Polymer and Organic Materials Commons^™

Effect Of Curing Rate On The Microstructure And Macroscopic Properties Of Epoxy Fiberglass Composites, Ammar Patel, Olesksandr Kravchenko, Ica Manas-Zloczower

Mechanical & Aerospace Engineering Faculty Publications

Curing rates of an epoxy amine system were varied via different curing cycles, and glass-fiber epoxy composites were prepared using the same protocol, with the aim of investigating the correlation between microstructure and composite properties. It was found that the fast curing cycle resulted in a non-homogenous network, with a larger percentage of a softer phase. Homogenized composite properties, namely storage modulus and quasi-static intra-laminar shear strength, remained unaffected by the change in resin microstructure. However, fatigue tests revealed a significant reduction in fatigue life for composites cured at fast curing rates, while composites with curing cycles that allowed a …

Usage Of Fomblin Y To Improve Water Repellence Of Surface Coatings, Shawn Pj Kirby, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Fluoro-Decyl POSS (FDP) has shown strong potential as a water repellant surface coating. Additionally, Fomblin is a solvent believed to have the ability to control the crystallization of POSS compounds on surfaces. Controlling the crystallization is key to improving water repelling abilities of surfaces. Thus, dip coating FDP and Fomblin onto surfaces is being investigated for water repulsion, mechanical stability, and deposition feasibility. First, temperature dependence of solubility of Fluoro-Decyl POSS in Fomblin was tested using Dynamic Light Scattering. Relative water repelling abilities of different coatings were determined by measuring contact angle of surfaces with water. Coatings with and without …

Comparative Solubility Of Poss Compounds In Fomblin Y, Shawn Pj Kirby, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Fluoro-Decyl POSS (FDP) has shown strong potential as a water repellant surface coating. Additionally, Fomblin is a solvent believed to have the ability to control the crystallization of POSS compounds on surfaces. Controlling the crystallization is key to improving water repelling abilities of surfaces. Thus, dip coating FDP and Fomblin onto surfaces is being investigated for water repulsion, mechanical stability, and deposition feasibility. However, in order for this to be successful, POSS must be soluble in Fomblin. Temperature dependence of solubility of Fluoro-Hexyl, Fluoro-Octyl, Fluoro-Decyl POSS in Fomblin was tested using Dynamic Light Scattering. The values were compared, and it …

Cellulose Reinforced Thermoplastic Composites By In-Situ Ring-Opening Polymerization, Shahab Kashani Rahimi

Dissertations

Over the past two decades, the increasing concern about the negative environmental impacts of synthetic materials has led to rising interests in utilizing renewable natural resources to develop polymer materials with comparable properties and performance to their synthetic counterparts. One of the major fields of interest is polymer composites where the replacement of synthetic fibers with bio renewable natural fibers is of great potential. However, the processing difficulties, in terms of fiber dispersion and thermal stability have limited the application of cellulosic fibers to polymers with low processing temperatures which are mostly hydrophobic polymers. As a result, the true reinforcing …

Synthesis,Structure And Properties Of Ruthenium Polypyridyl Metalloligand Based Metal-Organic Frameworks, Mamatha Polapally

Masters Theses & Specialist Projects

Metal-organic frameworks (MOFs) have been extensively studied because of their amazing applications in gas storage, purification, photocatalysis, chemical sensing, and imaging techniques. Ruthenium polypyridyl complexes have been broadly considered as photosensitizers for the conversion of solar energy and photoelectronic materials. With this aspect, we have synthesized three new ruthenium polypyridyl based MOFs ([Ru(H2bpc)Cu(bpc)(Hbpc)2(H2O)]·5H2O (1), [Ru(H2bpc)(Fe(bpc)(Hbpc)2(H2O)2]·6H2O (2) and [Ru(H2bpc)Ni(bpc)(Hbpc)2(H2O)2]·6H2O (3)) from ruthenium(III) chloride, bpc (2,2’- bipyridine-4,4’-dicarboxylic acid) ligand, and 3d M(II) metal ions (M(II)= Cu(II), Fe(II), Ni(II)). These MOFs were synthesized under hydro or solvothermal conditions by using water, ethanol or methanol as solvents. The crystal structures of the new compounds …

An Investigation Of The Use Of Cerium And Polyhedral Oligomeric Silsesquioxanes For The Protection Of Polymeric Epoxy Compounds In The Low Earth Orbit Environment, Jessica Miriam Piness

Dissertations

Low Earth orbit presents many hazards for composites including atomic oxygen, UV radiation, thermal cycling, micrometeoroids, and high energy protons. Atomic oxygen and vacuum ultraviolet radiation are of concern for space-bound polymeric materials as they degrade the polymers used as matrices for carbon fiber composites, which are used in satellites and space vehicles due to their high strength to weight ratios. Epoxy-amine thermosets comprise a common class of matrix due to processability and good thermal attributes. Polyhedral oligomeric silsesquioxanes (POSS) have shown the ability to reduce erosion in polyimides, polyurethanes, and other polymers when exposed to atomic oxygen. The POSS …

Formation Of Nanostructured Epoxy Networks Containing Polyhedral Oligomeric Silsesquioxane (Poss) And Silica Nanoparticles, Amit K. Sharma

Dissertations

This dissertation is focused on structure-property-processing relationship studies based on well-defined polyhedral oligomeric silsesquioxane (POSS) modified epoxy networks to present a comprehensive understanding of hybrid network behavior. In this research, a monoamine functional POSS molecule is incorporated into the epoxy monomer as pendant unit to mimic common epoxy structures and then crosslinked to form well-defined epoxy hybrid networks. The POSS cages behave as nanosized pendant unit in the epoxy matrices, while the mass fraction of POSS cages is varied and the effects on physical properties are examined with respect to changes in network architecture.

A novel continuous reactor method is …

Polyisobutylene Telechelic Prepolymers By In Situ End-Quenching And Post-Polymerization Modifications, Bin Yang

Dissertations

This volume focuses on the development of telechelic polyisobutylene (PIB) prepolymers by combining end-capping of living carbocationic polymerization of isobutylene (IB) with suitable reactants and post-polymerization modifications. Alkylation kinetics of PIB tert-chloride with alkoxybenzenes using either TiCl₄ or AlCl₃ were investigated. Quantitative para-position end-capped products were only achieved if the alkoxybenzene/AlCl₃ molar ratio was greater than unity; while no such molar ratio is required for TiCl₄, but the alkylation rate was slower than AlCl₃ under the same conditions. Photopolymerization kinetics analysis of PIB triphenol tri(meth)acrylates with low and high M_ns, …

Design And Synthesis Of Polymer Brush Surfaces With Complex Molecular Architectures And Morphologies, Wei Guo

Dissertations

The combination of surface-initiated polymerization (SIP) and postpolymerization modification (PPM) is a powerful technique for the fabrication of functional soft surfaces. Better understanding the influence of the aforementioned factors on the PPM effectiveness is valuable for fulfilling the potential of the PPM approach for the fabrication of functional soft surfaces. Specifically, by carefully balancing modification reactivity and limitation of mass transport, polymer brush with composition heterogeneity and gradient along the normal direction of the surface otherwise unattainable by methods of direct polymerization can be fabricated via the PPM approach which opens doors to new routes to polymer brush with complex …

Effect Of Chain Rigidity On Network Architecture And Deformation Behavior Of Glassy Polymer Networks, Kyler Reser Knowles

Dissertations

Processing carbon fiber composite laminates creates molecular-level strains in the thermoset matrix upon curing and cooling which can lead to failures such as geometry deformations, micro-cracking, and other issues. It is known strain creation is attributed to the significant volume and physical state changes undergone by the polymer matrix throughout the curing process, though storage and relaxation of cure-induced strains remain poorly understood. This dissertation establishes two approaches to address the issue. The first establishes testing methods to simultaneously measure key volumetric properties of a carbon fiber composite laminate and its polymer matrix. The second approach considers the rigidity of …

Structure-Property Relationships Of Polyisobutylene-Block-Polyamide Thermoplastic Elastomers, Morgan Dunn Heskett

Master's Theses

Thermoplastic elastomers (TPEs) are a class of polymer fit for a wide variety of applications due to their customizability. In the synthesis of these types of materials, an elastically-performing polymer, deemed the “soft block,” is combined with a stiffer “hard block” polymer, each of which can be selected based on their own specific properties in order to achieve desired material behavior in the final copolymer. Recently, the use of polyisobutylene as a soft block in combination with a polyamide hard block has been investigated for use in TPE synthesis. While the material showed some promising behavior, many properties were still …

Design And Synthesis Of Dynamic Covalent Polymer Scaffolds With Controlled Architectures, Emily Annette Hoff

Dissertations

The design and synthesis of functional, controlled polymer architectures is essential to the development of new materials with precise and tailorable properties or applications. The work described in this dissertation focuses on the development of controlled polymer architectures with dynamic linkages for the design of multifunctional materials and surfaces via robust, efficient, and stimuli-responsive strategies.

In Chapter III, a post-polymerization modification strategy based on ambient temperature nucleophilic chemical deblocking of polymer scaffolds bearing N-heterocycle blocked isocyanate moieties is reported. Room temperature RAFT polymerization of three azole-N-carboxamide methacrylates, including 3,5-dimethyl pyrazole, imidazole, and 1,2,4-triazole derivatives, afforded reactive polymer scaffolds …

Spray Printing Of Organic Semiconducting Single Crystals, Grigorios-Panagiotis Rigas, Marcia M. Payne, John E. Anthony, Peter N. Horton, Fernando A. Castro, Maxim Shkunov

Chemistry Faculty Publications

Single-crystal semiconductors have been at the forefront of scientific interest for more than 70 years, serving as the backbone of electronic devices. Inorganic single crystals are typically grown from a melt using time-consuming and energy-intensive processes. Organic semiconductor single crystals, however, can be grown using solution-based methods at room temperature in air, opening up the possibility of large-scale production of inexpensive electronics targeting applications ranging from field-effect transistors and light-emitting diodes to medical X-ray detectors. Here we demonstrate a low-cost, scalable spray-printing process to fabricate high-quality organic single crystals, based on various semiconducting small molecules on virtually any substrate by …

Molecular Tetrapods For Optoelectronic Applications, Jianzhong Yang

Chemistry and Chemical Biology ETDs

Most conjugated molecules including polymers and small molecules applied in organic solar cells (OSCs) have linear structures containing multiple aromatic groups connected in series. However, unfavorable film forming ability and grain boundaries both originated from high crystallinity of linear small molecules are detrimental to device performances. Thus, among multi-dimensional structures, tetrapodal molecules are especially interesting owing to their unique ability to mutually interlock, which prevents dislodging and provides high structural stabilities. Such molecular design can also increase absorption cross-sections and provide more extensively percolating pathways for charge transport, making such molecular tetrapods promising in OSCs applications. In my dissertation, I …

Correlation Of Polymer Performance And Hansen Solubility Parameters, Daniel Jobse Mania

Master's Theses

Ready-to-use (RTU) grout is becoming more important to the finish and remodeling construction industry. Market research shows it is a fast-growing product that not only is creating its own space, but is beginning to supplant existing technology.

The original intent of this research was to investigate formulation parameters and how they affect grout performance. It was learned that particle size and oil absorption (OA) value are important filler properties that affect performance as much as adequate packing density and optimal pigment volume concentration (PVC) without going beyond critical PVC (CPVC).

Polymer architecture was also determined to be extremely important, but …

Synthesis Of Acceptors For Use In Donor-Acceptor Copolymers And Characterization Of These Polymers, William D. Walker

Honors Theses

In this thesis, a selenium-derivatized acceptor was synthesized to examine the heavy atom effects of selenium on the position of the frontier molecular orbitals (HOMO/LUMO band gap) as opposed to sulfur in a donor-acceptor copolymer for use in light harvesting and detection applications. Over the course of this research, standard operating protocols for ultraviolet-visible (UV-Vis-NIR) and Fourier transform infrared (FT-IR) spectroscopies, as well as cyclic voltammetry (CV) characterization techniques were established. Once synthesized, the polymers were characterized through use of the established characterization protocols. The selenium-derivatized polymer exhibited a bathochromic shift compared to the sulfur analogue, with a solid-state absorption …

Strain Effects On The Work Function Of An Organic Semiconductor, Yanfei Wu, Annabel R. Chew, Geoffrey A. Rojas, Gjergji Sini, Greg Haugstad, Alex Belianinov, Sergei V. Kalinin, Hong Li, Chad Risko, Jean-Luc Brédas, Alberto Salleo, C. Daniel Frisbie

Chemistry Faculty Publications

Establishing fundamental relationships between strain and work function (WF) in organic semiconductors is important not only for understanding electrical properties of organic thin films, which are subject to both intrinsic and extrinsic strains, but also for developing flexible electronic devices. Here we investigate tensile and compressive strain effects on the WF of rubrene single crystals. Mechanical strain induced by thermal expansion mismatch between the substrate and rubrene is quantified by X-ray diffraction. The corresponding WF change is measured by scanning Kelvin probe microscopy. The WF of rubrene increases (decreases) significantly with in-plane tensile (compressive) strain, which agrees qualitatively with density …

The Role Of Microbial Exopolymers In Determining The Fate Of Oil And Chemical Dispersants In The Ocean, Antonietta Quigg, Uta Passow, Wei-Chun Chin, Chen Xu, Shawn Doyle, Laura Bretherton, Manoj Kamalanathan, Alicia K. Williams, Jason B. Sylvan, Zoe V. Finkel, Anthony H. Knap, Kathleen A. Schwehr, Saijin Zhang, Luni Sun, Terry L. Wade, Wassim Obeid, Patrick G. Hatcher, Peter H. Santschi

Chemistry & Biochemistry Faculty Publications

The production of extracellular polymeric substances (EPS) by planktonic microbes can influence the fate of oil and chemical dispersants in the ocean through emulsification, degradation, dispersion, aggregation, and/or sedimentation. In turn, microbial community structure and function, including the production and character of EPS, is influenced by the concentration and chemical composition of oil and chemical dispersants. For example, the production of marine oil snow and its sedimentation and flocculent accumulation to the seafloor were observed on an expansive scale after the Deepwater Horizon oil spill in the Northern Gulf of Mexico in 2010, but little is known about the underlying …

Optimizing Solvent Blends For A Quinary System, Thomas L. Hoy

Williams Honors College, Honors Research Projects

The Department of Polymer Engineering had received a grant from the Keck foundation to produce a process in which hundreds of copolymers can be formulated, synthesized, analyzed and then extrapolated to produce the optimal polymer for the desired material property. This process involves synthesizing approximately fifty polymers in a custom apparatus, none of which necessarily have the same monomer components. This leads to issue of which solvent or blend of solvents to use that would sufficiently dissolve both monomers and the resulting copolymer. If the monomers are not completely dissolved, a homogenous reaction will be impossible and if the copolymer …

Hybrid Aryl-Ether-Ketone And Hyperbranched Epoxy Networks, John Misasi

Dissertations

In this dissertation, relationships between chemical structures, cure kinetics and network architectures are correlated to bulk mechanical properties for novel, hybrid epoxy-amine networks. The work is split into two primary sections: the first is the synthesis and characterization of multifunctional glassy networks based on aryl-ether-ketone diamine curatives, while the second is based on the synthesis and characterization of hyperbranched epoxy polymers and their resulting networks.

Three aryl-ether-ketone (AEK) diamines of increasing molecular weights were synthesized and used to cure 4,4’-tetraglycidylether of diaminodiphenylmethane (TGDDM); the resulting networks were compared to 4,4’-diaminodiphenyl sulfone cured TGDDM. Architectural differences were created by varying cure …

Development Of Dual-Cure Hybrid Polybenzoxazine Thermosets, Jananee Narayanan Sivakami

Dissertations

Polybenzoxazines are potential high performance thermoset replacements for traditional phenolic resins that can undergo an autocatalytic, thermally initiated ring - opening polymerization, and possess superior processing advantages including excellent shelf-life stability, zero volatile loss and limited volumetric shrinkage. The simplistic monomer synthesis and availability of a wide variety of inexpensive starting materials allows enormous molecular design flexibility for accessing a wide range of tailorable material properties for targeted applications. Despite the fact, once fully cured, benzoxazines are difficult to handle due to their inherent brittleness, leaving a very little scope for any modifications. The motivation of this dissertation is directed …

Synthesis, Characterization, And Thermoelectric Properties Of Radical Siloxanes, Arnold J. Eng, Bryan Boudouris, Edward P. Tomlinson, Martha Emily Hay

The Summer Undergraduate Research Fellowship (SURF) Symposium

More than half of the annual energy consumption in the United States is lost as waste heat. Polymer-based thermoelectric devices have the potential to utilize this waste heat both sustainably and cost-effectively. Although conjugated polymers currently dominate research in organic thermoelectrics, the potential of using polymers with radical pendant groups have yet to be realized. These polymers have been found to be as conductive as pristine (i.e., not doped) poly(3-hexylthiophene) (P3HT), a commonly-used charge-transporting conjugated polymer. This could yield promising avenues for thermoelectric material design as radical polymers are more synthetically tunable and are hypothesized to have a high Seebeck …

Morphology-Property Relationship For Binary Organic Thin Films, Alyssa Lynn Griffin

Master's Theses

Organic thin films can be readily mass-produced through solution-based fabrication methods including ink-printing and solution-casting because their light weight, flexibility, and inexpensive sources. Their applications range from organic field-effect transistors (OFET), organic solar cells (OSC), to organic light emitting diodes (OLEDs). Compared with pure component films, binary organic thin films (BOTF) allows for novel characteristics and specialized features to handle more demanding tasks. Due to the complex intermolecular interactions in BOTF, various microscopic phases with different morphological and electronic properties may be formed and this information is difficult to extract through conventional bulk measurements.

Organic thin films can be readily …

Effect Of Surfactant Architecture On Conformational Transitions Of Conjugated Polyelectrolytes, Greg A. Braggin

Master's Theses

Water soluble conjugated polyelectrolytes (CPEs), which fall under the category of conductive polymers, possess numerous advantages over other conductive materials for the fabrication of electronic devices. Namely, the processing of water soluble conjugated polyelectrolytes into thin film electronic devices is much less costly as compared to the processing of inorganic materials. Moreover, the handling of conjugated polyelectrolytes can be performed in a much more environmentally friendly manner than in the processing of other conjugated polymers because conjugated polyelectrolytes are water soluble, whereas other polymers will only dissolve in toxic organic solvents. The processing of electronic devices containing inorganic constituents such …

Utilization Of Aqueous Raft Prepared Copolymers To Improve Anticancer Drug Efficacy, Andrew Christopher Holley

Dissertations

The advent of controlled radical polymerization (CRP) techniques, along with advancements in facile conjugation chemistry, now allow synthetic tailoring of precise, polymeric architectures necessary for drug/gene delivery. Reversible addition- fragmentation chain transfer (RAFT) polymerization and its aqueous counterpart (aRAFT) afford quantitative control over key synthetic parameters including block length, microstructure, and placement of structo-pendent and structo-terminal functionality for conjugation of active agents and targeting moieties. The relevance of water-soluble and amphiphilic (co)polymers synthesized by RAFT for in vitro delivery of therapeutics in biological fluids is an especially attractive feature. In many cases, polymerization, binding, conjugation, …

Study Of The Structure-Property Relationships That Determine The Effects Of Latexes And Starch Containing Latex Emulsions On The Performance Of The Barrier Coatings (Sub-Coat) For Paper, Joanna Marie Monfils

Master's Theses

The history of carbonless paper dates back to the 1940s. Before this, a carbon copy sheet was needed between sheets of paper to be able to produce one or more copies simultaneously during writing. The pressure from a pen or typewriter would help deposit the ink of the carbon paper onto the blank sheet of paper under the original written sheet to create a “carbon copy.” This method did however, have its disadvantages. Not only did it produce a limited number of copies, but it was also a messy process. So came the creative process of using microencapsulated dyes to …

Addressing Public Health Risks Of Persistent Pollutants Through Nutritional Modulation And Biomimetic Nanocomposite Remediation Platforms, Bradley J. Newsome

Theses and Dissertations--Chemistry

Due to their relative chemical stability and ubiquity in the environment, chlorinated organic contaminants such as polychlorinated biphenyls (PCBs) pose significant health risks and enduring remediation challenges. Engineered nanoparticles (NPs) provide a novel platform for sensing/remediation of these toxicants, in addition to the growing use of NPs in many industrial and biomedical applications, but there remains concern for their potential long-term health effects. Research highlighted herein also represents a transdisciplinary approach to address human health challenges associated with exposure to PCBs and NPs. The objectives of this dissertation research are two-fold, 1) to develop effective methods for capture/sensing and remediation …

Semiconductor Nanocrystals: From Quantum Dots To Quantum Disks, Zheng Li

Graduate Theses and Dissertations

The bottom-up colloidal synthesis opened up the possibility of finely tuning and tailoring the semiconductor nanocrystals. Numerous recipes were developed for the preparation of colloidal semiconductor nanocrystals, especially the traditional quantum dots. However, due to the lack of thorough understanding to those systems, the synthesis chemistry is still on the empirical level. CdS quantum dots synthesis in non-coordinating solvent were taken as a model system to investigate its molecular mechanism and formation process, ODE was identified as the reducing agent for the preparation of CdS nanocrystals, non-injection and low-temperature synthesis methods developed. In this model system, we not only proved …

Active Response Of Polymer Materials From External Stimuli – Solvents And Light; Grafting Reactions On Perovskite Layers, Jianxia Zhang

LSU New Orleans Theses and Dissertations

The active response of a series of polymeric materials was investigated. Both solvent activated and light activated thin films and wire systems show dynamic behaviors when exposed to different stimuli.

Solvent mediated fluxional behavior of polymer thin films involved extensive, rapid curling both on infusion and evaporation of good solvents. These films can be either lab-fabricated ones or commercial ones, and the curling behavior can be as fast as seconds. Conditions including polymer materials, chosen solvents, and film geometry can affect the behavior.

Methods that allowed for the creation and retention of distorted wire structures were also developed; the asymmetric …

Cross-Linked Pdms Expansion Due To Submersion In Liquid And Supercritical Co2, Teng Yang

Graduate Theses and Dissertations

Characterization of micro/nano-copper particles impregnated Polydimethylsiloxane (PDMS) submersed in supercritical carbon dioxide (scCO2) was studied. The purpose of this investigation was to advance micro-corrosion sensor technology utilizing PDMS and micro-metal particle composite as the sensing element currently under-development. One of the key challenges encountered was the removal of the native oxides inherently existing on the metal particles. Numerous techniques were experimented with to counter this problem at the UA Engineered Micro/Nano Systems Laboratory (EMNSL), with swell-based protocols being identified as the most promising solution. In terms of compatibility to Micro-electro-mechanical Systems (MEMS) fabrication, CO2 is often used in the release …