Mechanical Engineering Commons^™

Design Of Medical Devices For Diagnostics In The Gastrointestinal System, Charles R. Welch

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents the design, controls, and testing of two systems: a novel colonoscope locomotion design for diagnostics, and a biosensor capsule that implants a sensor in the small intestine. Each system requires special design considerations for use in the gastrointestinal system.

Colonoscopy procedures are recommended as a screening for colon cancer and related conditions after the age of 50. The need for an improved colonoscope that reduces the colonoscopy time and patient discomfort is apparent. The semi-autonomous device presented here could likely reduce the colonoscopy procedure time by allowing the physician to focus more on the diagnosis and less …

Molecular Combing Of Dna Nanofibers And Comparison To Electrospinning, Tanner L. Buresh

UCARE: Research Products

The goal of these experiments was to create DNA nanofibers through the method of molecular combing (MC) and then compare the MC fibers to fibers created with electrospinning (ES). The experiment was designed and initial samples were created. After confirming that the method would succeed in creating DNA fibers, several parametric studies were performed in order to optimize the experiment and create the most uniform fibers possible. The parametric studies were done on the following variables: substrate material, pH level of DNA solution, and DNA solution concentration. After completion of all experiments, it was determined that although fibers could be …

Design And Analysis Of A Lift Assist Walker, Deep P. Shah

Master's Theses

Walkers provided stability to the elderly but cannot assist a person from sitting to standing. The objective of this project is to present the design and analysis of a lift assist walker. This report discusses the design and analysis of a collapsible lift assist walker capable of lifting a patient up to 250 lbs. from seated to standing in under 10 seconds. The designed walker utilized a two stage scissor mechanism with a gas spring assisted embedded linear actuator.

Multimodal, Biomaterial-Focused Anticoagulation Via Superlow Fouling Zwitterionic Functional Groups Coupled With Anti-Platelet Nitric Oxide Release, Kagya Amoako, Harihara S. Sundaram, Ahmed Suhaib, Shaoyi Jiang, Keith E. Cook

Mechanical and Industrial Engineering Faculty Publications

The functions of anti-fouling, zwitterionic polycarboxybetaine (pCB) and anti-platelet nitric oxide (NO) release replicate key anticoagulant properties of the endothelium. The two approaches, only tested separately thus far, were paired on gas permeable polydimethylsiloxane (PDMS) membranes and evaluated for anti-coagulation. Uncoated PDMS (control) and PDMS coated with pCB were screened for fibrinogen (Fg) fouling followed by platelet adsorption testing to evaluate the effects of coating and/or NO using bioreactors. Bare or coated PDMS membranes separated sheep plasma (108 platelets/ml) and gas flow chambers within the bioreactors. Either 100 or 0 ppm of NO/N2 flowed through the gas chamber for NO …

Multidisciplinary Game-Based Approach For Generating Student Enthusiasm For Addressing Critical Infrastructure Challenges, John F. Gardner

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Building upon experiences from past course offering,¹ several universities across the United States (U.S) have incorporated a critical infrastructure educational game platform as a unifying platform to integrate different disciplines to a common goal. The critical infrastructure backbones of the world provide the delivery mechanisms for energy and other utilities that provide the lifestyle we have come to expect in our society. As these critical infrastructure systems have evolved, the complexity of their integration has generated numerous challenges as a side effect of increased automation that are more pronounced as the infrastructure ages. Although still a modern technological wonder, …

Expanded 3d Nanofiber Scaffolds: Cell Penetration, Neovascularization, And Host Response, Jiang Jiang, Zhuoran Li, Hongjun Wang, Yue Wang, Mark A. Carlson, Matthew J. Teusink, Matthew R. Macewan, Linxia Gu, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Herein, a robust method to fabricate expanded nanofiber scaffolds with controlled size and thickness using a customized mold during the modified gas-foaming process is reported. The expansion of nanofiber membranes is also simulated using a computational fluid model. Expanded nanofiber scaffolds implanted subcutaneously in rats show cellular infiltration, whereas non-expanded scaffolds only have surface cellular attachment. Compared to unexpanded nanofiber scaffolds, more CD68+ and CD163+ cells are observed within expanded scaffolds at all tested time points post-implantation. More CCR7+ cells appear within expanded scaffolds at week 8 post-implantation. In addition, new blood vessels are present within the expanded scaffolds at …

Efficiency Evaluation Of A Magnetically Driven Multiple Disk Centrifugal Blood Pump, Kayla H. Moody

Theses and Dissertations

Heart failure is expected to ail over 8 million people in America by 2030 leaving many in need of cardiac replacement. To accommodate this large volume of people, ventricular assist devices (VADs) are necessary to provide mechanical circulatory support. Current VADs exhibit issues such as thrombosis and hemolysis caused by large local pressure drops and turbulent flow within the pump. Multiple disk centrifugal pumps (MDCPs) use shearing and centrifugal forces to produce laminar flow patterns and eliminate large pressure drops within the pump which greatly reduce risks that are in current VADs. The MDCP has a shaft drive system (SDS) …

Computational Assessment Of Neural Probe And Brain Tissue Interface Under Transient Motion, Michael Polanco, Sebastian Bawab, Hangsoon Yoon

Mechanical & Aerospace Engineering Faculty Publications

The functional longevity of a neural probe is dependent upon its ability to minimize injury risk during the insertion and recording period in vivo, which could be related to motion-related strain between the probe and surrounding tissue. A series of finite element analyses was conducted to study the extent of the strain induced within the brain in an area around a neural probe. This study focuses on the transient behavior of neural probe and brain tissue interface with a viscoelastic model. Different stages of the interface from initial insertion of neural probe to full bonding of the probe by astro-glial …

Biventricular Finite Element Modeling And Quantification Of 3d Langragian Strains And Torsion Using Dense Mri, Zhanqiu Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

Statistical data suggests that increased use of evidence-based medical therapies has largely contributed to the decrease in American death rate caused by heart disease. And my studies are about two applications of magnetic resonance imaging (MRI) as a non-invasive approach in evidence-based health care research. In my first study, the achievement of a pulmonary valve replacement surgery was assessed on a patient with tetralogy of Fallot (TOF). In order to evaluate the remodeling of right ventricle, two biventricular finite element models were built up for pre-surgical images and post-surgical images. In my second study, 3D Lagrangian strains and torsion in …

Diffusion-Mediated Deposition Of Proteins, Ruiqian Zhan

Theses and Dissertations--Mechanical and Aerospace Engineering

Gradients of proteins play a prominent role in many biological processes, from development of multicellular organisms to chemical signaling in the immune system. Deposition of surface gradients is a way to permanently modifying a surface’s properties, resulting in the creation of novel materials which have widespread applications in biologically relevant fields, such as directed cell growth, production of biocompatible implantable materials, and creation of functional biosensors. These types of surfaces can also be used as an ex vivo tool to help understand many biological processes by mimicking the environment in gradient-related phenomena in a controllable way. However, despite the large …

Knee Internal Forces In Moderate Squat Exercise, Dumitru I. Caruntu, Jose Mario Salinas

Mechanical Engineering Faculty Publications

This paper deals with internal forces of human knee during moderate squat exercise. The moderate squat exercise consists of a descending phase from standing to the lowest position (largest flexion angle) in which no significant contact between thigh and calf occurs, and an ascending phase back to standing position. This research predicts the internal forces such as muscle forces, contact forces, and ligamentous forces. The ligamentous structures in this research consist of Anterior Cruciate Ligament (ACL), Posterior Cruciate Ligament (PCL), Lateral Collateral Ligament (LCL), and Medial Collateral Ligament (MCL). The ligaments are modeled as nonlinear elastic strips (they do not …

Anatomy, Implant Selection And Placement Influence Spine Mechanics Associated With Total Disc Replacement, Justin F.M. Hollenbeck

Electronic Theses and Dissertations

Through aging and injury, the intervertebral disc of the lumbar spine can undergo degeneration, leading to collapse of the vertebrae and low back pain, a symptom that affects half the adult population in any given year. In an effort to reduce low back pain, total disc replacement treatment removes the degenerated disc, restores natural height and lordosis of the segment, and preserves motion at the joint. Patient anatomy, implant selection, and implant placement play significant roles in a patient's outcomes after total disc replacement surgery. Thus, the objective of the work presented in this thesis was to develop a suite …

Finite Element And Probabilistic Analysis Of Soft Tissue Structures Of The Human Lumbar Spine, Dana Joseph Coombs

Electronic Theses and Dissertations

Human lumbar spine mechanics are influenced by soft tissue structures. Understanding and properly modeling these structures can help determine pathology, treatment, and implant design and performance. Finite element models of the L4-L5 level of the lumbar spine are often used, which include a representation of the intervertebral disc and spinal ligaments. Validation of these models are typically based on torque rotation data from a single subject or the models use average properties reported in literature. However, experimental testing reports variation up to 40% in ligament stiffness and even greater variability for annulus fibrosis properties. Probabilistic approaches enable consideration of the …

An Immersed Boundary Geometric Preprocessor For Arbitrarily Complex Terrain And Geometry, Inanc Senocak, Micah Sandusky, Rey Deleon, Derek Wade, Kyle Felzien, Marianna Budnikova

Mechanical and Biomedical Engineering Faculty Publications and Presentations

There is a growing interest to apply the immersed boundary method to compute wind fields over arbitrarily complex terrain. The computer implementation of an immersed boundary module into an existing flow solver can be accomplished with minor modifications to the rest of the computer program. However, a versatile preprocessor is needed at the first place to extract the essential geometric information pertinent to the immersion of an arbitrarily complex terrain inside a 3D Cartesian mesh. Errors in the geometric information can negatively impact the correct implementation of the immersed boundary method as part of the solution algorithm. Additionally, the distance …

Biomechanical Investigation Of Elite Place-Kicking, Chase M. Pfeifer

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Many studies aim to understand the fundamentals of kicking commonly displayed by soccer players [4,6,10,16,17,18,24,25,28,29,30,34,36,38,40]. Of those studies, most are limited to a two-dimensional (2D) analysis using high-speed cameras for position tracking or utilizing electromyography to observe the activity of select muscles [4,6,18,25,29,36]. The few studies that investigate kicking using a three-dimensional (3D) model are limited in their position tracking capabilities and focus mainly on joint flexion potentials and foot speed.

This dissertation is a comprehensive biomechanical analysis (kinematic and EMG) of the field-goal place-kicking techniques of four elite kickers in American football. Data were compared and contrasted with ball …

Indentation Probing Of In Vitro Bovine Articular Cartilage: Effects On Chondrocyte Viability And Tissue Biomechanics, Pablo F. Argote, Alan Poon, Xin Xu Ph.D, Corey P. Neu Ph.D.

The Summer Undergraduate Research Fellowship (SURF) Symposium

Osteoarthritis (OA) consists of a degenerative disease on articular cartilage, which is prone to excessive mechanical loading and frictional resistance that leads to the wear and tear of the tissue. These factors result in the progressive and incurable disease that affects millions of people worldwide. The goal is to characterize chondrocyte viability and the in vitro biomechanical properties of articular cartilage in two confined indentation studies. One study looks at the chondrocyte viability over seven days. The second compares the immediate effects of strain rates on chondrocyte viability and tissue biomechanics. Bovine cartilage explants are harvested, cultured, and then 40% …

A Community Of World Class Engineering Students, Devshikha Bose, Krishna Pakala

Mechanical and Biomedical Engineering Faculty Publications and Presentations

This paper is a work in progress report on an Engineering Living Learning Community (LLC) at Boise State University. Though the LLC under consideration is for the time period of Fall 2014 to Fall 2016, this report is limited to student as well as instructor anecdotal and self-reported experiences, observations, and evaluations made during Fall 2014 and Spring 2015. The mission of the Residential College program at BSU is to integrate student academic and personal life in a residential setting, so as to develop interdisciplinary knowledge, foster deep learning, and maximize student success. In support of this goal, students completed …

Nano Scale Mechanical Analysis Of Biomaterials Using Atomic Force Microscopy, Diganta Dutta

Mechanical & Aerospace Engineering Theses & Dissertations

The atomic force microscope (AFM) is a probe-based microscope that uses nanoscale and structural imaging where high resolution is desired. AFM has also been used in mechanical, electrical, and thermal engineering applications. This unique technique provides vital local material properties like the modulus of elasticity, hardness, surface potential, Hamaker constant, and the surface charge density from force versus displacement curve. Therefore, AFM was used to measure both the diameter and mechanical properties of the collagen nanostraws in human costal cartilage. Human costal cartilage forms a bridge between the sternum and bony ribs. The chest wall of some humans is deformed …

Synergy-Based Two-Level Optimization For Predicting Knee Contact Forces During Walking, Gil Serrancolí, Allison Kinney, Josep M. Font-Llagunes, Benjamin J. Fregly

Mechanical and Aerospace Engineering Faculty Publications

Musculoskeletal models and optimization methods are combined to calculate muscle forces. Some model parameters cannot be experimentally measured due to the invasiveness, such as the muscle moment arms or the muscle and tendon lengths. Moreover, other parameters used in the optimization, such as the muscle synergy components, can be also unknown. The estimation of all these parameters needs to be validated to obtain physiologically consistent results. In this study, a two-step optimization problem was formulated to predict both muscle and knee contact forces of a subject wearing an instrumented knee prosthesis. In the outer level, muscle parameters were calibrated, whereas …

Development Of A Muscle Model Parameter Calibration Method Via Passive Muscle Force Minimization, Allison Kinney, Benjamin J. Fregly

Mechanical and Aerospace Engineering Faculty Publications

Computational predictions of subject-specific muscle and knee joint contact forces during walking may improve individual rehabilitation treatment design. Such predictions depend directly on specified model parameter values. However, model parameters are difficult to measure non-invasively. Methods for muscle model parameter calibration have been developed previously. However, it is currently unknown how the musculoskeletal system chooses muscle model parameter values. Previous studies have hypothesized that muscles avoid injury during walking by generating little passive force and operating in the ascending region of the force-length curve. This hypothesis suggests that muscle model parameter values may be selected by the body to minimize …

Computational Prediction Of Remodeling Of Collagen Fiber Network In Articular Cartilage Under Dynamic Unconfined Compression, Juan Andres Coello Amado

Theses and Dissertations - UTB/UTPA

A poroelastic finite element model of a heterogeneous cartilage disk was created based on previous studies and experimental setups; this allows us to study cartilage behavior under dynamic unconfined compression. Previous studies have used a Post Hoc approach, which consist of searching for patterns or relationships between predicted mechanical parameters obtained through computational and experimental results. Our goal in this study is to take the same Post-Hoc approach and identify patterns between predicted mechanical parameters, such as fiber strain or stress, and experimentally-measured collagen fiber distribution (i.e. reorientation of fibers under dynamic unconfined compression). After computational predictions were obtained, it …

Use Of Mobile Learning Strategies And Devices For E-Portfolio Content Creation In An Engineering Thermodynamics And Fluid Mechanics Classes: Student Perceptions, Devshikha Bose, Krishna Pakala

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Use of mobile learning strategies and devices for e-portfolio content creation in an engineering Thermodynamics class: Student perceptions Mobile devices can be useful for creating educational content and to help students to learn better (Benedict & Pence, 2012; Tabor & Minch, 2013; Pereira, Echeazarra, Sanz-Santamaria, & Gutierrez, 2014). The purpose of this study is to determine student perceptions on the efficacy of using mobile learning strategies and devices to create electronic content for inclusion in an engineering individual e-portfolio. Students enrolled in an undergraduate 300-level engineering Thermodynamics class, created multimedia videos and produced content demonstrating course content summaries, problem solving …

Development And Validation Of A Tibiofemoral Joint Finite Element Model And Subsequent Gait Analysis Of Intact Acl And Acl Deficient Individuals, Nicholas Czapla

Master's Theses

Osteoarthritis (OA) is a degenerative condition of articular cartilage that affects more than 25 million people in the US. Joint injuries, like anterior cruciate ligament (ACL) tears, can lead to OA due to a change in articular cartilage loading. Gait analysis combined with knee joint finite element modeling (FEM) has been used to predict the articular cartilage loading. To predict the change of articular cartilage loading during gait due to various ACL injuries, a tibiofemoral FEM was developed from magnetic resonance images (MRIs) of a 33 year male, with no prior history of knee injuries. The FEM was validated for …

Sapien3 Comb Stitch Improvement For Edwards Lifesciences, William Harley, Thomas Pluschkell, John Mctigue, Garrett Reed

Mechanical Engineering

The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Transcatheter Heart Valve Subassembly Device, Adam Aslam, Matthew Bezkrovny, Daniel Degree

Mechanical Engineering

No abstract provided.

The Influence Of Neuromusculoskeletal Model Calibration Method On Predicted Knee Contact Forces During Walking, Gil Serrancolí, Allison Kinney, Benjamin J. Fregly, Josep M. Font-Llagunes

Mechanical and Aerospace Engineering Faculty Publications

This study explored the influence of three model calibration methods on predicted knee contact and leg muscle forces during walking. Static optimization was used to calculate muscle activations for all three methods. Approach A used muscle-tendon model parameter values (i.e., optimal muscle fiber lengths and tendon slack lengths) taken directly from literature. Approach B used a simple algorithm to calibrate muscle-tendon model parameter values such that each muscle operated within the ascending region of its normalized force-length curve. Approach C used a novel two-level optimization procedure to calibrate muscle-tendon, moment arm, and neural control model parameter values while simultaneously predicting …

Computational Fluid Dynamics Applied To The Analysis Of Blood Flow Through Central Aortic To Pulmonary Artery Shunts, Carey Celestin Jr

LSU New Orleans Theses and Dissertations

This research utilizes CFD to analyze blood flow through pathways representative of central shunts, commonly used as part of the Fontan procedure to treat cyanotic heart disease. In the first part of this research, a parametric study of steady, Newtonian blood flow through parabolic pathways was performed to demonstrate the effect that flow pathway curvature has on wall shear stress distribution and flow energy losses. In the second part, blood flow through two shunts obtained via biplane angiograms is simulated. Pressure boundary conditions were obtained via catheterization. Results showed that wall shear stresses were of sufficient magnitude to initiate platelet …

Towards A Dynamic Clamp For Neurochemical Modalities, C. M. Rivera, H.-J. Kwon, A. Hashmi, Gu Yu, J. Zhao, J. Gao, J. Xu, Wei Xue, A. G. Dimitrov

Henry M. Rowan College of Engineering Departmental Research

The classic dynamic clamp technique uses a real-time electrical interface between living cells and neural simulations in order to investigate hypotheses about neural function and structure. One of the acknowledged drawbacks of that technique is the limited control of the cells’ chemical microenvironment. In this manuscript, we use a novel combination of nanosensor and microfluidic technology and microfluidic and neural simulations to add sensing and control of chemical concentrations to the dynamic clamp technique. Specifically, we use a microfluidic lab-on-a-chip to generate distinct chemical concentration gradients (ions or neuromodulators), to register the concentrations with embedded nanosensors and use the processed …

Characterization And Evaluation Of Head Impact Sensors And Varsity Football Helmets, Brian R. Cummiskey

Open Access Theses

An increased understanding of the effects of brain injury in recent years has led to greater attention being given to the topic. A desire to investigate the causal agents of these injuries in athletes has led to the development and use of several devices that track head impacts as well as improving helmet technology to protect players from said impacts. In order to determine which devices are able to best measure head impacts, a Hybrid III headform was used to quantify the accuracy for translational and angular accelerations. Testing was performed by means of administering impacts to a helmet on …

Freezing-Induced Deformation Of Biomaterials In Cryomedicine, Altug Ozcelikkale

Open Access Dissertations

Cryomedicine utilizes low temperature treatments of biological proteins, cells and tissues for cryopreservation, materials processing and cryotherapy. Lack of proper understanding of cryodamage that occurs during these applications remains to be the primary bottleneck for development of successful tissue cryopreservation and cryosurgery procedures. An engineering approach based on a view of biological systems as functional biomaterials can help identify, predict and control the primary cryodamage mechanisms by developing an understanding of underlying freezing-induced biophysical processes. In particular, freezing constitutes the main structural/mechanical origin of cryodamage and results in significant deformation of biomaterials at multiple length scales. Understanding of these freezing-induced …