Mechanical Engineering Commons^™

Combustion Dynamics And Heat Transfer In An Ultra Compact Combustor, Brian T. Bohan

Theses and Dissertations

The Ultra Compact Combustor (UCC) is an innovative combustion system alternative to a traditional turbine engine burner with the potential to improve engine efficiency with a reduced combustor volume. The UCC shortens the axial length of the combustor, and therefore reduces engine weight, by burning in an annulus and swirling the reactants in the circumferential direction. These length and weight improvements can directly lead to an increased thrust-to-weight rating of the engine. The present research included five objectives which advanced the UCC concept on four fronts; cooling UCC turbine vanes, advanced computational modeling of UCC systems, system air split control …

Micro Combustion Of Primary Reference Fuels In Narrow Heated Channels, Veerendra Naralasetti

LSU Master's Theses

Conventional fuel testing machines like CFR engines require large quantities of fuel. The current study seeks to overcome this limitation by introducing an alternative method using a microscale combustion reactor which consumes relatively small amounts of fuel (100-250 ml). For this reason, Primary Reference Fuels (PRF’s: volumetric mixtures of n-heptane and iso-octane) which are simple surrogates of gasoline are selected to test using micro reactor. The primary goal is to determine the effectiveness of using the micro reactor setup to differentiate fuels of different octane number. Experiments with stoichiometric PRF/air mixtures are performed inside a cylindrical quartz tube of 1mm …

Waste Heat Recovery From A Vented Electric Clothes Dryer Utilizing A Finned-Tube Heat Exchanger, Abdul Raheem A. Shaik, Stephen L. Caskey, Eckhard A. Groll

The Summer Undergraduate Research Fellowship (SURF) Symposium

Conventional residential clothes dryers continuously vent moist, hot air during the drying process. The vented air leaves the home but still has useful temperature and humidity that could be recovered to offset other heating demands in the home. A study is carried out to quantify the amount of heat extracted from the waste heat stream of a conventional, vented clothes dryer. To extract the heat, a water cooled, fin-and-tube heat exchanger is located within the exhaust duct. A steady state thermodynamic dry coil and wet coil model was built in Engineering Equation Solver (EES). The model accounts for the heat …

Thermophotovoltaic Devices: Combustion Chamber Optimization And Modelling To Maximize Fuel Efficiency, Arnold Chris Toppo, Ernesto Marinero, Zhaxylyk Kudyshev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, 110 billion cubic meters of natural gas (primarily methane), a potent greenhouse gas, are flared off for environmental and safety reasons. This process results in enough fuel to provide the combined natural gas consumption of Germany and France. The research team developed a thermophotovoltaic device to convert thermal energy to electricity at a high efficiency using proprietary emitters and combustion system. With the current focus being fuel efficiency and the combustion process, the assembly was simulated using ANSYS Fluent modelling software and the following parameters were optimized: air/fuel ratios, flow rates, and inlet sizes. Simultaneously the heat transfer across …

Study Of The Effective Thermal Conductivity Of Polymer Composites With Varying Filler Arrangements, Debraliz Isaac Aragones, Rajath Kantharaj, Aaditya Candadai, Amy Marconnet

The Summer Undergraduate Research Fellowship (SURF) Symposium

Alternative thermal management solutions for electronic devices are being widely explored due to the increasing heat concentration that results from shrinking sizes and increasing power of modern electronics. Clearly, there is a need to spread the heat effectively in these systems, and polymer composites can potentially provide high thermal conductivity at low filler fraction while maintaining desirable mechanical properties for electronic packaging. The present study aims to investigate the effective thermal conductivity of various copper filler arrangements in a polymer matrix. The polymer composites are fabricated using laser cut acrylic templates to embed aligned copper rods in epoxy and create …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

3d Numerical Study Of Multiphase Counter-Current Flow Within A Packed Bed For Post Combustion Carbon Dioxide Capture, Li Yang, Fang Liu, Zhengchang Song, Kunlei Liu, Kozo Saito

Mechanical Engineering Faculty Publications

The hydrodynamics within counter-current flow packed beds is of vital importance to provide insight into the design and operational parameters that may impact reactor and reaction efficiencies in processes used for post combustion CO₂ capture. However, the multiphase counter-current flows in random packing used in these processes are complicated to visualize. Hence, this work aimed at developing a computational fluid dynamics (CFD) model to study more precisely the complex details of flow inside a packed bed. The simulation results clearly demonstrated the development of, and changes in, liquid distributions, wetted areas, and film thickness under various gas and liquid …

Transient Heat Storage Systems, Ian M. Sweeney, Brock M. Johnson, Todd K. Lundberg

Mechanical Engineering

Phase change materials (PCM) have many applications in transient cooling systems, including those with high transient heat loads and low duty cycles. These materials allow a system to remain within a narrow temperature range with a relatively low weight compared to conventional heat sinks or high-power cooling systems. This senior capstone project includes the design of a PCM based thermal energy storage system to integrate into an existing cooling loop, as well as a determination of viable PCM’s for the application. This report contains the necessary information to build the test apparatus.

Driver Cooling System, Joseph Fatin Bolous, Jake Donald Deboer, Alvin Theodore Lau

Mechanical Engineering

This document provides our Final Design Review (FDR) for the Driver Cooling System Project. It contains our background research, which includes current product research, technical research, and information on our sponsor’s needs as a customer as well our manufacturing process, test results, and final design. We created a problem statement to define the scope of the project, discuss sponsor and consumer needs and wants, and technical specifications. After brainstorming, we ultimately selected a thermoelectric cooling system (TEC) after presenting our Preliminary Design Report and Critical Design Report. We built the final prototype, as can be seen in the manufacturing plan, …

3-Dimensional Automated Heat Flux Calibration Device, Victor Raul Chacon, David Madison Morrisset, Alex Michael Schnorr, Kevin Scott

Mechanical Engineering

This document aims to describe the problems in current radiant heat source heat flux calibration techniques and the approach our team took to solve them through automation. The following sections outline the basic premise of the problem we addressed and who our end product benefited. The proceeding sections addresses the research that we have performed regarding heat flux measurements and automation. This research includes current solutions – mostly partial solutions for problems that are similar but not exactly like ours. Following the background research, we define objectives, with specific details that outline how we evaluated different possible solutions, and how …

Upgrading The Sr-30 Miniature Turbojet For Adaptable Exhaust, Shannon Ferreira, Erin Mcmurchie, Peter Pratt

Mechanical Engineering

The California Polytechnic State University, San Luis Obispo (Cal Poly, SLO) Aerospace Department is requesting a variable nozzle adaptation for their SR-30 turbojet engine. The nozzle is intended for laboratory use in sophomore and junior level courses to supplement instruction on the effects that exhaust behavior has on the performance of propulsion technologies. Topics covered during a performance study of the SR-30 turbojet engine will include, but are not limited to: Brayton Cycle analysis, turbojet operation in ideal and non-ideal test conditions, instrumentation limitations, and basic nozzle operation. The SR-30 turbojet engine is similar in design and operation to engines …

Heat Flow Characterization Of Speakers, Sabrina M. Gough, Lydia K. Hedge, Nicolas M. Jones

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Bubble Nucleation In Superhydrophobic Microchannels Due To Subcritical Heating, Adam Cowley, Daniel Maynes, Julie Crockett, Brian D. Iverson

Faculty Publications

This work experimentally studies the effects of single wall heating on laminar flow in a high-aspect ratio superhydrophobic microchannel. When water that is saturated with air is used as the working liquid, the non-wetted cavities on the superhydrophobic surfaces act as nucleation sites and allow air to effervesce out of the water and onto the surface when heated. Previous works in the literature have only considered the opposite case where the water is undersaturated and absorbs air out the cavities for a microchannel setting. The microchannel considered in this work consists of a rib/cavity structured superhydrophobic surface and a glass …

Finite-Difference Modeling Of The Batch Process Smoldering Combustion Of Wastewater, Laura H. Kawashiri

Master's Theses

A MATLAB model was developed for the smoldering combustion of wastewater in the context of a decentralized residential wastewater treatment appliance. Data from a batch process sewage smoldering experiment was simulated using implicit finite-difference approximations, assuming one-dimensional transient conductive heat transfer. The time-dependent temperature profiles within the column represented the main parameters of interest and were used to verify recoverable heat energy estimations. Given that the modeling method used for this thesis represents a unique approach, the assumptions and limitations of this model are thoroughly described in the context of reproducing results for other smoldering setups. A lack of convergence …

Thermal Modelling And Validation Of Heat Profiles In An Rf Plasma Micro-Thruster, Alec Sean Henken

Master's Theses

The need and demand for propulsion devices on nanosatellites has grown over the last decade due to interest in expanding nanosatellite mission abilities, such as attitude control, station-keeping, and collision avoidance. One potential micro-propulsion device suitable for nanosatellites is an electrothermal plasma thruster called Pocket Rocket. Pocket Rocket is a low-power, low-cost propulsion platform specifically designed for use in nanosatellites such as CubeSats. Due to difficulties associated with integrating propulsion devices onto spacecraft such as volume constraints and heat dissipation limitations, a characterization of the heat generation and heat transfer properties of Pocket Rocket is necessary. Several heat-transfer models of …

Temperature And Stress Analysis During Tank Decanting And Refilling Process, Zhe Liu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

In the present work, an analytical expression for the temperature distribution of the cross-section of a natural gas transport tank is derived by time-matching Green’s Function method. The tank decanting process can produce a living temperature decrease inside the tank wall while the filling process can produce a large temperature increase. This behavior can cause damage to the inner layer of the tank. The damage occurs in the form of excessive stress in the wall which is combined mechanical stress and thermal stress. Therefore, thermo-elasticity analysis is another objective of the present work. A simplified mechanical model is established in …

Experimental And Numerical Comparison Of Wort Cooling Methods During The Homebrewing Process, Zachary Hammond

Renée Crown University Honors Thesis Projects - All

Homebrewing, the process of making beer for personal consumption, has been legal in the United States since 1978 and allowed beer enthusiasts to experiment with new beer styles at a low cost. Although the procedure is relatively straightforward, it can be very timeconsuming without expensive equipment. The longest step in brewing is wort cooling, where the non-alcoholic beer, or wort, is cooled from boiling temperatures to near room temperature for fermentation. Improper or slow cooling can not only be monotonous but result in contamination or haze in the final product. Wort chillers, which generally cost anywhere from $50 to $500, …

Thermal Removal Of Carbon Dioxide From The Atmosphere: Energy Requirements And Scaling Issues, Ted Von Hippel

Publications

I conduct a systems-level study of direct air capture of CO2 using techniques from thermal physics. This system relies on a combination of an efficient heat exchanger, radiative cooling, and refrigeration, all at industrial scale and operated in environments at low ambient temperatures. While technological developments will be required for such a system to operate efficiently, those developments rest on a long history of refrigeration expertise and technology, and they can be developed and tested at modest scale. I estimate that the energy required to remove CO2 via this approach is comparable to direct air capture by other techniques. The …

Modeling Residual Stress Development In Hybrid Processing By Additive Manufacturing And Laser Shock Peening, Guru Charan Reddy Madireddy

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The term “hybrid” has been widely applied to many areas of manufacturing. Naturally, that term has found a home in additive manufacturing as well. Hybrid additive manufacturing or hybrid-AM has been used to describe multi-material printing, combined machines (e.g., deposition printing and milling machine center), and combined processes (e.g., printing and interlayer laser re-melting). The capabilities afforded by hybrid-AM are rewriting the design rules for materials and adding a new dimension in the design for additive manufacturing paradigm. This work focuses on hybrid-AM processes, which are defined as the use of additive manufacturing (AM) with one …

Investigating Different Modeling Techniques For Quantifying Heat Transfer Through Building Envelopes, Sodiq Akande

Appalachian Student Research Forum

There is interest concerning the energy performance of buildings in the United States. Buildings, whether residential, commercial or institutional, generally underperform in terms of energy efficiency when compared to buildings that are constructed following sustainably and energy efficiency standards. A substantial percentage of energy loss in these buildings is associated with the thermal efficiency of its envelope (exterior walls, windows roof, floors and doors). The objective of this study will evaluate the results of three energy modeling techniques developed to investigate the energy transfer through the envelope of existing campus buildings. The techniques employed are solving the heat transfer calculations …

An Evaluation Of Induction Heating In Healthcare Food Industry, Barrett Alexander Hampton

Masters Theses & Specialist Projects

This thesis addresses the problem healthcare facilities are having in maintaining proper food temperatures while transporting meals to patients after food has left the kitchen area. Induction heat has been a known method for generating heat for many years. The commercial food industry currently uses this technology, which is beginning to appear in the residential sector as well because of developments made by manufacturers. This study focuses on the top commercial brand models of induction heaters and the supporting materials currently used to create heat sources to maintain food temperatures in hospitals and long term care facilities.

The research in …

Computational Methods For Modeling Multicomponent Droplet Vaporization, Alanna Y. Cooney

Master's Theses (2009 -)

Computational fluid dynamics (CFD) models for combustion of multicomponent hydrocarbon fuels must often prioritize computational efficiency over model complexity, leading to oversimplifying assumptions in the sub-models for droplet vaporization and chemical kinetics. Therefore, a computationally efficient hybrid droplet vaporization-chemical surrogate approach has been developed which emulates both the physical and chemical properties of a multicomponent fuel. For the droplet vaporization/physical portion of the hybrid, a new solution method is presented called the Coupled Algebraic-Direct Quadrature Method of Moments (CA-DQMoM) with delumping which accurately solves for the evolution of every discrete species in a vaporizing multicomponent fuel droplet with the computational …

Numerical Simulation Of Heat Transfer And Chemistry In The Wake Behind A Hypersonic Slender Body At Angle Of Attack, Matthew J. Satchell, Jeffrey M. Layng, Robert B. Greendyke

Faculty Publications

The effect of thermal and chemical boundary conditions on the structure and chemical composition of the wake behind a 3D Mach 7 sphere-cone at an angle of attack of 5 degrees and an altitude of roughly 30,000 m is explored. A special emphasis is placed on determining the number density of chemical species which might lead to detection via the electromagnetic spectrum. The use of non-ablating cold-wall, adiabatic, and radiative equilibrium wall boundary conditions are used to simulate extremes in potential thermal protection system designs. Non-ablating, as well as an ablating boundary condition using the “steady-state ablation” assumption to compute …

Heat Transfer Vest, Nicholas Forsgaard

All Undergraduate Projects

The purpose of this report is to document the progression of the authors senior project. . The of that project was the research of Liquid Cooled Garment (LCG) technology, the generation of a novel LCG prototype and the testing of that prototype relative to a commercial benchmark. As such, this report is a complete narrative of the of these tasks, their execution and the underlying assumptions and commentary. The motivation for this report is to satisfy the capstone requirements of the MET program at CWU by documenting the Senior Project and its subordinate tasks. First, the student designed a LCG …

Investigation Of The Performance And Emissions Characteristics Of Dual Fuel Combustion In A Single Cylinder Idi Diesel Engine, Johnnie L. Williams Jr

College of Graduate Studies: Theses & Dissertations

Restrictions in the allowable exhaust gas emissions of diesel engines has become a driving factor in the design, development, and implementation of internal combustion (IC) engines. A dual fuel research engine concept was developed and implemented in an indirect injected engine in order to research combustion characteristics and emissions for non-road applications. The experimental engine was operated at a constant speed and load 2400 rpm and 5.5 bar indicated mean effective pressure (IMEP). n-Butanol was port fuel injected at 10%, 20%, 30%, and 40% by mass fraction with neat ultra-low sulfur diesel (ULSD#2). Peak pressure, maximum pressure rise rates, and …

Pyrolysis Of Fiber-Plastic Waste Blends, Shreyas Kolapkar

Dissertations, Master's Theses and Master's Reports

The main objective of this work is to investigate fast pyrolysis of fiber and plastic feedstocks in order to understand the synergistic effect from their co-pyrolysis. In this on-going work, fiber, plastic and their blend are characterized and pyrolysis oil is produced from them in the fast batch pyrolysis reactor. Based on a heat transfer model it is shown that results of oil produced from batch reactor will be applicable to the continuous paddle reactor. From feedstock characterization, chlorine was observed particularly in the plastic feedstock. Thus, chlorine removal method using torrefaction and high shear mixing was implemented and was …

Electrical Response Of Thermoelectric Generator To Geometry Variation Under Transient Thermal Boundary Condition, Elias Yazdanshenas, Alireza Rezania, Meysam Karami Rad, Lasse Rosendahl

Mechanical & Aerospace Engineering Faculty Publications

A three-dimensional numerical model is applied in this study to illustrate the electrical response of a thermoelectric generator (TEG) during transient heat flux at the hot side. In this work, various types of thermal boundary conditions are considered to evaluate the performance of the TEG. Thus, a TEG under pulsed heat flux is studied numerically, and the numerical model is verified by experimental results. With the consideration of a defined reference geometry, different heat flux frequencies are applied in order to evaluate the corresponding electrical output by the TEG. In addition, variation of the module performance for various TEG leg …

Optimization Of Heat Sinks In A Range Of Configurations., Archibald Allswell Amoako

Electronic Theses and Dissertations

In this study, different heatsink geometries used for electronic cooling are studied and compared to each other to determine the most efficient. The goal is to optimize heat transfer of the heat sinks studied in a range of configuration based on fin geometry. Heat sinks are thermal conductive material devices designed to absorb and disperse heat from high-temperature objects (e.g. Computer CPU). Common materials used in the manufacturing of heat sinks are aluminum and copper due to their relatively high thermal conductivity and lightweight [1]. Aluminum is used as the material for the heatsinks studied in this research project. To …

Ignition Studies Of Oxy-Syngas/Co2 Mixtures Using Shock Tube For Cleaner Combustion Engines, Samuel Barak

Electronic Theses and Dissertations

In this study, syngas combustion was investigated behind reflected shock waves in order to gain insight into the behavior of ignition delay times and effects of the CO2 dilution. Pressure and light emissions time-histories measurements were taken at a 2 cm axial location away from the end wall. High-speed visualization of the experiments from the end wall was also conducted. Oxy-syngas mixtures that were tested in the shock tube were diluted with CO2 fractions ranging from 60% - 85% by volume. A 10% fuel concentration was consistently used throughout the experiments. This study looked at the effects of changing the …