Mechanical Engineering Commons^™

Simulations On Optimization Of Liquid Spray Burners & Operating Parameters, Pallavi Gajjar, Vinayak Malhotra

International Journal of Aviation, Aeronautics, and Aerospace

Spray burners form an essential part of any liquid propulsion system as they are responsible for injecting, atomizing, mixing and combusting the liquid fuel. Spray combustion used in aerospace applications like the liquid rocket engines, gas turbines or any other controlled environment for that matter places a huge emphasis on safe and effective operations. These applications make use of relatively small amounts of propellant volumes to generate enormous amounts of energy through combustion for producing thrust. For such cases involving enormous energy interactions, combustion comes with its own set of challenges. The predominant challenge among them all is that of …

Influence Of Micro-Nucleate Boiling On Annular Flow Regime Heat Transfer Coefficient Values And Flow Parameters – For High Heat-Flux Flow Boiling Of Water, Soroush Sepahyar

Dissertations, Master's Theses and Master's Reports

Analysis of results from steady and steady-in-the-mean high heat-flux (15 - 70 W/cm², with water as working fluid) shear driven annular flow-boiling experiments presented here - and low heat-flux (0.1- 1 W/cm², with FC-72 as working fluid) experiments presented elsewhere – together lead to a key conclusion. The conclusion is that heat carrying nucleation rates go often undetected by the typically used visualization approaches for flow boiling – as such flows often involve µm- to sub- µm scale bubble diameters in millimeter-scale ducts. These nucleation rates play a significant role in most of the so-called convective …

Multi-Scale, Capillary Assisted Copper Surfaces For Enhanced Pool Boiling Heat Transfer Processes, Chetan Agarwal

Dissertations, Master's Theses and Master's Reports

Phase-change heat transfer through pool boiling process offers a promising thermal management solution in applications wherein conventional air or single-phase liquid-based cooling methods prove inefficient such as for high-power electronics. Pool boiling process, which utilizes the latent heat of evaporation, provides a robust and efficient way to efficiently dissipate the excessive heat generated in a small footprint area in particular as seen in CPUs (Central Processing Units), GPUs (Graphics Processing Units), LEDs (Light Emitting Diodes), radars, and other demanding computing, sensing and surveillance electronics. Although boiling process has been studied for over five decades, it has not been yet adapted …

High Injection Pressure Dme Ignition And Combustion Processes: Experiment And Simulation, Xiucheng Zhu

Dissertations, Master's Theses and Master's Reports

With nearly smokeless combustion, Dimethyl Ether (DME) can be pressurized and used as a liquid fuel for compression-ignition (CI) combustion. However, due to its lower heating value and liquid density compared with diesel fuel, DME has a smaller energy content per unit volume. To obtain an equivalent energy content of diesel, approximately 1.86 times more quantity of DME is required. This can be addressed by a larger nozzle size or higher injection pressure. However, the effect of high injection pressure on DME spray combustion characteristics have not yet been well understood. In order to fill this gap, spray and combustion …

Study Of American Wood Pellet Stove Emissions, Sergio Gamarra

All Graduate Theses, Dissertations, and Other Capstone Projects

Problem: The EPA (Environmental Protection Agency) had not specified emissions performance standards for pellet burning stoves. Instead they were lumped in with cordwood burning stoves. IRETI’s decision to pursue this baseline study was guided by Minnesota’s concurrent “2025 Energy Action Plan” and the EPA’s pellet stove testing method development. Wood pellet fuel, a renewable resource, and the technology developed to utilize it for residential heating should be further studied to examine how together they both stand up to newly developed EPA emissions testing methods. This will establish a benchmark for testing American technology, thus guiding IRETI’s efforts of introducing foreign …

Solar Powered Atmospheric Water Generation, Ben Conser

Master’s Theses

Several atmospheric water generation (AWG) system configurations were analyzed to determine the feasibility of AWG as a method to combat water stress. In order to best combat water stress, AWG must be implemented in such a way which minimizes the energetic and monetary cost of water production. Thermodynamic and economic analyses were used to compare the performance of several AWG system configurations. Metrics such as specific energy consumption (SEC) and levelized cost of water (LCOW), which measure the energetic and monetary cost of water production respectively, were used to compare each system. Using this approach, the optimal system configuration was …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Laser Ablation Of Aluminum, Erika Nosal, Zachary Rahe, Arthur Pamboukis

Williams Honors College, Honors Research Projects

The laser ablation of metal carries relevance in a variety of engineering industries. This includes, but is not limited to, processes such as micromachining, or implementation on aircraft weaponry. The latter application is the reasoning for why aluminum is the specific metal in consideration, as it is commonly used for the construction of aircraft components.

The scope of this project was to optimize the energy dispersed through laser ablation on aluminum by mathematical modeling. The transient conduction process in the aluminum was modeled using a 2-dimensional cylindrical coordinate system in both MATLAB and ANSYS/Fluent. These models were adopted to simulate …

Modeling And Control Of Maximum Pressure Rise Rate In Rcci Engines, Aditya Basina

Dissertations, Master's Theses and Master's Reports

Low Temperature Combustion (LTC) is a combustion strategy that burns fuel at lower temperatures and leaner mixtures in order to achieve high efficiency and near zero NOx emissions. Since the combustion happens at lower temperatures it inhibits the formation of NOx and soot emissions. One such strategy is Reactivity Controlled Compression Ignition (RCCI). One characteristic of RCCI combustion and LTC com- bustion in general is short burn durations which leads to high Pressure Rise Rates (PRR). This limits the operation of these engines to lower loads as at high loads, the Maximum Pressure Rise Rate (MPRR) hinders the use of …

Networked Microgrid Optimization And Energy Management, Robert S. Jane

Dissertations, Master's Theses and Master's Reports

Military vehicles possess attributes consistent with a microgrid, containing electrical energy generation, storage, government furnished equipment (GFE), and the ability to share these capabilities via interconnection. Many military vehicles have significant energy storage capacity to satisfy silent watch requirements, making them particularly well-suited to share their energy storage capabilities with stationary microgrids for more efficient energy management. Further, the energy generation capacity and the fuel consumption rate of the vehicles are comparable to standard diesel generators, for certain scenarios, the use of the vehicles could result in more efficient operation. Energy management of a microgrid is an open area of …

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Propagation And Morphology Of Premixed Flames In Obstructed Channels Under Atmospheric And Supercritical Conditions, Abdulafeez Akinola Adebiyi

Graduate Theses, Dissertations, and Problem Reports (ETD)

The understanding of the morphology and propagation of premixed flames in channels is vital for the design and development of efficient propulsion systems requiring high heat release, such as pulse detonation engines, and for resolving accidental fire in industrial conduits. In this work, extensive computational simulation of premixed flames in channels (with rectangular and cylindrical cross sections) with closely packed obstacles are carried out with the goal of providing insights into flame propagation under various conditions which would be invaluable to the development and safety of energy and propulsion systems as well as for the mitigation of accidental fires in …

Scaling Analysis And Experimental Investigation Of A Rotating Detonation Engine, David Thomas Billups

Graduate Theses, Dissertations, and Problem Reports (ETD)

Pressure gain combustion (PGC) technologies, specifically rotating detonation engines (RDEs), are poised to provide the next big leap in gas turbine engine advancement, significantly increasing the thermal. RDEs make use of thermodynamic advantages of isochoric as opposed to isobaric combustion. Theorized to increase thermal efficiency by up to 7% [1], the RDE would have significant impact on reducing anthropogenic carbon emissions. In addition to efficiency gains, the RDE also provides mechanical simplicity and reduced size advantages compared to it’s traditional counterparts and PGC competition.

The United States (U.S.) Department of Energy (DOE) National Energy Technology Laboratory (NETL) maintains and operates …

Computational Design Of Staged Pressurized Oxy-Coal Combustion, Gideon Ozioma Udochukwu

Graduate Theses, Dissertations, and Problem Reports (ETD)

Staged pressurized oxy-coal combustion (SPOC) is nowadays a promising technology to be used for low-cost, low-emission, high-efficiency power generation. The objective of this thesis is to compliment the experiments ongoing at the Washington University, St. Louis (WUSTL) by means of numerical simulations, thereby providing better understanding of the fluid flow, turbulence, combustion characteristics, particle dynamics and heat transfer. Carbon dioxide (CO2) is injected alongside the coal, for its carriage. A small amount of methane (CH4) is also injected alongside the coal to maintain a steady flame. The simulations are performed for a 3D geometry with the following energy source distribution: …

Experimental And Numerical Study Of The Stirling Engine Robust Foil Regenerator, Koji Yanaga

Graduate Theses, Dissertations, and Problem Reports (ETD)

The regenerator is located between the heat accepter and the heat rejecter of the Stirling engine. It works as a thermal energy storage component in the engine. Most of the regenerators are made of woven screen or random fiber. However, the flow going through the woven screen or random fiber is similar to the cylinders in crossflow which has flow separation. To achieve higher engine efficiency, it is required to design a regenerator which has higher convective heat transfer, lower pressure drops. Therefore, a parallel channel regenerator called a robust foil regenerator was designed and manufactured.

In this study, a …

Investigation Of Heat Exchanger Effectiveness Using A Surface Coating Technology, Allen Duffy

Graduate Theses, Dissertations, and Problem Reports (ETD)

Diesel engine manufacturers continue to improve engine performance through increased thermal efficiency and reduced regulated emissions. The aftercooler located between the turbocharger air outlet and intake manifold experiences a wide range of operating conditions. Improving the heat transfer characteristics in the aftercooler can lead towards improved engine performance through increased charge air density. A surface coating has been proposed to enhance the heat transfer characteristics for a marine-based application on the water - side of the heat exchanger. To evaluate the efficacy of the coating, the rate of heat transfer with and without the coating was quantified in a controlled …

Paddle Mixer-Extrusion Reactor For Torrefaction And Pyrolysis, Stas Zinchik

Dissertations, Master's Theses and Master's Reports

This work is focused on the fundamental understanding and the development of paddle mixer reactors (or modified screw augers). This work will contribute to the effort of the thermal conversion of biomass and wastes. We developed and studied two paddle systems (i) 25-mm lab-scale (up to 1 kg/hr) and (ii) 101-mm pilot-scale (up to 100 kg/hr). Thermal behavior of the two systems was studied and it was estimated that the lab-scale system has a high heating rate of up to 530 °C/s. Residence times were thoroughly measured and were determined as a function of rotation frequency and volume fraction. We …

Reduction Of Nox Emissions In A Single Cylinder Diesel Engine Using Sncr With In-Cylinder Injection Of Aqueous Urea, Anthony Timpanaro

UNF Graduate Theses and Dissertations

The subject of this study is the effect of in-cylinder selective non-catalytic reduction (SNCR) of NO_x emissions in diesel exhaust gas by means of direct injection of aqueous urea ((NH₂)₂CO) into the combustion chamber. A single cylinder diesel test engine was modified to accept an electronically controlled secondary common rail injection system to deliver the aqueous urea directly into the cylinder during engine operation.

Direct in-cylinder injection was chosen in order to ensure precise delivery of the reducing agent without the risk of any premature reactions taking place. Unlike direct in-cylinder injection of neat water, …

Numerical Simulations Of Premixed Flames Of Multi Component Fuels/Air Mixtures And Their Applications, Essa Kh I J Salem

Theses and Dissertations--Mechanical and Aerospace Engineering

Combustion has been used for a long time as a means of energy extraction. However, in the recent years there has been further increase in air pollution, through pollutants such as nitrogen oxides, acid rain etc. To solve this problem, there is a need to reduce carbon and nitrogen oxides through lean burning, fuel dilution and usage of bi-product fuel gases. A numerical analysis has been carried out to investigate the effectiveness of several reduced mechanisms, in terms of computational time and accuracy. The cases were tested for the combustion of hydrocarbons diluted with hydrogen, syngas, and bi-product fuel in …

Elevated Temperature Progressive Damage And Failure Of Duplex Stainless Steel, Darren P. Luke

Civil Engineering ETDs

Ductile failure of metals has been the focus of research efforts within academia and industry for many years since it is tremendously important for understanding the failure of structures under extreme loading conditions. However, limited research has been dedicated to elevated temperature ductile failure, which is critical for evaluating catastrophic events such as industrial, structural or shipping vessel fires. A detailed investigation was conducted on the structural response of Duplex Stainless Steel at elevated temperatures. The temperature dependence of elastic modulus, yield strength, ultimate strength, and ductility was measured up to 1000°C and a continuum damage plasticity model was developed. …

Experimental Investigation Into The Effects Of Thermal Recuperation On The Combustion Characteristics Of A Non-Premixed Meso-Scale Vortex Combustor, Seyed Ehsan Hosseini, Evan Owens, John Krohn, James Leylek

Faculty Publications - Mechanical Engineering

In small-scale combustors, the ratio of area to the combustor volume increases and hence heat loss from the combustor’s wall is significantly enhanced and flame quenching occurs. To solve this problem, non-premixed vortex flow is employed to stabilize flames in a meso-scale combustion chamber to generate small-scale power or thrust for propulsion systems. In this experimental investigation, the effects of thermal recuperation on the characteristics of asymmetric non-premixed vortex combustion are studied. The exhaust gases temperature, emissions and the combustor wall temperature are measured to evaluate thermal and emitter efficiencies. The results illustrate that in both combustors (with/without thermal recuperator), …

Portable Thermoelectric Refrigerator, Cassandra Danielle Beck, Ryan Theodore Gelinas, Joshua Michael Dimaggio, Zachary David Wilson

Mechanical Engineering

This project created a versatile thermoelectric refrigerator that can be used via a wall outlet. The product is durable and effective. The refrigerator is functional in any ambient temperature, and uses thermoelectric cooling, and work from a standard 120V power outlet. By understanding existing products’ limitations and strengths, this project produced a product that outperforms what’s currently on the market. Many of the existing products’ operating temperature is dependent on the ambient temperature of the surroundings, which is a large drawback. Additionally, most of them take a long time to reach their lowest temperature, around 3 hours. One team member, …

Optimization Of Analytical Inverse Heat Transfer Recovery Solution, Nathan Schick

Masters Theses

This thesis describes the different methods used when trying to solve inverse heat transfer problems, particularly those involving recovering heat flux. There are currently several techniques to measure the temperature history in an object subjected to heat transfer using various temperature sensors, however these types of sensors are gradually being replaced by Temperature Sensitive Paints (TSP), a technique that is more accurate and provides a better spatial resolution. TSP is a polymer that is applied on a base object. Changes in temperature in the polymer result in variations of the luminescence intensity in the paint. These variations can be captured …

Effect Of Aerogel On The Thermal Performance Of Corrugated Composite Sandwich Structures, Jacob Dillon Chess

Master's Theses

Current insulation solutions across multiple industries, especially the commercial sector, can be bulky and ineffective when considering their volume. Aerogels are excellent insulators, exhibiting low thermal conductivities and low densities with a porosity of around 95%. Such characteristics make aerogels effective in decreasing conductive heat transfer within a solid. These requirements are crucial for aerospace and spaceflight applications, where sensitive components exist among extreme temperature environments. When implemented into insulation applications, aerogel can perform better than existing technology while using less material, which limits the amount of volume allocated for insulation. The application of these materials into composites can result …

Liquid-To-Liquid Low Grade Waste Heat Recovery Using A Two-Channel Loop, Waleed Farwana

Masters Theses

The use of thermoelectric generators (TEGs) for producing electric energy from low grade “waste heat” has been theorized to provide a sustainable and low-cost energy source for electric power plants. The purpose of this study is to model and experimentally validate a TEG device that takes advantage of low grade waste heat (approximately 100-150 degrees Celsius) in liquid form in order to generate power that can be used for various applications in the surrounding environment. This research aims to demonstrate that optimized TEG designs bear the potential to compete with other methods of low grade waste heat energy harvesting in …

Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston

Mechanical Engineering Undergraduate Honors Theses

Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …

Process-Property-Microstructure Relationships In Laser-Powder Bed Fusion Of 420 Stainless Steel., Subrata Deb Nath

Electronic Theses and Dissertations

Laser-powder bed fusion (L-PBF) is an additive manufacturing technique for fabricating metal components with complex design and customized features. However, only a limited number of materials have been widely studied using L-PBF. AISI 420 stainless steel, an alloy with a useful combination of high strength, hardness, and corrosion resistance, is an example of one such material where few L-PBF investigations have emerged to date. In this dissertation, L-PBF experiments were conducted using 420 stainless steel powders to understand the effects of chemical composition, particle size distribution and processing parameters on ensuing physical, mechanical and corrosion properties and microstructure in comparison …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

A Systematic Investigation Of Condensation Heat Transfer Using Asymmetric Micro-Scale Surfaces, Emily Brown

LSU Master's Theses

Asymmetric surfaces been shown to inducing unidirectional motion in the Leidenfrost regime; however, very minimal research has been conducted to investigate whether these surface can enhance condensation through the same means. The investigation of heat transfer of ratchets in condensation is a relatively untapped area of study, specifically ratchets with superhydrophobic properties. Anticipated difficulty lies in creating surfaces features or coatings that retain the ratchets and can adequately sustain optimal wetting state of Cassie-Baxter required to improve heat transfer performance during condensation. This study serves to investigate whether ratchets are a feasible surface feature to enhance condensation heat transfer. First, …

Large Eddy Simulations Of Vertical Jets In Crossflow, Pranaya Pokharel

LSU Doctoral Dissertations

Jets in crossflow (JICF) have applications ranging from oil spill to film cooling of turbine blades. Hence, an understanding of the flow physics is important. The majority of the research has been conducted for low velocity ratios between jet and crossflow with round jets. JICF is demonstrated to behave differently for high velocity ratios and different jet shapes. Circular and rectangular jets are commonly used in aircraft applications. Current study focuses on high velocity ratio JICF issuing from both circular and rectangular exit.

For simulating JICF, an in house code “Chem3D” is used with Large Eddy Simulation (LES) to model …