron nitride nanotubes (BNNTs) using a solvothermal process. The produced 64Cu-BNNTs were analyzed by TEM, MEV, FTIR, XDR, XPS and gamma spectrometry, with which it was possible to observe the formation of64Cu nanoparticles, with sizes of up to 16 nm, distributed through nanotubes. The synthesized of 64Cu nanostructures showed a pure photoemission peak of 511 keV, which is characteristic of gamma radiation. This type of emission is desirable for Photon Emission Tomography (PET scan) …

Modeling And Optimization Of Process Parameters In Face Milling Of Ti6al4v Alloy Using Taguchi And Grey Relational Analysis, Al Mazedur Rahman, S M Abdur Rob, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications

Titanium alloys are extensively used in aerospace, missiles, rockets, naval ships, automotive, medical devices, and even the consumer electronics industry where a high strength to density ratio, lightweight, high corrosion resistance, and resistance to high temperatures are important. The machining of these alloys has always been challenging for manufacturers. This article investigates the combined effect of radial depth, cutting speed and feed rate on cutting forces, tool life, and surface roughness during face milling of Ti6Al4V alloy. This study focuses on the significance of radial depth of cut on cutting force, tool life and surface roughness compared to that of …

El Español En Estados Unidos Como Recurso Para La Educación De Hispanos En Ingeniería, Hiram Moya

Manufacturing & Industrial Engineering Faculty Publications

Los Hispanos representan la más grande minoría en Estados Unidos. Sin embargo, el número de estudiantes hispanos en las carreras de ciencias y en particular en ingeniería ha estado subrepresentada por muchos años. Esta falta de representación ha hecho que se estudie de muchas formas los métodos de reclutar y retener y graduar estudiantes hispanos en ingeniería. Sin embargo, la urgencia continúa. Existen muchos retos para mejorar la participación de hispanos en ingeniería, incluyendo la falta costumbre en preguntar o solicitar ayuda, los retos económicos, y la falta de ejemplos a seguir en la facultad. Dado los retos, este artículo …

Direct Selective Laser Synthesis Of Cucrfenitial High Entropy Alloy From Elemental Powders Through Selective Laser Melting, Joni Dhar, Lazaro Lopez, Shanshan Zhang, Ben Xu, Mohammed Jasim Uddin, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

This study investigated the synthesis of CuCrFeNiTiAl high entropy alloy (HEA) from pure elements using selective laser melting (SLM). The objectives are to validate the feasibility of the HEA fabrication from elemental powder materials, and to examine the effect of various process conditions in SLM, such as laser power, point distance and laser exposure time, on the microstructures formed. The as-built samples under high, medium and low energy densities were characterized by X-ray diffraction (XRD), and the microstructures were observed using scanning electron microscopy (SEM). The XRD results showed that five major crystal structure phases (hexagonal, monoclinic, orthorhombic, body-centered cubic …

Machine Learning Model Optimization With Hyper Parameter Tuning Approach, Md. Riyad Hossain, Douglas Timmer

Manufacturing & Industrial Engineering Faculty Publications

Hyper-parameters tuning is a key step to find the optimal machine learning parameters. Determining the best hyper-parameters takes a good deal of time, especially when the objective functions are costly to determine, or a large number of parameters are required to be tuned. In contrast to the conventional machine learning algorithms, Neural Network requires tuning hyperparameters more because it has to process a lot of parameters together, and depending on the fine tuning, the accuracy of the model can be varied in between 25%-90%. A few of the most effective techniques for tuning hyper-parameters in the Deep learning methods are: …

Base Vibration Effects On Additive Manufactured Part Quality: A Study Of 3d Printing Onboard U.S. Navy Ships, Nick Jensen

Dissertations, Master's Theses and Master's Reports

The current landscape of manufacturing is evolving because of technology like additive manufacturing (AM). The mobility and compactness of AM are what make it desirable for many industry sectors. The U.S. Navy has shown interest in deploying AM on ships as it could alleviate their dependency on off-route docking to recharge supplies. However, the U.S. Navy's aspiration is currently hindered due to harsh ship-borne environments that degrade AM part quality.

This thesis focuses on vertical base vibration effects on AM part quality. An introduction is first given in Chapter 1 to familiarize the reader with the U.S. Navy's predicament. The …

The Effect Of Laser Welding Modes On Mechanical Properties And Microstructure Of 304l Stainless Steel Parts Fabricated By Laser-Foil-Printing Additive Manufacturing, Chia Hung Hung, Wei Ting Chen, M. Hossein Sehhat, Ming C. Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The success of laser-foil-printing (LFP) additive manufacturing depends critically on the laser welding of sheet metals onto the substrate or the previous layer during the part fabrication process. The welding can be generally categorized into two modes: conduction mode and keyhole mode. In this study, 304L stainless steel parts fabricated by the LFP process using the two laser welding modes are compared. The porosity, microstructure, and tensile properties of the fabricated parts in these two modes are measured and compared in the laser scanning direction (X) and part building direction (Z). The parts fabricated in the conduction mode have a …