Mechanical Engineering Commons^™

Application Of Remote Sensing And Geographic Information System Methods For Land Using Difference, Bangun Muljo Sukojo, Diah Susilowati

Makara Journal of Technology

Application of Remote Sensing and Geographic Information System Methods for Land Using Difference. Land using difference analysis has been done using remote sensing and Geographic Information System (GIS) methods. Identification of land using difference was conducted using map overlaying process of 1990s (digitized scalling 1:50.000) and 1997s land using map (interpreted from Landsat TM (Thematic Mapper) Image 1997) with UTM (Universal Transverse Mercator) coordinate. Image enhancement was done through histogram equalization with supervised classification devided into 7 classes: rice field, settlement, dry field, industry, pond, sport field and bush. Land using difference and river pollution BOD (Biological Oxygen Demand), COD …

Phase Composition Analysis Using Rietveld Methode And It's Influence To The Hardness Of Ti-Si-N Nanocomposites, Keba Moto, Lia Setiarini, Zufar Abubakar

Makara Journal of Technology

Phase composition analysis using rietveld methode and it’s influence to the hardness of Ti-Si-N nanocomposites. XRD data of nanocomposites Ti-Si-N have been analysed using GSAS based on Rietveld Method in order to identify phases and their composition as well as its influence on the hardness of these nanocomposites. Several new phases have been found in the sample beside the nc-TiN/a-Si3N4& a-/nc-TiSi2 that have been known widely. From the obtained crystalline phase, after the calculation of amorf Si3N4 and TiSi2 phase fraction, it is found that the optimum hardness can be reached when the fraction of a-Si3N4 phase around 8 wt.%

Influence Of Strain Rate And Temperature Of Hot Tension Testing On Mechanical Properties Of Medium Carbon Steel S48c, Dedi Priadi, Iwan Setyadi, Eddy S. Siradj

Makara Journal of Technology

Influence of Strain Rate and Temperature of Hot Tension Testing on Mechanical Properties of Medium Carbon Steel S48C. The characterization of S48C by hot tension testing was done to understanding the influence of temperature and strain rate for S48C flow stress, that close relationship with its forge ability. The hot tension testing was performed on temperatures and strain rates variation (T 850, 900, 950 0C and έ 0,01;1 s-1). The result of hot tension testing showed that increasing temperature decreases ultimate tensile strength (UTS) and flow stress of S48C. The higher decreasing of UTS is on 950 0C about 85% …

Experimental Energy Performance Of Open Cooling Towers Used Under Low And Variable Approach Conditions For Indirect Evaporative Cooling Of Buildings, Ben Costelloe, Donal Finn

Articles

The success of chilled ceilings and displacement ventilation systems as a means of sensible cooling in buildings has prompted a review of evaporative cooling technology as an effective means of generating the required cooling water. When such cooling water is generated at low approach conditions (2–5 K), at the higher temperatures required in these systems (14–18°C), very high levels of availability result. In many north western European locations the levels of availability are such that the prospect of supplanting rather than simply supplementing the refrigeration system, for sensible cooling purposes, arises. The viability of the technique, however, largely depends on …

Indirect Evaporative Cooling Potential In Air-Water Systems In Temperate Climates, Ben Costelloe, Donal Finn

Articles

Recent developments have prompted a review of evaporative cooling technology as an effective means of cooling modern deep plan buildings. Prominent among these developments is the success of high temperature sensible cooling systems, particularly, chilled ceilings, which require a supply of cooling water at 14–18 °C. Crucial to the success of evaporative cooling technology, as a significant means of cooling in modern applications, is the ability to generate cooling water, in an indirect circuit, at a temperature which closely approaches the ambient adiabatic saturation temperature (AST) or wet bulb temperature (WBT). Recent experimental research has demonstrated that it is technically …

Iodat Analysis Content In Cooking Ingredients Using Iodometry And X-Ray Fluorescence Methods., Nelson Saksono

Makara Journal of Technology

Iodat Analysis Content in Cooking Ingredients Using Iodometry and X-ray Fluorescence Methods. Salt iodization program using iodine fortification into salt method is the best method that is effective and economical to overcome the problems caused by iodine deficiency. However in, its development there are some issues clamed that the use of iodized salt is ineffective since iodine content reduces, even disappear when the salt mix with other cooking ingredients. In order to investigated the existence of iodine in cooking ingredients, a research applying iodometry and X-ray fluorescence methods was carry out. The result obtained by iodometry method showed decreases in …

Emission Gas Reducer On Motor Vehicle, Automobile, Light Engine Of Boat And Stationary Combustion Engine., I Gusti Bagus Wijaya Kusuma

Makara Journal of Technology

Emission gas reducer on motor vehicle, automobile, light engine of boat and stationary combustion engine. The use of motor vehicle should be followed by protection against damages on the environment, since the exhaust gas from combustion engine has significantly affect on air and environmental pollution. One method to solve the problems in air pollution has been done by using a re-heater designed in Mechanical Engineering Department, University of Udayana. In accordance to the test on the re-heater, it can be seen very clear that the re-heater has significantly reduce the CO emission of about 54%. It also reduces the CO2 …

Application Of Remote Sensing For Mapping Soil Organic Matter Content, Bangun Muljo Sukojo, Wahono Wahono

Makara Journal of Technology

Application of Remote Sensing for Mapping Soil Organic Matter Content. Information organic content is important in monitoring and managing the environment as well as doing agricultural production activities. This research tried to map soil organic content in Malang using remote sensing technology. The research uses 6 bands of data captured by Landsat TM (Thematic Mapper) satellite (band 1, 2, 3, 4, 5, 7). The research focuses on pixels having Normalized Difference Soil Index (NDSI) more than 0.3. Ground-truth data were collected by analysing organic content of soil samples using Black-Walkey method. The result of analysis shows that digital number of …

Optimation Model Of Planning Investment Dockyard With Approach Multi Objective Goal Programming, Ali Azhar

Makara Journal of Technology

Optimation model of planning investment dockyard with approach multi objective goal programming. The purpose of this research is to determine decision variable, goal function, alternative priority and achievement function in investment planning. From this optimation component, the model of ship yard investment planning could be achieved. The model of developed model in this research was the optimation of ship yard investment planning using multi objective goal programming approach. The model consist of 5 decision variable, 11 goal function, 2 alternative priority and 11 achievement functions. The model implementation was done toward PT ASSI investment planning. The calculation using from Quantitative …

Self-Ignition Properties Of Peat, Palm Shell Fibre And Woods, Yulianto Sulistyo Nugroho

Makara Journal of Technology

Self-ignition properties of peat, palm shell fibre and woods. Forest fire is one of the greatest environmental problems faced by Indonesia. Forest fires have destroyed million hectares of forest and land which cause economic loss, social problems including smoke related diseases and environmental disaster with long time consequences. The exothermic reactions of forest fuels that lead to fire can be initiated by a piloted flame and low-temperature oxidation mechanism. This paper presents the results of low temperature oxidation studies using forests fuel samples i.e. palm shell fibre, peat, woods and low-rank coal. The measured values of the critical oven temperatures …

The Use Of 2d Plastic Grating For Surface Profile And Dimension Manufacture Product Measurements By Using Ndt Moiré Technique, Retno Wigajatri P., Dini Andiani

Makara Journal of Technology

The Use of 2D Plastic Grating for Surface Profile and Dimension Manufacture Product Measurements by Using NDT Moiré Technique. Research of measuring the shape and dimension of object using the moiré technique have been done. Measurement have been made by observing the moiré space as a result of interaction between grating and its shadow casted on the object’s surface caused by the projector lamp with CCD camera. The acquired data was further processed by way of off-line. By successive phase shifts that is π/2, π dan 3π/2 towards the table tennis ball at the distance of 48 cm from the …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: I. Swamp Water, Sulistyoweni Widanarko, Henki W. Ashadi, Andri Krisnadi Wicaksono

Makara Journal of Technology

Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO4 2-, Cl-, NO3 -. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: Ii. Swamp Sludges, Henki W. Ashadi, Sulistyoweni Widanarko, Irma Gusniani

Makara Journal of Technology

A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO4 2-, Cl- and NO3 -. The research treatment used by emerging ST 37 and ST 60 within 60 days in ‘polluted’ sludge swamp area. Three variation of ‘polluted’ swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion …

The Effect Of Ca Content On Cao-Zeolite On Nitrogen Adsorption Capacity, Mohammad Nasikin, Tania Surya Utami, Agustina Tp Siahaan

Makara Journal of Technology

In industry, Ca zeolite is used as nitrogen selective adsorbent with the use of PSA (Pressure Swing Adsorption)/VSA (Vacuum Swing Adsorption) methods. Natural zeolite modified to be Cao-zeolite by ion exchange process using Ca(OH)2. Adsorption test was done on CaO-zeolite with different Ca concentration to understand how it’s adsorption phenomena on oxygen and nitrogen. Adsorption test has been done for CaO-zeolite with Ca concentration = 0,682%, 0,849% and 1,244% to oxygen and nitrogen with equal concentration seperately. Pressure variation has being done three times (5 minutes long each time) adsorption time to analyze the connection between adsorption time and how …

Cetane Number Booster Additive For Diesel Fuel Synthesized From Coconut Oil, Mohammad Nasikin, Rita Arbianti, Abdul Azis

Makara Journal of Technology

To reduce NOx, SOx, HC, and particulates that produce because of using diesel fuel, can be done by increasing cetane number. One of methods is adding an additive to diesel fuel. 2-Ethyl Hexyl Nitrate (2-EHN) is a commercial additive that an organic nitrate. Making an additive in this research is used palm oil by nitration reaction that used HNO3 and H2SO4. Result of this reaction is methyl ester nitrate that has a structure looks like 2-EHN. IR spectra from research show that methyl ester nitrate is indicated by spectrum NO2 at 1635 cm-1. This result show that methyl ester nitrate …

Analogy Method Development For Cost Estimation Of Software Design, Riyanarto Sarno, Joko Lianto Buliali, Siti Maimunah

Makara Journal of Technology

The important aspect of planning and managing software development project is to estimate the cost of a project. There are several methods for estimating the cost of a software development project, and the Analogy method is a method which gives relatively better estimates. This paper shows that the modified Analogy method selects a closer project reference, estimates more accurate project effort and cost. This study enhances the cost estimate technique by including valid and complete cost parameters, therefore the estimate of a project cost is better than the result of the standard Analogy method.

The Role Of Si3n4 Amorphous Phase In Nc-Tin/A-Si3n4 Nanocomposites In Increases The Hardness And Thermal Stability, Keba Moto

Makara Journal of Technology

The role of Si3N4 amorphous phase in nc-TiN/a-Si3N4 nanocomposites will be shown and compared with polycrystalline ZrN/Ni which has no such amorphous phase (non-composites). The presence of amorphous phase Si3N4 increases the hardness of film as well as the toughness of the bulk nanocomposites under indentation load. It has been observed that nc-TiN/a-Si3N4 nanocomposites films has higher thermal stability than ZrN/Ni polycrystalline films.

Biodiesel's Characteristics Preparation From Palm Oil, Tilani Hamid. S, Rachman Yusuf

Makara Journal of Technology

Biodiesel’s characteristics preparation from palm oil. Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester) by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH) as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio …

Development Of Hardness Measurement Procedure For Nanocomposite Nc-Tin/A-Si3n4, Keba Moto

Makara Journal of Technology

Hardness of nc-TiN/a-Si3N4 nanocomposites which was determined by using two methods of measurements i. e. depth sensing method and remaining plastic indentation area that were magnified by using SEM (Scanning Electron Microscope) lie in the good agreement. The hardness value is not influenced by the biaxial and residual compressive stress. The measurement of the biaxial stress on the substrate shows a very small value of biaxial stress as well as the constant hardness and crystallite size against annealing temperature. Therefore, the reported hardness value here is the intrinsic value that depend on its microstructure properties.

Modeling And Simulation Of The Chemical Etching Process In Niobium Cavities, Qin Xue

UNLV Theses, Dissertations, Professional Papers, and Capstones

Niobium Cavities are important parts of the integrated NC/SC high-power linear accelerator (linac) that can accelerate over 100 mA of protons to several GeV. Surface finish of the niobium cavity plays an important role of achieving the best performance of niobium cavity. The chemical etching techniques have been widely used.

Chemical etching of the inner surface of the cavity is achieved by circulating acid through it. The acid interacts with the surface and eliminates imperfections. During the etching process, a pipe with baffles is inserted within the cavity to direct the flow along the surfaces.

A 2-D, axisymmetric, steady state, …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …

Development Of A Model For Induction Heating, Randy Clarksean, Yitung Chen

Fuels Campaign (TRP)

There are two coupled equations that must be solved in order to determine the power deposition. The numerical solution of these equations is needed in order to apply a source term within the energy equations. These equations have previously solved in FIDAP. That implementation used modified versions of the momentum and energy equations to provide a mechanism for the solution of two coupled equations. Currently, we want to solve for the induction heating field in addition to the flow field and the energy equation. In order to do this, a mechanism has to be defined within FIDAP to solve these …

Integrating Passenger And Modulo As Learning Tools For Collaborative Engineering Education, Kalamullah Ramli, Frank Schwarz, Stefan Werner, A Halim Shamsuddin, Axel Hunger

Makara Journal of Technology

The University of Indonesia (UI), Gerhard Mercator University (GMU), the Universiti Kebangsaan Malaysia (UKM) have agreed to cooperate as partners to develop a joint bachelor (3+1) and masters (1+1) degree, and collaborate in the research fi elds of multimedia- and internet-based learning and application level active networks. This paper describes the introduction of the Offshore Project and the extending of information technology applications to the partner institutions in this international cooperation which would very much enhance the operations of the new initiative in engineering education, which could provide students in far distance with more fl exible learning environment.

Study Effect Of Salt Washing Process On Content And Iodium Stability Of Salt, Nelson Saksono

Makara Journal of Technology

Effect of Salt Washing Process on Content and Iodium Stability of Salt. Salt washing process should increase the salt quality. It should clean the salt from sludge or clay and also reduce the impurity compound such as Mg, Ca and the reductor content. The objective of these reseach is to assess the effect of washing process on the content og hygroscopic impurities compound (Ca and Mg), and reductor content of salt. The research also investigate the water absorbing, pH, KIO3 content as function of time to obtain effect of washing process on KIO3 stability in salt. The experiment result shows …

Object Classfification In Computer Vision With Discriminant Analysis, Amir Hamzahan

Makara Journal of Technology

A robotic sensor system is always supported by a computer system called ‘computer vision’. The important concept of computer vision is object classfifi cation. In this study two algorithms for object classifi cation in this system will be compared. Firstly, A simple method that do not need complex computation and that considered as an informal method is called binary tree decision structure. This method is based on modest caracteristic decriptors of an object such as vertical line, horizontal line or ellipse line. Unfortunately this method has weakness in recognize an image that contaminated by a noise. Secondly, a more formal …

Making Alloys (Ti1 - Xalx) N Using Plasma Cvd Technique From Alcl3 Powder, H2 And N2 Gas ,With Solvent Ticl4, Keba Moto

Makara Journal of Technology

The substitution of Ti atoms by Al atoms in TiN lattice sites to form (Ti1-xAlx)N is clearly demonstrated by the coatings which were deposited on steel substrate and using plasma CVD technique. The presence of Al atoms in TiN lattice site is shown by means of XRD and EDX techniques: lattice parameters decreasing of TiN as the fraction of Al increases (XRD) and precipitation of hexagonal AlN phase (XRD) as the fraction of Al exceeding 0.8 (EDX). The hardness of these coating are just around 30 GPa, which is beyond the values reported in literatures.

Effects Of 0.25 % Mo (Molybdenum) Which Is Contained In The Ductile Cast Iron On Mechanical Properties Of Austempered Ductile Iron (Adi)., Nukman Nukman, Bustanul Arifin, Bambang Sugiarto

Makara Journal of Technology

The aim of this research is to investigate the effects of 0.25 % Mo (Molybdenum) which is contained in the ductile cast iron on mechanical properties of Austempered Ductile Iron (ADI). The various temperatures and the holding times are used in the heat treatment processes. Using a given 0.25 % Mo in the ductile iron, ADI's alloyed developes a higher ultimate tensile stress value and decreases the elongation if we compare with the as cast (non alloy ductile iron). The higher impact energy value obtained at 9000 C austenization and 375o C austempering temperatures during 60 minutes holding times. The …

The Manufacturing Properties Of Galvanised Steel Sheet With Hexagonal And Tetragonal Network Of Circle Holes, Rahmat Saptono

Makara Journal of Technology

Galvanized steel sheet of 0.8 mm in thickness was drilled with circle holes of 2.5 mm diameter and spacing arranged in tetragonal and hexagonal pattern. The manufacturing properties of specimen were studied through drawing and stretching simulative test. It was concluded from the results that, at high ratio of punch to hole diameter (40/2.5), the drawing properties (LDR) of both square and hexagonal perforated sheet were slightly lower than that of solid sheet, while hexagonal perforated showing LDR somewhat higher than the square one. The stretching properties (LDH) of sheet, however, were much lower than that of solid sheet while …

Develops The Software Of Dsp Processor For The Cdma Circuitry, Arman Djohan D.

Makara Journal of Technology

This research develops the software of DSP Processor type TMS320C54X for the CDMA circuitry. This research apply two algorithms namely Mathematic Algorithm and table lookup Algorithm. From both algorithms, the research examine what algorithm have the fasted processing time and the smallest memory occupation. From the examination results the Mathematic Algorithm have 20.62 milliseconds processing time and the Table lookup algorithm have 14.08 milliseconds processing time. The Table lookup algorithm have the fastest processing time because the Matematic algorithm need the rounding process of the fi gure. Eventhough such processing time is not exceed from the 125 millisecond of delay …

Thermodynamics And Bioenergetics, Yaşar Demirel, Stanley I. Sandler

Papers in Thermal Mechanics

Bioenergetics is concerned with the energy conservation and conversion processes in a living cell, particularly in the inner membrane of the mitochondrion. This review summarizes the role of thermodynamics in understanding the coupling between the chemical reactions and the transport of substances in bioenergetics. Thermodynamics has the advantages of identifying possible pathways, providing a measure of the efficiency of energy conversion, and of the coupling between various processes without requiring a detailed knowledge of the underlying mechanisms. In the last five decades, various new approaches in thermodynamics, non-equilibrium thermodynamics and network thermodynamics have been developed to understand the transport and …