Mechanical Engineering Commons^™

A Feasibility Study Of Fuel Cell Cogeneration In Industry, Scott B. Phelps, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Up until now, most of the literature on fuel cell cogeneration describes cogeneration at commercial sites. In this study, a PC25C phosphoric acid fuel cell cogeneration system was designed for an industrial facility and an economic analysis was performed. The US DOE Industrial Assessment Center (IAC) database was examined to determine what industry considers a good investment for energy saving measures. Finally, the results of the cogeneration analysis and database investigation were used to project the conditions in which the PC25C might be accepted by industry.

Analysis of IAC database revealed that energy conservation recommendations with simple paybacks as high …

Modeling And Simulation Of Optical Characteristics Of Microelectromechanical Mirror Arrays, Peter C. Roberts

Theses and Dissertations

MEMS (Micro-Electro-Mechanical Systems) micromirror devices can be used to control the phase of a propagating light wavefront, and in particular to correct aberrations that may be present in the wavefront, due to either atmospheric turbulence or any other type of fixed or time and space varying aberrations. In order to shorten the design cycle of MEMS micromirror devices, computer software is developed to create, from MEMS micromirror device design data, a numerical model of the MEMS device. The model is then used to compute the far field diffraction pattern of a wavefront reflected from the device, and to predict the …

Microelectromechanical Isolation Of Acoustic Wave Resonators, James R. Reid Jr.

Theses and Dissertations

Microelectromechainical systems (MEMS) is a rapidly expanding field of research into the design and fabrication of actuated mechanical systems on the order of a few micrometers to a few millimeters. MEMS potentially offers new methods to solve a variety of engineering problems. A large variety of MEMS systems including flip-up platforms, scanning micromirrors, and rotating micromirrors are developed to demonstrate the types of MEMS that can be fabricated. The potential of MEMS for reducing the vibration sensitivity of surface acoustic wave and surface transverse wave resonators is then evaluated. A micromachined vibration isolation system is designed and modeled. A fabrication …

Demonstrating Optical Aberration Correction With A Mems Micro-Mirror Device, Shaun R. Hick

Theses and Dissertations

This research conducted the first demonstrated use of a micro-electro-mechanical structure (MEMS) mirror array to correct a static optical aberration. A well-developed technique in adaptive optics imaging systems uses a deformable mirror to reflect the incident wave front to the imaging stage of the system. By matching the surface of the deformable mirror to the shape of the wave front phase distortion, the reflected wave front will be less aberrated before it is imaged. Typical adaptive optics systems use piezo-electric actuated deformable mirrors. This research used an electrostatically actuated, segmented mirror array, constructed by standard MEMS fabrication techniques, to investigate …

Artificial Cochlea Design Using Micro-Electro-Mechanical Systems, George C. Dalton Ii

Theses and Dissertations

The use of Micro-Electro-Mechanical Systems (MEMS) in the design of an artificial cochlea is investigated in depth. Interdigitated finger (comb), cantilever, bridge, and mirror resonators are presented as possible devices used to implement the artificial cochlea. These resonators are demonstrated to be extremely high Q devices, capable of being tuned with a simple DC bias. This suggests a possible change to existing cochlea models that claim highly complex AC feedback as being responsible for changes in the damping of the basilar membrane. The new cochlea model presented here, using MEMS to approximate the tuning of the basilar membrane, may be …

Structures And Techniques For Implementing And Packaging Complex, Large Scale Microelectromechanical Systems Using Foundry Fabrication Processes, John H. Comtois

Theses and Dissertations

Microelectromechanical Systems, or 'MEMS' is a broad new field of research into devices that range in size from a few microns to a few millimeters. Much of the technology supporting MEMS research is borrowed from the microelectronics industry; so MEMS holds out the promise of batch fabrication of microminiaturized machines that can be easily integrated with electronics. This dissertation research investigated structures and methods for implementing and packaging complex, large scale microelectromechanical devices and systems using commercially available foundry fabrication processes. It specifies methods for creating and packaging large, complex MEM systems, allowing the exploration of new MEMS architectures at …

Investigation Of Electrotribological And Arc Erosion Behavior Of Cu-15vol.%Cr In Situ Composite, Zhongyu Chen

Masters Theses

Electrotribological and arc erosion behavior of Cu-15vol.%Cr in situ composite was investigated in terms of coefficient of friction, interfacial resistance, bulk temperature, and wear rate as a function of normal pressure, sliding speed, and electrical current. Microstructural change due to electrical sliding was studied to understand wear mechanisms. Cu-15vol.%Cr in situ composite was selected in this research because it exhibits an excellent combination of mechanical strength and electrical/thermal conductivity.

It was found that the average coefficient of friction decreased with increasing electrical current under dry electrical sliding. The average coefficient of friction was lower under lubricated electrical sliding than that …

Design, Fabrication, Processing, And Testing Of Micro-Electro-Mechanical Chemical Sensors, Brian S. Freeman

Theses and Dissertations

Chemical microsensors are a new field integrating chemical thin film technology with solid-state fabrication techniques to make devices capable of detecting chemicals in the environment. This thesis evaluated commercially available fabrication processes and numerous sensor designs for working chemical sensors. The commercial processes used were MUMPS for surface micromachined devices and MOSIS for bulk micromachined devices. Overall, eight fabrication runs and 29 different designs were made. Of these designs, two were shown to work effectively. Other designs failed due to fabrication problems and design errors that caused release problems. One design that worked was a surface micromachined chemoresistor with interdigitated …

Design, Fabrication And Characterization Of Micro Opto-Electro-Mechanical Systems, Darren E. Sene

Theses and Dissertations

Several micro-opto-electro-mechanical structures were designed using the Multi-User MEMS Process (MUMPS). Specific design techniques were investigated for improving the capabilities of elevating flip up structures. The integration of several flip up microoptical structures into a microoptical system was explored with emphasis on the development of a microinterferometer. The thermal effects on the Modulus of Elasticity were determined by detecting the resonant frequency for a square Flexure Beam Micromirror Device. The resonance of the device was found to match theory to within 0.1 % and the Modulus of Elasticity was found to decrease by 0.041 GPa/K from 290 to 450 K. …

Design And Fabrication Of A Micromechanical Gyroscope, Richard M. Kuhns

Theses and Dissertations

Both size and cost of mechanical and optical inertial navigation systems (INS) have prevented their use in many applications. By developing a micromachined gyroscope and combining it with existing micromachined accelerometer designs to form a low sensitivity INS, the cost would be reduced by a factor of 10 or more. The lower per unit cost would open new areas for INS use. A second advantage of the micromachined INS would be its size. A micromachined INS would weigh only a few ounces and take significantly less space, allowing more room for electronics and the weight reduction would lead to longer …

Design And Development Of Microswitches For Micro-Electro-Mechanical Relay Matrices, Mark W. Phipps

Theses and Dissertations

Many different micro-electro-mechanical switches were designed in the Multi-User MEMS processes (MUMPs) and deep x-ray lithography and electroforming (LIGA) processes. The switches were composed of actuators that operated based upon either electrostatic forces or thermal forces. A thermally activated beam flexure actuator that operated based upon differential heating was used extensively. This actuator, which was fabricated in the MUMPs process, was able to deflect up to 12 microns with a total input power of less than 25 mW. The thermal resistance, which was needed to model this actuator, was determined from a material constant, 1.9 ± 0.08 m^1.5-°C-W …

A Magnetic Suspension System With A Large Angular Range, Colin P. Britcher, Mehran Ghofrani

Mechanical & Aerospace Engineering Faculty Publications

In order to explore and develop technology required for the magnetic suspension of objects over large ranges of orientation, a small-scale laboratory system, the large-angle magnetic suspension test fixture (LAMSTF) has been constructed at NASA Langley Research Center. This apparatus falls into the category of large-gap, actively stabilized magnetic levitation systems. The hardware comprises five conventional electromagnets in a circular arrangement, each driven from a separate bipolar power amplifier. Electromagnet currents are commanded by a digital control system, implemented on a microcomputer, which in turn derives the position and attitude of the suspended element from an infrared optical system. The …

Computer Data Acquisition, Control, And Analysis For The University Of Tennessee At Chattanooga's Internal Combustion Engine Labratory, Ahmad Noureddine

Masters Theses and Doctoral Dissertations

For any data acquisition instrumentation, it is essential to have a voltage or current signal output from any transducer that needs to be monitored.Nine OMEGA thermocouples were installed on the Ford engine-Megatech dynamometer system to monitor the temperature of the exhaust gases at different locations and the coolants entering and leaving the dynamometer and the radiator.Those thermocouples have an output signal of O - 55 mv.The TESCOM gas analyzer system measures the concentrations of the different gases present in the exhaust system of the engine and produces an analog output signal (0 - 100 mv) that is used for data …

Electric Power Transmission & Purchases : Report Of A Study By The Joint Standing Committee On Utilities, 112th Maine Legislature, Maine. Legislature. Joint Standing Committee On Utilities

Maine Collection

Electric Power Transmission & Purchases : Report Of a Study By the Joint Standing Committee on Utilities, 112th Maine Legislature

Maine Legislature. Joint Standing Committee on Utilities.

Augusta, Maine (December 2, 1986).

Contents: Introduction / Issues & Recommendations / Review of 1986 Legislation / Maine's Electric Power Picture / Technical Analysis of Transmission & Wheeling / Economic Implications of Transmission & Wheeling /. Legals Analysis of Transmission & Wheeling / Proposed Legislation / Appendices / Tables & Figures

Electronic Control Of Electric Motors, Armando Castillo

Graduate Research Papers

The purpose of this study was to investigate the theoretical information on electronic control of electric motors as well as the current state-of-the-art on this topic. It was also intended to carry out some of the experimental circuits discussed, for future instructional situations.

Optimum Use Of Induction Motors In Tanzanian Industries, M. G. Hassanali Jr

Tanzania Journal of Engineering and Technology (TJET)

Abstract

Effect Of Unbalanced Voltage Of Operation Of Polphase Induction Motor Part Ii, H Kabisama

Tanzania Journal of Engineering and Technology (TJET)

During the assessment of the manuscript, it was observed that the paper does not include an abstract. The document proceeds directry to the main content without providing a separate abstract that summarize the study's objectives, methodology, key findings and conclusions

Some Facts And Prospects For The Establishment Of Television Broadcasts In Mainland Tanzania, H. R. Mgombelo

Tanzania Journal of Engineering and Technology (TJET)

Abstract

Multiregional Interactions Between Energy And Transportation, Karen R. Polenske

Applications

Because of the number and complexity of the issues that will determine the use of coal by the electric-generating plants, an important asset of policy makers will be the availability of a method of analysis that allows for quick studies of many different combinations of assumptions and policies. The present prototype study is designed to show how the multiregional input-output model can be used to investigate each different assumption and policy alternative. For this paper, the analysis has necessarily been restricted to two issues. First, the results of using regional rather than national technologies in the model are assessed. This …

A Theory On Interpreting Engine Noises, Robert C. Erickson

Undergraduate Student Work

Mechanics have always used sounds to "trouble shoot" an engine. To a trained ear, each sound is different. Since an ear can be this sensitive, this paper will attempt to prove that electronic equipment can be considerably more accurate in detecting engine problems. The writer of this paper has attempted a project in which he hopes to prove that valve and bearing problems can be located by studying oscilloscope displays. These displays would picture the sound frequencies of valve and bearings in operation. The writer assumed that a comparison could be made of the displays of a normal engine operation …

Australian Tractor Test Report No. 53 : Chamberlain Countryman 354, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

AUSTRALIAN TRACTOR TEST REPORT

No. 53 - CHAMBERLAIN COUNTRYMAN 354

THE Chamberlain Countryman 354 is a broad-acres cultivation tractor of 77 drawbar horsepower with 87 h.p. at the P.T.O.

Australian Tractor Test Report No. 52 : Chamberlain Champion 306, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

AUSTRALIAN TRACTOR TEST REPORT

No. 52 - CHAMBERLAIN CHAMPION 306

THE Chamberlain Champion 306 is a general purpose farm tractor of 57 drawbar horsepower with 68 h.p. at the P.T.O.

The Theory Of The Impulse Function For Oscillatory Mechanical And Electrical Systems, E. L. Hill

Journal of the Minnesota Academy of Science

No abstract provided.

A Study Of Five Commercial Electric Stoves, A. E. Baragar, Edna B. Snyder

Nebraska Agricultural Experiment Station: Historical Research Bulletins

Five commercial electric stoves having major variations in types of surface units, in the construction, lining, and insulation of the oven, and in the retail price were studied to determine (1) the efficiency and time of heating of the various surface units, and (2) the merits of differently constructed ovens.

Test Of A 25 K. W. Dynamo In Use At The Rhode Island College, Merril Agustus Ladd

Student and Lippitt Prize Essays

Defines functions and types of dynamos, with a particular focus on the evaluation a 25 K.W. dynamo, in use at the Rhode Island State College (now URI).