Mechanical Engineering Commons^™

Thermodynamics And Bioenergetics, Yaşar Demirel, Stanley I. Sandler

Papers in Thermal Mechanics

Bioenergetics is concerned with the energy conservation and conversion processes in a living cell, particularly in the inner membrane of the mitochondrion. This review summarizes the role of thermodynamics in understanding the coupling between the chemical reactions and the transport of substances in bioenergetics. Thermodynamics has the advantages of identifying possible pathways, providing a measure of the efficiency of energy conversion, and of the coupling between various processes without requiring a detailed knowledge of the underlying mechanisms. In the last five decades, various new approaches in thermodynamics, non-equilibrium thermodynamics and network thermodynamics have been developed to understand the transport and …

Effects Of Concentration And Temperature On The Coupled Heat And Mass Transport In Liquid Mixtures, Yaşar Demirel, Stanley I. Sandler

Papers in Thermal Mechanics

Using published experimental data on the thermal conductivity, mutual diffusivity, and heats of transport, the degree of coupling between heat and mass flows has been calculated for binary and ternary nonideal liquid mixtures. The binary mixtures consist of two types: the first is six systems of six-to-eight-carbon straight and branched chain alkanes in chloroform and in carbon tetrachloride; and the second is mixtures of carbon tetrachloride with benzene, toluene, 2-propanone, n-hexane, and 11-octane. The ternary mixture considered is toluene-chlorobenzene-bromobenzene. The published data are available at 35°C, 30°C, and 35°C and ambient pressure. Using the linear nonequilibi-ium thermodynainics (LNET) and the …

Mathematical Modeling For Fabricating A Microstructure With A Pre-Specified Geometry Using Laser -Induced Chemical Vapor Deposition, Chaoyang Zhang

Doctoral Dissertations

Laser-induced chemical vapor deposition (LCVD) is an emerging new technique with many practical applications. To optimize the system for fabricating a microstructure with a pre-specified geometry in pyrolytic LCVD, a three-dimensional mathematical model is developed for predicting temperature distributions and laser dwell times across the substrate scanned by the laser beam. A microstructure is fabricated layer by layer, and for each layer the laser beam moves from one pixel to the next. The complicated correlations among temperature distribution, deposit growth rate, and laser dwell time are investigated. A purely heterogeneous reaction is assumed and any gas-phase transport is ignored.

A …

Linear-Nonequilibrium Thermodynamics Theory For Coupled Heat And Mass Transport, Yaşar Demirel, Stanley I. Sandler

Yaşar Demirel Publications

Linear-nonequilibrium thermodynamics (LNET) has been used to express the entropy generation and dissipation functions representing the true forces and flows for heat and mass transport in a multicomponent fluid. These forces and flows are introduced into the phenomenological equations to formulate the coupling phenomenon between heat and mass flows. The degree of the coupling is also discussed. In the literature such coupling has been formulated incompletely and sometimes in a confusing manner. The reason for this is the lack of a proper combination of LNET theory with the phenomenological theory. The LNET theory involves identifying the conjugated flows and forces …

The Effect Of System And Oxygen Partial Pressure On Single Coal Particle Heterogeneous Ignition Temperature Under Conditions Of Negligible Convection; Experimental Observation, H. Katalambula

Tanzania Journal of Engineering and Technology (TJET)

Abstract Under conditions of high volatile concentrations, the influence of oxygen concentration on single coal particle ignition becomes more significant. The high volatile concentration conditions have been simulated by employing a microgravity environment. Results show that under these conditions, the heterogeneous ignition temperature decreases faster with increasing oxygen concentration than under normal conditions. The ignition temperature also decreases with increasing system and oxygen partial pressure under both conditions. Generally, the system and oxygen partial pressure show similar and complimenting effects on ignition temperature.

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Estimation Of Volatile Cloud Density For Single Coal Particles Using Microgravity Condition, H. Katalambula

Tanzania Journal of Engineering and Technology (TJET)

Single coal particle’s volatile cloud density has been estimated by employing a microgravity condition. The volatile yield was found to decrease with pressure while the density was found to increase, indicating that volatiles occupies less space when under pressure and hence causing some volatiles to be retained within the particle. The volatile cloud density was also found to increase with volatile yield suggesting volatile composition changes with yield. The effect of heating rate on volatile yield was found to be the same as reported by other investigators where the yield increased with heating rate.

Measurement Of Markstein Lengths In Laminar Spherical Explosion Flames, E .M.J Mushi

Tanzania Journal of Engineering and Technology (TJET)

Schlieren photography was used to record the development of spherical flames in a combustion bomb. Flame speed and flame stretch were evaluated from the data and used to evaluate Markstein lengths and numbers. The results indicate a strong influence of both the spark discharge energy and equivalence ratio. Low spark discharge energy is observed to give rise to more unstable flames compared to high energy sparks. It is observed that for the range of energy tested, 80 and 400 mJ gave the best stability for the flames. For equivalence ratio less or equal to 1.225 an 80 mJ discharge results …

Computation Of Flame Base Height Of A Turbulent Diffusion Flame Resulting From A Methane Jet, A. S. Kheireddine, S. K. Chaturvedi, T. O. Mohieldin

Mechanical & Aerospace Engineering Faculty Publications

This work summarizes numerical results for a diffusion flame formed from a cylindrical tube fuel injector, issuing a gaseous methane jet vertically in a quiescent atmosphere. The primary objective is to predict the flame base height and other flame characteristics as a function of the fuel jet velocity. A finite volume scheme is used to discretize the time-averaged Navier-Stokes equations for the reacting flow resulting from the turbulent fuel jet motion. The turbulent stresses, and heat and mass fluxes are computed from a Reynolds stress turbulence model. A chemical kinetics model involving two-step chemistry is employed for the oxidation of …

Entropy Generation In A Rectangular Packed Duct With Wall Heat Flux, Yaşar Demirel, Ramazan Kahraman

Papers in Thermal Mechanics

The entropy generation due to heat transfer and friction has been calculated for fully developed, forced convection flow in a large rectangular duct, packed with spherical particles, with constant heat fluxes applied to both the top (heated) and bottom (cooled) wall. An approximate analytical expression for the velocity profile developed for packed bed with H/dp > 5 has been used together with the energy equation of fully developed flow to calculate the non isothermal temperature profiles along the flow passage. The velocity profile takes into account the increase in the velocity near the wall due to the higher voidage in this …

Fuel Cells, Frederick J. Munster Jr.

Maine Collection

Fuel Cells

by Frederick J. Munster Jr.

Edited by: Mr. Christopher Carroll

Maine Department of Economic Development, Augusta, Maine, 1998.

Contents: Hydrogen / Hydrogen Safety / Electrolysis / Electrolyzers / History of Fuel Cells / How Fuel Cells Operate / Fuel Cell Types / Fuel Cell Electrochemistry / Power Systems / Fuel Cells in Transportation / Hydrogen Powered Internal Combustion Engines / Home, Garden, Education and Industry / For More Information / Glossary / References

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

Characterization Of The Si/Sio2 Interface Formed By Remote Plasma Enhanced Chemical Vapor Deposition From Sih4/N2O With Or Without Chlorine Addition, Young-Bae Park, Xiaodong Li, Shi-Woo Rhee

Faculty Publications

The Si/SiO₂interface formed by remote plasma enhanced chemical vapor deposition (RPECVD) at low temperature with SiH₄/N₂O or SiH₄/N₂O/Cl₂ was studied and compared with thermal oxidation. The interface of the CVD SiO₂ without chlorine addition is rougher than that with chlorine addition. But the surface roughness of CVD SiO₂ films increases with chlorine addition. The thermal oxidation induces strong interface strains, and the strains generated by the CVD SiO₂ without chlorine addition are stronger and are distributed more nonuniformly than those by the chlorinated SiO₂. …

Droplet Evaporation And Deformations In An Amplitude Modulated Ultrasonic Field, Nihad E. Daidzic, Rene Stadler, Adrian Melling

Aviation Department Publications

The aim of the report presented is the measurements of droplet oscillations.

Heat Transfer In Rarefied Gas At A Gas-Solid Interface, Yaşar Demirel, Satish C. Saxena

Papers in Physical Chemistry

Modified expressions for the heat-transfer fluxes at the interface of a solid surface and a gas are given for different Knudsen-number regimes. These expressions for diatomic gases contain both a gas-reflection and a thermal accommodation coefficient. Parallel-plate, coaxial-cylindrical and concentric spherical surfaces are considered. A general expression for the thermal accommodation coefficient is based on experimental data. Sample numerical calculations of heat flux in different heat-transfer regimes are presented in terms of the reciprocal Knudsen number.

Structural Characterization Of Aluminum Films Deposited On Sputtered-Titanium Nitride/ Silicon Substrate By Metalorganic Chemical Vapor Deposition From Dimethylethylamine Alane, Xiaodong Li, Byoung-Youp Kim, Shi-Woo Rhee

Faculty Publications

Alfilmsdeposited on sputtered‐TiN/Si substrate by metalorganic chemical vapor deposition(MOCVD) from dimethylethylamine alane (DMEAA) were characterized using x‐ray diffraction(XRD),Auger electron spectroscopy(AES),atomic force microscopy(AFM), and transmission electron microscopy (TEM). The TiN filmsputtered on the Si has a preferred orientation along the growth direction with the 〈111〉 of the film parallel to the Si〈111〉. Sputtering of the TiN film on the Si induced strains at the interface. The TiN/Si interface is flat while the Al/TiN interface is rough. There exist many dislocations at the Al/TiN interface. The Al₂O₃ phase was formed at the Al/TiN interface during the early stages of …

Studies Of Mixing Processes In Gases And Effects On Combustion And Stability, Frank Paul Kozusko Jr.

Mathematics & Statistics Theses & Dissertations

Three physical models of laminar mixing of initially separated gases are studied. Two models study the effects of the mixing dynamics on the chemical reactions between the gases. The third model studies the structure and stability of a laminar mixing layer in a binary gas. The three models are:

1. Two ideal and incompressible gases representing fuel and oxidizer are initially at rest and separated across an infinite linear interface in a two dimensional system. Combustion, expected as the gases mix, will lead to a rapid rise in temperature in a localized area, i.e. ignition. The mixing of the gases …

A New Spray Evaporation Model Based On Droplet Interface Phenomena, Nihad E. Daidzic, Gangolf Kohnen, Martin Sommerfeld

Aviation Department Publications

In this work the influence of droplet shape oscillations on droplet evaporation is shown. Through nonlinear mode interactions, turbulence and aerodynamic triggering of vibrations cause by vortex shedding, droplets always oscillates in spray flows. Droplet shape oscillation cause higher evaporation rates through several physical phenomena such as an average increase of the superficial surface area, periodic micro-convection and boundary layer destruction, and local saturation pressure changes due to local curvature effects. The inviscid theory of small-amplitude droplet oscillations was used which resulted in better agreement with the measurement data of droplet size distributions in sprays for different axial coordinates.

Excess Heat Capacity Surfaces For Water-Alkanol Mixtures By The Uniquac Model, Yaşar Demirel, Halime Ö. Paksoy

Papers in Physical Chemistry

Hydroorganic mixtures are industrial solvents that can serve as media to solubilize either water in hydrocarbon or a hydrophobic substance in water. In many cases the solubilizing capability is obtained via a homogeneous complex aqueous mixtures containing an alcohol. Since excess heat capacity C_P^E, is very sensitive to structural changes in mixtures, concentration and temperature dependence of C_P^E have been calculated by using the UNIQUAC model for the mixtures methanol(l)-water(%, ethanol(l)-water(2), and l-propanol(l)-water(2). The temperature-dependent parameters of the model estimated directly from C_P^E data at more than one different isotherm are used in …

A Study Of The Thermodynamic And Heat Transfer Characteristics Of Two-Phase Two-Component Flow With Application To A Solar-Assisted Heat Pump, Walid A. Aziz

Mechanical & Aerospace Engineering Theses & Dissertations

Two-phase flow of single component refrigerants has been studied, theoretically and experimentally, for many CFCs, in many industrial applications, including the solar-assisted heat pump system. This study extends the thermodynamic and heat transfer analysis in the phase transition boiling region, to newly proposed refrigerant mixtures, which are candidates for replacing the classical CFCs for future HVAC applications. The goal of this study is to develop a methodology, to design the collector/evaporator tubes of a solar-assisted heat pump, using a binary refrigerant mixture as the working fluid. The method is implemented numerically as a computer algorithm. In order to do that, …

Studies On Nonequilibrium Phenomena In Supersonic Chemically Reacting Flows, Rajnish Chandrasekhar

Mechanical & Aerospace Engineering Theses & Dissertations

This study deals with a systematic investigation of nonequilibrium processes in supersonic combustion. The two-dimensional, elliptic Navier-Stokes equations are used to investigate supersonic flows with nonequilibrium chemistry and thermodynamics, coupled with radiation, for hydrogen-air systems. The explicit, unsplit MacCormack finite-difference scheme is used to advance the governing equations in time, until convergence is achieved.

For a basic understanding of the flow physics, premixed flows undergoing finite rate chemical reactions are investigated. Results obtained for specific conditions indicate that the radiative interactions vary substantially, depending on reactions involving HO$\sb2$ and NO species, and that this can have a noticeable influence on …

Effects Of Radiative Interactions In Molecular Gases Under Local And Nonlocal Thermodynamic Equilibrium Conditions, Manoj Kumar Jha

Mechanical & Aerospace Engineering Theses & Dissertations

Basic formulations, analyses, and numerical procedures are presented to investigate radiative heat interactions in diatomic and polyatomic gases under local and nonlocal thermodynamic equilibrium conditions. Essential governing equations are presented for both gray and nongray gases. Information is provided on absorption models, relaxation times, and transfer equations. Radiative flux equations are developed which are applicable under local and nonlocal thermodynamic equilibrium conditions.

The problem is solved for fully developed laminar incompressible flows between two parallel plates under the boundary condition of a uniform surface heat flux. For specific applications, three diatomic and three polyatomic gases are considered. The results are …

Transient Simulation Of A Trombe Wall Passive Heating System Coupled To A Thermally Stratified Room, Ali Saleh Kheireddine

Mechanical & Aerospace Engineering Theses & Dissertations

Thermal performance of a Trombe-wall space heating system has been studied numerically for one-day and multiple-day periods. This study analyzes the system performance by simultaneously considering the coupled nature of the channel convection, wall heat conduction and transient room energy balance. A computer program has been written and implemented to assess the effects of system parameters, weather conditions and peak temperature control strategies on the system performance.

The system performance is influenced by such system parameters as the storage wall thickness, channel width and the temperature stratification in the room. Increasing the wall thickness decreases the temperature swings considerably, but …

Analysis Of Heat Pump Cycles Using Thermodynamic Equations Of State, Stephen C. Ericson

Mechanical & Aerospace Engineering Theses & Dissertations

In this study, thermal performance of heat pump cycles is analyzed by employing several equations of state. The analysis presented here is particularly useful for applications where refrigerant properties need to be calculated from a thermodynamic equation of state. Such a situation, for example, would arise during a long-term numerical simulation of a solar-assisted heat pump system. In these cases, the direct use of thermodynamic property tables of refrigerants would not be possible in a computational procedure. The approach of using equations of state to predict thermodynamic properties is also useful for applications where new refrigerants or blends of refrigerants …

A Mathematical Model And Simulation Of Natural Circulation Loop Thermalhydraulics, Nihad E. Daidzic

Aviation Department Publications

In this work, a simple, nonlinear, seventh-order mathematical model with lumped parameter analysis of the thermalhydraulic processes in a natural circulation steam boiler loop is presented. Digital simulation has been performed in order to predict open loop transients in severe accidental situations. Parts of the circulation loop such as the steam drum, downcomer, and riser were modelled separately on the basis of the integral balance equations. The two-phase flow in the steam drum and in the riser was modelled with the aid of a homogeneous-equilibrium, two-phase flow model. Special care was taken to ensure the stability of the numerical scheme, …

Methods Of Measuring The Solubility And Viscosity Of Lubricating Oil/Refrigerant Mixtures At High Discharge Pressures And Temperatures, Nolan Van Gaalen

Faculty Work Comprehensive List

The design and construction of a test facility and methodology for measuring the solubility and viscosity of lubricating oil/refrigerant mixtures at high pressures and temperatures are described. An auxiliary charging system, developed to provide precisely measured quantities of oil and refrigerant to the test facility, is also presented. The test facility was developed under the sponsorship and supervision of ASHRAE which funded this research project (RP-580);The solubility, viscosity and density of mixtures of R-22 and of R-502 with commonly used 150 SUS lubricants have been measured by using this facility. Specifically, results for liquid mixtures of 10% to 40% refrigerant …

Effect Of Viscoplastic Flow Rules On The Initiation And Growth Of Shear Bands At High Strain Rates, R. C. Batra, Chang-Soo Kim

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Marchand and Duffy have reported detailed measurements of the temperature and strain as a shear band develops in a HY-100 steel. Assuming their torsional tests in thin-wall tubes can be adequately modeled by a viscoplastic block undergoing overall adiabatic simple shearing deformations, we investigate the effect of modeling the viscoplastic response of the material by a.power law, and flow rules proposed by Litonski, Bodner and Partom, and Johnson and Cook. Each of these flow rules is first calibrated by using the test data at a nominal strain-rate of 3300 s-1. Then predictions from the use of these flow rules at …

Application Of Mechanical Vapour Recompression To Industrial Slides Drying, Allan Issangya

Tanzania Journal of Engineering and Technology (TJET)

A positive result of the oil crisis of the seventies is the realisation of energy’s value and the need to use it sparingly. Increasing attention has been focussed on all aspects of industry where fuel oil and gas had played a major role.

Industrial drying, one of the most widely applied unit operations in chemical and process engineering, is a highly energy intensive operation. Studies have identified a number of alternatives for lowering energy consumption in this process through various heat recovery techniques.

Due to the difference in their operating principles steam-heated dryers and air-heated dryers, in most aspects, require …

Development Of A Parametric Analysis Microcomputer Model For Evaluating The Thermodynamic Performance Of A Reciprocating Brayton Cycle Engine, Thomas Joseph White

Dissertations and Theses

In this thesis, applicable data from research on IC engines have been adapted to PACE engine designs. Data from studies on heat transfer, friction, and pressure losses, in particular, have been used. Certain parameters which define operation and design characteristics appear to influence PACE engine performance very strongly. Some of the more critical parameters, notably friction and heat transfer coefficients, must be determined experimentally if accurate model results are to be expected. Pressure ratio, compressor RPM, and maximum combustor temperature, the independent operating parameters, also have a dramatic effect on engine performance. Other design or operating characteristics and working fluid …

Simplifying Lubricants For Farm Machinery, R A. Platt

Journal of the Department of Agriculture, Western Australia, Series 4

All moving parts on machinery needs lubrication. With the rapid development in farm machinery and its attendant sophistifications, the stresses imposed on the lubricants have also increased.

This article looks at some of the changes in requirements and developments in lubricants available.