Mechanical Engineering Commons^™

Development Of Injection Molding Pressure Monitoring System Using Piezoelectric Sensor, Mostafa Meraj Pasha

Theses and Dissertations

Injection molding is one of the most popular techniques for global plastic production. With this automation technique, the plastic product can be manufactured at a low cost with a complex geometrical shape. A manufacturing process with the high productivity of an injection molding machine depends on molding pressure and temperature inside the mold cavity. In this research, an experimental work is performed to determine a process monitoring system using asynchronous data acquisition, through the incorporation of wired piezo-ceramic sensor to acquire pressure of injection molding system. This piezoelectric sensor is designed in such a way that, a Bluetooth device can …

In-Situ Alloying Of Cucrfenitial High Entropy Alloy Using Spark Plasma Sintering, Yash P. Patil

Theses and Dissertations

Primary objective of this research was to study the correlation between energy parameters (temperature, time and pressure) of spark plasma sintering (SPS) and design/structural properties (uniform distribution of elements, sever lattice distortion, density), indirectly proving consolidation of a stable High-entropy alloy (HEA) that consists of minimum of five elements. Therefore, powders of five principal elements (CuCrFeNiTi) and one minor element (Al) in near equimolar ratios were used for HEA consolidation using SPS but without mechanical alloying. Overall results demonstrated that the HEA was not generated using heterogenous solution of CuCrFeNiTiAl using SPS. This suggests that the mechanical alloying of CuCrFeNiTiAl …

Bioprinting A 3d Tubular Structure With Vascular Smooth Muscle Cells To Observe The Process Compatibility, Taieba Tuba Rahman

Theses and Dissertations

Printability is the ability to print a reproducible structure using the bioprinting technique. Constructing the relationships between printability and printing parameters of the extrusion printing process is difficult because of the presence of too many independent and inter-correlated factors. For this reason, it is necessary to identify and limit the number of significantly influential factors. In addition, Scaffold based blood vessel fabrication is a key challenge in 3D Bioprinting. As vascular smooth muscle cell (VSMCs) is a major component of blood vessels, the investigation of the behavior and orientation of VSMCs after printing is required to better understand the 3D …

Investigation Of Cell Behavior In 3d Printed Lumen Structures For Capillary Regeneration, Victoria Jade Perez

Theses and Dissertations

This thesis work successfully generated a coaxial printing setup and process to generate 3D printed tubules. A dual syringe pump mechanism was developed to print tubular structures to investigate cell behavior with a goal to generate future capillary beds. The mechanism involves the use of collagen–alginate tubules and the use of EDTA to increase the porosity of the tubule structures to study their interaction with media and incubation techniques as well as behavior and morphology. Tubules of 1.7% sodium alginate and 0.4% collagen I reacting with 3.2% CaCl2 solution proved to be more stable in both the printing process and …

A Manufacturing-To-Response Pathway For Formed Carbon Fiber Reinforced Polymer Composite Structures, Madhura Limaye

All Theses

Over the past decade, there has been an increased adoption of thermoplastic and thermoset based continuous carbon fiber reinforced polymer (CFRP) composites for structural applications in several industries. Among the different manufacturing methods, thermoforming process for thermoplastic based continuous CFRP’s offer a major advantage in reducing cycle times for large scale productions. Similarly, out-of-autoclave curing process for thermoset based continuous CFRP’s using heated tooling enables production of large composite structures. However, these manufacturing processes can have a significant impact on the structural performance of parts by inducing undesirable effects. These effects include inhomogeneous fiber orientations, thickness variations, and residual stresses …

Machinability Of Carbon Fiber Reinforced Polymer (Cfrp) Composites: Modeling And Optimization Using Taguchi Analysis And Multi-Objective Genetic Algorithm, S M Abdur Rob

Theses and Dissertations

Carbon Fiber Reinforced Polymer (CFRP) composites have been widely used in aerospace, automotive, nuclear, and biomedical industries due to their high strength to weight ratio, corrosion resistant durability and excellent thermo-mechanical properties in non-oxidative atmospheres. Machining of CFRP composites has always been a challenge for the manufacturers. In this study, turning operation has been performed on CFRP composites to investigate the effects of cutting parameters namely cutting speed, feed rate and depth of cut on the output characteristics including cutting force, surface roughness and tool wear using Taguchi Analysis. Regression Analysis has been used to develop mathematical model for cutting …

Embedded Curriculum With Industry-Recognized Certifications To Improve The Marketability Of Engineering Technology Graduates, Immanuel Edinbarough, Jesus A. Gonzalez-Rodriguez

Manufacturing & Industrial Engineering Faculty Publications

Embedded Curriculum with Industry Recognized Certifications to Improve the Marketability of Engineering Technology Graduates

The Fourth Industrial Revolution is challenging the industries to change the way they manage and operate the manufacturing environment. This leads to the transformation of the world through artificial intelligence, next-generation robotics, automation, big data analytics, 5G technology and Internet of Things. This idea of Industry 4.0 forces the change in the industries of today and tomorrow. In this, cyber physical systems communicate with one another using the Internet of Things. The manufacturing sector takes full advantage of these technologies to produce innovative products to enhance …

An Improved Earned Value Management Method Integrating Quality And Safety, Brian Briggs

LSU Doctoral Dissertations

The construction industry invests significant time and money to improve quality and safety while reducing cost and schedule impacts. The industry has a sincere desire to improve construction project management methods to improve efficiency. Historically, quality and safety underperformances result from undermanaged quality control and safety activities. The cost and schedule impacts associated with poor quality work have always had an impact on construction operations. The unprecedented challenges and uncertainties of COVID-19 highlighted the need to improve the Earned Value Management (EVM) method within construction to reflect these quality and safety activities. The central goal of this dissertation is to …

Study Of Friction And Wear Effects In Aluminum Parts Manufactured Via Single Point Incremental Forming Process Using Petroleum And Vegetable Oil-Based Lubricants, Jose M. Diabb Zavala, Oscar Martinez-Romero, Alex Elias-Zuniga, Hector Manuel Leija Gutierrez, Alejandro Estrada-De La Vega, Jaime Taha-Tijerina

Manufacturing & Industrial Engineering Faculty Publications

This paper focuses on studying how mineral oil, sunflower, soybean, and corn lubricants influence friction and wear effects during the manufacturing of aluminum parts via the single point incremental forming (SPIF) process. To identify how friction, surface roughness, and wear change during the SPIF of aluminum parts, Stribeck curves were plotted as a function of the SPIF process parameters such as vertical step size, wall angle, and tool tip semi-spherical diameter. Furthermore, lubricant effects on the surface of the formed parts are examined by energy dispersive spectroscopy (EDS) and scanning electron microscope (SEM) images, the Alicona optical 3D measurement system, …

An Economical Method For Securely Disintegrating Solid-State Drives Using Blenders, Brandon J. Hopkins Phd, Kevin A. Riggle

Journal of Digital Forensics, Security and Law

Pulverizing solid-state drives (SSDs) down to particles no larger than 2 mm is required by the United States National Security Agency (NSA) to ensure the highest level of data security, but commercial disintegrators that achieve this standard are large, heavy, costly, and often difficult to access globally. Here, we present a portable, inexpensive, and accessible method of pulverizing SSDs using a household blender and other readily available materials. We verify this approach by pulverizing SSDs with a variety of household blenders for fixed periods of time and sieve the resulting powder to ensure appropriate particle size. Among the 6 household …

Mechanical Properties And Microstructure Characteristics Of Alloy Parts Produced By Laser Powder Bed Fusion (Lpbf) Method, Hong Yao

LSU Doctoral Dissertations

Additive manufacturing (AM) is a rapid prototyping technology to produce fully functional and complex designing objects. As one of the AM methods, Laser Powder Bed Fusion (LPBF) has gained the most attention from both academic researchers and industrial companies. During the LPBF process, metal powders are applied layer by layer, which can be 20 microns to 50 microns in thickness. After a layer is prepared, a high-power laser, which is commonly controlled by a scanning head, is used to selectively melt the interested area of a 2D geometry which is designed in a computer aided designing software. LPBF method can …

Reshaping The Landscape Of The Future: Software-Defined Manufacturing, Lei Xu, Lin Chen, Zhimin Gao, Hiram Moya, Weidong Shi

Computer Science Faculty Publications

We describe the concept of software-defined manufacturing, which divides the manufacturing ecosystem into software definition and physical manufacturing layers. Software-defined manufacturing allows better resource sharing and collaboration, and it has the potential to transform the existing manufacturing sector.

Anisotropic Plasticity Modeling Of Thin Sheets And Its Application To Micro Channel Forming Of Steel Foils, Jie Sheng

Mechanical Engineering Research Theses and Dissertations

Thin sheet metals and ultrathin metal foils produced by industrial rolling processes are textured polycrystalline materials and their mechanical behaviors may depend strongly on the orientation of applied loading. Consideration of such plastic anisotropy in advanced modeling of these materials is of the paramount importance in designing optimal manufacturing processes for automotive and other applications using finite element methods. This research addresses several critical issues in anisotropic plasticity modeling and its applications in analyzing micro channel forming of ultrathin stainless-steel foils. An experimental study has first been carried out on the accuracy and sensitivity of measuring the plastic strain ratios …

Printing Quality Improvement For Laser-Induced Forward Transfer Bioprinting: Numerical Modeling And Experimental Validation, Jie Qu, Chaoran Dou, Ben Xu, Jianzhi Li, Zhonghao Rao, Andrew Tsin

Manufacturing & Industrial Engineering Faculty Publications

Laser-induced-forward-transfer (LIFT)-based laser assisted bioprinting (LAB) has great advantages over other three-dimensional (3D) bioprinting techniques, such as none-contact, free of clogging, high precision, and good compatibility. In a typical LIFT based LAB process, a jet flow transfers the bioink from the ribbon to the substrate due to bioink bubble generation and collapse, and the printing quality is highly dependent on the jet flow regime (stable or unstable), so it is a great challenge to understand the connection between the jet flow and the printing outcomes. To tackle this challenge, a novel computational-fluid-dynamics (CFD)-based model was developed in this study to …

A State-Of-The-Art Review Of Laser-Assisted Bioprinting And Its Future Research Trends, Chaoran Dou, Victoria Perez, Jie Qu, Andrew Tsin, Ben Xu, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

Bioprinting is an additive manufacturing technology with great potential in medical applications. Among available bioprinting techniques, laser-assisted bioprinting (LAB) is a promising technique due to its high resolution, high cell viability, and the capability to deposit high-viscousity bioink. These characteristics allow the LAB technology to control cells precisely to reconstruct living organs. Recent developments of LAB technologies are reviewed in this paper, covering various designs of LAB printers, research progresses in energy-absorbing layer (EAL), the physical phenomenon that triggers the printing process in terms of bubble formation and jet development, printing process parameters, and major factors related to the post-printing …

A Kinematic Error Controller For Real-Time Kinematic Error Correction Of Industrial Robots, Mitchell R. Woodside, Joseph Fischer, Patrick Bazzoli, Douglas A. Bristow, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Industrial robots are being used more and more for manufacturing applications that require accuracy beyond what can be obtained from joint measurement. While offline calibration techniques such as volumetric error compensation can be used to correct robot kinematic error, these methods are unable to compensate for robot deformations caused by changing tool loads during the manufacturing operation. This paper explores the use of a real-time robot kinematic error compensation technique where an external high-precision feedback sensor (in this case a laser tracker) directly measures the robot kinematic error and corrections are implemented during processing. A robot kinematic error model is …

Towards Semantic Integration Of Machine Vision Systems To Aid Manufacturing Event Understanding, Kaishu Xia, Clint Saidy, Max Kirkpatrick, Noble Anumbe, Amit Sheth, Ramy Harik

Publications

A manufacturing paradigm shift from conventional control pyramids to decentralized, service-oriented, and cyber-physical systems (CPSs) is taking place in today’s 4th industrial revolution. Generally accepted roles and implementation recipes of cyber systems are expected to be standardized in the future of manufacturing industry. The authors intend to develop a novel CPS-enabled control architecture that accommodates: (1) intelligent information systems involving domain knowledge, empirical model, and simulation; (2) fast and secured industrial communication networks; (3) cognitive automation by rapid signal analytics and machine learning (ML) based feature extraction; (4) interoperability between machine and human. Semantic integration of process indicators is fundamental …

Rattle Detection – An Automotive Case Study, Orla Hartley

International Conference on Lean Six Sigma

This case study showcases the use of statistical tools to develop an objective Squeak and Rattle (S&R) measurement and detection test for End Of Line (EOL) sign off in an automotive manufacturing environment. Audio Induced S&R is an unwanted vibration within the vehicle caused by the sound system, impacting on customer perception of vehicle quality. Testing for S&R in an automotive environment has a key challenge; how to robustly detect a rattle at the EOL and thus prevent plant escapes to the customer. The objective test developed used microphones and analysers in order to replace an e subjective listening test. …

Handling Of Stealthy Sensor And Actuator Cyberattacks On Evolving Nonlinear Process Systems, Henrique Oyama, Keshav Kasturi Rangan, Helen Durand

Chemical Engineering and Materials Science Faculty Research Publications

Cyberattacks on control systems in the chemical process industries cause concern regarding how they can impact finances, safety, and production levels of companies. A key practical challenge for cyberattack detection and handling using process information is that process behavior evolves over time. Conceivably, changes in process dynamics might cause some detection strategies to flag a change in the dynamics as an attack due to the new data appearing abnormal compared to data from before the dynamics changed. In this work, we utilize several case studies to probe the question of what might be the impacts, benefits, and limitations of cyberattack …

Three-Dimensional Laser-Assisted Printing Of Structures From Nanoparticles, Heng Pan, Chinmoy Podder, Wan Shou, Xiaowei Yu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A method for manufacturing a component comprising bombarding nanoparticles in a dispersion with a laser to transform the ligand and cause the nanoparticles to drop out of the dispersion and deposit onto a substrate; and bombarding additional nanoparticles in the dispersion with the laser to transform the ligand and cause the nanoparticles to drop out of the dispersion and deposit onto the nanoparticles previously deposited out of the dispersion.

Cnc Feed Drive Control, Ryan J. Funchess, Caleb P. O'Gorman, Nick J. Desimone, Juan M. Majano, Samuel K. Wong

Mechanical Engineering

This document serves as the Final Design Report (FDR) for a senior project developed by our team: four senior Mechanical Engineering students and one computer engineering student at California Polytechnic State University, San Luis Obispo (Cal Poly). While the project was completed for, and sponsored by, Professor Simon Xing of Cal Poly, the remainder of the university’s controls professors will be indirectly benefited from this project. Our goal was to design and implement a functional CNC Feed Drive to be used for educational demonstrations and data collection. This document discusses our early product research and benchmark goals, which established constraints …

Bull Outdoor Products - Electric Grill, Sofie M. Groberman, Makai J. Baker, James T. Andrews

Mechanical Engineering

Our senior design project team designed, assembled, and tested an outdoor electric grill. The sponsor for our project is Bull Outdoor Products, a high-end outdoor kitchen set, pizza oven, and grill company. We met with our sponsor to discuss project expectations and important product characteristics. We also researched the barbecue market and its customers to determine what grill characteristics are the most important. We learned which engineering specifications needed to be tested and outlined what our goals and overall objectives for this project are. With our background research and overall objectives in mind, we came up with different solutions through …

F34 Beekeeper Assist, Kyle Ladtkow, Javier Guerra, Jose Velazquez, Ryan Heryford

Mechanical Engineering

Alejandro Jauregui is a veteran who now works as a commercial beekeeper. He lost both of his legs during his service. While his current prostheses allow him to fully complete his work, he has found that inspection of the bee boxes causes him severe hip and back pain. Bee box inspection is a critical task for beekeeping, especially since he maintains about 200 hives every day. Our senior project team was tasked with designing and building a device that would help him move the top bee box out of the way to allow for inspection. We performed preliminary research into …

Med-Drop Pill Dispenser, Cole Pike, Taylor Morris, Christopher Bruni, Jose Gomez

Mechanical Engineering

Veterans’ Affairs home care nurses currently spend anywhere from thirty minutes to two hours filling out monthly prescriptions one pill at a time to veterans who are unable to leave their homes. The goal of this project was to create an easy-to-use device that could be left at a patient’s home that nurses could use to quickly and accurately dispense medication into the patient’s monthly pill box.

Adjustable Head Tube Angle Headset, Glenn Petersen, Ben Harper, Josh Martin, Dylan Prins

Mechanical Engineering

This final design review report describes the design, manufacture, and test process of a bicycle headset capable of quickly and easily adjusting the effective head tube angle. The evolution of mountain bike geometry has forced bike designers to compromise between climbing and descending performance when choosing a head tube angle. A headset capable of quickly adjusting the effective head tube angle would allow riders to optimize their bike’s geometry for different stages of riding. This report details the research, idea generation, concept development and selection, design, manufacturing, and testing of our adjustable head tube angle headset.

Adjustable Height Pedestal Grinder Stand, Josef Zagorski, Zachary Wedel, Michael Sitar, Daniel Zevenbergen

Mechanical Engineering

Pedestal grinders are one of the most common machines found in machine shops today. The current industry standard for mounting a grinder is on a fixed single pillar, cast iron pedestal. A fixed pedestal allows for no vertical adjustment for shop users of different sizes and is a safety hazard. This report further defines this problem and proposes an iterative design process to meet the needs and wants of the customer. The adjustable-height pedestal grinder stand Senior Project team used this problem and design process to successfully complete the project within the allotted time. The first major deliverable and milestone …

Sourceamerica Design Challenge Accessible Kitting And Packaging Station, Christopher Wijaya Tan, Keanau Rick Robin, Kyle Huawei Chuang, Ashley Humpal

Mechanical Engineering

This document entails our research, design, proposed development, and testing process for solving the 2020 SourceAmerica collegiate design challenge. Our team, “Just Kitting”, is composed of four Mechanical Engineering students from California Polytechnic San Luis Obispo. The design challenge requires us to create a device that will help improve the quality of life and productivity of people with disabilities working in the kitting and packaging industry. This document includes our background research and information received from various interviews with our sponsor and others who have experience working with disabilities. Using this information, we refined our problem statement to focus on …

Tensile Testing Environmental Chamber – Structural, Michael Ingel, Erik Soldenwagner, Austin Marshall, Lauren Schirle

Mechanical Engineering

Environmental chambers for tensile testing machines are used to study how a multitude of materials behave in extreme temperatures. These chambers provide the necessary information to innovate cutting edge technology for materials in fields such as aerospace. These chambers are often heavy and expensive requiring a significant amount of time and money just in the installation process alone. This report will serve to outline and define the design and fabrication of an environmental chamber, conducted by a team of four senior mechanical engineering students at California Polytechnic State University, San Luis Obispo. The goals of the project include a low-weight …

Unmanned Research Raft, Jacob Davis, Andrew Fleming, Luke Vickerman, Kahye Yu

Mechanical Engineering

This document serves as the Final Design Review report for the design team conducting the research raft design project for Lawrence Livermore National Lab (LLNL). Our team has taken on a project to design a new research raft for LLNL.

The current rafts are suitable, but engineers have modified and altered the rafts to add more features as needed. This has led to a raft that accomplishes mission goals, but still has room for streamlining. The battery technology has also improved. Our goals were to redesign the raft from the ground up, reducing the size and weight. We also wanted …

Inverted Fluorescence Microscope, Matthew B. Pfeiffer, Spencer George Hann, Thomas James Eggenberger, Trevor Lee Blythe

Mechanical Engineering

Team F13 is composed of Trevor Blythe, Spencer Hann, Matthew Pfeiffer, and Thomas Eggenberger. We are all majoring in mechanical engineering and in our final year of study here at Cal Poly San Luis Obispo. This project is a continuation of a 2019-2020 senior project. The previous team designed and built a functioning inverted fluorescence microscope (IFM) from scratch. This device was created as a lab tool for undergraduate students to be able to perform experiments on microfluidic devices constructed in Cal Poly’s Microfabrication Laboratory. Although substantially functional, several design constraints had not yet been met. Our team has improved …