Polymer and Organic Materials Commons^™

Establishing Independent Tunability Of The Mechanical And Transport Properties Of Polymer Gels, Lucas Rankin

Master’s Theses

Polymer gels can be used in the fabrication of materials for filtering liquid and gaseous media, solid-state electrolytes, and transdermal medical patches. This diverse range of applications primarily relies on the transport and mechanical properties of polymer gels. Both sets of properties have shown excellent tunability, but typically in a coupled fashion. Establishing the independent tunability of the transport and mechanical properties of polymer gels (using simple, cost-effective methods) is paramount if polymer gels are to be used to their full potential. Specifically, block copolymer gels self-assemble into organized nanoscale networks within the gel solvent, which allows for facile control …

Multi-Level Analysis Of Atomic Layer Deposition Barrier Coatings On Additively Manufactured Plastics For High Vacuum Applications, Nupur Bihari

Dissertations, Master's Theses and Master's Reports

While hardware innovations in micro/nano electronics and photonics are heavily patented, the rise of the open-source movement has significantly shifted focus to the importance of obtaining low-cost, functional and easily modifiable research equipment. This thesis provides a foundation of open source development of equipment to aid in the micro/nano electronics and photonics fields.

First, the massive acceptance of the open source Arduino microcontroller has aided in the development of control systems with a wide variety of uses. Here it is used for the development of an open-source dual axis gimbal system. This system is used to characterize optoelectronic properties of …

In Depth Characterisation Of The Biomolecular Coronas Of Polymer Coated Inorganic Nanoparticles With Differential Centrifugal Sedimentation, André Perez-Potti, Hender Lopez, Beatriz Pelaz, Abuelmagd Abdelmonem, Mahmoud G. Soliman, Ingmar Schoen, Philip M. Kelly, Kenneth A. Dawson, Wolfgang J. Parak, Zeljka Krpetic, Marco P. Monopoli

Articles

Advances in nanofabrication methods have enabled the tailoring of new strategies towards the controlled production of nanoparticles with attractive applications in healthcare. In many cases, their characterisation remains a big challenge, particularly for small-sized functional nanoparticles of 5 nm diameter or smaller, where current particle sizing techniques struggle to provide the required sensitivity and accuracy. There is a clear need for the development of new reliable characterisation approaches for the physico-chemical characterisation of nanoparticles with significant accuracy, particularly for the analysis of the particles in the presence of complex biological fluids. Herein, we show that the Differential Centrifugal Sedimentation can …

Practical Adhesion Measurements In Organic Coatings; Advancing Understanding And Mechanical Methods Development, Diana Gottschalk

Dissertations

“Adhesion” can be considered either a mechanical or chemical phenomenon. The mechanical interpretation describes the difficulty of separating surfaces and is useful for quantifying performance within applications that depend on bulk and interfacial properties. Chemical adhesion describes interfacial resistance to chemical attack and does not depend on bulk properties. Predicting chemical failure through mechanical measurement is confounded by the influence of bulk properties. However, the prospect is attractive because of the robust tolerance for sample geometries, allowing experiments to resemble an end-use system. The present work's primary goal was to elevate mechanical methods to provide a detailed interfacial characterization of …

Spatially Directed Functionalization By Co-Electropolymerization Of Two 3,4-Ethylenedioxythiophene Derivatives On Microelectrodes Within An Array, Benjamin J. Jones, Carol Korzeniewski, Jefferson H. Franco, Shelley D. Minteer, Ingrid Fritsch

Chemistry & Biochemistry Faculty Publications and Presentations

Electrodeposited conductive copolymer films with predictable relative properties (quantities of functional groups for further modification and capacitance) are of interest in sensors, organic electronic materials and energy applications. Potentiodynamic copolymerization of films in aqueous solutions of two different thiophene derivatives, (2,3-dihydrothieno[3,4-b]dioxin-2-yl) methanol (1) and 4-((2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl)-methoxy)-4-oxobutanoic acid (2), containing 0.02 M total monomer (0, 25, 34, 50, 66, 75, 100 mol% 2), 0.05 M sodium dodecyl sulfate, and 0.1 M LiClO4, on gold microelectrodes in an array was investigated. Decreasing monomer deposited (m) from 0 to 100 mol% 2 is attributed to a decreasing pH that inhibits electropolymerization. Molar ratios of …

Preparation And Characterisation Of Heat Treated Oil Palm-Empty Fruit Bunch/High Density Polyethylene Composites, Nordin Nur Afifah

Student Works (2020-2029)

Natural fibre composites (NFCs) are composite materials, in which the reinforcing fibres are derived from renewable and carbon dioxide neutral resources such as wood or plants. NFC can be made by replacing synthetic fibres with various types of natural fibres. Oil palm empty fruit bunch (OPEFB) fibre and oil palm mesocarp fibre are two important types of fibrous materials left in the palm-oil industry. In this study, EFB will be used as a reinforcement to the high-density polyethylene (HDPE). EFB was heat-treated at 180°C using vacuum oven for one hour, extrusion compounded with HDPE at 10%, 20% and 30% weight …

Synthesis And Characterization Of Porous Carbon Composite Derived From Biomass Waste For Supercapacitor Application, Cheng Kim Sim

Student Works (2020-2029)

Energy storage devices have gradually dominated human daily activities and indispensable to economy development such as supercapacitor and battery. There are few factors determining the performance of supercapacitor and active material is one of the crucial. Therefore, biomass such as pineapple peel (PP) and green waste (GW) were preferred and prior mixed with manganese and tin carbonate to synthesize carbon composite (PP/GW-ZMO and PP/GW-ZTO) via combustion. Brunauer–Emmett–Teller (BET) was employed to study the textural properties with the highest specific surface area obtained in PP-C (1765.92 m2g-1) and GW-C (1613.92 m2g-1). The existence of composite materials was examined using x-ray diffraction …

Effect Of Post-Consumer Content And Bioplastic Incorporation On Polymeric Resin In Consumer Applications, Shelby Bicknell

Electronic Theses & Dissertations

Controversy surrounds the use of plastic products, primarily due to their potentially negative impact on the environment at the end of their lifecycle. The most widely used plastics are manufactured from petrochemicals such as petroleum, coal or natural gas. Petrochemical plastics are not able to readily breakdown in the environment, which aggravates the existing pollution problems. Fortunately, there are eco-friendly alternatives to petrochemical-based plastics. Bioplastics may be derived from renewable sources, biodegradable, or both. Bio-based plastics are plastics that may be derived from renewable biomass sources including, but not limited to, vegetable oils, cornstarch, straw, woodchips, and food waste. They …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …

Investigation On The Morphology Of Charge-Transfer Complexes In Low Density Polyethylene, Wade Korf

Master's Theses

Fillers are used ubiquitously throughout the fields of polymer and material science to overcome many inherent limitations to polymeric materials (i.e. poor stiffness or strength) and to expand their potential applications. There is a need to develop controllable particle architectures to better understand fundamental structure-property relationships in particle reinforced polymer composites. Charge-transfer complexes (CTCs) can assemble in situ into various needle and dendritic shapes via simple fabrication processes and at low loading levels. In this study, the effect of tetrathiafulvalene (TTF) and 7,7,8,8-tetracyanoquinodimethane (TCNQ) CTC crystallites of various shapes and sizes on composite mechanical properties was investigated in an LDPE …

Gravity-Drawing Flexible Silicone Filaments As Fiber Optics And Model Foldamers, Katherine Snell

CMC Senior Theses

Here, we present a method of gravity-drawing polydimethylsiloxane (PDMS) silicone fibers with application as fiber optics and as model foldamers. Beginning as a viscous liquid, PDMS is cured using heat until its measured viscosity reaches 4000 mPa•s. The semi-cured elastomer is then extruded through a tube furnace to produce thin (diameters on the order of hundred micrometers) filaments with scalable lengths. PDMS is biocompatible, gas-permeable, flexible, and hydrophobic. Additionally, the PDMS surface hydrophobicity can be modified via UV exposure, O2 plasma, and corona discharge. We demonstrate the patternibility (i.e patterns of hydrophobicity) of PDMS fibers, adding complexity to potential foldamer …

Redox-Active Porous Organic Materials For Electrochemical Energy Storage Applications, K. Shamara Weeraratne

Theses and Dissertations

As the demand for renewable energy technologies grows, so does the need for cheaper, more efficient rechargeable batteries to store the energy. While lithium-ion battery (LIBs) technology is well established, it suffers from limited lithium supplies. Furthermore, the highly toxic transition metals used in the electrodes places a huge burden on the environment. Therefore, replacing lithium with more economical sodium metal in rechargeable batteries (i.e. sodium-ion batteries, SIBs) has garnered considerable attention. Despite the fact that sodium and lithium share similar electrochemical properties, which may cause the transition from lithium to sodium easier, the larger ionic radius of Na^{+ …}

Interfaces In Lead-Free Tin Perovskite Photovoltaics: An Investigation Of Energetics, Ion Mobility, Surface Modification, And Performance, Alex Boehm

Theses and Dissertations--Chemistry

Halide perovskites have generated tremendous interest as low-cost semiconductors for optoelectronics, such as photovoltaics, lasers, and light emitting diodes due to their extraordinary optical and transport properties. Perovskite photovoltaics in particular have demonstrated a meteoric rise in power conversion efficiencies and drawn considerable interest as a next-generation solar energy technology. The rapid development has centered around lead-based derivatives, and concerns regarding the toxicity of lead has sparked interest in low toxicity and more environmentally friendly perovskite derivatives. In this regime tin (Sn) is regarded as a prominent alternative owing to the ideal bandgap and reduced toxicity exhibited by Sn-halide perovskites. …

A Theoretical And Experimental Study Of Charge Transport In Organic Thermoelectric Materials And Charge Transfer States In Organic Photovoltaics, Ashkan Abtahi

Theses and Dissertations--Physics and Astronomy

Applications of organic electronics have increased significantly over the past two decades. Organic semiconductors (OSC) can be used in mechanically flexible devices with potentially lower cost of fabrication than their inorganic counterparts, yet in many cases organic semiconductor-based devices suffer from lower performance and stability. Investigating the doping mechanism, charge transport, and charge transfer in such materials will allow us to address the parameters that limit performance and potentially resolve them. In this dissertation, organic materials are used in three different device structures to investigate charge transport and charge transfer. Chemically doped π-conjugated polymers are promising materials to be used …

The Fabrication And Properties Of Magnetorheological Elastomers Employing Bio-Inspired Dopamine Modified Carbonyl Iron Particles, Yanfen Zhou, Lele Li, Wenyue Li, Shipeng Wen, Liang Jiang, Stephen Jerrams, Jianwei Ma, Shaojuan Chen

Articles

To obtain magnetorheological elastomers (MREs) with improved mechanical properties and exhibiting an enhanced magnetorheological (MR) effect, bio-inspired dopamine modification has been used to improve the functionality at the surface of carbonyl iron (CI) particles. Various techniques including x-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to confirm that a polydopamine (PDA) layer of about 27.5 nm had been successfully deposited on the surface of the carbonyl iron particles prior to their inclusion in the MRE composites. The magnetic properties of PDA modified CI particles were shown to be almost the same as those …

Enhanced Covalent Interface, Crosslinked Network And Gas Barrier Property Of Functionalized Graphene Oxide/Styrene-Butadiene Rubber Composites Triggered By Thiol-Ene Click Reaction, Long Zheng, Stephen Jerrams, Tian Su, Zongchao Xu, Liqun Zhang, Li Liu, Shipeng Wen

Articles

The high gas barrier property of a rubber composite is of great significance for reducing the exhaust gas emissions due to tire rolling resistance and hence the contribution this factor makes to environmental protection. Enhanced covalent interfaces and crosslinked networks are crucial to the gas barrier property of rubber composites. In this research, γ-mercaptopropyltriethoxysilane (MPS) modified GO (MGO)/styrene-butadiene rubber (SBR) composites were prepared by a synergetic strategy of latex compounding method and thiol-ene click reaction. It was found that the mercapto groups in MGO reacted with the vinyl groups in SBR molecules through thiol-ene click reaction during the crosslinking process …

Towards Completely Automated Glycan Synthesis, Matteo Panza

Dissertations

Carbohydrates are ubiquitous both in nature as biologically active compounds and in medicine as pharmaceuticals. Although there has been continued interest in the synthesis of carbohydrates, chemical methods require specialized knowledge and hence remain cumbersome. The need for development of rapid, efficient and operationally simple procedures has come to the fore. This dissertation focuses on the development of a fully automated platform that will enable both experts and non-specialists to perform the synthesis of glycans. Existing automated methods for the synthesis of oligosaccharides are highly sophisticated, operationally complex, and require significant user know-how. By contrast, high performance liquid chromatography (HPLC) …

Implementation Of Multivariate Artificial Neural Networks Coupled With Genetic Algorithms For The Multi-Objective Property Prediction And Optimization Of Emulsion Polymers, David Chisholm

Master's Theses

Machine learning has been gaining popularity over the past few decades as computers have become more advanced. On a fundamental level, machine learning consists of the use of computerized statistical methods to analyze data and discover trends that may not have been obvious or otherwise observable previously. These trends can then be used to make predictions on new data and explore entirely new design spaces. Methods vary from simple linear regression to highly complex neural networks, but the end goal is similar. The application of these methods to material property prediction and new material discovery has been of high interest …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Triperyleno[3,3,3]Propellane Triimides: Achieving A New Generation Of Quasi-D3h Symmetric Nanostructures In Organic Electronics, Lingling Lv, Josiah Roberts, Chengyi Xiao, Zhenmei Jia, Wei Jiang, Chad Risko, Lei Zhang

Chemistry Faculty Publications

Rigid three-dimensional (3D) polycyclic aromatic hydrocarbons (PAHs), in particular 3D nanographenes, have garnered interest due to their potential use in semiconductor applications and as models to study through-bond and through-space electronic interactions. Herein we report the development of a novel 3D-symmetric rylene imide building block, triperyleno[3,3,3]propellane triimides (6), that possesses three perylene monoimide subunits fused on a propellane. This building block shows several promising characteristics, including high solubility, large π-surfaces, electron-accepting capabilities, and a variety of reactive sites. Further, the building block is compatible with different reactions to readily yield quasi-D_3h symmetric nanostructures (9, …

“Polysoaps” Via Raft Copolymerization To Form Well-Defined Micelles For Water Remediation And Targeted Drug Delivery Applications, Phillip Pickett

Dissertations

Amphiphilic copolymers have become increasingly important for environmental and biological applications due to their behavioral characteristics in aqueous solution. For example, structurally-tailored statistical amphiphilic copolymers or “polysoaps” can self-assemble into micelles or other architectures in water at various concentrations. Polysoaps may be differentiated from small molecule surfactant micelles in their capability to self-assemble into unimolecular associates (unimolecular micelles) with no dependence on concentration. Such micelles offer enormous potential for dispersion of hydrophobic species in water at high dilution. Importantly, each polymer chain forms its own micelle and upon dilution, these micelles remain intact and capable of dispersing hydrocarbon material in …

Engineering Multifunctional And Morphologically Diverse Polymer Brush Surfaces, Cassandra M. Reese

Dissertations

The combination of surface-initiated polymerization (SIP) and post-polymerization (PPM) serves as a powerful approach to fabricate complex, multifunctional polymer films, which can be precisely tuned for desired surface engineering applications. Careful manipulation of PPM parameters such as reaction conditions, the tethered brush parameters, and the physical properties of the unbound post-modifier greatly influence the depth of penetration of the post-modifier and the polymer brush compositional heterogeneity. This dissertation focuses on engineering polymer brush surfaces with multifunctional chemistries and tunable morphologies by investigating the PPM parameters that dictate the distribution of post-modifiers on grafted polymer brush surfaces.

The first chapter of …

A Simple And Robust Approach To Reducing Contact Resistance In Organic Transistors, Zachary A. Lamport, Katrina J. Barth, Hyunsu Lee, Eliot Gann, Sebastian Engmann, Hu Chen, Martin Guthold, Iain Mcculloch, John E. Anthony, Lee J. Richter, Dean M. Delongchamp, Oana D. Jurchescu

Chemistry Faculty Publications

Efficient injection of charge carriers from the contacts into the semiconductor layer is crucial for achieving high-performance organic devices. The potential drop necessary to accomplish this process yields a resistance associated with the contacts, namely the contact resistance. A large contact resistance can limit the operation of devices and even lead to inaccuracies in the extraction of the device parameters. Here, we demonstrate a simple and efficient strategy for reducing the contact resistance in organic thin-film transistors by more than an order of magnitude by creating high work function domains at the surface of the injecting electrodes to promote channels …

Polyhedral Oligomeric Silsesquioxane-Phosphate Glass Matrix Nanocomposites With Additional Chapter On Phosphate Glass-Poly(Ethylene Terephthalate) Matrix Composites, Kyoungtae Kim

Dissertations

Preparation and characterization of tin fluorophosphate glass (Pglass) matrix nanocomposites incorporating polyhedral oligomeric silsesquioxane (POSS) were investigated on the structural, thermal, morphological, mechanical, and rheological properties. Various processes including synthesis, extrusion and sintering processes were applied to prepare the nanocomposite samples. Another application of POSS with hydrophobic functional groups on the well-structured nanoscale silicate cage with three silanol groups was investigated to present the feasibility to use POSS molecule as a coating material on the surface of the hydrophilic inorganic glass. In addition, Poly(ethylene terephthalate) polymer matrix composites incorporating Pglass was studied to present the benefits of the Pglass with …

Magnetic Ordering In A Vanadium-Organic Coordination Polymer Using A Pyrrolo[2,3-D:5,4-D']Bis(Thiazole)-Based Ligand, Yulia A. Getmanenko, Christopher S. Mullins, Vladimir N. Nesterov, Stephanie Lake, Chad Risko, Ezekiel Johnston-Halperin

Chemistry Faculty Publications

Here we present the synthesis and characterization of a hybrid vanadium-organic coordination polymer with robust magnetic order, a Curie temperature T_C of ∼110 K, a coercive field of ∼5 Oe at 5 K, and a maximum mass magnetization of about half that of the benchmark ferrimagnetic vanadium(tetracyanoethylene)_~2 (V·(TCNE)_~2). This material was prepared using a new tetracyano-substituted quinoidal organic small molecule 7 based on a tricyclic heterocycle 4-hexyl-4H-pyrrolo[2,3-d:5,4-d′]bis(thiazole) (C₆-PBTz). Single crystal X-ray diffraction of the 2,6-diiodo derivative of the parent C₆-PBTz, showed a disordered hexyl chain and …

Thienoisatin Oligomers As N-Type Molecular Semiconductors, Natalie M. Kadlubowski, Xuyi Luo, Jianguo Mei

The Summer Undergraduate Research Fellowship (SURF) Symposium

Organic field effect transistors (OFETs) offer many advantages compared to traditional inorganic transistors, such as flexibility and solution processability. In this study we design and synthesize two thienoisatin-based organic semiconducting small molecules, then investigate their electronic properties in n-type OFETs. To introduce n-type charge transport, electron-withdrawing dicarbonitrile moieties were installed on thienoisoindigo and bis-thienoisatin molecules, which led to a quinoidal conjugation on thienoisoindigo, while maintaining an aromatic conjugation on the bis-thienoisatin. Following the syntheses, the molecules were characterized to determine highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels via cyclic voltammetry, as well as any potential …

Glucosamine From Hydrolysis Of 3d Printing Chitosan For Osteoarthritis Treatment, Ruj Dansriboon, Laphon Premcharoen

The International Student Science Fair 2018

This project aims to introduce a new way for osteoarthritis treatment which is expected to increase in the future. Glucosamine is the main subject for a treatment, which can be derived by hydrolyzing chitosan. This project also includes extraction of chitosan from shrimp waste to make a worthy use of food waste from industry. In this project, 3D printer is applied to print chitosan gel since 3D printing is adjustable to form various shapes of the gel.

The research process begins with the extraction of chitosan from shrimp shells. For the next step, the percent of deacetylation of chitosan was …

Polymer Nanocomposites Containing High Aspect Ratio Particulates: Innovation In Co-Extruded Multilayer Barrier Films, Kevin Meyers

Dissertations

Delaminated montmorillonite (MMT) clay/ maleic anhydride grafted LLDPE nanocomposite multilayer films with alternating layers of LDPE were produced through multilayer co-extrusion. The MMT concentration within the nanocomposite layers was increased through annealing the films in the melt due to a mismatch in interdiffusion rates of the polymer layers. Analysis of the nanocomposite layers upon annealing revealed that the platelets impinged upon one another resulting in significant improvement in oxygen barrier in the multilayer system, exceeding the results of bulk nanocomposites.

Model analysis demonstrated that increasing the nanoplatelet aspect ratio or initial concentration in the filled layers would lead to even …

Highly Flame Retardant And Bio-Based Rigid Polyurethane Foams Derived From Orange Peel Oil, Chunyang Zhang

Electronic Theses & Dissertations

Polyurethane is an important class of polymer which is being used for various industrial applications in the form of rigid foams, flexible foams, thermoplastic, elastomer, coating, and adhesive. Especially there is a huge market for rigid polyurethane foams for their applications as thermal insulating material in building and housing. In general, polyurethanes are prepared using polyols and diisocyanates. Most of the polyols used by industries are petrochemical based. In this project, a novel polyol from an orange peel oil-based derivative, limonene dimercaptan, was synthesized using one step photochemical thiol-ene reaction. The synthesized polyol was used to prepare flame retardant polyurethane …

Surfactant Driven Assembly Of Freeze-Casted, Polymer-Derived Ceramic Nanoparticles On Grapehene Oxide Sheets For Lithium-Ion Battery Anodes, Ali Zein Khater

Honors Undergraduate Theses

Traditional Lithium-Ion Batteries (LIBs) are a reliable and cost-efficient choice for energy storage. LIBs offer high energy density and low self-discharge. Recent developments in electric-based technologies push for replacing historically used Lead-Acid batteries with LIBs. However, LIBs do not yet meet the demands of modern technology. Silicon and graphene oxide (GO) have been identified as promising replacements to improve anode materials. Graphene oxide has a unique sheet-like structure that provides a mechanically stable, light weight material for LIB anodes. Due to its structure, reduced graphene oxide (rGO) is efficiently conductive and resistive to environmental changes. On the other hand, silicon-based …