Mechanical Engineering Commons^™

Towards Sustainable Production Of Chemicals And Fuels From The Fast Pyrolysis Of Waste Polyolefin Plastics, Ulises Gracida Alvarez

Dissertations, Master's Theses and Master's Reports

The increasing amount of plastic waste (PW) generation has become an important concern due to the leveled-off recycling rates. Therefore, governmental agencies around the world, including state governments in the United States, have proposed initiatives to minimize the amount of PW that is landfilled and encourage recycling or energy recovery. Circular economy is a strategy that attempts on reusing PW to produce new polymers while avoiding its disposal and the use of virgin material. Chemical recycling raises an interesting technology prospect due to the potential reduction of pollutant emissions and the establishment of a circular economy through the production of …

3d Printing In Low Resource Healthcare Settings: Analysis Of Potential Implementations, Alenna Beroza

Dissertations, Master's Theses and Master's Reports

3D printing has gained significant momentum in the past ten years, and its unique advantages make it especially ideal for use in low resource healthcare settings, where many designs have already been successfully implemented. Yet, little has been studied on how 3D printing can be sustainably and functionally implemented in low resource healthcare systems as a manufacturing practice. In this report, three business models are proposed for this implementation: In-House Operator, Independent Operator, and Print Farm. These models were then tested over four months in Kisumu county, Kenya, at two workshops and seven public hospitals. I worked with local medical …

Crack Pattern Simulation Of Pressurized Borosilicate Glass Tube Under Pellet Impact Using Ale Method, Omkar Bhumkar

Dissertations, Master's Theses and Master's Reports

Transformer bushings are a common target for sniper attacks to cause power failure in large areas. Given the size, internal pressure and brittle nature of transformer bushing, pellet impact causes damage to surrounding components due to broken bushing pieces. To mitigate this, a project was initiated by United States Burau of Reclaimation to develop a safety mechanism. Finite Element Analysis is proposed to optimize and reduce cost of the design.

A simplified Finite Element model is created which consists of 0.22 caliber lead pellet impacting Pyrex 7740 borosilicate glass tube. Previous studies on the effect of the mesh pattern, size …

Applied Deep Learning In Orthopaedics, William Stewart Burton Ii

Electronic Theses and Dissertations

The reemergence of deep learning in recent years has led to its successful application in a wide variety of fields. As a subfield of machine learning, deep learning offers an array of powerful algorithms for data-driven applications. Orthopaedics stands to benefit from the potential of deep learning for advancements in the field. This thesis investigated applications of deep learning for the field of orthopaedics through the development of three distinct projects.

First, algorithms were developed for the automatic segmentation of the structures in the knee from MRI. The resulting algorithms can be used to accurately segment full MRI scans in …

Virtual Morphology As A Method Of Robotic Control, Conner Todd Castle

Graduate Theses, Dissertations, and Problem Reports (ETD)

This thesis presents Virtual Morphology (VM), a method that explores a different perspective on the design of robot autonomy using inspiration from morphological computing and programmed computation. Morphological computation offers physical solutions that solve complex tasks, like robotic grasping of unknown objects, with relative ease. Unfortunately, these physical solutions are difficult to adjust post-development, and are usually designed to complete only one or a few specific tasks. Programmed computational approaches are more flexible because they can be implemented and adjusted through software, but unfortunately, these approaches can become rather complex as tasks become more difficult. This thesis explores the potential …

Computational Study Of Flow Interactions Over A Close Coupled Canard-Wing On Fighter, Setyawan Bekti Wibowo, Sutrisno Sutrisno, Tri Agung Rohmat

International Journal of Aviation, Aeronautics, and Aerospace

There have been many attempts to improve the flying performance of a fighter. By modifying the flow that occurs along the fuselage is expected to improve the performance of the aircraft. One of the indicators of combat aircraft performance is the ability to perform maneuver movement. Adding a canard as forewing on the fighter wing configuration is considered capable of raising the ability in maneuver movement. The use of canard-delta pairs will affect the performance and aerodynamic characteristics of the plane. Wings and canards with delta configuration will make the rolled-up vortex as a lifting force producer on the aircraft. …

Optimizing Nasal Cannulas For Infants Using Computational Fluid Dynamics, Ahmad El-Achwah Mr.

Theses and Dissertations

Aerosolized medications can potentially be delivered to the lungs of infants through a nasal cannula interface. However, nose-to-lung delivery technologies currently allow for ~1% of the loaded dose to reach an infant’s lungs. Conventional dry powder inhalers (DPI) are superior to other types of inhalers in many ways. However, passive DPIs that operate based on user inhalation and require large volumes of airflow are not applicable to infants. To overcome this challenge, positive pressure DPIs have been developed that enable aerosol delivery to infants. Unless an adequate nasal interface is used with these devices, a significant amount of drug will …

A Review Of 3d Gis For Use In Creating Virtual Historic Dublin, Alain Chenaux, Maurice Murphy, S. Pavia, S. Fai, T. Molnar, John Cahill, Shane Lenihan, A. Corns

Conference papers

This paper illustrates how BIM integration with GIS is approached as part of the workflow in creating Virtual Historic Dublin. A design for a WEB based interactive 3D model of historic buildings and centres in Dublin City (Virtual Historic Dublin City) paralleling smart city initiates is now under construction and led by the National Monuments at the Office of Public Works in Ireland. The aim is to facilitate the conservation and maintenance of historic infrastructure and fabric and the dissemination of knowledge for education and cultural tourism using an extensive Historic Building Information Model. Remote sensing data is now processed …

Landing-Gear Impact Response: A Non-Linear Finite Element Approach, Tuan H. Tran

UNF Graduate Theses and Dissertations

The primary objective of this research is to formulate a methodology of assessing the maximum impact loading condition that will incur onto an aircraft’s landing gear system via Finite Element Analysis (FEA) and appropriately determining its corresponding structural and impact responses to minimize potential design failures during hard landing (abnormal impact) and shock absorption testing. Both static and dynamic loading condition were closely analyzed, compared, and derived through the Federal Aviation Administration’s (FAA) airworthiness regulations and empirical testing data.

In this research, a nonlinear transient dynamic analysis is developed and established via NASTRAN advanced nonlinear finite element model (FEM) to …

Feasible Form Parameter Design Of Complex Ship Hull Form Geometry, Thomas L. Mcculloch

LSU New Orleans Theses and Dissertations

This thesis introduces a new methodology for robust form parameter design of complex hull form geometry via constraint programming, automatic differentiation, interval arithmetic, and truncated hierarchical B- splines. To date, there has been no clearly stated methodology for assuring consistency of general (equality and inequality) constraints across an entire geometric form parameter ship hull design space. In contrast, the method to be given here can be used to produce guaranteed narrowing of the design space, such that infeasible portions are eliminated. Furthermore, we can guarantee that any set of form parameters generated by our method will be self consistent. It …

Dynamic Response Of A Hingeless Helicopter Rotor Blade At Hovering And Forward Flights, Pratik Sarker

LSU New Orleans Theses and Dissertations

The helicopter possesses the unrivaled capacity for vertical takeoff and landing which has made the helicopter suitable for numerous tasks such as carrying passengers and equipment, providing air medical services, firefighting, and other military and civil tasks. The nature of the aerodynamic environment surrounding the helicopter gives rise to a significant amount of vibration to its whole body. Among different sources of vibrations, the main rotor blade is the major contributor. The dynamic characteristics of the hingeless rotor consisting of elastic blades are of particular interest because of the strongly coupled equations of motion. The elastic rotor blades are subjected …

A Generative Statistical Approach For Data Classification In A Biologically Inspired Design Tool, Marvin Manuel Arroyo Rujano

Graduate Theses and Dissertations

The objective of the research this thesis describes is to find a way to classify text-based descriptions of biological adaption to support Biologically Inspired design. Biologically inspired design is a fairly new field with ongoing research. There are different tools to assist designers and biologists in bio-inspired design. Some of the most common are BioTRIZ and AskNature. In recent years, more tools have been proposed to aid and make research in the field easier, for example, the Biologically Inspired Adaptive System Design (BIASD) tool. This tool was designed with the goal of helping designers in early design stages generate more …

The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley

Graduate Theses and Dissertations

In the realm of additive manufacturing there is an increasing trend among makers to create designs that allow for end-users to alter them prior to printing an artifact. Online design repositories have tools that facilitate the creation of such artifacts. There are currently no rules for how to create a good customizable design or a way to measure the degree of customization within a design. This work defines three types of customizations found in additive manufacturing and presents three metrics to measure the degree of customization within designs based on the three types of customization. The goal of this work …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

Daimscale — 1:14th Tractor-Trailer For Testing Driver Assistance Technology, Christopher Marrale, Jase Sasaki, Devin Bodmer

Mechanical Engineering

Active driver assistance systems are becoming increasingly wide-spread throughout the automotive industry due to their potential for safer roads and decreased costs of transportation, but testing these systems on real trucks can be time consuming, dangerous, and costly. Testing these systems on a small-scale tractor-trailer combination will lead to faster and more efficient development of driver assistance systems and can be used by both engineers and students, leading to a larger field of experienced developers to improve these systems.

Our goal will be to design, manufacture, and build a scale 6x2 model of the tractor portion of a Daimler semi-truck …

Engineering Success On The Field: A Reflection On The Epics Ironman Pediatric Prosthetic Project, Glynn Gallaway

Purdue Journal of Service-Learning and International Engagement

Glynn Gallaway is a student in the Purdue Mechanical Engineering Class of 2020 with interests in the health care, assistive technology, and medical device industries. Glynn is from Dallas, Texas, and was inspired to pursue this career path through her interactions with youth with special needs. She joined the EPICS Ironman team in the fall of 2016 during her first year at Purdue as a part of the learning community. In this article, she discusses her experiences on the Ironman team creating a pediatric prosthetic for a young local athlete. The goal of the Ironman team is to create a …

Transcribing Braille Code: Learning Equations Across Platforms, Deegan Atha, Courtney Balogh

Purdue Journal of Service-Learning and International Engagement

Deegan Atha, a graduating senior in electrical engineering and a future engineer, is interested in human-centered design and developing technology that helps students engage and be successful in STEM.

Courtney Balogh, a junior in mechanical engineering, is interested in human-centered design and the importance it plays in product development. Deegan and Courtney are members of the Purdue EPICS project, Learning Equations Across Platforms (LEAP). They partnered with the Indiana School for the Blind and Visually Impaired (ISBVI) to develop a braille transcription device and web application that converts braille to print in real time.

Large Eddy Simulations Of Vertical Jets In Crossflow, Pranaya Pokharel

LSU Doctoral Dissertations

Jets in crossflow (JICF) have applications ranging from oil spill to film cooling of turbine blades. Hence, an understanding of the flow physics is important. The majority of the research has been conducted for low velocity ratios between jet and crossflow with round jets. JICF is demonstrated to behave differently for high velocity ratios and different jet shapes. Circular and rectangular jets are commonly used in aircraft applications. Current study focuses on high velocity ratio JICF issuing from both circular and rectangular exit.

For simulating JICF, an in house code “Chem3D” is used with Large Eddy Simulation (LES) to model …

Numerical Study Of Liquid Atomization And Breakup Using The Volume Of Fluid Method In Ansys Fluent, Sai Saran Kandati

LSU Master's Theses

The spherical metal particles produced from the centrifugal atomization process have been the topic of numerous theoretical, experimental and numerical studies from the past few years. This atomization process uses centrifugal force to break-up molten material into spherical droplets, which are quenched into solidified granules by the flow of cold air on the spherical droplets. In the present work, a transient three-dimensional multiphase CFD model is applied to three different materials: Molten slag, aqueous glycerol solution, and molten Ni-Nb to study the influence of the dimensionless parameters on the centrifugal atomization outcome.

Results from numerical experiments indicated that the droplet …

Interface Model Of Pem Fuel Cell Membrane Steady-Dtate Behavior, Russell L. Edwards, Ayodeji Demuren

Mechanical & Aerospace Engineering Faculty Publications

Modeling works which simulate the proton-exchange membrane fuel cell with the computational fluid dynamics approach involve the simultaneous solution of multiple, interconnected physics equations for fluid flows, heat transport, electrochemical reactions, and both protonic and electronic conduction. Modeling efforts vary by how they treat the physics within and adjacent to the membrane-electrode assembly (MEA). Certain approaches treat the MEA not as part of the computational domain, but rather an interface connecting the anode and cathode computational domains. These approaches may lack the ability to consistently model catalyst layer losses and MEA ohmic resistance. This work presents an upgraded interface formulation …

Modular Crates – A Holistic Design Approach For Optimizing Cube Size In Industrial Packaging, Marshal Louie, Kumar B

Journal of Applied Packaging Research

Global market is a field where all industries strive to provide personalized product for every customer demand in order to compete with their competitors in the business battlefield. Product personalization varies with customer to customer which increases the product variety. When the product size variability is vast, producing packages for every individual product is not only difficult but also increases the design time, production time, total manufacturing cost and inventory cost. For the present scenario, Industrial packages does not opt customizability for variable product sizes. Customized package for personalized product is achievable only by redesigning the existing distribution package with …

Finding Balance In Generative Product Design, Alex Lobos

Presentations and other scholarship

Generative design develops complex forms and structures similar to those found in nature, taking advantage of automated tasks and high-scale computing power. This approach benefits designers in the creation systems that are efficient, resilient and visually engaging. These systems follow specific rules for form generation and meet clear design goals in terms of shape, strength, mass, and other physical attributes.

There is a large number of methods for creating generative systems, based on establishing desired outcomes and behaviors for how components relate to each other. Examples of methods include L-Systems, Shape Grammars, Swarm Intelligence, Form Optimization, Lattice Design, and many …

Purdue Air Sense: A Methodology For Improving The Accuracy Of Ambient Aerosol Mass Concentration And Size Distribution Measurement With Low-Cost Optical Sensing Techniques, Rishabh Ramsisaria, Satya Sundar Patra, Brandon Emil Boor

The Summer Undergraduate Research Fellowship (SURF) Symposium

There is a global lack of a means for monitoring air pollutant levels at a local level due to expensive and bulky instrument requirements. It is important to monitor toxic gas levels, as well as particulate matter levels, in the atmosphere to study their effects on human health and to further develop city- and community-level air pollution solutions. In this study, with the means of a Raspberry Pi, low-cost Alphasense Optical Particle Counter and gas sensors, and methodical calibration techniques, we built a portable 3-D printed module powered by clean electricity generated by an on-board Voltaic solar cell that measures …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …

Microstructure And Mechanical Properties Of Selective Laser Melted Superalloy Inconel 625., Md Ashabul Anam

Electronic Theses and Dissertations

Selective Laser Melting (SLM), a powder based Additive Manufacturing (AM) process, has gained considerable attention in the aerospace, biomedical and automotive industries due to its many potential benefits, such as, capability of fabricating complex three-dimensional components, shortened design to product time, reduction in process steps, component mass reduction and material flexibility. This process uses metallic powder and is capable of fabricating complex structures with excellent microstructure which make SLM not only an improvement over other manufacturing processes but also innovative material processing technology. Inconel 625, a nickel-based super alloy is widely popular in aerospace, chemical and nuclear industries. This alloy …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Modeling Of The Veterinary Anesthetic Circuit, Corinne Viloria Duplantis

LSU Master's Theses

Anesthesia is used to sedate both humans and animals for surgery. In veterinary practice, breathing systems are often used to supply anesthetic gas to the patient. Occasionally, a large amount of pressure can build up in the breathing circuit. This high pressure, if unnoticed, can lead to fatal injury to the lungs of the veterinary patient. The maximum allowable pressure in the anesthetic circuit for small animals is 25 cmH₂O or 2450 Pa. As such, it is necessary to monitor oxygen flow rate (ranging from 0.1-4 LPM), pressure, oxygen rate, anesthetic composition, among other variables during an operation. …

My Catalyst, Gabrielle Gambino Lyon

Celebration of Learning

Over the course of my internship and shadow program with Pepper Lawson Construction and Ziegler Cooper Architects, I was able to explore the various career paths involved in the design, construction, and civil engineering fields. My work on the construction site of a high-rise apartment building located in the heart of Houston, TX allowed me first-hand experience working and learning alongside project engineers, contractors, building developers, and the construction team.

This project was the perfect confluence of my main areas of interest: structural, mechanical, civil, and environmental engineering, as well as architecture. My daily work consisted of on-site walk throughs, …